Add the bare minimum needed to boot BCM2708 from a Device Tree.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
BCM2708: DT: change 'axi' nodename to 'soc'
Change DT node named 'axi' to 'soc' so it matches ARCH_BCM2835.
The VC4 bootloader fills in certain properties in the 'axi' subtree,
but since this is part of an upstreaming effort, the name is changed.
Signed-off-by: Noralf Tronnes notro@tronnes.org
BCM2708_DT: Correct length of the peripheral space
Use dts-dirs feature for overlays.
The kernel makefiles have a dts-dirs target that is for vendor subdirectories.
Using this fixes the install_dtbs target, which previously did not install the overlays.
BCM270X_DT: configure I2S DMA channels
Signed-off-by: Matthias Reichl <hias@horus.com>
BCM270X_DT: switch to bcm2835-i2s
I2S soundcard drivers with proper devicetree support (i.e. not linking
to the cpu_dai/platform via name but to cpu/platform via of_node)
will work out of the box without any modifications.
When the kernel is compiled without devicetree support the platform
code will instantiate the bcm2708-i2s driver and I2S soundcard drivers
will link to it via name, as before.
Signed-off-by: Matthias Reichl <hias@horus.com>
SDIO-overlay: add poll_once-boolean parameter
Add paramter to toggle sdio-device-polling
done every second or once at boot-time.
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
BCM270X_DT: Make mmc overlay compatible with current firmware
The original DT overlay logic followed a merge-then-patch procedure,
i.e. parameters are applied to the loaded overlay before the overlay
is merged into the base DTB. This sequence has been changed to
patch-then-merge, in order to support parameterised node names, and
to protect against bad overlays. As a result, overrides (parameters)
must only target labels in the overlay, but the overlay can obviously target nodes in the base DTB.
mmc-overlay.dts (that switches back to the original mmc sdcard
driver) is the only overlay violating that rule, and this patch
fixes it.
bcm270x_dt: Use the sdhost MMC controller by default
The "mmc" overlay reverts to using the other controller.
squash: Add cprman to dt
BCM270X_DT: Use clk_core for I2C interfaces
BCM270X_DT: Use bcm283x.dtsi, bcm2835.dtsi and bcm2836.dtsi
The mainline Device Tree files are quite close to downstream now.
Let's use bcm283x.dtsi, bcm2835.dtsi and bcm2836.dtsi as base files
for our dts files.
Mainline dts files are based on these files:
bcm2835-rpi.dtsi
bcm2835.dtsi bcm2836.dtsi
bcm283x.dtsi
Current downstream are based on these:
bcm2708.dtsi bcm2709.dtsi bcm2710.dtsi
bcm2708_common.dtsi
This patch introduces this dependency:
bcm2708.dtsi bcm2709.dtsi
bcm2708-rpi.dtsi
bcm270x.dtsi
bcm2835.dtsi bcm2836.dtsi
bcm283x.dtsi
And:
bcm2710.dtsi
bcm2708-rpi.dtsi
bcm270x.dtsi
bcm283x.dtsi
bcm270x.dtsi contains the downstream bcm283x.dtsi diff.
bcm2708-rpi.dtsi is the downstream version of bcm2835-rpi.dtsi.
Other changes:
- The led node has moved from /soc/leds to /leds. This is not a problem
since the label is used to reference it.
- The clk_osc reg property changes from 6 to 3.
- The gpu nodes has their interrupt property set in the base file.
- the clocks label does not point to the /clocks node anymore, but
points to the cprman node. This is not a problem since the overlays
that use the clock node refer to it directly: target-path = "/clocks";
- some nodes now have 2 labels since mainline and downstream differs in
this respect: cprman/clocks, spi0/spi, gpu/vc4.
- some nodes doesn't have an explicit status = "okay" since they're not
disabled in the base file: watchdog and random.
- gpiomem doesn't need an explicit status = "okay".
- bcm2708-rpi-cm.dts got the hpd-gpios property from bcm2708_common.dtsi,
it's now set directly in that file.
- bcm2709-rpi-2-b.dts has the timer node moved from /soc/timer to /timer.
- Removed clock-frequency property on the bcm{2709,2710}.dtsi timer nodes.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270X_DT: Use raspberrypi-power to turn on USB power
Use the raspberrypi-power driver to turn on USB power.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270X_DT: Add a .dtbo target, use for overlays
Change the filenames and extensions to keep the pre-DDT style of
overlay (<name>-overlay.dtb) distinct from new ones that use a
different style of local fixups (<name>.dtbo), and to match other
platforms.
