[ Upstream commit 505127068d ]
On systems where TM (Transactional Memory) is disabled the
tm-signal-sigreturn-nt test causes a SIGILL:
test: tm_signal_sigreturn_nt
tags: git_version:7c202575ef63
!! child died by signal 4
failure: tm_signal_sigreturn_nt
We should skip the test if TM is not available.
Fixes: 34642d70ac ("selftests/powerpc: Add checks for transactional sigreturn")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191104233524.24348-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a02cbc7ffe ]
Some of our TM (Transactional Memory) tests, list "r1" (the stack
pointer) as a clobbered register.
GCC >= 9 doesn't accept this, and the build breaks:
ptrace-tm-spd-tar.c: In function 'tm_spd_tar':
ptrace-tm-spd-tar.c:31:2: error: listing the stack pointer register 'r1' in a clobber list is deprecated [-Werror=deprecated]
31 | asm __volatile__(
| ^~~
ptrace-tm-spd-tar.c:31:2: note: the value of the stack pointer after an 'asm' statement must be the same as it was before the statement
We do have some fairly large inline asm blocks in these tests, and
some of them do change the value of r1. However they should all return
to C with the value in r1 restored, so I think it's legitimate to say
r1 is not clobbered.
As Segher points out, the r1 clobbers may have been added because of
the use of `or 1,1,1`, however that doesn't actually clobber r1.
Segher also points out that some of these tests do clobber LR, because
they call functions, and that is not listed in the clobbers, so add
that where appropriate.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191029095324.14669-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6dd504b0fd ]
This test only works when [1] is applied, which was rejected.
Basically, the errors are reported and cleared. In this particular case of
tls sockets, following reads will block.
The test case was originally submitted with the rejected patch, but, then,
was included as part of a different patchset, possibly by mistake.
[1] https://lore.kernel.org/netdev/20191007035323.4360-2-jakub.kicinski@netronome.com/#t
Thanks Paolo Pisati for pointing out the original patchset where this
appeared.
Fixes: 65190f7742 (selftests/tls: add a test for fragmented messages)
Reported-by: Paolo Pisati <paolo.pisati@canonical.com>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ea2612b98 ]
Currently, with latest llvm trunk, selftest test_progs failed obj
file test_seg6_loop.o with the following error in verifier:
infinite loop detected at insn 76
The byte code sequence looks like below, and noted that alu32 has been
turned off by default for better generated codes in general:
48: w3 = 100
49: *(u32 *)(r10 - 68) = r3
...
; if (tlv.type == SR6_TLV_PADDING) {
76: if w3 == 5 goto -18 <LBB0_19>
...
85: r1 = *(u32 *)(r10 - 68)
; for (int i = 0; i < 100; i++) {
86: w1 += -1
87: if w1 == 0 goto +5 <LBB0_20>
88: *(u32 *)(r10 - 68) = r1
The main reason for verification failure is due to partial spills at
r10 - 68 for induction variable "i".
Current verifier only handles spills with 8-byte values. The above 4-byte
value spill to stack is treated to STACK_MISC and its content is not
saved. For the above example:
w3 = 100
R3_w=inv100 fp-64_w=inv1086626730498
*(u32 *)(r10 - 68) = r3
R3_w=inv100 fp-64_w=inv1086626730498
...
r1 = *(u32 *)(r10 - 68)
R1_w=inv(id=0,umax_value=4294967295,var_off=(0x0; 0xffffffff))
fp-64=inv1086626730498
To resolve this issue, verifier needs to be extended to track sub-registers
in spilling, or llvm needs to enhanced to prevent sub-register spilling
in register allocation phase. The former will increase verifier complexity
and the latter will need some llvm "hacking".
Let us workaround this issue by declaring the induction variable as "long"
type so spilling will happen at non sub-register level. We can revisit this
later if sub-register spilling causes similar or other verification issues.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20191117214036.1309510-1-yhs@fb.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b054b7133 ]
When run_kselftests.sh is run, it hangs after test_tc_tunnel.sh. The reason
is test_tc_tunnel.sh ensures the server ('nc -l') is run all the time,
starting it again every time it is expected to terminate. The exception is
the final client_connect: the server is not started anymore, which ensures
no process is kept running after the test is finished.
