PLL_AUDIO has a ternary divider (a copy of the secondary divider) and
PLL_VIDEO has a primary phased output.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
RP1 contains various PLLs and clocks for driving the hardware
blocks, so add a driver to configure these.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Add the bare minimum needed to boot BCM2708 from a Device Tree.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
BCM2708: DT: change 'axi' nodename to 'soc'
Change DT node named 'axi' to 'soc' so it matches ARCH_BCM2835.
The VC4 bootloader fills in certain properties in the 'axi' subtree,
but since this is part of an upstreaming effort, the name is changed.
Signed-off-by: Noralf Tronnes notro@tronnes.org
BCM2708_DT: Correct length of the peripheral space
Use dts-dirs feature for overlays.
The kernel makefiles have a dts-dirs target that is for vendor subdirectories.
Using this fixes the install_dtbs target, which previously did not install the overlays.
BCM270X_DT: configure I2S DMA channels
Signed-off-by: Matthias Reichl <hias@horus.com>
BCM270X_DT: switch to bcm2835-i2s
I2S soundcard drivers with proper devicetree support (i.e. not linking
to the cpu_dai/platform via name but to cpu/platform via of_node)
will work out of the box without any modifications.
When the kernel is compiled without devicetree support the platform
code will instantiate the bcm2708-i2s driver and I2S soundcard drivers
will link to it via name, as before.
Signed-off-by: Matthias Reichl <hias@horus.com>
SDIO-overlay: add poll_once-boolean parameter
Add paramter to toggle sdio-device-polling
done every second or once at boot-time.
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
BCM270X_DT: Make mmc overlay compatible with current firmware
The original DT overlay logic followed a merge-then-patch procedure,
i.e. parameters are applied to the loaded overlay before the overlay
is merged into the base DTB. This sequence has been changed to
patch-then-merge, in order to support parameterised node names, and
to protect against bad overlays. As a result, overrides (parameters)
must only target labels in the overlay, but the overlay can obviously target nodes in the base DTB.
mmc-overlay.dts (that switches back to the original mmc sdcard
driver) is the only overlay violating that rule, and this patch
fixes it.
bcm270x_dt: Use the sdhost MMC controller by default
The "mmc" overlay reverts to using the other controller.
squash: Add cprman to dt
BCM270X_DT: Use clk_core for I2C interfaces
BCM270X_DT: Use bcm283x.dtsi, bcm2835.dtsi and bcm2836.dtsi
The mainline Device Tree files are quite close to downstream now.
Let's use bcm283x.dtsi, bcm2835.dtsi and bcm2836.dtsi as base files
for our dts files.
Mainline dts files are based on these files:
bcm2835-rpi.dtsi
bcm2835.dtsi bcm2836.dtsi
bcm283x.dtsi
Current downstream are based on these:
bcm2708.dtsi bcm2709.dtsi bcm2710.dtsi
bcm2708_common.dtsi
This patch introduces this dependency:
bcm2708.dtsi bcm2709.dtsi
bcm2708-rpi.dtsi
bcm270x.dtsi
bcm2835.dtsi bcm2836.dtsi
bcm283x.dtsi
And:
bcm2710.dtsi
bcm2708-rpi.dtsi
bcm270x.dtsi
bcm283x.dtsi
bcm270x.dtsi contains the downstream bcm283x.dtsi diff.
bcm2708-rpi.dtsi is the downstream version of bcm2835-rpi.dtsi.
Other changes:
- The led node has moved from /soc/leds to /leds. This is not a problem
since the label is used to reference it.
- The clk_osc reg property changes from 6 to 3.
- The gpu nodes has their interrupt property set in the base file.
- the clocks label does not point to the /clocks node anymore, but
points to the cprman node. This is not a problem since the overlays
that use the clock node refer to it directly: target-path = "/clocks";
- some nodes now have 2 labels since mainline and downstream differs in
this respect: cprman/clocks, spi0/spi, gpu/vc4.
- some nodes doesn't have an explicit status = "okay" since they're not
disabled in the base file: watchdog and random.
- gpiomem doesn't need an explicit status = "okay".
- bcm2708-rpi-cm.dts got the hpd-gpios property from bcm2708_common.dtsi,
it's now set directly in that file.
- bcm2709-rpi-2-b.dts has the timer node moved from /soc/timer to /timer.
- Removed clock-frequency property on the bcm{2709,2710}.dtsi timer nodes.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270X_DT: Use raspberrypi-power to turn on USB power
Use the raspberrypi-power driver to turn on USB power.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270X_DT: Add a .dtbo target, use for overlays
Change the filenames and extensions to keep the pre-DDT style of
overlay (<name>-overlay.dtb) distinct from new ones that use a
different style of local fixups (<name>.dtbo), and to match other
platforms.
The RPi firmware uses the DDTK trailer atom to choose which type of
overlay to use for each kernel.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Don't generate "linux,phandle" props
The EPAPR standard says to use "phandle" properties to store phandles,
rather than the deprecated "linux,phandle" version. By default, dtc
generates both, but adding "-H epapr" causes it to only generate
"phandle"s, saving some space and clutter.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Add overlay for enc28j60 on SPI2
Works on SPI2 for compute module
BCM270X_DT: Add midi-uart0 overlay
MIDI requires 31.25kbaud, a baudrate unsupported by Linux. The
midi-uart0 overlay configures uart0 (ttyAMA0) to use a fake clock
so that requesting 38.4kbaud actually gets 31.25kbaud.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Add i2c-sensor overlay
The i2c-sensor overlay is a container for various pressure and
temperature sensors, currently bmp085 and bmp280. The standalone
bmp085_i2c-sensor overlay is now deprecated.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: overlays/*-overlay.dtb -> overlays/*.dtbo (#1752)
We now create overlays as .dtbo files.
build: support for .dtbo files for dtb overlays
Kernel 4.4.6+ on RaspberryPi support .dtbo files for overlays, instead of .dtb.
Patch the kernel, which has faulty rules to generate .dtbo the way yocto does
Signed-off-by: Herve Jourdain <herve.jourdain@neuf.fr>
Signed-off-by: Khem Raj <raj.khem@gmail.com>
BCM270X: Drop position requirement for CMA in VC4 overlay.
