Merge remote-tracking branch 'stable/linux-6.1.y' into rpi-6.1.y

Documentation/ABI/testing/sysfs-class-net-statistics

@@ -1,4 +1,4 @@
-What:		/sys/class/<iface>/statistics/collisions
+What:		/sys/class/net/<iface>/statistics/collisions
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -6,7 +6,7 @@ Description:
 		Indicates the number of collisions seen by this network device.
 		This value might not be relevant with all MAC layers.
 
-What:		/sys/class/<iface>/statistics/multicast
+What:		/sys/class/net/<iface>/statistics/multicast
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -14,7 +14,7 @@ Description:
 		Indicates the number of multicast packets received by this
 		network device.
 
-What:		/sys/class/<iface>/statistics/rx_bytes
+What:		/sys/class/net/<iface>/statistics/rx_bytes
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -23,7 +23,7 @@ Description:
 		See the network driver for the exact meaning of when this
 		value is incremented.
 
-What:		/sys/class/<iface>/statistics/rx_compressed
+What:		/sys/class/net/<iface>/statistics/rx_compressed
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -32,7 +32,7 @@ Description:
 		network device. This value might only be relevant for interfaces
 		that support packet compression (e.g: PPP).
 
-What:		/sys/class/<iface>/statistics/rx_crc_errors
+What:		/sys/class/net/<iface>/statistics/rx_crc_errors
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -41,7 +41,7 @@ Description:
 		by this network device. Note that the specific meaning might
 		depend on the MAC layer used by the interface.
 
-What:		/sys/class/<iface>/statistics/rx_dropped
+What:		/sys/class/net/<iface>/statistics/rx_dropped
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -51,7 +51,7 @@ Description:
 		packet processing. See the network driver for the exact
 		meaning of this value.
 
-What:		/sys/class/<iface>/statistics/rx_errors
+What:		/sys/class/net/<iface>/statistics/rx_errors
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -59,7 +59,7 @@ Description:
 		Indicates the number of receive errors on this network device.
 		See the network driver for the exact meaning of this value.
 
-What:		/sys/class/<iface>/statistics/rx_fifo_errors
+What:		/sys/class/net/<iface>/statistics/rx_fifo_errors
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -68,7 +68,7 @@ Description:
 		network device. See the network driver for the exact
 		meaning of this value.
 
-What:		/sys/class/<iface>/statistics/rx_frame_errors
+What:		/sys/class/net/<iface>/statistics/rx_frame_errors
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -78,7 +78,7 @@ Description:
 		on the MAC layer protocol used. See the network driver for
 		the exact meaning of this value.
 
-What:		/sys/class/<iface>/statistics/rx_length_errors
+What:		/sys/class/net/<iface>/statistics/rx_length_errors
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -87,7 +87,7 @@ Description:
 		error, oversized or undersized. See the network driver for the
 		exact meaning of this value.
 
-What:		/sys/class/<iface>/statistics/rx_missed_errors
+What:		/sys/class/net/<iface>/statistics/rx_missed_errors
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -96,7 +96,7 @@ Description:
 		due to lack of capacity in the receive side. See the network
 		driver for the exact meaning of this value.
 
-What:		/sys/class/<iface>/statistics/rx_nohandler
+What:		/sys/class/net/<iface>/statistics/rx_nohandler
 Date:		February 2016
 KernelVersion:	4.6
 Contact:	netdev@vger.kernel.org
@@ -104,7 +104,7 @@ Description:
 		Indicates the number of received packets that were dropped on
 		an inactive device by the network core.
 
-What:		/sys/class/<iface>/statistics/rx_over_errors
+What:		/sys/class/net/<iface>/statistics/rx_over_errors
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -114,7 +114,7 @@ Description:
 		(e.g: larger than MTU). See the network driver for the exact
 		meaning of this value.
 
-What:		/sys/class/<iface>/statistics/rx_packets
+What:		/sys/class/net/<iface>/statistics/rx_packets
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -122,7 +122,7 @@ Description:
 		Indicates the total number of good packets received by this
 		network device.
 
-What:		/sys/class/<iface>/statistics/tx_aborted_errors
+What:		/sys/class/net/<iface>/statistics/tx_aborted_errors
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -132,7 +132,7 @@ Description:
 		a medium collision). See the network driver for the exact
 		meaning of this value.
 
-What:		/sys/class/<iface>/statistics/tx_bytes
+What:		/sys/class/net/<iface>/statistics/tx_bytes
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -143,7 +143,7 @@ Description:
 		transmitted packets or all packets that have been queued for
 		transmission.
 
-What:		/sys/class/<iface>/statistics/tx_carrier_errors
+What:		/sys/class/net/<iface>/statistics/tx_carrier_errors
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -152,7 +152,7 @@ Description:
 		because of carrier errors (e.g: physical link down). See the
 		network driver for the exact meaning of this value.
 
-What:		/sys/class/<iface>/statistics/tx_compressed
+What:		/sys/class/net/<iface>/statistics/tx_compressed
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -161,7 +161,7 @@ Description:
 		this might only be relevant for devices that support
 		compression (e.g: PPP).
 
-What:		/sys/class/<iface>/statistics/tx_dropped
+What:		/sys/class/net/<iface>/statistics/tx_dropped
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -170,7 +170,7 @@ Description:
 		See the driver for the exact reasons as to why the packets were
 		dropped.
 
-What:		/sys/class/<iface>/statistics/tx_errors
+What:		/sys/class/net/<iface>/statistics/tx_errors
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -179,7 +179,7 @@ Description:
 		a network device. See the driver for the exact reasons as to
 		why the packets were dropped.
 
-What:		/sys/class/<iface>/statistics/tx_fifo_errors
+What:		/sys/class/net/<iface>/statistics/tx_fifo_errors
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -188,7 +188,7 @@ Description:
 		FIFO error. See the driver for the exact reasons as to why the
 		packets were dropped.
 
-What:		/sys/class/<iface>/statistics/tx_heartbeat_errors
+What:		/sys/class/net/<iface>/statistics/tx_heartbeat_errors
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -197,7 +197,7 @@ Description:
 		reported as heartbeat errors. See the driver for the exact
 		reasons as to why the packets were dropped.
 
-What:		/sys/class/<iface>/statistics/tx_packets
+What:		/sys/class/net/<iface>/statistics/tx_packets
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org
@@ -206,7 +206,7 @@ Description:
 		device. See the driver for whether this reports the number of all
 		attempted or successful transmissions.
 
-What:		/sys/class/<iface>/statistics/tx_window_errors
+What:		/sys/class/net/<iface>/statistics/tx_window_errors
 Date:		April 2005
 KernelVersion:	2.6.12
 Contact:	netdev@vger.kernel.org

Documentation/ABI/testing/sysfs-devices-system-cpu

@@ -519,6 +519,7 @@ What:		/sys/devices/system/cpu/vulnerabilities
 		/sys/devices/system/cpu/vulnerabilities/mds
 		/sys/devices/system/cpu/vulnerabilities/meltdown
 		/sys/devices/system/cpu/vulnerabilities/mmio_stale_data
+		/sys/devices/system/cpu/vulnerabilities/reg_file_data_sampling
 		/sys/devices/system/cpu/vulnerabilities/retbleed
 		/sys/devices/system/cpu/vulnerabilities/spec_store_bypass
 		/sys/devices/system/cpu/vulnerabilities/spectre_v1

Documentation/admin-guide/hw-vuln/core-scheduling.rst

@@ -67,8 +67,8 @@ arg4:
     will be performed for all tasks in the task group of ``pid``.
 
 arg5:
-    userspace pointer to an unsigned long for storing the cookie returned by
-    ``PR_SCHED_CORE_GET`` command. Should be 0 for all other commands.
+    userspace pointer to an unsigned long long for storing the cookie returned
+    by ``PR_SCHED_CORE_GET`` command. Should be 0 for all other commands.
 
 In order for a process to push a cookie to, or pull a cookie from a process, it
 is required to have the ptrace access mode: `PTRACE_MODE_READ_REALCREDS` to the

Documentation/admin-guide/hw-vuln/index.rst

@@ -21,3 +21,4 @@ are configurable at compile, boot or run time.
    cross-thread-rsb.rst
    gather_data_sampling.rst
    srso
+   reg-file-data-sampling

Documentation/admin-guide/hw-vuln/reg-file-data-sampling.rst

@@ -0,0 +1,104 @@
+==================================
+Register File Data Sampling (RFDS)
+==================================
+
+Register File Data Sampling (RFDS) is a microarchitectural vulnerability that
+only affects Intel Atom parts(also branded as E-cores). RFDS may allow
+a malicious actor to infer data values previously used in floating point
+registers, vector registers, or integer registers. RFDS does not provide the
+ability to choose which data is inferred. CVE-2023-28746 is assigned to RFDS.
+
+Affected Processors
+===================
+Below is the list of affected Intel processors [#f1]_:
+
+   ===================  ============
+   Common name          Family_Model
+   ===================  ============
+   ATOM_GOLDMONT           06_5CH
+   ATOM_GOLDMONT_D         06_5FH
+   ATOM_GOLDMONT_PLUS      06_7AH
+   ATOM_TREMONT_D          06_86H
+   ATOM_TREMONT            06_96H
+   ALDERLAKE               06_97H
+   ALDERLAKE_L             06_9AH
+   ATOM_TREMONT_L          06_9CH
+   RAPTORLAKE              06_B7H
+   RAPTORLAKE_P            06_BAH
+   ATOM_GRACEMONT          06_BEH
+   RAPTORLAKE_S            06_BFH
+   ===================  ============
+
+As an exception to this table, Intel Xeon E family parts ALDERLAKE(06_97H) and
+RAPTORLAKE(06_B7H) codenamed Catlow are not affected. They are reported as
+vulnerable in Linux because they share the same family/model with an affected
+part. Unlike their affected counterparts, they do not enumerate RFDS_CLEAR or
+CPUID.HYBRID. This information could be used to distinguish between the
+affected and unaffected parts, but it is deemed not worth adding complexity as
+the reporting is fixed automatically when these parts enumerate RFDS_NO.
+
+Mitigation
+==========
+Intel released a microcode update that enables software to clear sensitive
+information using the VERW instruction. Like MDS, RFDS deploys the same
+mitigation strategy to force the CPU to clear the affected buffers before an
+attacker can extract the secrets. This is achieved by using the otherwise
+unused and obsolete VERW instruction in combination with a microcode update.
+The microcode clears the affected CPU buffers when the VERW instruction is
+executed.
+
+Mitigation points
+-----------------
+VERW is executed by the kernel before returning to user space, and by KVM
+before VMentry. None of the affected cores support SMT, so VERW is not required
+at C-state transitions.
+
+New bits in IA32_ARCH_CAPABILITIES
+----------------------------------
+Newer processors and microcode update on existing affected processors added new
+bits to IA32_ARCH_CAPABILITIES MSR. These bits can be used to enumerate
+vulnerability and mitigation capability:
+
+- Bit 27 - RFDS_NO - When set, processor is not affected by RFDS.
+- Bit 28 - RFDS_CLEAR - When set, processor is affected by RFDS, and has the
+  microcode that clears the affected buffers on VERW execution.
+
+Mitigation control on the kernel command line
+---------------------------------------------
+The kernel command line allows to control RFDS mitigation at boot time with the
+parameter "reg_file_data_sampling=". The valid arguments are:
+
+  ==========  =================================================================
+  on          If the CPU is vulnerable, enable mitigation; CPU buffer clearing
+              on exit to userspace and before entering a VM.
+  off         Disables mitigation.
+  ==========  =================================================================
+
+Mitigation default is selected by CONFIG_MITIGATION_RFDS.
+
+Mitigation status information
+-----------------------------
+The Linux kernel provides a sysfs interface to enumerate the current
+vulnerability status of the system: whether the system is vulnerable, and
+which mitigations are active. The relevant sysfs file is:
+
+	/sys/devices/system/cpu/vulnerabilities/reg_file_data_sampling
+
+The possible values in this file are:
+
+  .. list-table::
+
+     * - 'Not affected'
+       - The processor is not vulnerable
+     * - 'Vulnerable'
+       - The processor is vulnerable, but no mitigation enabled
+     * - 'Vulnerable: No microcode'
+       - The processor is vulnerable but microcode is not updated.
+     * - 'Mitigation: Clear Register File'
+       - The processor is vulnerable and the CPU buffer clearing mitigation is
+	 enabled.
+
+References
+----------
+.. [#f1] Affected Processors
+   https://www.intel.com/content/www/us/en/developer/topic-technology/software-security-guidance/processors-affected-consolidated-product-cpu-model.html

Documentation/admin-guide/hw-vuln/spectre.rst

@@ -138,11 +138,10 @@ associated with the source address of the indirect branch. Specifically,
 the BHB might be shared across privilege levels even in the presence of
 Enhanced IBRS.
 