For a sit test, though, the script is terminated prematurely without the
final client_connect and the 'nc' process keeps running. This in turn causes
the run_one function in kselftest/runner.sh to hang forever, waiting for the
runaway process to finish.
Ensure a remaining server is terminated on cleanup.
Fixes: f6ad6accaa ("selftests/bpf: expand test_tc_tunnel with SIT encap")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/bpf/60919291657a9ee89c708d8aababc28ebe1420be.1573821780.git.jbenc@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7a0d65d80 ]
With latest llvm compiler, running test_progs will have the following
verifier failure for test_sysctl_loop1.o:
libbpf: load bpf program failed: Permission denied
libbpf: -- BEGIN DUMP LOG ---
libbpf:
invalid indirect read from stack var_off (0x0; 0xff)+196 size 7
...
libbpf: -- END LOG --
libbpf: failed to load program 'cgroup/sysctl'
libbpf: failed to load object 'test_sysctl_loop1.o'
The related bytecode looks as below:
0000000000000308 LBB0_8:
97: r4 = r10
98: r4 += -288
99: r4 += r7
100: w8 &= 255
101: r1 = r10
102: r1 += -488
103: r1 += r8
104: r2 = 7
105: r3 = 0
106: call 106
107: w1 = w0
108: w1 += -1
109: if w1 > 6 goto -24 <LBB0_5>
110: w0 += w8
111: r7 += 8
112: w8 = w0
113: if r7 != 224 goto -17 <LBB0_8>
And source code:
for (i = 0; i < ARRAY_SIZE(tcp_mem); ++i) {
ret = bpf_strtoul(value + off, MAX_ULONG_STR_LEN, 0,
tcp_mem + i);
if (ret <= 0 || ret > MAX_ULONG_STR_LEN)
return 0;
off += ret & MAX_ULONG_STR_LEN;
}
Current verifier is not able to conclude that register w0 before '+'
at insn 110 has a range of 1 to 7 and thinks it is from 0 - 255. This
leads to more conservative range for w8 at insn 112, and later verifier
complaint.
Let us workaround this issue until we found a compiler and/or verifier
solution. The workaround in this patch is to make variable 'ret' volatile,
which will force a reload and then '&' operation to ensure better value
range. With this patch, I got the below byte code for the loop:
0000000000000328 LBB0_9:
101: r4 = r10
102: r4 += -288
103: r4 += r7
104: w8 &= 255
105: r1 = r10
106: r1 += -488
107: r1 += r8
108: r2 = 7
109: r3 = 0
110: call 106
111: *(u32 *)(r10 - 64) = r0
112: r1 = *(u32 *)(r10 - 64)
113: if w1 s< 1 goto -28 <LBB0_5>
114: r1 = *(u32 *)(r10 - 64)
115: if w1 s> 7 goto -30 <LBB0_5>
116: r1 = *(u32 *)(r10 - 64)
117: w1 &= 7
118: w1 += w8
119: r7 += 8
120: w8 = w1
121: if r7 != 224 goto -21 <LBB0_9>
Insn 117 did the '&' operation and we got more precise value range
for 'w8' at insn 120. The test is happy then:
#3/17 test_sysctl_loop1.o:OK
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20191107170045.2503480-1-yhs@fb.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 670cd6849e ]
Fix printf format warnings on arm (and other 32bit arch).
- udpgso.c and udpgso_bench_tx use %lu for size_t but it
should be unsigned long long on 32bit arch.
- so_txtime.c uses %ld for int64_t, but it should be
unsigned long long on 32bit arch.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Willem de Bruijn <willemb@google.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f3571ea71 ]
Currently proc-self-map-files-002.c sets va_max (max test address
of user virtual address) to 4GB, but it is too big for 32bit
arch and 1UL << 32 is overflow on 32bit long.
Also since this value should be enough bigger than vm.mmap_min_addr
(64KB or 32KB by default), 1MB should be enough.