The RPi firmware uses the DDTK trailer atom to choose which type of
overlay to use for each kernel.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Don't generate "linux,phandle" props
The EPAPR standard says to use "phandle" properties to store phandles,
rather than the deprecated "linux,phandle" version. By default, dtc
generates both, but adding "-H epapr" causes it to only generate
"phandle"s, saving some space and clutter.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Add overlay for enc28j60 on SPI2
Works on SPI2 for compute module
BCM270X_DT: Add midi-uart0 overlay
MIDI requires 31.25kbaud, a baudrate unsupported by Linux. The
midi-uart0 overlay configures uart0 (ttyAMA0) to use a fake clock
so that requesting 38.4kbaud actually gets 31.25kbaud.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Add i2c-sensor overlay
The i2c-sensor overlay is a container for various pressure and
temperature sensors, currently bmp085 and bmp280. The standalone
bmp085_i2c-sensor overlay is now deprecated.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: overlays/*-overlay.dtb -> overlays/*.dtbo (#1752)
We now create overlays as .dtbo files.
build: support for .dtbo files for dtb overlays
Kernel 4.4.6+ on RaspberryPi support .dtbo files for overlays, instead of .dtb.
Patch the kernel, which has faulty rules to generate .dtbo the way yocto does
Signed-off-by: Herve Jourdain <herve.jourdain@neuf.fr>
Signed-off-by: Khem Raj <raj.khem@gmail.com>
BCM270X: Drop position requirement for CMA in VC4 overlay.
No longer necessary since 2aefcd5761,
and will probably let peeople that want to choose a larger CMA
allocation (particularly on pi0/1).
Signed-off-by: Eric Anholt <eric@anholt.net>
BCM270X_DT: RPi Device Tree tidy
Use the upstream sdhost node, add thermal-zones, and factor out some
common elements.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
kbuild: Silence unhelpful DTC warnings
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: DT build rules no longer arch-specific
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The Raspberry Pi firmware looks for a trailer on the kernel image to
determine whether it was compiled with Device Tree support enabled.
If the firmware finds a kernel without this trailer, or which has a
trailer indicating that it isn't DT-capable, it disables DT support
and reverts to using ATAGs.
The mkknlimg utility adds that trailer, having first analysed the
image to look for signs of DT support and the kernel version string.
knlinfo displays the contents of the trailer in the given kernel image.
scripts/mkknlimg: Add support for ARCH_BCM2835
Add a new trailer field indicating whether this is an ARCH_BCM2835
build, as opposed to MACH_BCM2708/9. If the loader finds this flag
is set it changes the default base dtb file name from bcm270x...
to bcm283y...
Also update knlinfo to show the status of the field.
scripts/mkknlimg: Improve ARCH_BCM2835 detection
The board support code contains sufficient strings to be able to
distinguish 2708 vs. 2835 builds, so remove the check for
bcm2835-pm-wdt which could exist in either.
Also, since the canned configuration is no longer built in (it's
a module), remove the config string checking.
See: https://github.com/raspberrypi/linux/issues/1157
scripts: Multi-platform support for mkknlimg and knlinfo
The firmware uses tags in the kernel trailer to choose which dtb file
to load. Current firmware loads bcm2835-*.dtb if the '283x' tag is true,
otherwise it loads bcm270*.dtb. This scheme breaks if an image supports
multiple platforms.
This patch adds '270X' and '283X' tags to indicate support for RPi and
upstream platforms, respectively. '283x' (note lower case 'x') is left
for old firmware, and is only set if the image only supports upstream
builds.
scripts/mkknlimg: Append a trailer for all input
Now that the firmware assumes an unsigned kernel is DT-capable, it is
helpful to be able to mark a kernel as being non-DT-capable.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
scripts/knlinfo: Decode DDTK atom
Show the DDTK atom as being a boolean.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mkknlimg: Retain downstream-kernel detection
With the death of ARCH_BCM2708 and ARCH_BCM2709, a new way is needed to
determine if this is a "downstream" build that wants the firmware to
load a bcm27xx .dtb. The vc_cma driver is used downstream but not
upstream, making vc_cma_init a suitable predicate symbol.
mkknlimg: Find some more downstream-only strings
See: https://github.com/raspberrypi/linux/issues/1920
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
scripts: Update mkknlimg, just in case
With the removal of the vc_cma driver, mkknlimg lost an indication that
the user had built a downstream kernel. Update the script, adding a few
more key strings, in case it is still being used.
Note that mkknlimg is now deprecated, except to tag kernels as upstream
(283x), and thus requiring upstream DTBs.
See: https://github.com/raspberrypi/linux/issues/2239
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
[ Upstream commit 34b5560db4 ]
The generic Makefile.kasan propagates CONFIG_KASAN_SHADOW_OFFSET into
KASAN_SHADOW_OFFSET, but only does so for CONFIG_KASAN_GENERIC.