-Currently the only known real-world BHB attack vector is via
-unprivileged eBPF. Therefore, it's highly recommended to not enable
-unprivileged eBPF, especially when eIBRS is used (without retpolines).
-For a full mitigation against BHB attacks, it's recommended to use
-retpolines (or eIBRS combined with retpolines).
+Previously the only known real-world BHB attack vector was via unprivileged
+eBPF. Further research has found attacks that don't require unprivileged eBPF.
+For a full mitigation against BHB attacks it is recommended to set BHI_DIS_S or
+use the BHB clearing sequence.
 
 Attack scenarios
 ----------------
@@ -430,6 +429,23 @@ The possible values in this file are:
   'PBRSB-eIBRS: Not affected'  CPU is not affected by PBRSB
   ===========================  =======================================================
 
+  - Branch History Injection (BHI) protection status:
+
+.. list-table::
+
+ * - BHI: Not affected
+   - System is not affected
+ * - BHI: Retpoline
+   - System is protected by retpoline
+ * - BHI: BHI_DIS_S
+   - System is protected by BHI_DIS_S
+ * - BHI: SW loop, KVM SW loop
+   - System is protected by software clearing sequence
+ * - BHI: Vulnerable
+   - System is vulnerable to BHI
+ * - BHI: Vulnerable, KVM: SW loop
+   - System is vulnerable; KVM is protected by software clearing sequence
+
 Full mitigation might require a microcode update from the CPU
 vendor. When the necessary microcode is not available, the kernel will
 report vulnerability.
@@ -484,11 +500,18 @@ Spectre variant 2
 
    Systems which support enhanced IBRS (eIBRS) enable IBRS protection once at
    boot, by setting the IBRS bit, and they're automatically protected against
-   Spectre v2 variant attacks, including cross-thread branch target injections
-   on SMT systems (STIBP). In other words, eIBRS enables STIBP too.
+   some Spectre v2 variant attacks. The BHB can still influence the choice of
+   indirect branch predictor entry, and although branch predictor entries are
+   isolated between modes when eIBRS is enabled, the BHB itself is not isolated
+   between modes. Systems which support BHI_DIS_S will set it to protect against
+   BHI attacks.
 
-   Legacy IBRS systems clear the IBRS bit on exit to userspace and
-   therefore explicitly enable STIBP for that
+   On Intel's enhanced IBRS systems, this includes cross-thread branch target
+   injections on SMT systems (STIBP). In other words, Intel eIBRS enables
+   STIBP, too.
+
+   AMD Automatic IBRS does not protect userspace, and Legacy IBRS systems clear
+   the IBRS bit on exit to userspace, therefore both explicitly enable STIBP.
 
    The retpoline mitigation is turned on by default on vulnerable
    CPUs. It can be forced on or off by the administrator
@@ -621,9 +644,9 @@ kernel command line.
                 retpoline,generic       Retpolines
                 retpoline,lfence        LFENCE; indirect branch
                 retpoline,amd           alias for retpoline,lfence
-                eibrs                   enhanced IBRS
-                eibrs,retpoline         enhanced IBRS + Retpolines
-                eibrs,lfence            enhanced IBRS + LFENCE
+                eibrs                   Enhanced/Auto IBRS
+                eibrs,retpoline         Enhanced/Auto IBRS + Retpolines
+                eibrs,lfence            Enhanced/Auto IBRS + LFENCE
                 ibrs                    use IBRS to protect kernel
 
 		Not specifying this option is equivalent to
@@ -635,6 +658,18 @@ kernel command line.
 		spectre_v2=off. Spectre variant 1 mitigations
 		cannot be disabled.
 
+	spectre_bhi=
+
+		[X86] Control mitigation of Branch History Injection
+		(BHI) vulnerability.  This setting affects the deployment
+		of the HW BHI control and the SW BHB clearing sequence.
+
+		on
+			(default) Enable the HW or SW mitigation as
+			needed.
+		off
+			Disable the mitigation.
+
 For spectre_v2_user see Documentation/admin-guide/kernel-parameters.txt
 
 Mitigation selection guide

Documentation/admin-guide/kernel-parameters.txt

@@ -1107,6 +1107,26 @@
 			The filter can be disabled or changed to another
 			driver later using sysfs.
 
+	reg_file_data_sampling=
+			[X86] Controls mitigation for Register File Data
+			Sampling (RFDS) vulnerability. RFDS is a CPU
+			vulnerability which may allow userspace to infer
+			kernel data values previously stored in floating point
+			registers, vector registers, or integer registers.
+			RFDS only affects Intel Atom processors.
+
+			on:	Turns ON the mitigation.
+			off:	Turns OFF the mitigation.
+
+			This parameter overrides the compile time default set
+			by CONFIG_MITIGATION_RFDS. Mitigation cannot be
+			disabled when other VERW based mitigations (like MDS)
+			are enabled. In order to disable RFDS mitigation all
+			VERW based mitigations need to be disabled.
+
+			For details see:
+			Documentation/admin-guide/hw-vuln/reg-file-data-sampling.rst
+
 	driver_async_probe=  [KNL]
 			List of driver names to be probed asynchronously. *
 			matches with all driver names. If * is specified, the
@@ -3186,9 +3206,7 @@
 
 	mem_encrypt=	[X86-64] AMD Secure Memory Encryption (SME) control
 			Valid arguments: on, off
-			Default (depends on kernel configuration option):
-			  on  (CONFIG_AMD_MEM_ENCRYPT_ACTIVE_BY_DEFAULT=y)
-			  off (CONFIG_AMD_MEM_ENCRYPT_ACTIVE_BY_DEFAULT=n)
+			Default: off
 			mem_encrypt=on:		Activate SME
 			mem_encrypt=off:	Do not activate SME
 
@@ -3262,8 +3280,10 @@
 					       nospectre_bhb [ARM64]
 					       nospectre_v1 [X86,PPC]
 					       nospectre_v2 [X86,PPC,S390,ARM64]
+					       reg_file_data_sampling=off [X86]
 					       retbleed=off [X86]
 					       spec_store_bypass_disable=off [X86,PPC]
+					       spectre_bhi=off [X86]
 					       spectre_v2_user=off [X86]
 					       srbds=off [X86,INTEL]
 					       ssbd=force-off [ARM64]
@@ -5714,6 +5734,15 @@
 	sonypi.*=	[HW] Sony Programmable I/O Control Device driver
 			See Documentation/admin-guide/laptops/sonypi.rst
 
+	spectre_bhi=	[X86] Control mitigation of Branch History Injection
+			(BHI) vulnerability.  This setting affects the
+			deployment of the HW BHI control and the SW BHB
+			clearing sequence.
+
+			on   - (default) Enable the HW or SW mitigation
+			       as needed.
+			off  - Disable the mitigation.
+
 	spectre_v2=	[X86] Control mitigation of Spectre variant 2
 			(indirect branch speculation) vulnerability.
 			The default operation protects the kernel from
@@ -5744,9 +5773,9 @@
 			retpoline,generic - Retpolines
 			retpoline,lfence  - LFENCE; indirect branch
 			retpoline,amd     - alias for retpoline,lfence
-			eibrs		  - enhanced IBRS
-			eibrs,retpoline   - enhanced IBRS + Retpolines
-			eibrs,lfence      - enhanced IBRS + LFENCE
+			eibrs		  - Enhanced/Auto IBRS
+			eibrs,retpoline   - Enhanced/Auto IBRS + Retpolines
+			eibrs,lfence      - Enhanced/Auto IBRS + LFENCE
 			ibrs		  - use IBRS to protect kernel
 
 			Not specifying this option is equivalent to
@@ -6574,6 +6603,9 @@
 					pause after every control message);
 				o = USB_QUIRK_HUB_SLOW_RESET (Hub needs extra
 					delay after resetting its port);
+				p = USB_QUIRK_SHORT_SET_ADDRESS_REQ_TIMEOUT
+					(Reduce timeout of the SET_ADDRESS
+					request from 5000 ms to 500 ms);
 			Example: quirks=0781:5580:bk,0a5c:5834:gij
 
 	usbhid.mousepoll=

Documentation/admin-guide/sysctl/net.rst

@@ -205,6 +205,11 @@ Will increase power usage.
 
 Default: 0 (off)
 
+mem_pcpu_rsv
+------------
+
+Per-cpu reserved forward alloc cache size in page units. Default 1MB per CPU.
+
 rmem_default
 ------------
 

Documentation/arm64/silicon-errata.rst

@@ -221,3 +221,10 @@ stable kernels.
 +----------------+-----------------+-----------------+-----------------------------+
 | Fujitsu        | A64FX           | E#010001        | FUJITSU_ERRATUM_010001      |
 +----------------+-----------------+-----------------+-----------------------------+
++----------------+-----------------+-----------------+-----------------------------+
+| Microsoft      | Azure Cobalt 100| #2139208        | ARM64_ERRATUM_2139208       |
++----------------+-----------------+-----------------+-----------------------------+
+| Microsoft      | Azure Cobalt 100| #2067961        | ARM64_ERRATUM_2067961       |
++----------------+-----------------+-----------------+-----------------------------+
+| Microsoft      | Azure Cobalt 100| #2253138        | ARM64_ERRATUM_2253138       |
++----------------+-----------------+-----------------+-----------------------------+

Documentation/devicetree/bindings/iio/health/maxim,max30102.yaml

@@ -42,7 +42,7 @@ allOf:
       properties:
         compatible:
           contains:
-            const: maxim,max30100
+            const: maxim,max30102
     then:
       properties:
         maxim,green-led-current-microamp: false

Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt

@@ -1,4 +1,4 @@
-Marvell 8787/8897/8997 (sd8787/sd8897/sd8997/pcie8997) SDIO/PCIE devices
+Marvell 8787/8897/8978/8997 (sd8787/sd8897/sd8978/sd8997/pcie8997) SDIO/PCIE devices
 ------
 
 This node provides properties for controlling the Marvell SDIO/PCIE wireless device.
@@ -10,7 +10,9 @@ Required properties:
   - compatible : should be one of the following:
 	* "marvell,sd8787"
 	* "marvell,sd8897"
+	* "marvell,sd8978"
 	* "marvell,sd8997"
+	* "nxp,iw416"
 	* "pci11ab,2b42"
 	* "pci1b4b,2b42"
 

Documentation/sphinx/kernel_include.py

@@ -97,7 +97,6 @@ class KernelInclude(Include):
         # HINT: this is the only line I had to change / commented out:
         #path = utils.relative_path(None, path)
 
-        path = nodes.reprunicode(path)
         encoding = self.options.get(
             'encoding', self.state.document.settings.input_encoding)
         e_handler=self.state.document.settings.input_encoding_error_handler

Documentation/userspace-api/media/mediactl/media-types.rst

@@ -375,12 +375,11 @@ Types and flags used to represent the media graph elements
 	  are origins of links.
 
     *  -  ``MEDIA_PAD_FL_MUST_CONNECT``
-       -  If this flag is set and the pad is linked to any other pad, then
-	  at least one of those links must be enabled for the entity to be
-	  able to stream. There could be temporary reasons (e.g. device
-	  configuration dependent) for the pad to need enabled links even
-	  when this flag isn't set; the absence of the flag doesn't imply
-	  there is none.
+       -  If this flag is set, then for this pad to be able to stream, it must
+	  be connected by at least one enabled link. There could be temporary
+	  reasons (e.g. device configuration dependent) for the pad to need
+	  enabled links even when this flag isn't set; the absence of the flag
+	  doesn't imply there is none.
 
 
 One and only one of ``MEDIA_PAD_FL_SINK`` and ``MEDIA_PAD_FL_SOURCE``

Documentation/x86/amd-memory-encryption.rst

@@ -87,14 +87,14 @@ The state of SME in the Linux kernel can be documented as follows:
 	  kernel is non-zero).
 