Make va_max 1MB unconditionally.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c588146378 ]
The "path" buf is supposed to contain path + printf msg up to 24 bytes.
It will be cut anyway, but compiler generates truncation warns like:
"
samples/bpf/../../tools/testing/selftests/bpf/cgroup_helpers.c: In
function ‘setup_cgroup_environment’:
samples/bpf/../../tools/testing/selftests/bpf/cgroup_helpers.c:52:34:
warning: ‘/cgroup.controllers’ directive output may be truncated
writing 19 bytes into a region of size between 1 and 4097
[-Wformat-truncation=]
snprintf(path, sizeof(path), "%s/cgroup.controllers", cgroup_path);
^~~~~~~~~~~~~~~~~~~
samples/bpf/../../tools/testing/selftests/bpf/cgroup_helpers.c:52:2:
note: ‘snprintf’ output between 20 and 4116 bytes into a destination
of size 4097
snprintf(path, sizeof(path), "%s/cgroup.controllers", cgroup_path);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
samples/bpf/../../tools/testing/selftests/bpf/cgroup_helpers.c:72:34:
warning: ‘/cgroup.subtree_control’ directive output may be truncated
writing 23 bytes into a region of size between 1 and 4097
[-Wformat-truncation=]
snprintf(path, sizeof(path), "%s/cgroup.subtree_control",
^~~~~~~~~~~~~~~~~~~~~~~
cgroup_path);
samples/bpf/../../tools/testing/selftests/bpf/cgroup_helpers.c:72:2:
note: ‘snprintf’ output between 24 and 4120 bytes into a destination
of size 4097
snprintf(path, sizeof(path), "%s/cgroup.subtree_control",
cgroup_path);
"
In order to avoid warns, lets decrease buf size for cgroup workdir on
24 bytes with assumption to include also "/cgroup.subtree_control" to
the address. The cut will never happen anyway.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20191002120404.26962-3-ivan.khoronzhuk@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65cb139862 ]
When creating the second host in h2_create(), two addresses are assigned
to the interface, but only one is deleted. When running the test twice
in a row the following error is observed:
$ ./router_bridge_vlan.sh
TEST: ping [ OK ]
TEST: ping6 [ OK ]
TEST: vlan [ OK ]
$ ./router_bridge_vlan.sh
RTNETLINK answers: File exists
TEST: ping [ OK ]
TEST: ping6 [ OK ]
TEST: vlan [ OK ]
Fix this by deleting the address during cleanup.
Fixes: 5b1e7f9ebd ("selftests: forwarding: Test routed bridge interface")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 02bf1f8b3c ]
As per commit 131b30c94f ("kselftest: exclude failed TARGETS from
runlist") failed targets were excluded from the runlist. But value
$$INSTALL_PATH is always NULL. It should be $INSTALL_PATH instead
$$INSTALL_PATH.
So, fix Makefile to use $INSTALL_PATH.
Fixes: 131b30c94f ("kselftest: exclude failed TARGETS from runlist")
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2745aea675 ]
Some versions of iproute2 will output more than one line per entry, which
will cause the test to fail, like:
TEST: ipv6: list and flush cached exceptions [FAIL]
can't list cached exceptions
That happens, for example, with iproute2 4.15.0. When using the -oneline
option, this will work just fine:
TEST: ipv6: list and flush cached exceptions [ OK ]
This also works just fine with a more recent version of iproute2, like
5.4.0.
For some reason, two lines are printed for the IPv4 test no matter what
version of iproute2 is used. Use the same -oneline parameter there instead
of counting the lines twice.
Fixes: b964641e99 ("selftests: pmtu: Make list_flush_ipv6_exception test more demanding")
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Acked-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4d2fa82d98 upstream.
If the kernel accidentally uses DS or ES while the user values are
loaded, it will work fine for sane userspace. In the interest of
simulating maximally insane userspace, make sigreturn_32 zero out DS
and ES for the nasty parts so that inadvertent use of these segments
will crash.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8caa016bfc upstream.
