[ Upstream commit 3d3e88e336 ]
In sdw_prep_deprep_slave_ports(), after the wait_for_completion()
the DP prepare status register is read. If this indicates that the
port is now prepared, the code should continue with the port setup.
It is irrelevant whether the wait_for_completion() timed out if the
port is now ready.
The previous implementation would always fail if the
wait_for_completion() timed out, even if the port was reporting
successful prepare.
This patch also fixes a minor bug where the return from sdw_read()
was not checked for error - any error code with LSBits clear could
be misinterpreted as a successful port prepare.
Fixes: 79df15b7d3 ("soundwire: Add helpers for ports operations")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210618144745.30629-1-rf@opensource.cirrus.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 973794e856 ]
Intel stress-tests routinely report IO timeouts and invalid power
management transitions. Upon further analysis, we seem to be using the
wrong devices in pm_runtime calls.
Before reading and writing registers, we first need to make sure the
Slave is fully resumed. The existing code attempts to do such that,
however because of a confusion dating from 2017 and copy/paste, we
end-up resuming the parent only instead of resuming the codec device.
This can lead to accesses to the Slave registers while the bus is
still being configured and the Slave not enumerated, and as a result
IO errors occur.
This is a classic problem, similar confusions happened for HDaudio
between bus and codec device, leading to power management issues.
Fix by using the relevant device for all uses of pm_runtime functions.
Fixes: 60ee9be255 ('soundwire: bus: add PM/no-PM versions of read/write functions')
Fixes: aa79293517 ('soundwire: bus: fix io error when processing alert event')
Fixes: 9d715fa005 ('soundwire: Add IO transfer')
Reported-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210122070634.12825-9-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db9d9f944f ]
The existing code reports a NAK only when ACK=0
This is not aligned with the SoundWire 1.x specifications.
Table 32 in the SoundWire 1.2 specification shows that a Device shall
not set NAK=1 if ACK=1. But Table 33 shows the Combined Response
may very well be NAK=1/ACK=1, e.g. if another Device than the one
addressed reports a parity error.
NAK=1 signals a 'Command_Aborted', regardless of the ACK bit value.
Move the tests for NAK so that the NAK=1/ACK=1 combination is properly
detected according to the specification.
Fixes: 956baa1992 ('soundwire: cdns: Add sdw_master_ops and IO transfer support')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210115053738.22630-5-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e04e60fce4 ]
The 'master' device acts as a glue layer used during bus
initialization only, and it needs to be 'transparent' for pm_runtime
management. Its behavior should be that it becomes active when one of
its children becomes active, and suspends when all of its children are
suspended.
In our tests on Intel platforms, we routinely see these sort of
warnings on the initial boot:
[ 21.447345] rt715 sdw:3:25d:715:0: runtime PM trying to activate
child device sdw:3:25d:715:0 but parent (sdw-master-3) is not active
This is root-caused to a missing setup to make the device 'active' on
probe. Since we don't want the device to remain active forever after
the probe, the autosuspend configuration is also enabled at the end of
the probe - the device will actually autosuspend only in the case
where there are no devices physically attached. In practice, the
master device will suspend when all its children are no longer active.
Fixes: bd84256e86 ('soundwire: master: enable pm runtime')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20201124130742.10986-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47edc0104c ]
Commit 5bd773242f ("soundwire: qcom: avoid dependency on
CONFIG_SLIMBUS") removed hard dependency on Slimbus for qcom driver but
it results in build failure when: CONFIG_SOUNDWIRE_QCOM=y
CONFIG_SLIMBUS=m
drivers/soundwire/qcom.o: In function `qcom_swrm_probe':
qcom.c:(.text+0xf44): undefined reference to `slimbus_bus'
Fix this by using IS_REACHABLE() in driver which is recommended to be
used with imply.
Fixes: 5bd773242f ("soundwire: qcom: avoid dependency on CONFIG_SLIMBUS")
Reported-by: kernel test robot <lkp@intel.com>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Link: https://lore.kernel.org/r/20201125055155.GD8403@vkoul-mobl
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Vinod writes:
soundwire updates for 5.10-rc1
This round of update includes:
- Generic bandwidth allocation algorithm from Intel folks
- PM support for Intel chipsets
- Updates to Intel drivers which makes sdw usable on latest laptops
- Support for MMIO SDW controllers found in QC chipsets
- Update to subsystem to use helpers in bitfield.h to manage register
bits
* tag 'soundwire-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire: (66 commits)
soundwire: sysfs: add slave status and device number before probe
soundwire: bus: add enumerated Slave device to device list
soundwire: remove an unnecessary NULL check
soundwire: cadence: add data port test fail interrupt
soundwire: intel: enable test modes
soundwire: enable Data Port test modes
soundwire: intel: use {u32|u16}p_replace_bits
soundwire: cadence: use u32p_replace_bits
soundwire: qcom: get max rows and cols info from compatible
soundwire: qcom: add support to block packing mode
soundwire: qcom: clear BIT FIELDs before value set.
soundwire: Add generic bandwidth allocation algorithm
soundwire: cadence: add parity error injection through debugfs
soundwire: bus: export broadcast read/write capability for tests
ASoC: codecs: realtek-soundwire: ignore initial PARITY errors
soundwire: bus: use quirk to filter out invalid parity errors
soundwire: slave: add first_interrupt_done status
soundwire: bus: filter-out unwanted interrupt reports
ASoC/soundwire: bus: use property to set interrupt masks
soundwire: qcom: fix SLIBMUS/SLIMBUS typo
...