 SME can also be enabled and activated in the BIOS. If SME is enabled and
-activated in the BIOS, then all memory accesses will be encrypted and it will
-not be necessary to activate the Linux memory encryption support.  If the BIOS
-merely enables SME (sets bit 23 of the MSR_AMD64_SYSCFG), then Linux can activate
-memory encryption by default (CONFIG_AMD_MEM_ENCRYPT_ACTIVE_BY_DEFAULT=y) or
-by supplying mem_encrypt=on on the kernel command line.  However, if BIOS does
-not enable SME, then Linux will not be able to activate memory encryption, even
-if configured to do so by default or the mem_encrypt=on command line parameter
-is specified.
+activated in the BIOS, then all memory accesses will be encrypted and it
+will not be necessary to activate the Linux memory encryption support.
+
+If the BIOS merely enables SME (sets bit 23 of the MSR_AMD64_SYSCFG),
+then memory encryption can be enabled by supplying mem_encrypt=on on the
+kernel command line.  However, if BIOS does not enable SME, then Linux
+will not be able to activate memory encryption, even if configured to do
+so by default or the mem_encrypt=on command line parameter is specified.
 
 Secure Nested Paging (SNP)
 ==========================

Documentation/x86/boot.rst

@@ -1416,7 +1416,7 @@ execution context provided by the EFI firmware.
 
 The function prototype for the handover entry point looks like this::
 
-    efi_main(void *handle, efi_system_table_t *table, struct boot_params *bp)
+    efi_stub_entry(void *handle, efi_system_table_t *table, struct boot_params *bp)
 
 'handle' is the EFI image handle passed to the boot loader by the EFI
 firmware, 'table' is the EFI system table - these are the first two

Documentation/x86/mds.rst

@@ -95,6 +95,9 @@ The kernel provides a function to invoke the buffer clearing:
 
     mds_clear_cpu_buffers()
 
+Also macro CLEAR_CPU_BUFFERS can be used in ASM late in exit-to-user path.
+Other than CFLAGS.ZF, this macro doesn't clobber any registers.
+
 The mitigation is invoked on kernel/userspace, hypervisor/guest and C-state
 (idle) transitions.
 
@@ -138,17 +141,30 @@ Mitigation points
 
    When transitioning from kernel to user space the CPU buffers are flushed
    on affected CPUs when the mitigation is not disabled on the kernel
-   command line. The migitation is enabled through the static key
-   mds_user_clear.
+   command line. The mitigation is enabled through the feature flag
+   X86_FEATURE_CLEAR_CPU_BUF.
 
-   The mitigation is invoked in prepare_exit_to_usermode() which covers
-   all but one of the kernel to user space transitions.  The exception
-   is when we return from a Non Maskable Interrupt (NMI), which is
-   handled directly in do_nmi().
+   The mitigation is invoked just before transitioning to userspace after
+   user registers are restored. This is done to minimize the window in
+   which kernel data could be accessed after VERW e.g. via an NMI after
+   VERW.
 
-   (The reason that NMI is special is that prepare_exit_to_usermode() can
-    enable IRQs.  In NMI context, NMIs are blocked, and we don't want to
-    enable IRQs with NMIs blocked.)
+   **Corner case not handled**
+   Interrupts returning to kernel don't clear CPUs buffers since the
+   exit-to-user path is expected to do that anyways. But, there could be
+   a case when an NMI is generated in kernel after the exit-to-user path
+   has cleared the buffers. This case is not handled and NMI returning to
+   kernel don't clear CPU buffers because:
+
+   1. It is rare to get an NMI after VERW, but before returning to userspace.
+   2. For an unprivileged user, there is no known way to make that NMI
+      less rare or target it.
+   3. It would take a large number of these precisely-timed NMIs to mount
+      an actual attack.  There's presumably not enough bandwidth.
+   4. The NMI in question occurs after a VERW, i.e. when user state is
+      restored and most interesting data is already scrubbed. Whats left
+      is only the data that NMI touches, and that may or may not be of
+      any interest.
 
 
 2. C-State transition

MAINTAINERS

@@ -8070,7 +8070,7 @@ M:	Geoffrey D. Bennett <g@b4.vu>
 L:	alsa-devel@alsa-project.org (moderated for non-subscribers)
 S:	Maintained
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound.git
-F:	sound/usb/mixer_scarlett_gen2.c
+F:	sound/usb/mixer_scarlett2.c
 
 FORCEDETH GIGABIT ETHERNET DRIVER
 M:	Rain River <rain.1986.08.12@gmail.com>
@@ -10090,6 +10090,7 @@ F:	drivers/infiniband/
 F:	include/rdma/
 F:	include/trace/events/ib_mad.h
 F:	include/trace/events/ib_umad.h
+F:	include/trace/misc/rdma.h
 F:	include/uapi/linux/if_infiniband.h
 F:	include/uapi/rdma/
 F:	samples/bpf/ibumad_kern.c
@@ -11178,6 +11179,12 @@ F:	fs/nfs_common/
 F:	fs/nfsd/
 F:	include/linux/lockd/
 F:	include/linux/sunrpc/
+F:	include/trace/events/rpcgss.h
+F:	include/trace/events/rpcrdma.h
+F:	include/trace/events/sunrpc.h
+F:	include/trace/misc/fs.h
+F:	include/trace/misc/nfs.h
+F:	include/trace/misc/sunrpc.h
 F:	include/uapi/linux/nfsd/
 F:	include/uapi/linux/sunrpc/
 F:	net/sunrpc/
@@ -22638,6 +22645,7 @@ F:	include/xen/swiotlb-xen.h
 
 XFS FILESYSTEM
 C:	irc://irc.oftc.net/xfs
+M:	Leah Rumancik <leah.rumancik@gmail.com>
 M:	Darrick J. Wong <djwong@kernel.org>
 L:	linux-xfs@vger.kernel.org
 S:	Supported

Makefile

@@ -1,7 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0
 VERSION = 6
 PATCHLEVEL = 1
-SUBLEVEL = 77
+SUBLEVEL = 92
 EXTRAVERSION =
 NAME = Curry Ramen
 
@@ -459,8 +459,7 @@ HOSTRUSTC = rustc
 HOSTPKG_CONFIG	= pkg-config
 
 KBUILD_USERHOSTCFLAGS := -Wall -Wmissing-prototypes -Wstrict-prototypes \
-			 -O2 -fomit-frame-pointer -std=gnu11 \
-			 -Wdeclaration-after-statement
+			 -O2 -fomit-frame-pointer -std=gnu11
 KBUILD_USERCFLAGS  := $(KBUILD_USERHOSTCFLAGS) $(USERCFLAGS)
 KBUILD_USERLDFLAGS := $(USERLDFLAGS)
 
@@ -1018,9 +1017,6 @@ endif
 # arch Makefile may override CC so keep this after arch Makefile is included
 NOSTDINC_FLAGS += -nostdinc
 
-# warn about C99 declaration after statement
-KBUILD_CFLAGS += -Wdeclaration-after-statement
-
 # Variable Length Arrays (VLAs) should not be used anywhere in the kernel
 KBUILD_CFLAGS += -Wvla
 

arch/Kconfig

@@ -9,6 +9,14 @@
 #
 source "arch/$(SRCARCH)/Kconfig"
 
+config ARCH_CONFIGURES_CPU_MITIGATIONS
+	bool
+
+if !ARCH_CONFIGURES_CPU_MITIGATIONS
+config CPU_MITIGATIONS
+	def_bool y
+endif
+
 menu "General architecture-dependent options"
 
 config CRASH_CORE
@@ -642,6 +650,7 @@ config SHADOW_CALL_STACK
 	bool "Shadow Call Stack"
 	depends on ARCH_SUPPORTS_SHADOW_CALL_STACK
 	depends on DYNAMIC_FTRACE_WITH_ARGS || DYNAMIC_FTRACE_WITH_REGS || !FUNCTION_GRAPH_TRACER
+	depends on MMU
 	help
 	  This option enables the compiler's Shadow Call Stack, which
 	  uses a shadow stack to protect function return addresses from

arch/arc/boot/dts/hsdk.dts

@@ -205,7 +205,6 @@
 		};
 
 		gmac: ethernet@8000 {
-			#interrupt-cells = <1>;
 			compatible = "snps,dwmac";
 			reg = <0x8000 0x2000>;
 			interrupts = <10>;

arch/arc/include/asm/jump_label.h

@@ -31,7 +31,7 @@
 static __always_inline bool arch_static_branch(struct static_key *key,
 					       bool branch)
 {
-	asm_volatile_goto(".balign "__stringify(JUMP_LABEL_NOP_SIZE)"	\n"
+	asm goto(".balign "__stringify(JUMP_LABEL_NOP_SIZE)"		\n"
 		 "1:							\n"
 		 "nop							\n"
 		 ".pushsection __jump_table, \"aw\"			\n"
@@ -47,7 +47,7 @@ l_yes:
 static __always_inline bool arch_static_branch_jump(struct static_key *key,
 						    bool branch)
 {
-	asm_volatile_goto(".balign "__stringify(JUMP_LABEL_NOP_SIZE)"	\n"
+	asm goto(".balign "__stringify(JUMP_LABEL_NOP_SIZE)"		\n"
 		 "1:							\n"
 		 "b %l[l_yes]						\n"
 		 ".pushsection __jump_table, \"aw\"			\n"

arch/arm/boot/dts/arm-realview-pb1176.dts

@@ -451,7 +451,7 @@
 
 		/* Direct-mapped development chip ROM */
 		pb1176_rom@10200000 {
-			compatible = "direct-mapped";
+			compatible = "mtd-rom";
 			reg = <0x10200000 0x4000>;
 			bank-width = <1>;
 		};

arch/arm/boot/dts/at91-sama7g5ek.dts

@@ -293,7 +293,7 @@
 
 					regulator-state-standby {
 						regulator-on-in-suspend;
-						regulator-suspend-voltage = <1150000>;
+						regulator-suspend-microvolt = <1150000>;
 						regulator-mode = <4>;
 					};
 
@@ -314,7 +314,7 @@
 
 					regulator-state-standby {
 						regulator-on-in-suspend;
-						regulator-suspend-voltage = <1050000>;
+						regulator-suspend-microvolt = <1050000>;
 						regulator-mode = <4>;
 					};
 
@@ -331,7 +331,7 @@
 					regulator-always-on;
 
 					regulator-state-standby {
-						regulator-suspend-voltage = <1800000>;
+						regulator-suspend-microvolt = <1800000>;
 						regulator-on-in-suspend;
 					};
 
@@ -346,7 +346,7 @@
 					regulator-max-microvolt = <3700000>;
 
 					regulator-state-standby {
-						regulator-suspend-voltage = <1800000>;
+						regulator-suspend-microvolt = <1800000>;
 						regulator-on-in-suspend;
 					};
 

arch/arm/boot/dts/imx23.dtsi

@@ -59,7 +59,7 @@
 				reg = <0x80000000 0x2000>;
 			};
 
-			dma_apbh: dma-apbh@80004000 {
+			dma_apbh: dma-controller@80004000 {
 				compatible = "fsl,imx23-dma-apbh";
 				reg = <0x80004000 0x2000>;
 				interrupts = <0 14 20 0

arch/arm/boot/dts/imx28.dtsi

@@ -78,7 +78,7 @@
 				status = "disabled";
 			};
 
-			dma_apbh: dma-apbh@80004000 {
+			dma_apbh: dma-controller@80004000 {
 				compatible = "fsl,imx28-dma-apbh";
 				reg = <0x80004000 0x2000>;
 				interrupts = <82 83 84 85

arch/arm/boot/dts/imx6dl-yapp4-common.dtsi

@@ -106,8 +106,6 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii-id";
-	phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
-	phy-reset-duration = <20>;
 	phy-supply = <&sw2_reg>;
 	status = "okay";
 
@@ -120,17 +118,10 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		phy_port2: phy@1 {
-			reg = <1>;
-		};
-
-		phy_port3: phy@2 {
-			reg = <2>;
-		};
-
 		switch@10 {
 			compatible = "qca,qca8334";
-			reg = <10>;
+			reg = <0x10>;
+			reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
 
 			switch_ports: ports {
 				#address-cells = <1>;
@@ -151,15 +142,30 @@
 				eth2: port@2 {
 					reg = <2>;
 					label = "eth2";
+					phy-mode = "internal";
 					phy-handle = <&phy_port2>;
 				};
 
 				eth1: port@3 {
 					reg = <3>;
 					label = "eth1";
+					phy-mode = "internal";
 					phy-handle = <&phy_port3>;
 				};
 			};
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				phy_port2: ethernet-phy@1 {
+					reg = <1>;
+				};
+
+				phy_port3: ethernet-phy@2 {
+					reg = <2>;
+				};
+			};
 		};
 	};
 };

arch/arm/boot/dts/imx6q-apalis-ixora-v1.2.dts

@@ -76,6 +76,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_enable_can1_power>;
 		regulator-name = "can1_supply";
+		startup-delay-us = <1000>;
 	};
 
 	reg_can2_supply: regulator-can2-supply {
@@ -85,6 +86,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_enable_can2_power>;
 		regulator-name = "can2_supply";
+		startup-delay-us = <1000>;
 	};
 };
 

arch/arm/boot/dts/imx6qdl.dtsi

@@ -150,7 +150,7 @@
 		interrupt-parent = <&gpc>;
 		ranges;
 