No longer necessary since 2aefcd5761,
and will probably let peeople that want to choose a larger CMA
allocation (particularly on pi0/1).
Signed-off-by: Eric Anholt <eric@anholt.net>
BCM270X_DT: RPi Device Tree tidy
Use the upstream sdhost node, add thermal-zones, and factor out some
common elements.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
kbuild: Silence unhelpful DTC warnings
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: DT build rules no longer arch-specific
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Pull iommu updates from Joerg Roedel:
"Core changes:
- Consolidate probe_device path
- Make the PCI-SAC IOVA allocation trick PCI-only
AMD IOMMU:
- Consolidate PPR log handling
- Interrupt handling improvements
- Refcount fixes for amd_iommu_v2 driver
Intel VT-d driver:
- Enable idxd device DMA with pasid through iommu dma ops
- Lift RESV_DIRECT check from VT-d driver to core
- Miscellaneous cleanups and fixes
ARM-SMMU drivers:
- Device-tree binding updates:
- Add additional compatible strings for Qualcomm SoCs
- Allow ASIDs to be configured in the DT to work around Qualcomm's
broken hypervisor
- Fix clocks for Qualcomm's MSM8998 SoC
- SMMUv2:
- Support for Qualcomm's legacy firmware implementation featured
on at least MSM8956 and MSM8976
- Match compatible strings for Qualcomm SM6350 and SM6375 SoC
variants
- SMMUv3:
- Use 'ida' instead of a bitmap for VMID allocation
- Rockchip IOMMU:
- Lift page-table allocation restrictions on newer hardware
- Mediatek IOMMU:
- Add MT8188 IOMMU Support
- Renesas IOMMU:
- Allow PCIe devices
.. and the usual set of cleanups an smaller fixes"
* tag 'iommu-updates-v6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (64 commits)
iommu: Explicitly include correct DT includes
iommu/amd: Remove unused declarations
iommu/arm-smmu-qcom: Add SM6375 SMMUv2
iommu/arm-smmu-qcom: Add SM6350 DPU compatible
iommu/arm-smmu-qcom: Add SM6375 DPU compatible
iommu/arm-smmu-qcom: Sort the compatible list alphabetically
dt-bindings: arm-smmu: Fix MSM8998 clocks description
iommu/vt-d: Remove unused extern declaration dmar_parse_dev_scope()
iommu/vt-d: Fix to convert mm pfn to dma pfn
iommu/vt-d: Fix to flush cache of PASID directory table
iommu/vt-d: Remove rmrr check in domain attaching device path
iommu: Prevent RESV_DIRECT devices from blocking domains
dmaengine/idxd: Re-enable kernel workqueue under DMA API
iommu/vt-d: Add set_dev_pasid callback for dma domain
iommu/vt-d: Prepare for set_dev_pasid callback
iommu/vt-d: Make prq draining code generic
iommu/vt-d: Remove pasid_mutex
iommu/vt-d: Add domain_flush_pasid_iotlb()
iommu: Move global PASID allocation from SVA to core
iommu: Generalize PASID 0 for normal DMA w/o PASID
...
Pull char/misc driver updates from Greg KH:
"Here is the big set of char/misc and other small driver subsystem
changes for 6.6-rc1.
Stuff all over the place here, lots of driver updates and changes and
new additions. Short summary is:
- new IIO drivers and updates
- Interconnect driver updates
- fpga driver updates and additions
- fsi driver updates
- mei driver updates
- coresight driver updates
- nvmem driver updates
- counter driver updates
- lots of smaller misc and char driver updates and additions
All of these have been in linux-next for a long time with no reported
problems"
* tag 'char-misc-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (267 commits)
nvmem: core: Notify when a new layout is registered
nvmem: core: Do not open-code existing functions
nvmem: core: Return NULL when no nvmem layout is found
nvmem: core: Create all cells before adding the nvmem device
nvmem: u-boot-env:: Replace zero-length array with DECLARE_FLEX_ARRAY() helper
nvmem: sec-qfprom: Add Qualcomm secure QFPROM support
dt-bindings: nvmem: sec-qfprom: Add bindings for secure qfprom
dt-bindings: nvmem: Add compatible for QCM2290
nvmem: Kconfig: Fix typo "drive" -> "driver"
nvmem: Explicitly include correct DT includes
nvmem: add new NXP QorIQ eFuse driver
dt-bindings: nvmem: Add t1023-sfp efuse support
dt-bindings: nvmem: qfprom: Add compatible for MSM8226
nvmem: uniphier: Use devm_platform_get_and_ioremap_resource()
nvmem: qfprom: do some cleanup
nvmem: stm32-romem: Use devm_platform_get_and_ioremap_resource()
nvmem: rockchip-efuse: Use devm_platform_get_and_ioremap_resource()
nvmem: meson-mx-efuse: Convert to devm_platform_ioremap_resource()
nvmem: lpc18xx_otp: Convert to devm_platform_ioremap_resource()
nvmem: brcm_nvram: Use devm_platform_get_and_ioremap_resource()
...
Pull clk subsystem updates from Stephen Boyd:
"This pull request is full of clk driver changes. In fact, there aren't
any changes to the clk framework this time around. That's probably
because everyone was on vacation (yours truly included). We did lose a
couple clk drivers this time around because nobody was using those
devices. That skews the diffstat a bit, but either way, nothing looks
out of the ordinary here. The usual suspects are chugging along adding
support for more SoCs and fixing bugs.
If I had to choose, I'd say the theme for the past few months has been
"polish". There's quite a few patches that migrate to
devm_platform_ioremap_resource() in here. And there's more than a
handful of patches that move the NR_CLKS define from the DT binding
header to the driver. There's even patches that migrate drivers to use
clk_parent_data and clk_hw to describe clk tree topology. It seems
that the spring (summer?) cleaning bug got some folks, or the
semiconductor shortage finally hit the software side.