For reasons that I haven't quite fully diagnosed, running
mov_ss_trap_32 on a 32-bit kernel results in an infinite loop in
userspace. This appears to be because the hacky SYSENTER test
doesn't segfault as desired; instead it corrupts the program state
such that it infinite loops.
Fix it by explicitly clearing EBP before doing SYSENTER. This will
give a more reliable segfault.
Fixes: 59c2a7226f ("x86/selftests: Add mov_to_ss test")
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull networking fixes from David Miller:
1) Fix memory leak in xfrm_state code, from Steffen Klassert.
2) Fix races between devlink reload operations and device
setup/cleanup, from Jiri Pirko.
3) Null deref in NFC code, from Stephan Gerhold.
4) Refcount fixes in SMC, from Ursula Braun.
5) Memory leak in slcan open error paths, from Jouni Hogander.
6) Fix ETS bandwidth validation in hns3, from Yonglong Liu.
7) Info leak on short USB request answers in ax88172a driver, from
Oliver Neukum.
8) Release mem region properly in ep93xx_eth, from Chuhong Yuan.
9) PTP config timestamp flags validation, from Richard Cochran.
10) Dangling pointers after SKB data realloc in seg6, from Andrea Mayer.
11) Missing free_netdev() in gemini driver, from Chuhong Yuan.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (56 commits)
ipmr: Fix skb headroom in ipmr_get_route().
net: hns3: cleanup of stray struct hns3_link_mode_mapping
net/smc: fix fastopen for non-blocking connect()
rds: ib: update WR sizes when bringing up connection
net: gemini: add missed free_netdev
net: dsa: tag_8021q: Fix dsa_8021q_restore_pvid for an absent pvid
seg6: fix skb transport_header after decap_and_validate()
seg6: fix srh pointer in get_srh()
net: stmmac: Use the correct style for SPDX License Identifier
octeontx2-af: Use the correct style for SPDX License Identifier
ptp: Extend the test program to check the external time stamp flags.
mlx5: Reject requests to enable time stamping on both edges.
igb: Reject requests that fail to enable time stamping on both edges.
dp83640: Reject requests to enable time stamping on both edges.
mv88e6xxx: Reject requests to enable time stamping on both edges.
ptp: Introduce strict checking of external time stamp options.
renesas: reject unsupported external timestamp flags
mlx5: reject unsupported external timestamp flags
igb: reject unsupported external timestamp flags
dp83640: reject unsupported external timestamp flags
...
Because each driver and hardware has different capabilities, the test
cannot provide a simple pass/fail result, but it can at least show what
combinations of flags are supported.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw does not support VXLAN devices with a physical device attached and
vetoes such configurations upon enslavement to an offloaded bridge.
Commit 0ce1822c2a ("vxlan: add adjacent link to limit depth level")
changed the VXLAN device to be an upper of the physical device which
causes mlxsw to veto the creation of the VXLAN device with "Unknown
upper device type".
This is OK as this configuration is not supported, but it prevents us
from testing bad flows involving the enslavement of VXLAN devices with a
physical device to a bridge, regardless if the physical device is an
mlxsw netdev or not.
Adjust the test to use a dummy device as a physical device instead of a
mlxsw netdev.
Fixes: 0ce1822c2a ("vxlan: add adjacent link to limit depth level")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) BPF sample build fixes from Björn Töpel
2) Fix powerpc bpf tail call implementation, from Eric Dumazet.
3) DCCP leaks jiffies on the wire, fix also from Eric Dumazet.
4) Fix crash in ebtables when using dnat target, from Florian Westphal.
5) Fix port disable handling whne removing bcm_sf2 driver, from Florian
Fainelli.
6) Fix kTLS sk_msg trim on fallback to copy mode, from Jakub Kicinski.
7) Various KCSAN fixes all over the networking, from Eric Dumazet.
8) Memory leaks in mlx5 driver, from Alex Vesker.
9) SMC interface refcounting fix, from Ursula Braun.
10) TSO descriptor handling fixes in stmmac driver, from Jose Abreu.
11) Add a TX lock to synchonize the kTLS TX path properly with crypto
operations. From Jakub Kicinski.