-		dma_apbh: dma-apbh@110000 {
+		dma_apbh: dma-controller@110000 {
 			compatible = "fsl,imx6q-dma-apbh", "fsl,imx28-dma-apbh";
 			reg = <0x00110000 0x2000>;
 			interrupts = <0 13 IRQ_TYPE_LEVEL_HIGH>,

arch/arm/boot/dts/imx6sx.dtsi

@@ -209,7 +209,7 @@
 			power-domains = <&pd_pu>;
 		};
 
-		dma_apbh: dma-apbh@1804000 {
+		dma_apbh: dma-controller@1804000 {
 			compatible = "fsl,imx6sx-dma-apbh", "fsl,imx28-dma-apbh";
 			reg = <0x01804000 0x2000>;
 			interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,

arch/arm/boot/dts/imx6ul.dtsi

@@ -164,7 +164,7 @@
 			      <0x00a06000 0x2000>;
 		};
 
-		dma_apbh: dma-apbh@1804000 {
+		dma_apbh: dma-controller@1804000 {
 			compatible = "fsl,imx6q-dma-apbh", "fsl,imx28-dma-apbh";
 			reg = <0x01804000 0x2000>;
 			interrupts = <0 13 IRQ_TYPE_LEVEL_HIGH>,

arch/arm/boot/dts/imx7s.dtsi

@@ -1267,14 +1267,13 @@
 			};
 		};
 
-		dma_apbh: dma-apbh@33000000 {
+		dma_apbh: dma-controller@33000000 {
 			compatible = "fsl,imx7d-dma-apbh", "fsl,imx28-dma-apbh";
 			reg = <0x33000000 0x2000>;
 			interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "gpmi0", "gpmi1", "gpmi2", "gpmi3";
 			#dma-cells = <1>;
 			dma-channels = <4>;
 			clocks = <&clks IMX7D_NAND_USDHC_BUS_RAWNAND_CLK>;

arch/arm/boot/dts/mmp2-brownstone.dts

@@ -28,7 +28,7 @@
 &twsi1 {
 	status = "okay";
 	pmic: max8925@3c {
-		compatible = "maxium,max8925";
+		compatible = "maxim,max8925";
 		reg = <0x3c>;
 		interrupts = <1>;
 		interrupt-parent = <&intcmux4>;

arch/arm/boot/dts/qcom-msm8974.dtsi

@@ -1134,7 +1134,7 @@
 
 		qfprom: qfprom@fc4bc000 {
 			compatible = "qcom,msm8974-qfprom", "qcom,qfprom";
-			reg = <0xfc4bc000 0x1000>;
+			reg = <0xfc4bc000 0x2100>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			tsens_calib: calib@d0 {

arch/arm/boot/dts/r8a73a4-ape6evm.dts

@@ -209,6 +209,18 @@
 	status = "okay";
 };
 
+&extal1_clk {
+	clock-frequency = <26000000>;
+};
+
+&extal2_clk {
+	clock-frequency = <48000000>;
+};
+
+&extalr_clk {
+	clock-frequency = <32768>;
+};
+
 &pfc {
 	scifa0_pins: scifa0 {
 		groups = "scifa0_data";

arch/arm/boot/dts/r8a73a4.dtsi

@@ -450,17 +450,20 @@
 		extalr_clk: extalr {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
-			clock-frequency = <32768>;
+			/* This value must be overridden by the board. */
+			clock-frequency = <0>;
 		};
 		extal1_clk: extal1 {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
-			clock-frequency = <25000000>;
+			/* This value must be overridden by the board. */
+			clock-frequency = <0>;
 		};
 		extal2_clk: extal2 {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
-			clock-frequency = <48000000>;
+			/* This value must be overridden by the board. */
+			clock-frequency = <0>;
 		};
 		fsiack_clk: fsiack {
 			compatible = "fixed-clock";

arch/arm/crypto/sha256_glue.c

@@ -24,8 +24,8 @@
 
 #include "sha256_glue.h"
 
-asmlinkage void sha256_block_data_order(u32 *digest, const void *data,
-					unsigned int num_blks);
+asmlinkage void sha256_block_data_order(struct sha256_state *state,
+					const u8 *data, int num_blks);
 
 int crypto_sha256_arm_update(struct shash_desc *desc, const u8 *data,
 			     unsigned int len)
@@ -33,23 +33,20 @@ int crypto_sha256_arm_update(struct shash_desc *desc, const u8 *data,
 	/* make sure casting to sha256_block_fn() is safe */
 	BUILD_BUG_ON(offsetof(struct sha256_state, state) != 0);
 
-	return sha256_base_do_update(desc, data, len,
-				(sha256_block_fn *)sha256_block_data_order);
+	return sha256_base_do_update(desc, data, len, sha256_block_data_order);
 }
 EXPORT_SYMBOL(crypto_sha256_arm_update);
 
 static int crypto_sha256_arm_final(struct shash_desc *desc, u8 *out)
 {
-	sha256_base_do_finalize(desc,
-				(sha256_block_fn *)sha256_block_data_order);
+	sha256_base_do_finalize(desc, sha256_block_data_order);
 	return sha256_base_finish(desc, out);
 }
 
 int crypto_sha256_arm_finup(struct shash_desc *desc, const u8 *data,
 			    unsigned int len, u8 *out)
 {
-	sha256_base_do_update(desc, data, len,
-			      (sha256_block_fn *)sha256_block_data_order);
+	sha256_base_do_update(desc, data, len, sha256_block_data_order);
 	return crypto_sha256_arm_final(desc, out);
 }
 EXPORT_SYMBOL(crypto_sha256_arm_finup);

arch/arm/crypto/sha512-glue.c

@@ -25,27 +25,25 @@ MODULE_ALIAS_CRYPTO("sha512");
 MODULE_ALIAS_CRYPTO("sha384-arm");
 MODULE_ALIAS_CRYPTO("sha512-arm");
 
-asmlinkage void sha512_block_data_order(u64 *state, u8 const *src, int blocks);
+asmlinkage void sha512_block_data_order(struct sha512_state *state,
+					u8 const *src, int blocks);
 
 int sha512_arm_update(struct shash_desc *desc, const u8 *data,
 		      unsigned int len)
 {
-	return sha512_base_do_update(desc, data, len,
-		(sha512_block_fn *)sha512_block_data_order);
+	return sha512_base_do_update(desc, data, len, sha512_block_data_order);
 }
 
 static int sha512_arm_final(struct shash_desc *desc, u8 *out)
 {
-	sha512_base_do_finalize(desc,
-		(sha512_block_fn *)sha512_block_data_order);
+	sha512_base_do_finalize(desc, sha512_block_data_order);
 	return sha512_base_finish(desc, out);
 }
 
 int sha512_arm_finup(struct shash_desc *desc, const u8 *data,
 		     unsigned int len, u8 *out)
 {
-	sha512_base_do_update(desc, data, len,
-		(sha512_block_fn *)sha512_block_data_order);
+	sha512_base_do_update(desc, data, len, sha512_block_data_order);
 	return sha512_arm_final(desc, out);
 }
 

arch/arm/include/asm/jump_label.h

@@ -11,7 +11,7 @@
 
 static __always_inline bool arch_static_branch(struct static_key *key, bool branch)
 {
-	asm_volatile_goto("1:\n\t"
+	asm goto("1:\n\t"
 		 WASM(nop) "\n\t"
 		 ".pushsection __jump_table,  \"aw\"\n\t"
 		 ".word 1b, %l[l_yes], %c0\n\t"
@@ -25,7 +25,7 @@ l_yes:
 
 static __always_inline bool arch_static_branch_jump(struct static_key *key, bool branch)
 {
-	asm_volatile_goto("1:\n\t"
+	asm goto("1:\n\t"
 		 WASM(b) " %l[l_yes]\n\t"
 		 ".pushsection __jump_table,  \"aw\"\n\t"
 		 ".word 1b, %l[l_yes], %c0\n\t"

arch/arm/kernel/sleep.S

@@ -127,6 +127,10 @@ cpu_resume_after_mmu:
 	instr_sync
 #endif
 	bl	cpu_init		@ restore the und/abt/irq banked regs
+#if defined(CONFIG_KASAN) && defined(CONFIG_KASAN_STACK)
+	mov	r0, sp
+	bl	kasan_unpoison_task_stack_below
+#endif
 	mov	r0, #0			@ return zero on success
 	ldmfd	sp!, {r4 - r11, pc}
 ENDPROC(cpu_resume_after_mmu)

arch/arm/mach-ep93xx/core.c

@@ -339,6 +339,7 @@ static struct gpiod_lookup_table ep93xx_i2c_gpiod_table = {
 				GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
 		GPIO_LOOKUP_IDX("G", 0, NULL, 1,
 				GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
+		{ }
 	},
 };
 

arch/arm/mach-omap2/board-n8x0.c

@@ -22,7 +22,6 @@
 #include <linux/platform_data/spi-omap2-mcspi.h>
 #include <linux/platform_data/mmc-omap.h>
 #include <linux/mfd/menelaus.h>
-#include <sound/tlv320aic3x.h>
 
 #include <asm/mach/arch.h>
 #include <asm/mach-types.h>
@@ -567,10 +566,6 @@ struct menelaus_platform_data n8x0_menelaus_platform_data = {
 	.late_init = n8x0_menelaus_late_init,
 };
 
-struct aic3x_pdata n810_aic33_data = {
-	.gpio_reset = 118,
-};
-
 static int __init n8x0_late_initcall(void)
 {
 	if (!board_caps)

arch/arm/mach-omap2/common-board-devices.h

@@ -2,12 +2,10 @@
 #ifndef __OMAP_COMMON_BOARD_DEVICES__
 #define __OMAP_COMMON_BOARD_DEVICES__
 
-#include <sound/tlv320aic3x.h>
 #include <linux/mfd/menelaus.h>
 
 void *n8x0_legacy_init(void);
 
 extern struct menelaus_platform_data n8x0_menelaus_platform_data;
-extern struct aic3x_pdata n810_aic33_data;
 
 #endif /* __OMAP_COMMON_BOARD_DEVICES__ */

arch/arm/mach-omap2/pdata-quirks.c

@@ -440,7 +440,6 @@ static struct of_dev_auxdata omap_auxdata_lookup[] = {
 #ifdef CONFIG_MACH_NOKIA_N8X0
 	OF_DEV_AUXDATA("ti,omap2420-mmc", 0x4809c000, "mmci-omap.0", NULL),
 	OF_DEV_AUXDATA("menelaus", 0x72, "1-0072", &n8x0_menelaus_platform_data),
-	OF_DEV_AUXDATA("tlv320aic3x", 0x18, "2-0018", &n810_aic33_data),
 #endif
 #ifdef CONFIG_ARCH_OMAP3
 	OF_DEV_AUXDATA("ti,omap2-iommu", 0x5d000000, "5d000000.mmu",

arch/arm64/Kconfig

@@ -1752,7 +1752,6 @@ config ARM64_LSE_ATOMICS
 
 config ARM64_USE_LSE_ATOMICS
 	bool "Atomic instructions"
-	depends on JUMP_LABEL
 	default y
 	help
 	  As part of the Large System Extensions, ARMv8.1 introduces new

arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts

@@ -291,6 +291,8 @@
 };
 
 &spdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spdif_tx_pin>;
 	status = "okay";
 };
 

arch/arm64/boot/dts/allwinner/sun50i-h6-tanix.dtsi

@@ -166,6 +166,8 @@
 };
 
 &spdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spdif_tx_pin>;
 	status = "okay";
 };
 

arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi

@@ -406,6 +406,7 @@
 				function = "spi1";
 			};
 