New Drivers:
- StarFive JH7110 SoC clock drivers
- Qualcomm IPQ5018 Global Clock Controller driver
- Versa3 clk generator to support 48KHz playback/record with audio
codec on RZ/G2L SMARC EVK
Removed Drivers:
- Remove non-OF mmp clk drivers
- Remove OXNAS clk driver
Updates:
- Add __counted_by to struct clk_hw_onecell_data and struct
spmi_pmic_div_clk_cc
- Move defines for numbers of clks (NR_CLKS) from DT headers to
drivers
- Introduce kstrdup_and_replace() and use it
- Add PLL rates for Rockchip rk3568
- Add the display clock tree for Rockchip rv1126
- Add Audio Clock Generator (ADG) clocks on Renesas R-Car Gen3 and
RZ/G2 SoCs
- Convert sun9i-mmc clock to use
devm_platform_get_and_ioremap_resource()
- Fix function name in a comment in ccu_mmc_timing.c
- Parameter name correction for ccu_nkm_round_rate()
- Implement CLK_SET_RATE_PARENT for Allwinner NKM clocks, i.e.
consider alternative parent rates when determining clock rates
- Set CLK_SET_RATE_PARENT for Allwinner A64 pll-mipi
- Support finding closest (as opposed to closest but not higher)
clock rate for NM, NKM, mux and div type clocks, as use it for
Allwinner A64 pll-video0
- Prefer current parent rate if able to generate ideal clock rate for
Allwinner NKM clocks
- Clean up Qualcomm SMD RPM driver, with interconnect bus clocks
moved out to the interconnect drivers
- Fix various PM runtime bugs across many Qualcomm clk drivers
- Migrate Qualcomm MDM9615 is to parent_hw and parent_data
- Add network related resets on Qualcomm IPQ4019
- Add a couple missing USB related clocks to Qualcomm IPQ9574
- Add missing gpll0_sleep_clk_src to Qualcomm MSM8917 global clock
controller
- In the Qualcomm QDU1000 global clock controller, GDSCs, clkrefs,
and GPLL1 are added, while PCIe pipe clock, SDCC rcg ops are
corrected
- Add missing GDSCs to and correct GDSCs for the SC8280XP global
clock controller driver
- Support retention for the Qualcomm SC8280XP display clock
controller GDSCs.
- Qualcommm's SDCC apps_clk_src is marked with CLK_OPS_PARENT_ENABLE
to fix issues with missing parent clocks across sc7180, sm7150,
sm6350 and sm8250, while sm8450 is corrected to use floor ops
- Correct Qualcomm SM6350 GPU clock controller's clock supplies
- Drop unwanted clocks from the Qualcomm IPQ5332 GCC driver
- Add missing OXILICX GDSC to Qualcomm MSM8226 GCC
- Change the delay in the Qualcomm reset controller to fsleep() for
correctness
- Extend the Qualcomm SM83550 Video clock controller to support
SC8280XP
- Add graphics clock support on Renesas RZ/G2M, RZ/G2N, RZ/G2E, and
R-Car H3, M3-W, and M3-N SoCs
- Add Clocked Serial Interface (CSI) clocks on Renesas RZ/V2M
- Add PWM (MTU3) clock and reset on Renesas RZ/G2UL and RZ/Five
- Add the PDM IPC clock for i.MX93
- Add 519.75MHz frequency support for i.MX9 PLL
- Simplify the .determine_rate() implementation for i.MX GPR mux
- Make the i.MX8QXP LPCG clock use devm_platform_ioremap_resource()
- Add the audio mux clock to i.MX8
- Fix the SPLL2 MULT range for PLLv4
- Update the SPLL2 type in i.MX8ULP
- Fix the SAI4 clock on i.MX8MP
- Add silicon revision print for i.MX25 on clocks init
- Drop the return value from __mx25_clocks_init()
- Fix the clock pauses on no-op set_rate for i.MX8M composite clock
- Drop restrictions for i.MX PLL14xx and fix its max prediv value
- Drop the 393216000 and 361267200 from i.MX PLL14xx rate table to
allow glitch free switching"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (207 commits)
clk: qcom: Fix SM_GPUCC_8450 dependencies
clk: lmk04832: Support using PLL1_LD as SPI readback pin
clk: lmk04832: Don't disable vco clock on probe fail
clk: lmk04832: Set missing parent_names for output clocks
clk: mvebu: Convert to devm_platform_ioremap_resource()
clk: nuvoton: Convert to devm_platform_ioremap_resource()
clk: socfpga: agilex: Convert to devm_platform_ioremap_resource()
clk: ti: Use devm_platform_get_and_ioremap_resource()
clk: mediatek: Convert to devm_platform_ioremap_resource()
clk: hsdk-pll: Convert to devm_platform_ioremap_resource()
clk: gemini: Convert to devm_platform_ioremap_resource()
clk: fsl-sai: Convert to devm_platform_ioremap_resource()
clk: bm1880: Convert to devm_platform_ioremap_resource()
clk: axm5516: Convert to devm_platform_ioremap_resource()
clk: actions: Convert to devm_platform_ioremap_resource()
clk: cdce925: Remove redundant of_match_ptr()
clk: pxa910: Move number of clocks to driver source
clk: pxa1928: Move number of clocks to driver source
clk: pxa168: Move number of clocks to driver source
clk: mmp2: Move number of clocks to driver source
...
Pull pin control updates from Linus Walleij:
"We have some patches to DTS[I] files in arm and arm64 as well, that
were merged here as DT headers were being changed.
The most interesting stuff is the Intel Tangier chip support and
AMLogic C3 in my opinion.
No core changes this time.