The MIPI DisCo device properties that are read by the driver from
platform firmware, or hard-coded in the driver, should only be
provided as sysfs entries when a driver probes successfully.
However the device status and device number is updated even when there
is no driver present, and hence can be updated when a Slave device is
detected on the bus without being described in platform firmware and
without any driver registered/probed.
As suggested by GregKH, the attribute group for Slave status and
device number is is added by default upon device registration.
Credits to Vinod Koul for the status_show() function, shared in a
separate patch and used as is here. The status table was modified to
remove an unnecessary enum and status_show() is handled in a different
group attribute than what was suggested by Vinod.
Tested-by: Srinivas Kandgatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Co-developed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200924194430.121058-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Currently Slave devices are only added on startup, either from Device
Tree or ACPI entries. However Slave devices that are physically
present on the bus, but not described in platform firmware, will never
be added to the device list. The user/integrator can only know the
list of devices by looking a dynamic debug logs.
This patch suggests adding a Slave device even if there is no matching
DT or ACPI entry, so that we can see this in sysfs entry.
Initial code from Srinivas. Comments, fixes for ACPI probe and edits
of commit message by Pierre.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200924194430.121058-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
According to usage (bitfields.h) of REG_FIELDS,
Modify is:
reg &= ~REG_FIELD_C;
reg |= FIELD_PREP(REG_FIELD_C, c);
Patch ("soundwire: qcom : use FIELD_{GET|PREP}") seems to have
accidentally removed clearing bit field while modifying the register.
Fix this by using u32p_replace_bits() to clear and set the values.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200917120138.11313-2-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This algorithm computes bus parameters like clock frequency, frame
shape and port transport parameters based on active stream(s) running
on the bus.
Developers can also implement their own .compute_params() callback for
specific resource management algorithm, and set if before calling
sdw_add_bus_master()
Credits: this patch is based on an earlier internal contribution by
Vinod Koul, Sanyog Kale, Shreyas Nc and Hardik Shah. All hard-coded
values were removed from the initial contribution to use BIOS
information instead.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20200908131520.5712-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Cadence IP can inject errors, let's make use of this capability to
test Slave parity error checks.
See e.g. example log where both the master and slave detect the parity
error injected on a dummy read command.
cd /sys/kernel/debug/soundwire/master-1/intel-sdw/
echo 1 > cdns-parity-error-injection
[ 44.756249] intel-master sdw-master-1: Parity error
[ 44.756313] intel-master sdw-master-1: Msg NACK received
[ 44.756366] intel-master sdw-master-1: Msg NACKed for Slave 15
[ 44.756375] intel-master sdw-master-1: trf on Slave 15 failed:-5
[ 44.756382] intel-master sdw-master-1: parity error injection, read: -5
[ 44.756649] rt1308 sdw:1:25d:1308:0: Parity error detected
The code makes sure the Master device is resumed, hence the clock
restarted, before sending a parity error.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20200908134521.6781-8-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Unlike the traditional usage, in the SoundWire specification the
interrupt masks only gate the propagation of an interrupt condition to
the PING frame status. They do not gate the changes of the INT_STAT
registers, which will happen regardless of the mask settings. See
Figure 116 of the SoundWire 1.2 specification for an in-depth
description of the interrupt model.
When the bus driver reads the SCP_INT1_STAT register, it will retrieve
all the interrupt status, including for the mask fields that were not
explicitly set. For example, even if the PARITY mask is not set, the
PARITY error status will be reported if an implementation-defined
interrupt for jack detection is enabled and occurs.
Filtering undesired interrupt reports and handling has to be
implemented in software. This patch enables this filtering for the
INT1_IMPL_DEF, PARITY and BUS_CLASH interrupt sources.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20200908134521.6781-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In system suspend stress cases, the SOF CI reports timeouts. The root
cause is that an alert is generated while the system suspends. The
interrupt handling generates transactions on the bus that will never
be handled because the interrupts are disabled in parallel.
As a result, the transaction never completes and times out on resume.
This error doesn't seem too problematic since it happens in a work
queue, and the system recovers without issues.
Nevertheless, this race condition should not happen. When doing a
system suspend, or when disabling interrupts, we should make sure the
current transaction can complete, and prevent new work from being
queued.
BugLink: https://github.com/thesofproject/linux/issues/2344
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20200817222340.18042-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