12) Sock refcount during shutdown fix in vsock/virtio code, from Stefano
Garzarella.
13) Infinite loop in Intel ice driver, from Colin Ian King.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (108 commits)
ixgbe: need_wakeup flag might not be set for Tx
i40e: need_wakeup flag might not be set for Tx
igb/igc: use ktime accessors for skb->tstamp
i40e: Fix for ethtool -m issue on X722 NIC
iavf: initialize ITRN registers with correct values
ice: fix potential infinite loop because loop counter being too small
qede: fix NULL pointer deref in __qede_remove()
net: fix data-race in neigh_event_send()
vsock/virtio: fix sock refcnt holding during the shutdown
net: ethernet: octeon_mgmt: Account for second possible VLAN header
mac80211: fix station inactive_time shortly after boot
net/fq_impl: Switch to kvmalloc() for memory allocation
mac80211: fix ieee80211_txq_setup_flows() failure path
ipv4: Fix table id reference in fib_sync_down_addr
ipv6: fixes rt6_probe() and fib6_nh->last_probe init
net: hns: Fix the stray netpoll locks causing deadlock in NAPI path
net: usb: qmi_wwan: add support for DW5821e with eSIM support
CDC-NCM: handle incomplete transfer of MTU
nfc: netlink: fix double device reference drop
NFC: st21nfca: fix double free
...
The MAP_HUGETLB ("-H" option) of gup_benchmark fails:
$ sudo ./gup_benchmark -H
mmap: Invalid argument
This is because gup_benchmark.c is passing in a file descriptor to
mmap(), but the fd came from opening up the /dev/zero file. This
confuses the mmap syscall implementation, which thinks that, if the
caller did not specify MAP_ANONYMOUS, then the file must be a huge page
file. So it attempts to verify that the file really is a huge page
file, as you can see here:
ksys_mmap_pgoff()
{
if (!(flags & MAP_ANONYMOUS)) {
retval = -EINVAL;
if (unlikely(flags & MAP_HUGETLB && !is_file_hugepages(file)))
goto out_fput; /* THIS IS WHERE WE END UP */
else if (flags & MAP_HUGETLB) {
...proceed normally, /dev/zero is ok here...
...and of course is_file_hugepages() returns "false" for the /dev/zero
file.
The problem is that the user space program, gup_benchmark.c, really just
wants anonymous memory here. The simplest way to get that is to pass
MAP_ANONYMOUS whenever MAP_HUGETLB is specified, so that's what this
patch does.
Link: http://lkml.kernel.org/r/20191021212435.398153-2-jhubbard@nvidia.com
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Jérôme Glisse <jglisse@redhat.com>
Cc: Keith Busch <keith.busch@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Daniel Borkmann says:
====================
pull-request: bpf 2019-11-02
The following pull-request contains BPF updates for your *net* tree.
We've added 6 non-merge commits during the last 6 day(s) which contain
a total of 8 files changed, 35 insertions(+), 9 deletions(-).
The main changes are:
1) Fix ppc BPF JIT's tail call implementation by performing a second pass
to gather a stable JIT context before opcode emission, from Eric Dumazet.
2) Fix build of BPF samples sys_perf_event_open() usage to compiled out
unavailable test_attr__{enabled,open} checks. Also fix potential overflows
in bpf_map_{area_alloc,charge_init} on 32 bit archs, from Björn Töpel.
3) Fix narrow loads of bpf_sysctl context fields with offset > 0 on big endian
archs like s390x and also improve the test coverage, from Ilya Leoshkevich.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix free/alloc races in batmanadv, from Sven Eckelmann.
2) Several leaks and other fixes in kTLS support of mlx5 driver, from
Tariq Toukan.
3) BPF devmap_hash cost calculation can overflow on 32-bit, from Toke
Høiland-Jørgensen.
4) Add an r8152 device ID, from Kazutoshi Noguchi.
5) Missing include in ipv6's addrconf.c, from Ben Dooks.
6) Use siphash in flow dissector, from Eric Dumazet. Attackers can
easily infer the 32-bit secret otherwise etc.