Drivers:
- Intel Tangier SoC pin control support
- AMLogic C3 SoC pin control support
- Texas Instruments AM654 SoC pin control support
- Qualcomm SM8350 and SM6115 LPASS (Low Power Audio Sub-System) pin
control support
- Qualcomm PMX75 and PM7550BA (Power Management) pin control support
- Qualcomm PMC8180 and PMC8180C (Power Management) pin control
support
- DROP the Oxnas driver as there is not enough of community interest
to keep carrying this ARM(11) port
Enhancements:
- Bias control in the MT7986 pin control driver
- Misc device tree binding enhancements such as the Broadcom 11351
being converted to YAML
- New macro: DEFINE_NOIRQ_DEV_PM_OPS() put to use
- Clean up some SPDX headers
- Handle non-unique devicetree subnode names in two Renesas drivers"
* tag 'pinctrl-v6.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (80 commits)
pinctrl: mlxbf3: Remove gpio_disable_free()
pinctrl: use capital "OR" for multiple licenses in SPDX
dt-bindings: pinctrl: renesas,rza2: Use 'additionalProperties' for child nodes
pinctrl: cherryview: fix address_space_handler() argument
pinctrl: intel: consolidate ACPI dependency
pinctrl: tegra: Switch to use DEFINE_NOIRQ_DEV_PM_OPS() helper
pinctrl: renesas: Switch to use DEFINE_NOIRQ_DEV_PM_OPS() helper
pinctrl: mvebu: Switch to use DEFINE_NOIRQ_DEV_PM_OPS() helper
pinctrl: at91: Switch to use DEFINE_NOIRQ_DEV_PM_OPS() helper
pinctrl: cherryview: Switch to use DEFINE_NOIRQ_DEV_PM_OPS() helper
pm: Introduce DEFINE_NOIRQ_DEV_PM_OPS() helper
pinctrl: mediatek: assign functions to configure pin bias on MT7986
pinctrl: mediatek: fix pull_type data for MT7981
dt-bindings: pinctrl: aspeed: Allow only defined pin mux node properties
dt-bindings: pinctrl: Drop 'phandle' properties
pinctrl: lynxpoint: Make use of pm_ptr()
pinctrl: baytrail: Make use of pm_ptr()
pinctrl: intel: Switch to use exported namespace
pinctrl: lynxpoint: reuse common functions from pinctrl-intel
pinctrl: cherryview: reuse common functions from pinctrl-intel
...
Pull devicetree updates from Rob Herring:
"DT core:
- Add support for generating DT nodes for PCI devices. This is the
groundwork for applying overlays to PCI devices containing
non-discoverable downstream devices.
- DT unittest additions to check reverted changesets, to test for
refcount issues, and to test unresolved symbols. Also, various
clean-ups of the unittest along the way.
- Refactor node and property manipulation functions to better share
code with old API and changeset API
- Refactor changeset print functions to a common implementation
- Move some platform_device specific functions into of_platform.c
Bindings:
- Treewide fixing of typos
- Treewide clean-up of SPDX tags to use 'OR' consistently
- Last chunk of dropping unnecessary quotes. With that, the check for
unnecessary quotes is enabled in yamllint.
- Convert ftgmac100, zynqmp-genpd, pps-gpio, syna,rmi4, and qcom,ssbi
bindings to DT schema format
- Add Allwinner V3s xHCI USB, Saef SF-TC154B display, QCom SM8450
Inline Crypto Engine, QCom SM6115 UFS, QCom SDM670 PDC interrupt
controller, Arm 2022 Cortex cores, and QCom IPQ9574 Crypto bindings
- Fixes for Rockchip DWC PCI binding
- Ensure all properties are evaluated on USB connector schema
- Fix dt-check-compatible script to find of_device_id instances with
compiler annotations"
* tag 'devicetree-for-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (64 commits)
dt-bindings: usb: Add V3s compatible string for OHCI
dt-bindings: usb: Add V3s compatible string for EHCI
dt-bindings: display: panel: mipi-dbi-spi: add Saef SF-TC154B
dt-bindings: vendor-prefixes: document Saef Technology
dt-bindings: thermal: lmh: update maintainer address
of: unittest: Fix of_unittest_pci_node() kconfig dependencies
dt-bindings: crypto: ice: Document sm8450 inline crypto engine
dt-bindings: ufs: qcom: Add ICE to sm8450 example
dt-bindings: ufs: qcom: Add sm6115 binding
dt-bindings: ufs: qcom: Add reg-names property for ICE
dt-bindings: yamllint: Enable quoted string check
dt-bindings: Drop remaining unneeded quotes
of: unittest-data: Fix whitespace - angular brackets
of: unittest-data: Fix whitespace - indentation
of: unittest-data: Fix whitespace - blank lines
of: unittest-data: Convert remaining overlay DTS files to sugar syntax
of: overlay: unittest: Add test for unresolved symbol
of: unittest: Add separators to of_unittest_overlay_high_level()
of: unittest: Cleanup partially-applied overlays
of: unittest: Merge of_unittest_apply{,_revert}_overlay_check()
...
Pull ARM devicetree updates from Arnd Bergmann:
"These are the devicetree updates for Arm and RISC-V based SoCs, mainly
from Qualcomm, NXP/Freescale, Aspeed, TI, Rockchips, Samsung, ST and
Starfive.
Only a few new SoC got added:
- TI AM62P5, a variant of the existing Sitara AM62x family
- Intel Agilex5, an FPGFA platform that includes an Cortex-A76/A55
SoC.
- Qualcomm ipq5018 is used in wireless access points
- Qualcomm SM4450 (Snapdragon 4 Gen 2) is a new low-end mobile phone
platform.
In total, 29 machines get added, which is low because of the summer
break. These cover SoCs from Aspeed, Broadcom, NXP, Samsung, ST,
Allwinner, Amlogic, Intel, Qualcomm, Rockchip, TI and T-Head. Most of
these are development and reference boards.
Despite not adding a lot of new machines, there are over 700 patches
in total, most of which are cleanups and minor fixes"
* tag 'soc-dt-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (735 commits)
arm64: dts: use capital "OR" for multiple licenses in SPDX
ARM: dts: use capital "OR" for multiple licenses in SPDX
arm64: dts: qcom: sdm845-db845c: Mark cont splash memory region as reserved
ARM: dts: qcom: apq8064: add support to gsbi4 uart
riscv: dts: change TH1520 files to dual license
riscv: dts: thead: add BeagleV Ahead board device tree
dt-bindings: riscv: Add BeagleV Ahead board compatibles
ARM: dts: stm32: add SCMI PMIC regulators on stm32mp135f-dk board
ARM: dts: stm32: STM32MP13x SoC exposes SCMI regulators
dt-bindings: rcc: stm32: add STM32MP13 SCMI regulators IDs
ARM: dts: stm32: support display on stm32f746-disco board
ARM: dts: stm32: rename mmc_vcard to vcc-3v3 on stm32f746-disco
ARM: dts: stm32: add pin map for LTDC on stm32f7
ARM: dts: stm32: add ltdc support on stm32f746 MCU
arm64: dts: qcom: sm6350: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sdm670: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sa8775p: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sc8280xp: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sdm670: Add PDC
riscv: dts: starfive: fix jh7110 qspi sort order
...