Since commit:
6bd1d0be0e ("arm64: kasan: Switch to using KASAN_SHADOW_OFFSET")
... arm64 defines CONFIG_KASAN_SHADOW_OFFSET in Kconfig rather than
defining KASAN_SHADOW_OFFSET in a Makefile. Thus, if
CONFIG_KASAN_SW_TAGS && KASAN_INLINE are selected, we get build time
splats due to KASAN_SHADOW_OFFSET not being set:
| [mark@lakrids:~/src/linux]% usellvm 8.0.1 usekorg 8.1.0 make ARCH=arm64 CROSS_COMPILE=aarch64-linux- CC=clang
| scripts/kconfig/conf --syncconfig Kconfig
| CC scripts/mod/empty.o
| clang (LLVM option parsing): for the -hwasan-mapping-offset option: '' value invalid for uint argument!
| scripts/Makefile.build:273: recipe for target 'scripts/mod/empty.o' failed
| make[1]: *** [scripts/mod/empty.o] Error 1
| Makefile:1123: recipe for target 'prepare0' failed
| make: *** [prepare0] Error 2
Let's fix this by always propagating CONFIG_KASAN_SHADOW_OFFSET into
KASAN_SHADOW_OFFSET if CONFIG_KASAN is selected, moving the existing
common definition of +CFLAGS_KASAN_NOSANITIZE to the top of
Makefile.kasan.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Tested-by Steve Capper <steve.capper@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8de12fb7c ]
If the particular version of clang a user has doesn't enable
-Werror=unknown-warning-option by default, even though it is the
default[1], then make sure to pass the option to the Kconfig cc-option
command so that testing options from Kconfig files works properly.
Otherwise, depending on the default values setup in the clang toolchain
we will silently assume options such as -Wmaybe-uninitialized are
supported by clang, when they really aren't.
A compilation issue only started happening for me once commit
589834b3a0 ("kbuild: Add -Werror=unknown-warning-option to
CLANG_FLAGS") was applied on top of commit b303c6df80 ("kbuild:
compute false-positive -Wmaybe-uninitialized cases in Kconfig"). This
leads kbuild to try and test for the existence of the
-Wmaybe-uninitialized flag with the cc-option command in
scripts/Kconfig.include, and it doesn't see an error returned from the
option test so it sets the config value to Y. Then the Makefile tries to
pass the unknown option on the command line and
-Werror=unknown-warning-option catches the invalid option and breaks the
build. Before commit 589834b3a0 ("kbuild: Add
-Werror=unknown-warning-option to CLANG_FLAGS") the build works fine,
but any cc-option test of a warning option in Kconfig files silently
evaluates to true, even if the warning option flag isn't supported on
clang.
Note: This doesn't change cc-option usages in Makefiles because those
use a different rule that includes KBUILD_CFLAGS by default (see the
__cc-option command in scripts/Kbuild.incluide). The KBUILD_CFLAGS
variable already has the -Werror=unknown-warning-option flag set. Thanks
to Doug for pointing out the different rule.
[1] https://clang.llvm.org/docs/DiagnosticsReference.html#wunknown-warning-option
Cc: Peter Smith <peter.smith@linaro.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb4819934a ]
KBUILD_EXTRA_SYMBOLS makes sense only when building external modules.
Moreover, the modpost sets 'external_module' if the -e option is given.
I replaced $(patsubst %, -e %,...) with simpler $(addprefix -e,...)
while I was here.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb36955a55 ]
Running gen_compile_commands.py after building the kernel with
allnoconfig gave this:
$ ./scripts/gen_compile_commands.py
WARNING: Found 449 entries. Have you compiled the kernel?
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 353290a9eb ]
The name of the package with carries latexmk is different
on two distros:
- On OpenSUSE, latexmk is packaged as "texlive-latexmk-bin"
- On Mageia, latexmk is packaged at "texlive-collection-basic"
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b308467c91 ]
There's a missing parenthesis at the script, with causes it to
fail to detect non-Fedora releases (e. g. RHEL/CentOS).
Tested with Centos 7.6.1810.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 944cfe9be1 upstream.
If a build rule fails, the .DELETE_ON_ERROR special target removes the
target, but does nothing for the .*.cmd file, which might be corrupted.
So, .*.cmd files should be included only when the corresponding targets
exist.
Commit 392885ee82 ("kbuild: let fixdep directly write to .*.cmd
files") missed to fix up this file.
Fixes: 392885ee82 ("kbuild: let fixdep directly write to .*.cmd")
Cc: <stable@vger.kernel.org> # v5.0+
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c5b6c28ed upstream.
Prior to this commit, starting nconfig, xconfig or gconfig, and saving
the .config file more than once caused data loss, where a .config file
that contained only comments would be written to disk starting from the
second save operation.
This bug manifests itself because the SYMBOL_WRITTEN flag is never
cleared after the first call to conf_write, and subsequent calls to
conf_write then skip all of the configuration symbols due to the
SYMBOL_WRITTEN flag being set.
This commit resolves this issue by clearing the SYMBOL_WRITTEN flag
from all symbols before conf_write returns.