7) Several netdevice nesting depth fixes from Taehee Yoo.
8) Fix several KCSAN reported errors, from Eric Dumazet. For example,
when doing lockless skb_queue_empty() checks, and accessing
sk_napi_id/sk_incoming_cpu lockless as well.
9) Fix jumbo packet handling in RXRPC, from David Howells.
10) Bump SOMAXCONN and tcp_max_syn_backlog values, from Eric Dumazet.
11) Fix DMA synchronization in gve driver, from Yangchun Fu.
12) Several bpf offload fixes, from Jakub Kicinski.
13) Fix sk_page_frag() recursion during memory reclaim, from Tejun Heo.
14) Fix ping latency during high traffic rates in hisilicon driver, from
Jiangfent Xiao.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (146 commits)
net: fix installing orphaned programs
net: cls_bpf: fix NULL deref on offload filter removal
selftests: bpf: Skip write only files in debugfs
selftests: net: reuseport_dualstack: fix uninitalized parameter
r8169: fix wrong PHY ID issue with RTL8168dp
net: dsa: bcm_sf2: Fix IMP setup for port different than 8
net: phylink: Fix phylink_dbg() macro
gve: Fixes DMA synchronization.
inet: stop leaking jiffies on the wire
ixgbe: Remove duplicate clear_bit() call
Documentation: networking: device drivers: Remove stray asterisks
e1000: fix memory leaks
i40e: Fix receive buffer starvation for AF_XDP
igb: Fix constant media auto sense switching when no cable is connected
net: ethernet: arc: add the missed clk_disable_unprepare
igb: Enable media autosense for the i350.
igb/igc: Don't warn on fatal read failures when the device is removed
tcp: increase tcp_max_syn_backlog max value
net: increase SOMAXCONN to 4096
netdevsim: Fix use-after-free during device dismantle
...
DebugFS for netdevsim now contains some "action trigger" files
which are write only. Don't try to capture the contents of those.
Note that we can't use os.access() because the script requires
root.
Fixes: 4418f862d6 ("netdevsim: implement support for devlink region and snapshots")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This test reports EINVAL for getsockopt(SOL_SOCKET, SO_DOMAIN)
occasionally due to the uninitialized length parameter.
Initialize it to fix this, and also use int for "test_family" to comply
with the API standard.
Fixes: d6a61f80b8 ("soreuseport: test mixed v4/v6 sockets")
Reported-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Cc: Craig Gallek <cgallek@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"ctx:file_pos sysctl:read read ok narrow" works on s390 by accident: it
reads the wrong byte, which happens to have the expected value of 0.
Improve the test by seeking to the 4th byte and expecting 4 instead of
0.
This makes the latent problem apparent: the test attempts to read the
first byte of bpf_sysctl.file_pos, assuming this is the least-significant
byte, which is not the case on big-endian machines: a non-zero offset is
needed.
The point of the test is to verify narrow loads, so we cannot cheat our
way out by simply using BPF_W. The existence of the test means that such
loads have to be supported, most likely because llvm can generate them.
Fix the test by adding a big-endian variant, which uses an offset to
access the least-significant byte of bpf_sysctl.file_pos.
This reveals the final problem: verifier rejects accesses to bpf_sysctl
fields with offset > 0. Such accesses are already allowed for a wide
range of structs: __sk_buff, bpf_sock_addr and sk_msg_md to name a few.
Extend this support to bpf_sysctl by using bpf_ctx_range instead of
offsetof when matching field offsets.
Fixes: 7b146cebe3 ("bpf: Sysctl hook")
Fixes: e1550bfe0d ("bpf: Add file_pos field to bpf_sysctl ctx")
Fixes: 9a1027e525 ("selftests/bpf: Test file_pos field in bpf_sysctl ctx")
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrey Ignatov <rdna@fb.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20191028122902.9763-1-iii@linux.ibm.com
Daniel Borkmann says:
====================
pull-request: bpf 2019-10-27
The following pull-request contains BPF updates for your *net* tree.