- Add __counted_by to struct clk_hw_onecell_data and struct spmi_pmic_div_clk_cc
- Remove non-OF mmp clk drivers
- Move number of clks from DT headers to drivers
* clk-imx:
clk: imx: pll14xx: dynamically configure PLL for 393216000/361267200Hz
clk: imx: pll14xx: align pdiv with reference manual
clk: imx: composite-8m: fix clock pauses when set_rate would be a no-op
clk: imx25: make __mx25_clocks_init return void
clk: imx25: print silicon revision during init
dt-bindings: clocks: imx8mp: make sai4 a dummy clock
clk: imx8mp: fix sai4 clock
clk: imx: imx8ulp: update SPLL2 type
clk: imx: pllv4: Fix SPLL2 MULT range
clk: imx: imx8: add audio clock mux driver
dt-bindings: clock: fsl,imx8-acm: Add audio clock mux support
clk: imx: clk-imx8qxp-lpcg: Convert to devm_platform_ioremap_resource()
clk: imx: clk-gpr-mux: Simplify .determine_rate()
clk: imx: Add 519.75MHz frequency support for imx9 pll
clk: imx93: Add PDM IPG clk
dt-bindings: clock: imx93: Add PDM IPG clk
* clk-samsung:
dt-bindings: clock: samsung: remove define with number of clocks
clk: samsung: exynoautov9: do not define number of clocks in bindings
clk: samsung: exynos850: do not define number of clocks in bindings
clk: samsung: exynos7885: do not define number of clocks in bindings
clk: samsung: exynos5433: do not define number of clocks in bindings
clk: samsung: exynos5420: do not define number of clocks in bindings
clk: samsung: exynos5410: do not define number of clocks in bindings
clk: samsung: exynos5260: do not define number of clocks in bindings
clk: samsung: exynos5250: do not define number of clocks in bindings
clk: samsung: exynos4: do not define number of clocks in bindings
clk: samsung: exynos3250: do not define number of clocks in bindings
* clk-annotate:
clk: qcom: clk-spmi-pmic-div: Annotate struct spmi_pmic_div_clk_cc with __counted_by
clk: Annotate struct clk_hw_onecell_data with __counted_by
* clk-marvell:
clk: pxa910: Move number of clocks to driver source
clk: pxa1928: Move number of clocks to driver source
clk: pxa168: Move number of clocks to driver source
clk: mmp2: Move number of clocks to driver source
clk: mmp: Remove old non-OF clock drivers
* clk-lmk:
clk: lmk04832: Support using PLL1_LD as SPI readback pin
clk: lmk04832: Don't disable vco clock on probe fail
clk: lmk04832: Set missing parent_names for output clocks
- Add Versa3 clk generator to support 48KHz playback/record with audio
codec on RZ/G2L SMARC EVK
- Introduce kstrdup_and_replace() and use it
* clk-versa:
clk: vc7: Use i2c_get_match_data() instead of device_get_match_data()
clk: vc5: Use i2c_get_match_data() instead of device_get_match_data()
clk: versaclock3: Switch to use i2c_driver's probe callback
clk: Add support for versa3 clock driver
dt-bindings: clock: Add Renesas versa3 clock generator bindings
* clk-strdup:
clk: ti: Replace kstrdup() + strreplace() with kstrdup_and_replace()
clk: tegra: Replace kstrdup() + strreplace() with kstrdup_and_replace()
driver core: Replace kstrdup() + strreplace() with kstrdup_and_replace()
lib/string_helpers: Add kstrdup_and_replace() helper
* clk-amlogic: (22 commits)
dt-bindings: soc: amlogic: document System Control registers
dt-bindings: clock: amlogic: convert amlogic,gxbb-aoclkc.txt to dt-schema
dt-bindings: clock: amlogic: convert amlogic,gxbb-clkc.txt to dt-schema
clk: meson: axg-audio: move bindings include to main driver
clk: meson: meson8b: move bindings include to main driver
clk: meson: a1: move bindings include to main driver
clk: meson: eeclk: move bindings include to main driver
clk: meson: aoclk: move bindings include to main driver
dt-bindings: clk: axg-audio-clkc: expose all clock ids
dt-bindings: clk: amlogic,a1-pll-clkc: expose all clock ids
dt-bindings: clk: amlogic,a1-peripherals-clkc: expose all clock ids
dt-bindings: clk: meson8b-clkc: expose all clock ids
dt-bindings: clk: g12a-aoclkc: expose all clock ids
dt-bindings: clk: g12a-clks: expose all clock ids
dt-bindings: clk: axg-clkc: expose all clock ids
dt-bindings: clk: gxbb-clkc: expose all clock ids
clk: meson: migrate axg-audio out of hw_onecell_data to drop NR_CLKS
clk: meson: migrate meson8b out of hw_onecell_data to drop NR_CLKS
clk: meson: migrate a1 clock drivers out of hw_onecell_data to drop NR_CLKS
clk: meson: migrate meson-aoclk out of hw_onecell_data to drop NR_CLKS
...
* clk-allwinner:
clk: sunxi-ng: nkm: Prefer current parent rate
clk: sunxi-ng: a64: select closest rate for pll-video0
clk: sunxi-ng: div: Support finding closest rate
clk: sunxi-ng: mux: Support finding closest rate
clk: sunxi-ng: nkm: Support finding closest rate
clk: sunxi-ng: nm: Support finding closest rate
clk: sunxi-ng: Add helper function to find closest rate
clk: sunxi-ng: Add feature to find closest rate
clk: sunxi-ng: a64: allow pll-mipi to set parent's rate
clk: sunxi-ng: nkm: consider alternative parent rates when determining rate
clk: sunxi-ng: nkm: Use correct parameter name for parent HW
clk: sunxi-ng: Modify mismatched function name
clk: sunxi: sun9i-mmc: Use devm_platform_get_and_ioremap_resource()
* clk-rockchip:
clk: rockchip: rv1126: Add PD_VO clock tree
clk: rockchip: rk3568: Fix PLL rate setting for 78.75MHz
clk: rockchip: rk3568: Add PLL rate for 101MHz
Georgi writes:
interconnect changes for 6.6
This pull request contains the interconnect changes for the 6.6-rc1 merge
window which is a mix of core and driver changes with the following highlights:
Core changes:
- New generic test client driver that allows issuing bandwidth requests
between endpoints via debugfs.