Fixes: 8e2442a5f8 ("kconfig: fix missing choice values in auto.conf")
Cc: linux-stable <stable@vger.kernel.org> # 4.19+
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 33177f01ca ]
gcc asan instrumentation emits the following sequence to store frame pc
when the kernel is built with CONFIG_RELOCATABLE:
debug/vsprintf.s:
.section .data.rel.ro.local,"aw"
.align 8
.LC3:
.quad .LASANPC4826@GOTOFF
.text
.align 8
.type number, @function
number:
.LASANPC4826:
and in case reloc is issued for LASANPC label it also gets into .symtab
with the same address as actual function symbol:
$ nm -n vmlinux | grep 0000000001397150
0000000001397150 t .LASANPC4826
0000000001397150 t number
In the end kernel backtraces are almost unreadable:
[ 143.748476] Call Trace:
[ 143.748484] ([<000000002da3e62c>] .LASANPC2671+0x114/0x190)
[ 143.748492] [<000000002eca1a58>] .LASANPC2612+0x110/0x160
[ 143.748502] [<000000002de9d830>] print_address_description+0x80/0x3b0
[ 143.748511] [<000000002de9dd64>] __kasan_report+0x15c/0x1c8
[ 143.748521] [<000000002ecb56d4>] strrchr+0x34/0x60
[ 143.748534] [<000003ff800a9a40>] kasan_strings+0xb0/0x148 [test_kasan]
[ 143.748547] [<000003ff800a9bba>] kmalloc_tests_init+0xe2/0x528 [test_kasan]
[ 143.748555] [<000000002da2117c>] .LASANPC4069+0x354/0x748
[ 143.748563] [<000000002dbfbb16>] do_init_module+0x136/0x3b0
[ 143.748571] [<000000002dbff3f4>] .LASANPC3191+0x2164/0x25d0
[ 143.748580] [<000000002dbffc4c>] .LASANPC3196+0x184/0x1b8
[ 143.748587] [<000000002ecdf2ec>] system_call+0xd8/0x2d8
Since LASANPC labels are not even unique and get into .symtab only due
to relocs filter them out in kallsyms.
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80e5302e4b ]
An impending change to enable HAVE_C_RECORDMCOUNT on powerpc leads to
warnings such as the following:
# modprobe kprobe_example
ftrace-powerpc: Not expected bl: opcode is 3c4c0001
WARNING: CPU: 0 PID: 227 at kernel/trace/ftrace.c:2001 ftrace_bug+0x90/0x318
Modules linked in:
CPU: 0 PID: 227 Comm: modprobe Not tainted 5.2.0-rc6-00678-g1c329100b942 #2
NIP: c000000000264318 LR: c00000000025d694 CTR: c000000000f5cd30
REGS: c000000001f2b7b0 TRAP: 0700 Not tainted (5.2.0-rc6-00678-g1c329100b942)
MSR: 900000010282b033 <SF,HV,VEC,VSX,EE,FP,ME,IR,DR,RI,LE,TM[E]> CR: 28228222 XER: 00000000
CFAR: c0000000002642fc IRQMASK: 0
<snip>
NIP [c000000000264318] ftrace_bug+0x90/0x318
LR [c00000000025d694] ftrace_process_locs+0x4f4/0x5e0
Call Trace:
[c000000001f2ba40] [0000000000000004] 0x4 (unreliable)
[c000000001f2bad0] [c00000000025d694] ftrace_process_locs+0x4f4/0x5e0
[c000000001f2bb90] [c00000000020ff10] load_module+0x25b0/0x30c0
[c000000001f2bd00] [c000000000210cb0] sys_finit_module+0xc0/0x130
[c000000001f2be20] [c00000000000bda4] system_call+0x5c/0x70
Instruction dump:
419e0018 2f83ffff 419e00bc 2f83ffea 409e00cc 4800001c 0fe00000 3c62ff96
39000001 39400000 386386d0 480000c4 <0fe00000> 3ce20003 39000001 3c62ff96
---[ end trace 4c438d5cebf78381 ]---
ftrace failed to modify
[<c0080000012a0008>] 0xc0080000012a0008
actual: 01:00:4c:3c
Initializing ftrace call sites
ftrace record flags: 2000000
(0)
expected tramp: c00000000006af4c
Looking at the relocation records in __mcount_loc shows a few spurious
entries:
RELOCATION RECORDS FOR [__mcount_loc]:
OFFSET TYPE VALUE
0000000000000000 R_PPC64_ADDR64 .text.unlikely+0x0000000000000008
0000000000000008 R_PPC64_ADDR64 .text.unlikely+0x0000000000000014
0000000000000010 R_PPC64_ADDR64 .text.unlikely+0x0000000000000060
0000000000000018 R_PPC64_ADDR64 .text.unlikely+0x00000000000000b4
0000000000000020 R_PPC64_ADDR64 .init.text+0x0000000000000008
0000000000000028 R_PPC64_ADDR64 .init.text+0x0000000000000014
The first entry in each section is incorrect. Looking at the
relocation records, the spurious entries correspond to the
R_PPC64_ENTRY records:
RELOCATION RECORDS FOR [.text.unlikely]:
OFFSET TYPE VALUE
0000000000000000 R_PPC64_REL64 .TOC.-0x0000000000000008
0000000000000008 R_PPC64_ENTRY *ABS*
0000000000000014 R_PPC64_REL24 _mcount
<snip>
The problem is that we are not validating the return value from
get_mcountsym() in sift_rel_mcount(). With this entry, mcountsym is 0,
but Elf_r_sym(relp) also ends up being 0. Fix this by ensuring
mcountsym is valid before processing the entry.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Tested-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f9ac9f442 ]
When there is not enough space on your storage device, the build will
fail with 'No space left on device' error message.