+			/omit-if-no-ref/
 			spdif_tx_pin: spdif-tx-pin {
 				pins = "PH7";
 				function = "spdif";
@@ -655,10 +656,8 @@
 			clocks = <&ccu CLK_BUS_SPDIF>, <&ccu CLK_SPDIF>;
 			clock-names = "apb", "spdif";
 			resets = <&ccu RST_BUS_SPDIF>;
-			dmas = <&dma 2>;
-			dma-names = "tx";
-			pinctrl-names = "default";
-			pinctrl-0 = <&spdif_tx_pin>;
+			dmas = <&dma 2>, <&dma 2>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 

arch/arm64/boot/dts/amazon/alpine-v2.dtsi

@@ -145,7 +145,6 @@
 		msix: msix@fbe00000 {
 			compatible = "al,alpine-msix";
 			reg = <0x0 0xfbe00000 0x0 0x100000>;
-			interrupt-controller;
 			msi-controller;
 			al,msi-base-spi = <160>;
 			al,msi-num-spis = <160>;

arch/arm64/boot/dts/amazon/alpine-v3.dtsi

@@ -351,7 +351,6 @@
 		msix: msix@fbe00000 {
 			compatible = "al,alpine-msix";
 			reg = <0x0 0xfbe00000 0x0 0x100000>;
-			interrupt-controller;
 			msi-controller;
 			al,msi-base-spi = <336>;
 			al,msi-num-spis = <959>;

arch/arm64/boot/dts/broadcom/bcmbca/bcm4908.dtsi

@@ -180,9 +180,6 @@
 				brcm,num-gphy = <5>;
 				brcm,num-rgmii-ports = <2>;
 
-				#address-cells = <1>;
-				#size-cells = <0>;
-
 				ports: ports {
 					#address-cells = <1>;
 					#size-cells = <0>;

arch/arm64/boot/dts/broadcom/northstar2/ns2.dtsi

@@ -584,6 +584,7 @@
 			#gpio-cells = <2>;
 			gpio-controller;
 			interrupt-controller;
+			#interrupt-cells = <2>;
 			interrupts = <GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>;
 		};
 

arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi

@@ -442,6 +442,7 @@
 			#gpio-cells = <2>;
 			gpio-controller;
 			interrupt-controller;
+			#interrupt-cells = <2>;
 			interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>;
 			gpio-ranges = <&pinmux 0 0 16>,
 					<&pinmux 16 71 2>,

arch/arm64/boot/dts/freescale/imx8-ss-conn.dtsi

@@ -38,8 +38,8 @@ conn_subsys: bus@5b000000 {
 		interrupts = <GIC_SPI 232 IRQ_TYPE_LEVEL_HIGH>;
 		reg = <0x5b010000 0x10000>;
 		clocks = <&sdhc0_lpcg IMX_LPCG_CLK_4>,
-			 <&sdhc0_lpcg IMX_LPCG_CLK_0>,
-			 <&sdhc0_lpcg IMX_LPCG_CLK_5>;
+			 <&sdhc0_lpcg IMX_LPCG_CLK_5>,
+			 <&sdhc0_lpcg IMX_LPCG_CLK_0>;
 		clock-names = "ipg", "ahb", "per";
 		power-domains = <&pd IMX_SC_R_SDHC_0>;
 		status = "disabled";
@@ -49,8 +49,8 @@ conn_subsys: bus@5b000000 {
 		interrupts = <GIC_SPI 233 IRQ_TYPE_LEVEL_HIGH>;
 		reg = <0x5b020000 0x10000>;
 		clocks = <&sdhc1_lpcg IMX_LPCG_CLK_4>,
-			 <&sdhc1_lpcg IMX_LPCG_CLK_0>,
-			 <&sdhc1_lpcg IMX_LPCG_CLK_5>;
+			 <&sdhc1_lpcg IMX_LPCG_CLK_5>,
+			 <&sdhc1_lpcg IMX_LPCG_CLK_0>;
 		clock-names = "ipg", "ahb", "per";
 		power-domains = <&pd IMX_SC_R_SDHC_1>;
 		fsl,tuning-start-tap = <20>;
@@ -62,8 +62,8 @@ conn_subsys: bus@5b000000 {
 		interrupts = <GIC_SPI 234 IRQ_TYPE_LEVEL_HIGH>;
 		reg = <0x5b030000 0x10000>;
 		clocks = <&sdhc2_lpcg IMX_LPCG_CLK_4>,
-			 <&sdhc2_lpcg IMX_LPCG_CLK_0>,
-			 <&sdhc2_lpcg IMX_LPCG_CLK_5>;
+			 <&sdhc2_lpcg IMX_LPCG_CLK_5>,
+			 <&sdhc2_lpcg IMX_LPCG_CLK_0>;
 		clock-names = "ipg", "ahb", "per";
 		power-domains = <&pd IMX_SC_R_SDHC_2>;
 		status = "disabled";

arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts

@@ -294,8 +294,8 @@
 
 	pinctrl_i2c4: i2c4grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL			0x400001c3
-			MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA			0x400001c3
+			MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL			0x40000083
+			MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA			0x40000083
 		>;
 	};
 
@@ -313,19 +313,19 @@
 
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX		0x140
-			MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX		0x140
-			MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B		0x140
-			MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B		0x140
+			MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX		0x0
+			MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX		0x0
+			MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B		0x0
+			MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B		0x0
 		>;
 	};
 
 	pinctrl_uart2: uart2grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX		0x140
-			MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX		0x140
-			MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B		0x140
-			MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B		0x140
+			MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX		0x0
+			MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX		0x0
+			MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B		0x0
+			MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B		0x0
 		>;
 	};
 
@@ -337,40 +337,40 @@
 
 	pinctrl_usdhc2: usdhc2grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x190
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x90
 			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d0
 			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d0
 			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d0
 			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d0
 			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d0
-			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
-			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x19
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xd0
 		>;
 	};
 
 	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x194
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x94
 			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d4
 			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4
 			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4
 			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4
 			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4
-			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
-			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x19
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xd0
 		>;
 	};
 
 	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x196
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x96
 			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d6
 			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d6
 			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d6
 			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d6
 			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d6
-			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
-			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x19
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xd0
 		>;
 	};
 };

arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts

@@ -277,8 +277,8 @@
 
 	pinctrl_i2c4: i2c4grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL			0x400001c3
-			MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA			0x400001c3
+			MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL			0x40000083
+			MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA			0x40000083
 		>;
 	};
 
@@ -290,19 +290,19 @@
 
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX		0x140
-			MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX		0x140
-			MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B		0x140
-			MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B		0x140
+			MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX		0x0
+			MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX		0x0
+			MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B		0x0
+			MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B		0x0
 		>;
 	};
 
 	pinctrl_uart2: uart2grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX		0x140
-			MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX		0x140
-			MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B		0x140
-			MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B		0x140
+			MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX		0x0
+			MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX		0x0
+			MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B		0x0
+			MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B		0x0
 		>;
 	};
 
@@ -314,40 +314,40 @@
 
 	pinctrl_usdhc2: usdhc2grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x190
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x90
 			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d0
 			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d0
 			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d0
 			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d0
 			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d0
-			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
-			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x19
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xd0
 		>;
 	};
 
 	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x194
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x94
 			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d4
 			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4
 			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4
 			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4
 			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4
-			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
-			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x19
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xd0
 		>;
 	};
 
 	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x196
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x96
 			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d6
 			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d6
 			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d6
 			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d6
 			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d6
-			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
-			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x19
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xd0
 		>;
 	};
 };

arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi

@@ -205,7 +205,7 @@
 		reg = <0x52>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_rtc>;
-		interrupts-extended = <&gpio4 1 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts-extended = <&gpio4 1 IRQ_TYPE_LEVEL_LOW>;
 		trickle-diode-disable;
 	};
 };
@@ -247,8 +247,8 @@
 
 	pinctrl_i2c1: i2c1grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL			0x400001c3
-			MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x400001c3
+			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL			0x40000083
+			MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x40000083
 		>;
 	};
 

arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi

@@ -237,8 +237,8 @@
 
 	pinctrl_i2c1: i2c1grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL			0x400001c3
-			MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x400001c3
+			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL			0x40000083
+			MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x40000083
 		>;
 	};
 

arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi

@@ -47,17 +47,6 @@
 		gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>;
 		status = "okay";
 	};
-
-	reg_usb_otg1_vbus: regulator-usb-otg1 {
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_reg_usb1_en>;
-		compatible = "regulator-fixed";
-		regulator-name = "usb_otg1_vbus";
-		gpio = <&gpio1 10 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-	};
 };
 
 /* off-board header */
@@ -146,9 +135,10 @@
 };
 
 &usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg1>;
 	dr_mode = "otg";
 	over-current-active-low;
-	vbus-supply = <&reg_usb_otg1_vbus>;
 	status = "okay";
 };
 
@@ -206,14 +196,6 @@
 		>;
 	};
 
-	pinctrl_reg_usb1_en: regusb1grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10	0x41
-			MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12	0x141
-			MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC	0x41
-		>;
-	};
-
 	pinctrl_spi2: spi2grp {
 		fsl,pins = <
 			MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK	0xd6
@@ -236,4 +218,11 @@
 			MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX	0x140
 		>;
 	};
+
+	pinctrl_usbotg1: usbotg1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12	0x141
+			MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC	0x41
+		>;
+	};
 };

arch/arm64/boot/dts/lg/lg1312.dtsi

@@ -124,7 +124,6 @@
 	amba {
 		#address-cells = <2>;
 		#size-cells = <1>;
-		#interrupt-cells = <3>;
 
 		compatible = "simple-bus";
 		interrupt-parent = <&gic>;

arch/arm64/boot/dts/lg/lg1313.dtsi

@@ -124,7 +124,6 @@
 	amba {
 		#address-cells = <2>;
 		#size-cells = <1>;
-		#interrupt-cells = <3>;
 
 		compatible = "simple-bus";
 		interrupt-parent = <&gic>;

arch/arm64/boot/dts/marvell/armada-37xx.dtsi

@@ -426,14 +426,14 @@
 			crypto: crypto@90000 {
 				compatible = "inside-secure,safexcel-eip97ies";
 				reg = <0x90000 0x20000>;
-				interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
-					     <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
+				interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
 					     <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
 					     <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
 					     <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>,
-					     <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names = "mem", "ring0", "ring1",
-						  "ring2", "ring3", "eip";
+					     <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "ring0", "ring1", "ring2",
+						  "ring3", "eip", "mem";
 				clocks = <&nb_periph_clk 15>;
 			};
 

arch/arm64/boot/dts/marvell/armada-ap80x.dtsi

@@ -133,7 +133,6 @@
 
 			odmi: odmi@300000 {
 				compatible = "marvell,odmi-controller";
-				interrupt-controller;
 				msi-controller;
 				marvell,odmi-frames = <4>;
 				reg = <0x300000 0x4000>,

arch/arm64/boot/dts/marvell/armada-cp11x.dtsi

@@ -506,14 +506,14 @@
 		CP11X_LABEL(crypto): crypto@800000 {
 			compatible = "inside-secure,safexcel-eip197b";
 			reg = <0x800000 0x200000>;
-			interrupts = <87 IRQ_TYPE_LEVEL_HIGH>,
-				<88 IRQ_TYPE_LEVEL_HIGH>,
+			interrupts = <88 IRQ_TYPE_LEVEL_HIGH>,
 				<89 IRQ_TYPE_LEVEL_HIGH>,
 				<90 IRQ_TYPE_LEVEL_HIGH>,
 				<91 IRQ_TYPE_LEVEL_HIGH>,
-				<92 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "mem", "ring0", "ring1",
-				"ring2", "ring3", "eip";
+				<92 IRQ_TYPE_LEVEL_HIGH>,
+				<87 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "ring0", "ring1", "ring2", "ring3",
+					  "eip", "mem";
 			clock-names = "core", "reg";
 			clocks = <&CP11X_LABEL(clk) 1 26>,
 				 <&CP11X_LABEL(clk) 1 17>;

arch/arm64/boot/dts/mediatek/mt2712-evb.dts

@@ -128,7 +128,7 @@
 };
 
 &pio {
-	eth_default: eth_default {
+	eth_default: eth-default-pins {
 		tx_pins {
 			pinmux = <MT2712_PIN_71_GBE_TXD3__FUNC_GBE_TXD3>,
 				 <MT2712_PIN_72_GBE_TXD2__FUNC_GBE_TXD2>,
@@ -155,7 +155,7 @@
 		};
 	};
 
-	eth_sleep: eth_sleep {
+	eth_sleep: eth-sleep-pins {
 		tx_pins {
 			pinmux = <MT2712_PIN_71_GBE_TXD3__FUNC_GPIO71>,
 				 <MT2712_PIN_72_GBE_TXD2__FUNC_GPIO72>,
@@ -181,14 +181,14 @@
 		};
 	};
 