- Annotate all structs with flexible array members with the __counted_by
attribute.
- Introduce new icc_bw_lock for cases where we need to serialize bandwidth
aggregation and update to decouple that from paths that require memory
allocation.
Driver changes:
- Move the Qualcomm SMD RPM bus-clocks from CCF to interconnect framework
where they actually belong. This brings power management improvements
and reduces the overhead and layering. These changes are in immutable
branch that is being pulled also into the qcom tree.
- Fixes for QUP nodes on SM8250.
- Enable sync_state and keepalive for QCM2290.
- Enable sync_state for SM8450.
- Improve enable_mask-based BCMs handling and fix some bugs.
- Add compatible string for the OSM-L3 on SDM670.
- Add compatible strings for SC7180, SM8250 and SM6350 bandwidth monitors.
- Expand and retire the DEFINE_QNODE and DEFINE_QBCM macros, which have
become ugly beasts with many different arguments.
Signed-off-by: Georgi Djakov <djakov@kernel.org>
* tag 'icc-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc: (64 commits)
interconnect: Add debugfs test client
interconnect: Reintroduce icc_get()
debugfs: Add write support to debugfs_create_str()
interconnect: qcom: icc-rpmh: Retire DEFINE_QBCM
interconnect: qcom: sm8350: Retire DEFINE_QBCM
interconnect: qcom: sm8250: Retire DEFINE_QBCM
interconnect: qcom: sm8150: Retire DEFINE_QBCM
interconnect: qcom: sm6350: Retire DEFINE_QBCM
interconnect: qcom: sdx65: Retire DEFINE_QBCM
interconnect: qcom: sdx55: Retire DEFINE_QBCM
interconnect: qcom: sdm845: Retire DEFINE_QBCM
interconnect: qcom: sdm670: Retire DEFINE_QBCM
interconnect: qcom: sc7180: Retire DEFINE_QBCM
interconnect: qcom: icc-rpmh: Retire DEFINE_QNODE
interconnect: qcom: sm8350: Retire DEFINE_QNODE
interconnect: qcom: sm8250: Retire DEFINE_QNODE
interconnect: qcom: sm8150: Retire DEFINE_QNODE
interconnect: qcom: sm6350: Retire DEFINE_QNODE
interconnect: qcom: sdx65: Retire DEFINE_QNODE
interconnect: qcom: sdx55: Retire DEFINE_QNODE
...
Documentation/process/license-rules.rst and checkpatch expect the SPDX
identifier syntax for multiple licenses to use capital "OR". Correct it
to keep consistent format and avoid copy-paste issues.
Correct also the format // -> .* in few Allwinner binding headers as
pointed out by checkpatch:
WARNING: Improper SPDX comment style for 'include/dt-bindings/reset/sun50i-h6-ccu.h', please use '/*' instead
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20230823084540.112602-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
Qualcomm ARM64 DeviceTree updates for v6.6
Initial support for the SM4450 platform and the QRD device thereon is
added.
The IPQ5018 platform is introduced, and the RDP432-C2 board thereon.
A shared definition of the IPQ5332 RDP is introduced, as is GPIO-based
LEDs and buttons.
On the IPQ9574 RDP433 USB, CPU cooling maps and regulators are added.
On MSM8916, the D3 camera mezzanine is improved and refactored out to
its own dts. The Samsung Galaxy S4 Mini gains support for its PMIC with
charger, while Samsung Galaxy J5 and E5 gains touchscreen support.
A few fixes for MSM8939 are introduced, and initial support for Samsung
Galaxy A7 is add.
Support for scaling the cache bus fabric is introduced on MSM8996. A
missing interrupt for the USB2 controller is added. The touchscreen vio
supply on Xiaomi Mi 5 is corrected, and a few other cleanups are
introduces across other devices.
The display controller is introduced for MSM8998, a few clock fixes are
introduced and missing power domains are added for the multimedia
subsystem iommu.
Reserved memory-regions and reserved GPIO lists are updated for the
QDU/QRU1000 IDPs.
USB3 PHY is added to the QCM2290, the RB1 gains regulators and GPU is
enabled for the RB2.
PCIe and Ethernet support is introduced on SA8775P, and enabled for the
Ride board.
On SC7180 the PSCI integration is refactored, to allow supporting
devices with the Qualcomm firmware. BWMON is introduced, alongside the
CPUfreq-based bus voting.
A number of fixes are added for SC8180X, on the Primus and Lenovo Flex
5G devices pmic_glink is introduced and wired up, to provide support for
external display.
Missing SCM interconnect is added to SC8280XP, and the PDC is marked as
wakeup-parent of TLMM. On the CRD the gpio for vreg_misc_3p3 is
corrected and a few regulators are renamed to align with schematics. The
Lenovo Thinkpad X13s gains camera activity LED and a set of previously
reserved GPIOs are released. The SA8540P Ride platform gains RTC
support.
For SDM670 CPU and L3 frequency scaling is added, the PDC is introduced
and wired up as wakeup-parent of the TLMM.
On SDM845 the UFS controller gains interconnect path description,
power-domain information is added to GCC and minimum frequency of the
UFS ICE is corrected. On RB3 continuous splash memory region is
described, and the camera subsystem is enabled. On the Lenovo Yoga C630
a missing power supply for the display panel is added, and the debug
UART is introduced.
SDX75 RPMh power-domains and SPMI controller are introduces, the PMX75
PMIC is described and added to the IDP.
GPU description is added to SM6115, and together with display enabled on
the Lenovo Tab P11.
On SM635 BWMON is introduced for LLCC and DDR scaling. Display and GPU
is added, and the PDC is registered as wakeup-parent of TLMM.
L3 cache scaling is introduced on SM6375.
The DSI PHY compatible and an interrupt for I2C7 are corrected for
SM8150, on the Sony Xperia 1 and 5 the ramoops pmsg size is corrected.
On SM8250 BWMONs are introduced for DDR and LLCC scaling, the UFS node
gains interconnect paths, SMMU is marked as DMA coherent and dynamic
power coefficients are updated. On Sony Xperia 1 II and 5 II GPIO line
names are updated.