The reason is obvious from the message, so you will free up some disk
space, then you will resume the build.
However, sometimes you may still see a mysterious error message:
unterminated call to function 'wildcard': missing ')'.
If you run out of the disk space, fixdep may end up with generating
incomplete .*.cmd files.
For example, if the disk-full error occurs while fixdep is running
print_dep(), the .*.cmd might be truncated like this:
$(wildcard include/config/
When you run 'make' next time, this broken .*.cmd will be included,
then Make will terminate parsing since it is a wrong syntax.
Once this happens, you need to run 'make clean' or delete the broken
.*.cmd file manually.
Even if you do not see any error message, the .*.cmd files after any
error could be potentially incomplete, and unreliable. You may miss
the re-compilation due to missing header dependency.
If printf() cannot output the string for disk shortage or whatever
reason, it returns a negative value, but currently fixdep does not
check it at all. Consequently, fixdep *successfully* generates a
broken .*.cmd file. Make never notices that since fixdep exits with 0,
which means success.
Given the intended usage of fixdep, it must respect the return value
of not only malloc(), but also printf() and putchar().
This seems a long-standing issue since the introduction of fixdep.
In old days, Kbuild tried to provide an extra safety by letting fixdep
output to a temporary file and renaming it after everything is done:
scripts/basic/fixdep $(depfile) $@ '$(make-cmd)' > $(dot-target).tmp;\
rm -f $(depfile); \
mv -f $(dot-target).tmp $(dot-target).cmd)
It was no help to avoid the current issue; fixdep successfully created
a truncated tmp file, which would be renamed to a .*.cmd file.
This problem should be fixed by propagating the error status to the
build system because:
[1] Since commit 9c2af1c737 ("kbuild: add .DELETE_ON_ERROR special
target"), Make will delete the target automatically on any failure
in the recipe.
[2] Since commit 392885ee82 ("kbuild: let fixdep directly write to
.*.cmd files"), .*.cmd file is included only when the corresponding
target already exists.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a222061b85 ]
__uint128_t crops up in a few files that export symbols to modules, so
teach genksyms about it and the other GCC built-in 128-bit integer types
so that we don't end up skipping the CRC generation for some symbols due
to the parser failing to spot them:
| WARNING: EXPORT symbol "kernel_neon_begin" [vmlinux] version
| generation failed, symbol will not be versioned.
| ld: arch/arm64/kernel/fpsimd.o: relocation R_AARCH64_ABS32 against
| `__crc_kernel_neon_begin' can not be used when making a shared
| object
| ld: arch/arm64/kernel/fpsimd.o:(.data+0x0): dangerous relocation:
| unsupported relocation
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8e2442a5f8 upstream.
Since commit 00c864f890 ("kconfig: allow all config targets to write
auto.conf if missing"), Kconfig creates include/config/auto.conf in the
defconfig stage when it is missing.
Joonas Kylmälä reported incorrect auto.conf generation under some
circumstances.
To reproduce it, apply the following diff:
| --- a/arch/arm/configs/imx_v6_v7_defconfig
| +++ b/arch/arm/configs/imx_v6_v7_defconfig
| @@ -345,14 +345,7 @@ CONFIG_USB_CONFIGFS_F_MIDI=y
| CONFIG_USB_CONFIGFS_F_HID=y
| CONFIG_USB_CONFIGFS_F_UVC=y
| CONFIG_USB_CONFIGFS_F_PRINTER=y
| -CONFIG_USB_ZERO=m
| -CONFIG_USB_AUDIO=m
| -CONFIG_USB_ETH=m
| -CONFIG_USB_G_NCM=m
| -CONFIG_USB_GADGETFS=m
| -CONFIG_USB_FUNCTIONFS=m
| -CONFIG_USB_MASS_STORAGE=m
| -CONFIG_USB_G_SERIAL=m
| +CONFIG_USB_FUNCTIONFS=y
| CONFIG_MMC=y
| CONFIG_MMC_SDHCI=y
| CONFIG_MMC_SDHCI_PLTFM=y
And then, run:
$ make ARCH=arm mrproper imx_v6_v7_defconfig
You will see CONFIG_USB_FUNCTIONFS=y is correctly contained in the
.config, but not in the auto.conf.
Please note drivers/usb/gadget/legacy/Kconfig is included from a choice
block in drivers/usb/gadget/Kconfig. So USB_FUNCTIONFS is a choice value.