-	usb0_id_pins_float: usb0_iddig {
+	usb0_id_pins_float: usb0-iddig-pins {
 		pins_iddig {
 			pinmux = <MT2712_PIN_12_IDDIG_P0__FUNC_IDDIG_A>;
 			bias-pull-up;
 		};
 	};
 
-	usb1_id_pins_float: usb1_iddig {
+	usb1_id_pins_float: usb1-iddig-pins {
 		pins_iddig {
 			pinmux = <MT2712_PIN_14_IDDIG_P1__FUNC_IDDIG_B>;
 			bias-pull-up;

arch/arm64/boot/dts/mediatek/mt2712e.dtsi

@@ -249,10 +249,11 @@
 		#clock-cells = <1>;
 	};
 
-	infracfg: syscon@10001000 {
+	infracfg: clock-controller@10001000 {
 		compatible = "mediatek,mt2712-infracfg", "syscon";
 		reg = <0 0x10001000 0 0x1000>;
 		#clock-cells = <1>;
+		#reset-cells = <1>;
 	};
 
 	pericfg: syscon@10003000 {

arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts

@@ -74,6 +74,7 @@
 
 	memory@40000000 {
 		reg = <0 0x40000000 0 0x40000000>;
+		device_type = "memory";
 	};
 
 	reg_1p8v: regulator-1p8v {

arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts

@@ -56,6 +56,7 @@
 
 	memory@40000000 {
 		reg = <0 0x40000000 0 0x20000000>;
+		device_type = "memory";
 	};
 
 	reg_1p8v: regulator-1p8v {

arch/arm64/boot/dts/mediatek/mt7622.dtsi

@@ -251,7 +251,7 @@
 		clock-names = "hif_sel";
 	};
 
-	cir: cir@10009000 {
+	cir: ir-receiver@10009000 {
 		compatible = "mediatek,mt7622-cir";
 		reg = <0 0x10009000 0 0x1000>;
 		interrupts = <GIC_SPI 175 IRQ_TYPE_LEVEL_LOW>;
@@ -282,16 +282,14 @@
 		};
 	};
 
-	apmixedsys: apmixedsys@10209000 {
-		compatible = "mediatek,mt7622-apmixedsys",
-			     "syscon";
+	apmixedsys: clock-controller@10209000 {
+		compatible = "mediatek,mt7622-apmixedsys";
 		reg = <0 0x10209000 0 0x1000>;
 		#clock-cells = <1>;
 	};
 
-	topckgen: topckgen@10210000 {
-		compatible = "mediatek,mt7622-topckgen",
-			     "syscon";
+	topckgen: clock-controller@10210000 {
+		compatible = "mediatek,mt7622-topckgen";
 		reg = <0 0x10210000 0 0x1000>;
 		#clock-cells = <1>;
 	};
@@ -514,7 +512,6 @@
 			 <&pericfg CLK_PERI_AUXADC_PD>;
 		clock-names = "therm", "auxadc";
 		resets = <&pericfg MT7622_PERI_THERM_SW_RST>;
-		reset-names = "therm";
 		mediatek,auxadc = <&auxadc>;
 		mediatek,apmixedsys = <&apmixedsys>;
 		nvmem-cells = <&thermal_calibration>;
@@ -734,9 +731,8 @@
 		power-domains = <&scpsys MT7622_POWER_DOMAIN_WB>;
 	};
 
-	ssusbsys: ssusbsys@1a000000 {
-		compatible = "mediatek,mt7622-ssusbsys",
-			     "syscon";
+	ssusbsys: clock-controller@1a000000 {
+		compatible = "mediatek,mt7622-ssusbsys";
 		reg = <0 0x1a000000 0 0x1000>;
 		#clock-cells = <1>;
 		#reset-cells = <1>;
@@ -793,9 +789,8 @@
 		};
 	};
 
-	pciesys: pciesys@1a100800 {
-		compatible = "mediatek,mt7622-pciesys",
-			     "syscon";
+	pciesys: clock-controller@1a100800 {
+		compatible = "mediatek,mt7622-pciesys";
 		reg = <0 0x1a100800 0 0x1000>;
 		#clock-cells = <1>;
 		#reset-cells = <1>;
@@ -921,12 +916,13 @@
 		};
 	};
 
-	hifsys: syscon@1af00000 {
-		compatible = "mediatek,mt7622-hifsys", "syscon";
+	hifsys: clock-controller@1af00000 {
+		compatible = "mediatek,mt7622-hifsys";
 		reg = <0 0x1af00000 0 0x70>;
+		#clock-cells = <1>;
 	};
 
-	ethsys: syscon@1b000000 {
+	ethsys: clock-controller@1b000000 {
 		compatible = "mediatek,mt7622-ethsys",
 			     "syscon";
 		reg = <0 0x1b000000 0 0x1000>;
@@ -966,9 +962,7 @@
 	};
 
 	eth: ethernet@1b100000 {
-		compatible = "mediatek,mt7622-eth",
-			     "mediatek,mt2701-eth",
-			     "syscon";
+		compatible = "mediatek,mt7622-eth";
 		reg = <0 0x1b100000 0 0x20000>;
 		interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_LOW>,
 			     <GIC_SPI 224 IRQ_TYPE_LEVEL_LOW>,

arch/arm64/boot/dts/mediatek/mt7986a.dtsi

@@ -110,6 +110,7 @@
 			compatible = "mediatek,mt7986-infracfg", "syscon";
 			reg = <0 0x10001000 0 0x1000>;
 			#clock-cells = <1>;
+			#reset-cells = <1>;
 		};
 
 		wed_pcie: wed-pcie@10003000 {

arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi.dtsi

@@ -4,6 +4,8 @@
  */
 
 #include "mt8183-kukui.dtsi"
+/* Must come after mt8183-kukui.dtsi to modify cros_ec */
+#include <arm/cros-ec-keyboard.dtsi>
 
 / {
 	panel: panel {

arch/arm64/boot/dts/mediatek/mt8183-kukui-kakadu.dtsi

@@ -372,6 +372,16 @@
 	};
 };
 
+&cros_ec {
+	cbas {
+		compatible = "google,cros-cbas";
+	};
+
+	keyboard-controller {
+		compatible = "google,cros-ec-keyb-switches";
+	};
+};
+
 &qca_wifi {
 	qcom,ath10k-calibration-variant = "GO_KAKADU";
 };

arch/arm64/boot/dts/mediatek/mt8183-kukui-kodama.dtsi

@@ -339,6 +339,16 @@
 	};
 };
 
+&cros_ec {
+	cbas {
+		compatible = "google,cros-cbas";
+	};
+
+	keyboard-controller {
+		compatible = "google,cros-ec-keyb-switches";
+	};
+};
+
 &qca_wifi {
 	qcom,ath10k-calibration-variant = "GO_KODAMA";
 };

arch/arm64/boot/dts/mediatek/mt8183-kukui-krane.dtsi

@@ -343,6 +343,16 @@
 	};
 };
 
+&cros_ec {
+	cbas {
+		compatible = "google,cros-cbas";
+	};
+
+	keyboard-controller {
+		compatible = "google,cros-ec-keyb-switches";
+	};
+};
+
 &qca_wifi {
 	qcom,ath10k-calibration-variant = "LE_Krane";
 };

arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi

@@ -896,10 +896,6 @@
 			google,usb-port-id = <0>;
 		};
 
-		cbas {
-			compatible = "google,cros-cbas";
-		};
-
 		typec {
 			compatible = "google,cros-ec-typec";
 			#address-cells = <1>;
@@ -999,5 +995,4 @@
 	};
 };
 
-#include <arm/cros-ec-keyboard.dtsi>
 #include <arm/cros-ec-sbs.dtsi>

arch/arm64/boot/dts/mediatek/mt8183.dtsi

@@ -1554,6 +1554,7 @@
 			compatible = "mediatek,mt8183-mfgcfg", "syscon";
 			reg = <0 0x13000000 0 0x1000>;
 			#clock-cells = <1>;
+			power-domains = <&spm MT8183_POWER_DOMAIN_MFG_ASYNC>;
 		};
 
 		gpu: gpu@13040000 {

arch/arm64/boot/dts/mediatek/mt8192-asurada.dtsi

@@ -819,10 +819,6 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		base_detection: cbas {
-			compatible = "google,cros-cbas";
-		};
-
 		cros_ec_pwm: pwm {
 			compatible = "google,cros-ec-pwm";
 			#pwm-cells = <1>;
@@ -907,7 +903,7 @@
 			mt6315_6_vbuck1: vbuck1 {
 				regulator-compatible = "vbuck1";
 				regulator-name = "Vbcpu";
-				regulator-min-microvolt = <300000>;
+				regulator-min-microvolt = <400000>;
 				regulator-max-microvolt = <1193750>;
 				regulator-enable-ramp-delay = <256>;
 				regulator-allowed-modes = <0 1 2>;
@@ -917,7 +913,7 @@
 			mt6315_6_vbuck3: vbuck3 {
 				regulator-compatible = "vbuck3";
 				regulator-name = "Vlcpu";
-				regulator-min-microvolt = <300000>;
+				regulator-min-microvolt = <400000>;
 				regulator-max-microvolt = <1193750>;
 				regulator-enable-ramp-delay = <256>;
 				regulator-allowed-modes = <0 1 2>;
@@ -934,7 +930,7 @@
 			mt6315_7_vbuck1: vbuck1 {
 				regulator-compatible = "vbuck1";
 				regulator-name = "Vgpu";
-				regulator-min-microvolt = <606250>;
+				regulator-min-microvolt = <400000>;
 				regulator-max-microvolt = <800000>;
 				regulator-enable-ramp-delay = <256>;
 				regulator-allowed-modes = <0 1 2>;

arch/arm64/boot/dts/mediatek/mt8192.dtsi

@@ -1240,6 +1240,7 @@
 			reg = <0 0x14001000 0 0x1000>;
 			interrupts = <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH 0>;
 			clocks = <&mmsys CLK_MM_DISP_MUTEX0>;
+			mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0x1000 0x1000>;
 			mediatek,gce-events = <CMDQ_EVENT_DISP_STREAM_DONE_ENG_EVENT_0>,
 					      <CMDQ_EVENT_DISP_STREAM_DONE_ENG_EVENT_1>;
 			power-domains = <&spm MT8192_POWER_DOMAIN_DISP>;
@@ -1539,7 +1540,7 @@
 			mediatek,scp = <&scp>;
 			power-domains = <&spm MT8192_POWER_DOMAIN_VENC>;
 			clocks = <&vencsys CLK_VENC_SET1_VENC>;
-			clock-names = "venc-set1";
+			clock-names = "venc_sel";
 			assigned-clocks = <&topckgen CLK_TOP_VENC_SEL>;
 			assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL_D4>;
 		};

arch/arm64/boot/dts/mediatek/mt8195-cherry-tomato-r1.dts

@@ -13,3 +13,7 @@
 &ts_10 {
 	status = "okay";
 };
+
+&watchdog {
+	/delete-property/ mediatek,disable-extrst;
+};

arch/arm64/boot/dts/mediatek/mt8195-cherry-tomato-r2.dts

@@ -33,3 +33,7 @@
 &ts_10 {
 	status = "okay";
 };
+
+&watchdog {
+	/delete-property/ mediatek,disable-extrst;
+};

arch/arm64/boot/dts/mediatek/mt8195-cherry-tomato-r3.dts

@@ -34,3 +34,7 @@
 &ts_10 {
 	status = "okay";
 };
+
+&watchdog {
+	/delete-property/ mediatek,disable-extrst;
+};

arch/arm64/boot/dts/mediatek/mt8195-cherry.dtsi

@@ -845,7 +845,7 @@
 			mt6315_6_vbuck1: vbuck1 {
 				regulator-compatible = "vbuck1";
 				regulator-name = "Vbcpu";
-				regulator-min-microvolt = <300000>;
+				regulator-min-microvolt = <400000>;
 				regulator-max-microvolt = <1193750>;
 				regulator-enable-ramp-delay = <256>;
 				regulator-ramp-delay = <6250>;
@@ -863,7 +863,7 @@
 			mt6315_7_vbuck1: vbuck1 {
 				regulator-compatible = "vbuck1";
 				regulator-name = "Vgpu";
-				regulator-min-microvolt = <625000>;
+				regulator-min-microvolt = <400000>;
 				regulator-max-microvolt = <1193750>;
 				regulator-enable-ramp-delay = <256>;
 				regulator-ramp-delay = <6250>;