On SM8350 missing cluster sleep states and LMH interrupts are added,
the CPU compatibles are corrected and APR and LPASS pinctrl support is
introduced. The HDK gains uSD card support and PMK8350 is added.
For SM8450 support for RNG and RPMh stats are added, the ICE handling is
extracted from the UFS node and the display subsystem gains a missing
interconnect path. Thermal description is improved for the HDK.
On SM8550 MTP and QRD the pmic_glink is introduced, to provide
DisplayPort output. A missing regulator supply is also added.
A few platforms that happens to share the RPMH power-domain resource
identifier constants are migrated to new generic defines. ADC channel
names are generalized on various PMICs.
A variety of devices gain chassis-type, and the GIC_SPI constant is
replacing the 0 across a few different platforms.
* tag 'qcom-arm64-for-6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (215 commits)
arm64: dts: qcom: sdm845-db845c: Mark cont splash memory region as reserved
arm64: dts: qcom: sm6350: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sdm670: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sa8775p: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sc8280xp: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sdm670: Add PDC
arm64: dts: qcom: msm8916-samsung-e5: Add touchscreen
arm64: dts: qcom: sc7180: Split up TF-A related PSCI configuration
arm64: dts: qcom: sc8280xp-x13s: Add camera activity LED
arm64: dts: qcom: sc8280xp-x13s: Unreserve NC pins
arm64: dts: qcom: msm8998: Add DPU1 nodes
arm64: dts: qcom: msm8996: Fix dsi1 interrupts
arm64: dts: qcom: sdx75-idp: Add regulator nodes
arm64: dts: qcom: sdx75: Add rpmhpd node
arm64: dts: qcom: sdx75-idp: Add pmics supported in SDX75
arm64: dts: qcom: Add pmx75 PMIC dtsi
arm64: dts: qcom: Add pm7550ba PMIC dtsi
arm64: dts: qcom: Add pinctrl gpio support for pm7250b
arm64: dts: qcom: sdx75: Add spmi node
arm64: dts: qcom: msm8998: Add missing power domain to MMSS SMMU
...
Link: https://lore.kernel.org/r/20230819034551.2537866-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
STM32 DT for v6.6, round 1
Highlights:
----------
- MCU:
- Add CAN support on stm32f746.
- Add touchscreen support (edt-ft5306) on stm32f746-disco.
- Add support to Rocktech RK043FN48H display on stm32f746-disco
board.
- Add gpio-ranges for stm32f7 to fix boot issue.
- MPU:
- STM32MP13:
- Remove shmem for scmi-optee to match with OP-TEE configuration.
- Enable OP-TEE asynchronous notification by using PPI#15.
- Expose and use SCMI regulators on stm32mp135f-dk.
- STMP32MP15:
- Remove shmem for scmi-optee to match with OPTEE configuration
- Deduplicate DSI node to fix #address-cells/#size-cells issue on
boards using it.
- ST:
- Fix dts check warnings on stm32mp15-scmi boards.
- DH:
- Add missing detach mailbox for DHCOM and DHCOR SoM.
- Odyssey:
- Add missing detach mailbox for Odyssey SoM.
- OCTAVO:
- Add Linux Automation Test Automation Controller (LXA TAC) based
on Octavo Systems OSD32MP15x SiP. It contains: eMMC,
DSA-capable ETH switch (2 ports), dual CAN...
It adds two boards support: lxa-tac-gen1 and lxa-tac-gen2 based
on STM32MP157.
- PROTONIC:
- Add Power over Data Line (PoDL) Power Source Equipment (PSE)
regulator nodes on PRTT1C board. It allows power delivery and
data transmission over a single twisted pair.
* tag 'stm32-dt-for-v6.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (29 commits)
ARM: dts: stm32: add SCMI PMIC regulators on stm32mp135f-dk board
ARM: dts: stm32: STM32MP13x SoC exposes SCMI regulators
dt-bindings: rcc: stm32: add STM32MP13 SCMI regulators IDs
ARM: dts: stm32: support display on stm32f746-disco board
ARM: dts: stm32: rename mmc_vcard to vcc-3v3 on stm32f746-disco
ARM: dts: stm32: add pin map for LTDC on stm32f7
ARM: dts: stm32: add ltdc support on stm32f746 MCU
ARM: dts: st: Add gpio-ranges for stm32f769-pinctrl
ARM: dts: st: Add gpio-ranges for stm32f746-pinctrl
ARM: dts: st: stm32mp157c-emstamp: correct regulator-active-discharge
ARM: dts: st: stm32mp157c-emstamp: drop incorrect vref_ddr property
ARM: dts: stm32: fix dts check warnings on stm32mp15-scmi
ARM: dts: stm32: Add missing detach mailbox for DHCOR SoM
ARM: dts: stm32: Add missing detach mailbox for DHCOM SoM
ARM: dts: stm32: Add missing detach mailbox for Odyssey SoM
ARM: dts: stm32: Add missing detach mailbox for emtrion emSBC-Argon
ARM: dts: stm32: prtt1c: Add PoDL PSE regulator nodes
ARM: dts: stm32: add touchscreen on stm32f746-disco board
ARM: dts: stm32: add pin map for i2c3 controller on stm32f7
ARM: dts: stm32: re-add CAN support on stm32f746
...
Link: https://lore.kernel.org/r/c0524a16-ab27-0cb5-8e7b-c12f7bde7e0d@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Qualcomm driver updates for v6.6
Compatible and clock handling in the Qualcomm SCM driver is cleaned up,
together with a couple stylistic cleanups and transition to mark
exported symbols GPL only.
An abstraction for the RPM subsystem is introduced, to make align the
structure of the SMD and GLINK nodes thereof with the structure when a
remoteproc is involved. This is done to facilitate associating
additional entities with the RPM subsystem.
The qmp_send() API is modified to not expose hardware requirements onto
the client drivers, and then further extended to allow command
formatting directly in the API, to facilitate this typical use case.
In the Qualcomm Command DB driver, NUL characters previously included in
identifiers are dropped from the debugfs, to facilitate scripting.
The thresholds of the BWMON driver are simplified to avoid hard coded
starting values.
The OCMEM driver is updated with some cleanups and fixes, and addition
of MSM8226 support.