This is probably a similar situation described in commit beaaddb625
("kconfig: tests: test defconfig when two choices interact").
When sym_calc_choice() is called, the choice symbol forgets the
SYMBOL_DEF_USER unless all of its choice values are explicitly set by
the user.
The choice symbol is given just one chance to recall it because
set_all_choice_values() is called if SYMBOL_NEED_SET_CHOICE_VALUES
is set.
When sym_calc_choice() is called again, the choice symbol forgets it
forever, since SYMBOL_NEED_SET_CHOICE_VALUES is a one-time aid.
Hence, we cannot call sym_clear_all_valid() again and again.
It is crazy to repeat set and unset of internal flags. However, we
cannot simply get rid of "sym->flags &= flags | ~SYMBOL_DEF_USER;"
Doing so would re-introduce the problem solved by commit 5d09598d48
("kconfig: fix new choices being skipped upon config update").
To work around the issue, conf_write_autoconf() stopped calling
sym_clear_all_valid().
conf_write() must be changed accordingly. Currently, it clears
SYMBOL_WRITE after the symbol is written into the .config file. This
is needed to prevent it from writing the same symbol multiple times in
case the symbol is declared in two or more locations. I added the new
flag SYMBOL_WRITTEN, to track the symbols that have been written.
Anyway, this is a cheesy workaround in order to suppress the issue
as far as defconfig is concerned.
Handling of choices is totally broken. sym_clear_all_valid() is called
every time a user touches a symbol from the GUI interface. To reproduce
it, just add a new symbol drivers/usb/gadget/legacy/Kconfig, then touch
around unrelated symbols from menuconfig. USB_FUNCTIONFS will disappear
from the .config file.
I added the Fixes tag since it is more fatal than before. But, this
has been broken since long long time before, and still it is.
We should take a closer look to fix this correctly somehow.
Fixes: 00c864f890 ("kconfig: allow all config targets to write auto.conf if missing")
Cc: linux-stable <stable@vger.kernel.org> # 4.19+
Reported-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At least for ARM64 kernels compiled with the crosstoolchain from
Debian/stretch or with the toolchain from kernel.org the line number is
not decoded correctly by 'decode_stacktrace.sh':
$ echo "[ 136.513051] f1+0x0/0xc [kcrash]" | \
CROSS_COMPILE=/opt/gcc-8.1.0-nolibc/aarch64-linux/bin/aarch64-linux- \
./scripts/decode_stacktrace.sh /scratch/linux-arm64/vmlinux \
/scratch/linux-arm64 \
/nfs/debian/lib/modules/4.20.0-devel
[ 136.513051] f1 (/linux/drivers/staging/kcrash/kcrash.c:68) kcrash
If addr2line from the toolchain is used the decoded line number is correct:
[ 136.513051] f1 (/linux/drivers/staging/kcrash/kcrash.c:57) kcrash
Link: http://lkml.kernel.org/r/20190527083425.3763-1-manut@linutronix.de
Signed-off-by: Manuel Traut <manut@linutronix.de>
Acked-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull yet more SPDX updates from Greg KH:
"Another round of SPDX header file fixes for 5.2-rc4
These are all more "GPL-2.0-or-later" or "GPL-2.0-only" tags being
added, based on the text in the files. We are slowly chipping away at
the 700+ different ways people tried to write the license text. All of
these were reviewed on the spdx mailing list by a number of different
people.
We now have over 60% of the kernel files covered with SPDX tags:
$ ./scripts/spdxcheck.py -v 2>&1 | grep Files
Files checked: 64533
Files with SPDX: 40392
Files with errors: 0
I think the majority of the "easy" fixups are now done, it's now the
start of the longer-tail of crazy variants to wade through"
* tag 'spdx-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (159 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 450
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 449
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 448
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 446
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 445
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 444
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 443
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 442
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 441
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 440
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 438
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 437
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 436
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 435
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 434
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 433
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 432
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 431
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 430
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 429
...
To print the pathname that will be used by shell in the current
environment, 'command -v' is a standardized way. [1]
'which' is also often used in scripts, but it is less portable.
When I worked on commit bd55f96fa9 ("kbuild: refactor cc-cross-prefix
implementation"), I was eager to use 'command -v' but it did not work.
(The reason is explained below.)
I kept 'which' as before but got rid of '> /dev/null 2>&1' as I
thought it was no longer needed. Sorry, I was wrong.
It works well on my Ubuntu machine, but Alexey Brodkin reports noisy
warnings on CentOS7 when 'which' fails to find the given command in
the PATH environment.
$ which foo
which: no foo in (/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin)
Given that behavior of 'which' depends on system (and it may not be
installed by default), I want to try 'command -v' once again.
The specification [1] clearly describes the behavior of 'command -v'
when the given command is not found:
Otherwise, no output shall be written and the exit status shall reflect
that the name was not found.
However, we need a little magic to use 'command -v' from Make.