arch/arm64/boot/dts/mediatek/mt8195-demo.dts

@@ -111,6 +111,7 @@
 		compatible = "mediatek,mt6360";
 		reg = <0x34>;
 		interrupt-controller;
+		#interrupt-cells = <1>;
 		interrupts-extended = <&pio 101 IRQ_TYPE_EDGE_FALLING>;
 		interrupt-names = "IRQB";
 

arch/arm64/boot/dts/mediatek/mt8195.dtsi

@@ -1492,6 +1492,7 @@
 			compatible = "mediatek,mt8195-vppsys0";
 			reg = <0 0x14000000 0 0x1000>;
 			#clock-cells = <1>;
+			mediatek,gce-client-reg = <&gce1 SUBSYS_1400XXXX 0 0x1000>;
 		};
 
 		smi_sub_common_vpp0_vpp1_2x1: smi@14010000 {
@@ -1597,6 +1598,7 @@
 			compatible = "mediatek,mt8195-vppsys1";
 			reg = <0 0x14f00000 0 0x1000>;
 			#clock-cells = <1>;
+			mediatek,gce-client-reg = <&gce1 SUBSYS_14f0XXXX 0 0x1000>;
 		};
 
 		larb5: larb@14f02000 {
@@ -1982,6 +1984,7 @@
 			reg = <0 0x1c01a000 0 0x1000>;
 			mboxes = <&gce0 0 CMDQ_THR_PRIO_4>;
 			#clock-cells = <1>;
+			mediatek,gce-client-reg = <&gce0 SUBSYS_1c01XXXX 0xa000 0x1000>;
 		};
 
 		larb20: larb@1b010000 {
@@ -2085,6 +2088,7 @@
 			interrupts = <GIC_SPI 658 IRQ_TYPE_LEVEL_HIGH 0>;
 			power-domains = <&spm MT8195_POWER_DOMAIN_VDOSYS0>;
 			clocks = <&vdosys0 CLK_VDO0_DISP_MUTEX0>;
+			mediatek,gce-client-reg = <&gce0 SUBSYS_1c01XXXX 0x6000 0x1000>;
 			mediatek,gce-events = <CMDQ_EVENT_VDO0_DISP_STREAM_DONE_0>;
 		};
 

arch/arm64/boot/dts/nvidia/tegra234-p3737-0000+p3701-0000.dts

@@ -2024,7 +2024,7 @@
 			status = "okay";
 
 			phy-handle = <&mgbe0_phy>;
-			phy-mode = "usxgmii";
+			phy-mode = "10gbase-r";
 
 			mdio {
 				#address-cells = <1>;

arch/arm64/boot/dts/qcom/apq8016-sbc.dts

@@ -169,10 +169,6 @@
 	};
 };
 
-&blsp_dma {
-	status = "okay";
-};
-
 &blsp_i2c2 {
 	/* On Low speed expansion */
 	status = "okay";

arch/arm64/boot/dts/qcom/msm8916.dtsi

@@ -1522,7 +1522,7 @@
 			clock-names = "bam_clk";
 			#dma-cells = <1>;
 			qcom,ee = <0>;
-			status = "disabled";
+			qcom,controlled-remotely;
 		};
 
 		blsp1_uart1: serial@78af000 {

arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi

@@ -923,6 +923,8 @@ ap_spi_fp: &spi10 {
 		vddrf-supply = <&pp1300_l2c>;
 		vddch0-supply = <&pp3300_l10c>;
 		max-speed = <3200000>;
+
+		qcom,local-bd-address-broken;
 	};
 };
 

arch/arm64/boot/dts/qcom/sc7280.dtsi

@@ -2028,8 +2028,16 @@
 			ranges = <0x01000000 0x0 0x00000000 0x0 0x40200000 0x0 0x100000>,
 				 <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x1fd00000>;
 
-			interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "msi";
+			interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 374 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 375 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi0", "msi1", "msi2", "msi3",
+					  "msi4", "msi5", "msi6", "msi7";
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 0x7>;
 			interrupt-map = <0 0 0 1 &intc 0 0 0 434 IRQ_TYPE_LEVEL_HIGH>,

arch/arm64/boot/dts/qcom/sdm845-db845c.dts

@@ -532,7 +532,7 @@
 &pcie0 {
 	status = "okay";
 	perst-gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
-	enable-gpio = <&tlmm 134 GPIO_ACTIVE_HIGH>;
+	wake-gpios = <&tlmm 134 GPIO_ACTIVE_HIGH>;
 
 	vddpe-3v3-supply = <&pcie0_3p3v_dual>;
 

arch/arm64/boot/dts/qcom/sdm845.dtsi

@@ -4049,7 +4049,7 @@
 			assigned-clock-rates = <19200000>, <150000000>;
 
 			interrupts-extended = <&intc GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
-					      <&intc GIC_SPI 486 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc_intc 6 IRQ_TYPE_LEVEL_HIGH>,
 					      <&pdc_intc 8 IRQ_TYPE_EDGE_BOTH>,
 					      <&pdc_intc 9 IRQ_TYPE_EDGE_BOTH>;
 			interrupt-names = "hs_phy_irq", "ss_phy_irq",
@@ -4100,7 +4100,7 @@
 			assigned-clock-rates = <19200000>, <150000000>;
 
 			interrupts-extended = <&intc GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
-					      <&intc GIC_SPI 487 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc_intc 7 IRQ_TYPE_LEVEL_HIGH>,
 					      <&pdc_intc 10 IRQ_TYPE_EDGE_BOTH>,
 					      <&pdc_intc 11 IRQ_TYPE_EDGE_BOTH>;
 			interrupt-names = "hs_phy_irq", "ss_phy_irq",

arch/arm64/boot/dts/qcom/sm8150.dtsi

@@ -1822,8 +1822,8 @@
 			phys = <&pcie0_lane>;
 			phy-names = "pciephy";
 
-			perst-gpio = <&tlmm 35 GPIO_ACTIVE_HIGH>;
-			enable-gpio = <&tlmm 37 GPIO_ACTIVE_HIGH>;
+			perst-gpios = <&tlmm 35 GPIO_ACTIVE_HIGH>;
+			wake-gpios = <&tlmm 37 GPIO_ACTIVE_HIGH>;
 
 			pinctrl-names = "default";
 			pinctrl-0 = <&pcie0_default_state>;
@@ -1925,7 +1925,7 @@
 			phys = <&pcie1_lane>;
 			phy-names = "pciephy";
 
-			perst-gpio = <&tlmm 102 GPIO_ACTIVE_HIGH>;
+			perst-gpios = <&tlmm 102 GPIO_ACTIVE_HIGH>;
 			enable-gpio = <&tlmm 104 GPIO_ACTIVE_HIGH>;
 
 			pinctrl-names = "default";
@@ -3629,7 +3629,7 @@
 			assigned-clock-rates = <19200000>, <200000000>;
 
 			interrupts-extended = <&intc GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
-					      <&intc GIC_SPI 486 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 6 IRQ_TYPE_LEVEL_HIGH>,
 					      <&pdc 8 IRQ_TYPE_EDGE_BOTH>,
 					      <&pdc 9 IRQ_TYPE_EDGE_BOTH>;
 			interrupt-names = "hs_phy_irq", "ss_phy_irq",
@@ -3678,7 +3678,7 @@
 			assigned-clock-rates = <19200000>, <200000000>;
 
 			interrupts-extended = <&intc GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
-					      <&intc GIC_SPI 487 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 7 IRQ_TYPE_LEVEL_HIGH>,
 					      <&pdc 10 IRQ_TYPE_EDGE_BOTH>,
 					      <&pdc 11 IRQ_TYPE_EDGE_BOTH>;
 			interrupt-names = "hs_phy_irq", "ss_phy_irq",

arch/arm64/boot/dts/renesas/r8a779a0.dtsi

@@ -656,8 +656,8 @@
 
 		avb0: ethernet@e6800000 {
 			compatible = "renesas,etheravb-r8a779a0",
-				     "renesas,etheravb-rcar-gen3";
-			reg = <0 0xe6800000 0 0x800>;
+				     "renesas,etheravb-rcar-gen4";
+			reg = <0 0xe6800000 0 0x1000>;
 			interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 257 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 258 IRQ_TYPE_LEVEL_HIGH>,
@@ -704,8 +704,8 @@
 
 		avb1: ethernet@e6810000 {
 			compatible = "renesas,etheravb-r8a779a0",
-				     "renesas,etheravb-rcar-gen3";
-			reg = <0 0xe6810000 0 0x800>;
+				     "renesas,etheravb-rcar-gen4";
+			reg = <0 0xe6810000 0 0x1000>;
 			interrupts = <GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
@@ -752,7 +752,7 @@
 
 		avb2: ethernet@e6820000 {
 			compatible = "renesas,etheravb-r8a779a0",
-				     "renesas,etheravb-rcar-gen3";
+				     "renesas,etheravb-rcar-gen4";
 			reg = <0 0xe6820000 0 0x1000>;
 			interrupts = <GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>,
 					<GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>,
@@ -800,7 +800,7 @@
 
 		avb3: ethernet@e6830000 {
 			compatible = "renesas,etheravb-r8a779a0",
-				     "renesas,etheravb-rcar-gen3";
+				     "renesas,etheravb-rcar-gen4";
 			reg = <0 0xe6830000 0 0x1000>;
 			interrupts = <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
 					<GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>,
@@ -848,7 +848,7 @@
 
 		avb4: ethernet@e6840000 {
 			compatible = "renesas,etheravb-r8a779a0",
-				     "renesas,etheravb-rcar-gen3";
+				     "renesas,etheravb-rcar-gen4";
 			reg = <0 0xe6840000 0 0x1000>;
 			interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>,
 					<GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>,
@@ -896,7 +896,7 @@
 
 		avb5: ethernet@e6850000 {
 			compatible = "renesas,etheravb-r8a779a0",
-				     "renesas,etheravb-rcar-gen3";
+				     "renesas,etheravb-rcar-gen4";
 			reg = <0 0xe6850000 0 0x1000>;
 			interrupts = <GIC_SPI 381 IRQ_TYPE_LEVEL_HIGH>,
 					<GIC_SPI 382 IRQ_TYPE_LEVEL_HIGH>,
@@ -1019,7 +1019,7 @@
 
 		msiof0: spi@e6e90000 {
 			compatible = "renesas,msiof-r8a779a0",
-				     "renesas,rcar-gen3-msiof";
+				     "renesas,rcar-gen4-msiof";
 			reg = <0 0xe6e90000 0 0x0064>;
 			interrupts = <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 618>;
@@ -1034,7 +1034,7 @@
 
 		msiof1: spi@e6ea0000 {
 			compatible = "renesas,msiof-r8a779a0",
-				     "renesas,rcar-gen3-msiof";
+				     "renesas,rcar-gen4-msiof";
 			reg = <0 0xe6ea0000 0 0x0064>;
 			interrupts = <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 619>;
@@ -1049,7 +1049,7 @@
 
 		msiof2: spi@e6c00000 {
 			compatible = "renesas,msiof-r8a779a0",
-				     "renesas,rcar-gen3-msiof";
+				     "renesas,rcar-gen4-msiof";
 			reg = <0 0xe6c00000 0 0x0064>;
 			interrupts = <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 620>;
@@ -1064,7 +1064,7 @@
 
 		msiof3: spi@e6c10000 {
 			compatible = "renesas,msiof-r8a779a0",
-				     "renesas,rcar-gen3-msiof";
+				     "renesas,rcar-gen4-msiof";
 			reg = <0 0xe6c10000 0 0x0064>;
 			interrupts = <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 621>;
@@ -1079,7 +1079,7 @@
 
 		msiof4: spi@e6c20000 {
 			compatible = "renesas,msiof-r8a779a0",
-				     "renesas,rcar-gen3-msiof";
+				     "renesas,rcar-gen4-msiof";
 			reg = <0 0xe6c20000 0 0x0064>;
 			interrupts = <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 622>;
@@ -1094,7 +1094,7 @@
 
 		msiof5: spi@e6c28000 {
 			compatible = "renesas,msiof-r8a779a0",
-				     "renesas,rcar-gen3-msiof";
+				     "renesas,rcar-gen4-msiof";
 			reg = <0 0xe6c28000 0 0x0064>;
 			interrupts = <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 623>;

arch/arm64/boot/dts/renesas/r8a779g0.dtsi

@@ -337,7 +337,7 @@
 		avb0: ethernet@e6800000 {
 			compatible = "renesas,etheravb-r8a779g0",
 				     "renesas,etheravb-rcar-gen4";
-			reg = <0 0xe6800000 0 0x800>;
+			reg = <0 0xe6800000 0 0x1000>;
 			interrupts = <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
@@ -384,7 +384,7 @@
 		avb1: ethernet@e6810000 {
 			compatible = "renesas,etheravb-r8a779g0",
 				     "renesas,etheravb-rcar-gen4";
-			reg = <0 0xe6810000 0 0x800>;
+			reg = <0 0xe6810000 0 0x1000>;
 			interrupts = <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 361 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 362 IRQ_TYPE_LEVEL_HIGH>,

arch/arm64/boot/dts/renesas/r9a07g043.dtsi

@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
 /*
- * Device Tree Source for the RZ/G2UL SoC
+ * Device Tree Source for the RZ/Five and RZ/G2UL SoCs
  *
  * Copyright (C) 2022 Renesas Electronics Corp.
  */
@@ -68,36 +68,8 @@
 		};
 	};
 