PMIC_GLINK gains support for retimer switches, safe mode is selected
when the cable is disconnected from altmode and the same is enabled for
SM8550.
An off-by-one string length check is corrected in the QMI encoder
decoder library.
The RPMh tracepoints are extended to include the state of the request,
to provide needed context in the traced events.
The series from Ulf creating a genpd framework is integrated, to
facilitate the other changes to the cpr, rpmpd and rpmhpd driver.
SDX75 support is added to the rpmhpd driver, and the rpmpd driver is
extended with the same sync_state logic found in the rpmhpd driver.
The socinfo driver gains knowledge about SM4450 and SM7125, the IPQ5019
platform is dropped.
Clock handling in the GSBI driver is cleaned up with the use of
devm_clk_get_enabled().
The list of VMIDs defined for the SCM assign memory interface is
extended.
* tag 'qcom-drivers-for-6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (52 commits)
soc: qcom: aoss: Tidy up qmp_send() callers
soc: qcom: aoss: Format string in qmp_send()
soc: qcom: aoss: Move length requirements from caller
dt-bindings: firmware: qcom: scm: Updating VMID list
dt-bindings: qcom: Update RPMHPD entries for some SoCs
soc: qcom: qmi_encdec: Restrict string length in decode
soc: qcom: smem: Fix incompatible types in comparison
soc: qcom: ocmem: add missing clk_disable_unprepare() in ocmem_dev_probe()
soc: qcom: socinfo: Add SoC ID for SM7125
dt-bindings: arm: qcom,ids: Add SoC ID for SM7125
dt-bindings: arm: qcom,ids: drop the IPQ5019 SoC ID
soc: qcom: socinfo: drop the IPQ5019 SoC ID
soc: qcom: socinfo: add SM4450 ID
dt-bindings: arm: qcom,ids: add SoC ID for SM4450
soc: qcom: pmic_glink: enable altmode for SM8550
soc: qcom: pmic_glink_altmode: add retimer-switch support
soc: qcom: pmic_glink_altmode: handle safe mode when disconnect
soc: qcom: rpmhpd: Add SDX75 power domains
dt-bindings: power: qcom,rpmpd: Add compatible for sdx75
genpd: Makefile: build imx
...
Link: https://lore.kernel.org/r/20230818023338.2484467-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
TI K3 device tree updates for v6.6
New Boards:
- TQ group's TQMaX4XxL AM64 SOM and MBaX4XxL carrier board
- TI's AM62P5 Starter Kit (SK)
New features:
AM625:
- Support for Display (parallel only) - hdmi+audio support for
AM625-SK/BeaglePlay, TC358778 DPI to MIPI-DSI bridge support
for verdin.
- MCU MCAN support and enable of Toradex Verdin
- Toradex Verdin Dahlia audio support
AM62A7:
- MCU MCAN support
- Enable USB Dual Role Device(DRD) support for AM62A7
Starter Kit(SK).
AM64:
- TQ group's tqma64xxl: Overlays for SD-card and wlan.
J721E:
- Main domain CPSW9G and correponding gateway/ethernet
switch expansion - GESI board.
J721S2/AM68:
- New CAN instances, ehrpwm, Display (DSS) and am68-sk HDMI support
- Main domain CPSW2G and correponding gateway/ethernet
switch expansion - GESI board.
J784S4/AM69:
- Boot phase tag marking in device tree
- UFS support
Cleanups and non-urgent fixes:
- Cosmetic style fixups around "=" and "{" whitespace usage.
- Fixups across multiple SoCs/boards for pwm-tbclk to matchup with
bindings
- Serdes header file include/dt-bindings/mux/ti-serdes.h is now
deprecated, use k3-serdes.h in soc dtsi folder.
- All SoCs: Enable GPIO/SDHCI/OSPI/TSADC/C6/C7 DSP nodes at the
board level.
- Fixups for AM62: Crypto powerdomains are conditional to better
represent control of the crypto engines by security controller.
- Fixups for j721e: Duplicate wakeup_i2c node dropped for SoM board.
- Fixups for j721s2/am68: pimux offsets for OSPI.
- Fixups for j784s4/am69: Fixups for pinmux for ospi/adc interrupt
ranges for wkup/main gpios
* tag 'ti-k3-dt-for-v6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux: (68 commits)
arm64: dts: ti: verdin-am62: Add DSI display support
arm64: dts: ti: Add support for the AM62P5 Starter Kit
arm64: dts: ti: Introduce AM62P5 family of SoCs
dt-bindings: arm: ti: Add bindings for AM62P5 SoCs
arm64: dts: ti: k3-am69-sk: Add phase tags marking
arm64: dts: ti: k3-j784s4-evm: Add phase tags marking
arm64: dts: ti: k3-j784s4: Add phase tags marking
arm64: dts: ti: k3-am625-beagleplay: Add HDMI support
arm64: dts: ti: am62x-sk: Add overlay for HDMI audio
arm64: dts: ti: k3-am62x-sk-common: Add HDMI support
arm64: dts: ti: k3-am62-main: Add node for DSS
arm64: dts: ti: k3-am62x-sk-common: Update main-i2c1 frequency
arm64: dts: ti: k3-j721e: Enable C6x DSP nodes at the board level
arm64: dts: ti: k3-j784s4: Enable C7x DSP nodes at the board level
arm64: dts: ti: k3-j721e: Enable C7x DSP nodes at the board level
arm64: dts: ti: k3-*: fix fss node dtbs check warnings
arm64: dts: ti: k3-am64: Enable TSCADC nodes at the board level
arm64: dts: ti: k3-am65: Enable TSCADC nodes at the board level
arm64: dts: ti: k3-j721e: Enable TSCADC nodes at the board level
arm64: dts: ti: k3-j7200: Enable GPIO nodes at the board level
...
Link: https://lore.kernel.org/r/20230814160651.frxohyshd2evp2k4@expenses
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add the clock dt-binding file for Audio Clock Mux. which
is the IP for i.MX8QM, i.MX8QXP, i.MX8DXL.
Add the clockid for clocks in header file.
The Audio Clock Mux is binded with all the audio IP and audio clocks
in the subsystem, so need to list the power domain of related clocks
and IPs. Each clock and IP has a power domain, so there are so many
power domains.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/1690260984-25744-2-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