$(shell ...) passes the argument to a subshell for execution, and
returns the standard output of the command.
Here is a trick. GNU Make may optimize this by executing the command
directly instead of forking a subshell, if no shell special characters
are found in the command and omitting the subshell will not change the
behavior.
In this case, no shell special character is used. So, Make will try
to run it directly. However, 'command' is a shell-builtin command,
then Make would fail to find it in the PATH environment:
$ make ARCH=m68k defconfig
make: command: Command not found
make: command: Command not found
make: command: Command not found
In fact, Make has a table of shell-builtin commands because it must
ask the shell to execute them.
Until recently, 'command' was missing in the table.
This issue was fixed by the following commit:
| commit 1af314465e5dfe3e8baa839a32a72e83c04f26ef
| Author: Paul Smith <psmith@gnu.org>
| Date: Sun Nov 12 18:10:28 2017 -0500
|
| * job.c: Add "command" as a known shell built-in.
|
| This is not a POSIX shell built-in but it's common in UNIX shells.
| Reported by Nick Bowler <nbowler@draconx.ca>.
Because the latest release is GNU Make 4.2.1 in 2016, this commit is
not included in any released versions. (But some distributions may
have back-ported it.)
We need to trick Make to spawn a subshell. There are various ways to
do so:
1) Use a shell special character '~' as dummy
$(shell : ~; command -v $(c)gcc)
2) Use a variable reference that always expands to the empty string
(suggested by David Laight)
$(shell command$${x:+} -v $(c)gcc)
3) Use redirect
$(shell command -v $(c)gcc 2>/dev/null)
I chose 3) to not confuse people. The stderr would not be polluted
anyway, but it will provide extra safety, and is easy to understand.
Tested on Make 3.81, 3.82, 4.0, 4.1, 4.2, 4.2.1
[1] http://pubs.opengroup.org/onlinepubs/9699919799/utilities/command.html
Fixes: bd55f96fa9 ("kbuild: refactor cc-cross-prefix implementation")
Cc: linux-stable <stable@vger.kernel.org> # 5.1
Reported-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Alexey Brodkin <abrodkin@synopsys.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 315 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190115.503150771@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program file is free software you can redistribute it and or
modify it under the terms of the gnu general public license as
published by the free software foundation version 2 of the license
this program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details you should have received a
copy of the gnu general public license along with this program in a
file named copying if not write to the free software foundation inc
51 franklin street fifth floor boston ma 02110 1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531081038.017566012@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program file is free software you can redistribute it and or
modify it under the terms of the gnu general public license as
published by the free software foundation version 2 of the license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531081036.527324761@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following error occurs for the `make ARCH=arm64 checkstack` case:
aarch64-linux-gnu-objdump -d vmlinux $(find . -name '*.ko') | \
perl ./scripts/checkstack.pl arm64
wrong or unknown architecture "arm64"
As suggested by Masahiro Yamada, fix the above error using regular
expressions in the same way it was fixed for the `ARCH=x86` case via
commit fda9f9903b ("scripts/checkstack.pl: automatically handle
32-bit and 64-bit mode for ARCH=x86").
Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: George G. Davis <george_davis@mentor.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The buildtar script might want to invoke a make, so tell the parent
make to pass the jobserver token pipe to the subcommand by prefixing
the command with a +.
This addresses the issue seen here:
/bin/sh ../scripts/package/buildtar tar-pkg
make[3]: warning: jobserver unavailable: using -j1. Add '+' to parent make rule.
See https://www.gnu.org/software/make/manual/html_node/Job-Slots.html
for more information.
Signed-off-by: Trevor Bourget <tgb.kernel@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Adding SPDX license identifier is pretty safe; however, here is one
exception.
Since commit ec8f24b7fa ("treewide: Add SPDX license identifier -
Makefile/Kconfig"), "make testconfig" would not pass.
When Kconfig detects a circular file inclusion, it displays error
messages with a file name and a line number prefixed to each line.
The unit test checks if Kconfig emits the error messages correctly
(this also checks the line number correctness).
Now that the test input has the SPDX license identifier at the very top,
the line numbers in the expected stderr should be incremented by 1.