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		cpu0: cpu@0 {
-			compatible = "arm,cortex-a55";
-			reg = <0>;
-			device_type = "cpu";
-			#cooling-cells = <2>;
-			next-level-cache = <&L3_CA55>;
-			enable-method = "psci";
-			clocks = <&cpg CPG_CORE R9A07G043_CLK_I>;
-			operating-points-v2 = <&cluster0_opp>;
-		};
-
-		L3_CA55: cache-controller-0 {
-			compatible = "cache";
-			cache-unified;
-			cache-size = <0x40000>;
-		};
-	};
-
-	psci {
-		compatible = "arm,psci-1.0", "arm,psci-0.2";
-		method = "smc";
-	};
-
 	soc: soc {
 		compatible = "simple-bus";
-		interrupt-parent = <&gic>;
 		#address-cells = <2>;
 		#size-cells = <2>;
 		ranges;
@@ -545,12 +517,6 @@
 		sysc: system-controller@11020000 {
 			compatible = "renesas,r9a07g043-sysc";
 			reg = <0 0x11020000 0 0x10000>;
-			interrupts = <SOC_PERIPHERAL_IRQ(42) IRQ_TYPE_LEVEL_HIGH>,
-				     <SOC_PERIPHERAL_IRQ(43) IRQ_TYPE_LEVEL_HIGH>,
-				     <SOC_PERIPHERAL_IRQ(44) IRQ_TYPE_LEVEL_HIGH>,
-				     <SOC_PERIPHERAL_IRQ(45) IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "lpm_int", "ca55stbydone_int",
-					  "cm33stbyr_int", "ca55_deny";
 			status = "disabled";
 		};
 
@@ -603,16 +569,6 @@
 			dma-channels = <16>;
 		};
 
-		gic: interrupt-controller@11900000 {
-			compatible = "arm,gic-v3";
-			#interrupt-cells = <3>;
-			#address-cells = <0>;
-			interrupt-controller;
-			reg = <0x0 0x11900000 0 0x40000>,
-			      <0x0 0x11940000 0 0x60000>;
-			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_LOW>;
-		};
-
 		sdhi0: mmc@11c00000 {
 			compatible = "renesas,sdhi-r9a07g043",
 				     "renesas,rcar-gen3-sdhi";
@@ -893,12 +849,4 @@
 			};
 		};
 	};
-
-	timer {
-		compatible = "arm,armv8-timer";
-		interrupts-extended = <&gic GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
-				      <&gic GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
-				      <&gic GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
-				      <&gic GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
-	};
 };

arch/arm64/boot/dts/renesas/r9a07g043u.dtsi

@@ -10,3 +10,139 @@
 #define SOC_PERIPHERAL_IRQ(nr)		GIC_SPI nr
 
 #include "r9a07g043.dtsi"
+
+/ {
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a55";
+			reg = <0>;
+			device_type = "cpu";
+			#cooling-cells = <2>;
+			next-level-cache = <&L3_CA55>;
+			enable-method = "psci";
+			clocks = <&cpg CPG_CORE R9A07G043_CLK_I>;
+			operating-points-v2 = <&cluster0_opp>;
+		};
+
+		L3_CA55: cache-controller-0 {
+			compatible = "cache";
+			cache-unified;
+			cache-size = <0x40000>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-1.0", "arm,psci-0.2";
+		method = "smc";
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts-extended = <&gic GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+};
+
+&soc {
+	interrupt-parent = <&gic>;
+
+	irqc: interrupt-controller@110a0000 {
+		compatible = "renesas,r9a07g043u-irqc",
+			     "renesas,rzg2l-irqc";
+		reg = <0 0x110a0000 0 0x10000>;
+		#interrupt-cells = <2>;
+		#address-cells = <0>;
+		interrupt-controller;
+		interrupts = <SOC_PERIPHERAL_IRQ(0) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(1) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(2) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(3) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(4) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(5) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(6) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(7) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(8) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(444) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(445) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(446) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(447) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(448) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(449) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(450) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(451) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(452) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(453) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(454) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(455) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(456) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(457) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(458) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(459) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(460) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(461) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(462) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(463) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(464) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(465) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(466) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(467) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(468) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(469) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(470) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(471) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(472) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(473) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(474) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(475) IRQ_TYPE_LEVEL_HIGH>,
+			     <SOC_PERIPHERAL_IRQ(25) IRQ_TYPE_EDGE_RISING>,
+			     <SOC_PERIPHERAL_IRQ(34) IRQ_TYPE_EDGE_RISING>,
+			     <SOC_PERIPHERAL_IRQ(35) IRQ_TYPE_EDGE_RISING>,
+			     <SOC_PERIPHERAL_IRQ(36) IRQ_TYPE_EDGE_RISING>,
+			     <SOC_PERIPHERAL_IRQ(37) IRQ_TYPE_EDGE_RISING>,
+			     <SOC_PERIPHERAL_IRQ(38) IRQ_TYPE_EDGE_RISING>,
+			     <SOC_PERIPHERAL_IRQ(39) IRQ_TYPE_EDGE_RISING>;
+		interrupt-names = "nmi",
+				  "irq0", "irq1", "irq2", "irq3",
+				  "irq4", "irq5", "irq6", "irq7",
+				  "tint0", "tint1", "tint2", "tint3",
+				  "tint4", "tint5", "tint6", "tint7",
+				  "tint8", "tint9", "tint10", "tint11",
+				  "tint12", "tint13", "tint14", "tint15",
+				  "tint16", "tint17", "tint18", "tint19",
+				  "tint20", "tint21", "tint22", "tint23",
+				  "tint24", "tint25", "tint26", "tint27",
+				  "tint28", "tint29", "tint30", "tint31",
+				  "bus-err", "ec7tie1-0", "ec7tie2-0",
+				  "ec7tiovf-0", "ec7tie1-1", "ec7tie2-1",
+				  "ec7tiovf-1";
+		clocks = <&cpg CPG_MOD R9A07G043_IA55_CLK>,
+			<&cpg CPG_MOD R9A07G043_IA55_PCLK>;
+		clock-names = "clk", "pclk";
+		power-domains = <&cpg>;
+		resets = <&cpg R9A07G043_IA55_RESETN>;
+	};
+
+	gic: interrupt-controller@11900000 {
+		compatible = "arm,gic-v3";
+		#interrupt-cells = <3>;
+		#address-cells = <0>;
+		interrupt-controller;
+		reg = <0x0 0x11900000 0 0x40000>,
+		      <0x0 0x11940000 0 0x60000>;
+		interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&sysc {
+	interrupts = <SOC_PERIPHERAL_IRQ(42) IRQ_TYPE_LEVEL_HIGH>,
+		     <SOC_PERIPHERAL_IRQ(43) IRQ_TYPE_LEVEL_HIGH>,
+		     <SOC_PERIPHERAL_IRQ(44) IRQ_TYPE_LEVEL_HIGH>,
+		     <SOC_PERIPHERAL_IRQ(45) IRQ_TYPE_LEVEL_HIGH>;
+	interrupt-names = "lpm_int", "ca55stbydone_int",
+			  "cm33stbyr_int", "ca55_deny";
+};

arch/arm64/boot/dts/renesas/r9a07g044.dtsi

@@ -698,7 +698,27 @@
 				     <GIC_SPI 472 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 473 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 474 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 475 IRQ_TYPE_LEVEL_HIGH>;
+				     <GIC_SPI 475 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 25 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 34 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 35 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 36 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 37 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 38 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 39 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "nmi", "irq0", "irq1", "irq2", "irq3",
+					  "irq4", "irq5", "irq6", "irq7",
+					  "tint0", "tint1", "tint2", "tint3",
+					  "tint4", "tint5", "tint6", "tint7",
+					  "tint8", "tint9", "tint10", "tint11",
+					  "tint12", "tint13", "tint14", "tint15",
+					  "tint16", "tint17", "tint18", "tint19",
+					  "tint20", "tint21", "tint22", "tint23",
+					  "tint24", "tint25", "tint26", "tint27",
+					  "tint28", "tint29", "tint30", "tint31",
+					  "bus-err", "ec7tie1-0", "ec7tie2-0",
+					  "ec7tiovf-0", "ec7tie1-1", "ec7tie2-1",
+					  "ec7tiovf-1";
 			clocks = <&cpg CPG_MOD R9A07G044_IA55_CLK>,
 				 <&cpg CPG_MOD R9A07G044_IA55_PCLK>;
 			clock-names = "clk", "pclk";

arch/arm64/boot/dts/renesas/r9a07g054.dtsi

@@ -704,7 +704,27 @@
 				     <GIC_SPI 472 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 473 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 474 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 475 IRQ_TYPE_LEVEL_HIGH>;
+				     <GIC_SPI 475 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 25 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 34 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 35 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 36 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 37 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 38 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 39 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "nmi", "irq0", "irq1", "irq2", "irq3",
+					  "irq4", "irq5", "irq6", "irq7",
+					  "tint0", "tint1", "tint2", "tint3",
+					  "tint4", "tint5", "tint6", "tint7",
+					  "tint8", "tint9", "tint10", "tint11",
+					  "tint12", "tint13", "tint14", "tint15",
+					  "tint16", "tint17", "tint18", "tint19",
+					  "tint20", "tint21", "tint22", "tint23",
+					  "tint24", "tint25", "tint26", "tint27",
+					  "tint28", "tint29", "tint30", "tint31",
+					  "bus-err", "ec7tie1-0", "ec7tie2-0",
+					  "ec7tiovf-0", "ec7tie1-1", "ec7tie2-1",
+					  "ec7tiovf-1";
 			clocks = <&cpg CPG_MOD R9A07G054_IA55_CLK>,
 				 <&cpg CPG_MOD R9A07G054_IA55_PCLK>;
 			clock-names = "clk", "pclk";

arch/arm64/boot/dts/renesas/ulcb-kf.dtsi

@@ -251,6 +251,7 @@
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
+		#interrupt-cells = <2>;
 		interrupt-parent = <&gpio6>;
 		interrupts = <8 IRQ_TYPE_EDGE_FALLING>;
 
@@ -311,6 +312,7 @@
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
+		#interrupt-cells = <2>;
 		interrupt-parent = <&gpio6>;
 		interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
 	};
@@ -331,6 +333,7 @@
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
+		#interrupt-cells = <2>;
 		interrupt-parent = <&gpio7>;
 		interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
 	};
@@ -341,6 +344,7 @@
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
+		#interrupt-cells = <2>;
 		interrupt-parent = <&gpio5>;
 		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
 	};

arch/arm64/boot/dts/rockchip/px30.dtsi

@@ -607,6 +607,7 @@
 		clock-names = "spiclk", "apb_pclk";
 		dmas = <&dmac 12>, <&dmac 13>;
 		dma-names = "tx", "rx";
+		num-cs = <2>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&spi0_clk &spi0_csn &spi0_miso &spi0_mosi>;
 		#address-cells = <1>;
@@ -622,6 +623,7 @@
 		clock-names = "spiclk", "apb_pclk";
 		dmas = <&dmac 14>, <&dmac 15>;
 		dma-names = "tx", "rx";
+		num-cs = <2>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&spi1_clk &spi1_csn0 &spi1_csn1 &spi1_miso &spi1_mosi>;
 		#address-cells = <1>;

arch/arm64/boot/dts/rockchip/rk3328.dtsi

@@ -741,11 +741,20 @@
 		status = "disabled";
 
 		ports {
-			hdmi_in: port {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			hdmi_in: port@0 {
+				reg = <0>;
+
 				hdmi_in_vop: endpoint {
 					remote-endpoint = <&vop_out_hdmi>;
 				};
 			};
+
+			hdmi_out: port@1 {
+				reg = <1>;
+			};
 		};
 	};