Fixes: ec8f24b7fa ("treewide: Add SPDX license identifier - Makefile/Kconfig")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Merge misc fixes from Andrew Morton:
"Various fixes and followups"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm, compaction: make sure we isolate a valid PFN
include/linux/generic-radix-tree.h: fix kerneldoc comment
kernel/signal.c: trace_signal_deliver when signal_group_exit
drivers/iommu/intel-iommu.c: fix variable 'iommu' set but not used
spdxcheck.py: fix directory structures
kasan: initialize tag to 0xff in __kasan_kmalloc
z3fold: fix sheduling while atomic
scripts/gdb: fix invocation when CONFIG_COMMON_CLK is not set
mm/gup: continue VM_FAULT_RETRY processing even for pre-faults
ocfs2: fix error path kobject memory leak
memcg: make it work on sparse non-0-node systems
mm, memcg: consider subtrees in memory.events
prctl_set_mm: downgrade mmap_sem to read lock
prctl_set_mm: refactor checks from validate_prctl_map
kernel/fork.c: make max_threads symbol static
arch/arm/boot/compressed/decompress.c: fix build error due to lz4 changes
arch/parisc/configs/c8000_defconfig: remove obsoleted CONFIG_DEBUG_SLAB_LEAK
mm/vmalloc.c: fix typo in comment
lib/sort.c: fix kernel-doc notation warnings
mm: fix Documentation/vm/hmm.rst Sphinx warnings
The LICENSE directory has recently changed structure and this makes
spdxcheck fails as per below:
FAIL: "Blob or Tree named 'other' not found"
Traceback (most recent call last):
File "scripts/spdxcheck.py", line 240, in <module>
spdx = read_spdxdata(repo)
File "scripts/spdxcheck.py", line 41, in read_spdxdata
for el in lictree[d].traverse():
[...]
KeyError: "Blob or Tree named 'other' not found"
Fix the script to restore the correctness on checkpatch License checking.
References: 62be257e98 ("LICENSES: Rename other to deprecated")
References: 8ea8814fcd ("LICENSES: Clearly mark dual license only licenses")
Link: http://lkml.kernel.org/r/20190523084755.56739-1-vincenzo.frascino@arm.com
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Joe Perches <joe@perches.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jeremy Cline <jcline@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull gcc-plugins fix from Kees Cook:
"Handle unusual header environment, fixing a redefined macro error
under a Darwin build host"
* tag 'gcc-plugins-v5.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
gcc-plugins: Fix build failures under Darwin host
Pull yet more SPDX updates from Greg KH:
"Here is another set of reviewed patches that adds SPDX tags to
different kernel files, based on a set of rules that are being used to
parse the comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review
and analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers"
* tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (82 commits)
treewide: Add SPDX license identifier - Kbuild
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 225
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 224
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 223
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 222
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 221
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 220
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 218
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 217
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 216
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 215
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 214
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 213
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 211
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 210
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 209
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 207
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 206
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 203
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 201
...
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1334 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull documentation fixes from Jonathan Corbet:
"The Sphinx 2.0 release contained a few incompatible API changes that
broke our extensions and, thus, the documentation build in general.
Who knew that those deprecation warnings it was outputting actually
meant we should change something? This set of fixes makes the build
work again with Sphinx 2.0 and eliminates the warnings for 1.8. As
part of that, we also need a few fixes to the docs for places where
the new Sphinx is more strict.
It is a bit late in the cycle for this kind of change, but it does fix
problems that people are experiencing now.
There has been some talk of raising the minimum version of Sphinx we
support. I don't want to do that abruptly, though, so these changes
add some glue to continue to support versions back to 1.3. We will be
adding some infrastructure soon to nudge users of old versions
forward, with the idea of maybe increasing our minimum version (and
removing this glue) sometime in the future"
* tag 'docs-5.2-fixes2' of git://git.lwn.net/linux:
drm/i915: Maintain consistent documentation subsection ordering
scripts/sphinx-pre-install: make it handle Sphinx versions
docs: Fix conf.py for Sphinx 2.0
docs: fix multiple doc build warnings in enumeration.rst
lib/list_sort: fix kerneldoc build error
docs: fix numaperf.rst and add it to the doc tree
doc: Cope with the deprecation of AutoReporter
doc: Cope with Sphinx logging deprecations
Pull Devicetree fixes from Rob Herring:
- Update checkpatch.pl to use DT vendor-prefixes.yaml
- Fix DT binding references to files converted to DT schema
- Clean-up Arm CPU binding examples to match schema
- Add Sifive block versioning scheme documentation
- Pass binding directory base to validation tools for reference lookups
* tag 'devicetree-fixes-for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
checkpatch.pl: Update DT vendor prefix check
dt: bindings: mtd: replace references to nand.txt with nand-controller.yaml
dt-bindings: interrupt-controller: arm,gic: Fix schema errors in example
dt-bindings: arm: Clean up CPU binding examples
dt: fix refs that were renamed to json with the same file name
dt-bindings: Pass binding directory to validation tools
dt-bindings: sifive: describe sifive-blocks versioning
Pule more SPDX updates from Greg KH:
"Here is another set of reviewed patches that adds SPDX tags to
different kernel files, based on a set of rules that are being used to
parse the comments to try to determine that the license of the file is
"GPL-2.0-or-later".
Only the "obvious" versions of these matches are included here, a
number of "non-obvious" variants of text have been found but those
have been postponed for later review and analysis.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers"
* tag 'spdx-5.2-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (85 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 125
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 123
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 122
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 121
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 120
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 119
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 118
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 116
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 114
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 113
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 112
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 111
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 110
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 106
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 105
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 104
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 103
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 102
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 101
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 98
...
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
675 mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 441 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520071858.739733335@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