We've added 7 non-merge commits during the last 11 day(s) which contain
a total of 7 files changed, 66 insertions(+), 16 deletions(-).
The main changes are:
1) Fix two use-after-free bugs in relation to RCU in jited symbol exposure to
kallsyms, from Daniel Borkmann.
2) Fix NULL pointer dereference in AF_XDP rx-only sockets, from Magnus Karlsson.
3) Fix hang in netdev unregister for hash based devmap as well as another overflow
bug on 32 bit archs in memlock cost calculation, from Toke Høiland-Jørgensen.
4) Fix wrong memory access in LWT BPF programs on reroute due to invalid dst.
Also fix BPF selftests to use more compatible nc options, from Jiri Benc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds two more tests to ipv4_addr_metric_test() to
explicitly cover the scenarios fixed by the previous patch.
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kernel test robot reported that the l2tp.sh test script failed:
# selftests: net: l2tp.sh
# Warning: file l2tp.sh is not executable, correct this.
Set executable bits.
Fixes: e858ef1cd4 ("selftests: Add l2tp tests")
Reported-by: kernel test robot <rong.a.chen@intel.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Commit 204c91eff7 ("KVM: selftests: do not blindly clobber registers in
guest asm") was intended to make test more gcc-proof, however, the result
is exactly the opposite: on newer gccs (e.g. 8.2.1) the test breaks with
==== Test Assertion Failure ====
x86_64/sync_regs_test.c:168: run->s.regs.regs.rbx == 0xBAD1DEA + 1
pid=14170 tid=14170 - Invalid argument
1 0x00000000004015b3: main at sync_regs_test.c:166 (discriminator 6)
2 0x00007f413fb66412: ?? ??:0
3 0x000000000040191d: _start at ??:?
rbx sync regs value incorrect 0x1.
Apparently, compile is still free to play games with registers even
when they have variables attached.
Re-write guest code with 'asm volatile' by embedding ucall there and
making sure rbx is preserved.
Fixes: 204c91eff7 ("KVM: selftests: do not blindly clobber registers in guest asm")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
vmx_dirty_log_test fails on AMD and this is no surprise as it is VMX
specific. Bail early when nested VMX is unsupported.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
vmx_* tests require VMX and three of them implement the same check. Move it
to vmx library.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
vmx_set_nested_state_test() checks if VMX is supported twice: in the very
beginning (and skips the whole test if it's not) and before doing
test_vmx_nested_state(). One should be enough.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pull networking fixes from David Miller:
"I was battling a cold after some recent trips, so quite a bit piled up
meanwhile, sorry about that.
Highlights:
1) Fix fd leak in various bpf selftests, from Brian Vazquez.
2) Fix crash in xsk when device doesn't support some methods, from
Magnus Karlsson.
3) Fix various leaks and use-after-free in rxrpc, from David Howells.
4) Fix several SKB leaks due to confusion of who owns an SKB and who
should release it in the llc code. From Eric Biggers.
5) Kill a bunc of KCSAN warnings in TCP, from Eric Dumazet.
6) Jumbo packets don't work after resume on r8169, as the BIOS resets
the chip into non-jumbo mode during suspend. From Heiner Kallweit.
7) Corrupt L2 header during MPLS push, from Davide Caratti.
8) Prevent possible infinite loop in tc_ctl_action, from Eric
Dumazet.
9) Get register bits right in bcmgenet driver, based upon chip
version. From Florian Fainelli.
10) Fix mutex problems in microchip DSA driver, from Marek Vasut.
11) Cure race between route lookup and invalidation in ipv4, from Wei
Wang.
12) Fix performance regression due to false sharing in 'net'
structure, from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (145 commits)
net: reorder 'struct net' fields to avoid false sharing
net: dsa: fix switch tree list
net: ethernet: dwmac-sun8i: show message only when switching to promisc
net: aquantia: add an error handling in aq_nic_set_multicast_list
net: netem: correct the parent's backlog when corrupted packet was dropped
net: netem: fix error path for corrupted GSO frames
macb: propagate errors when getting optional clocks
xen/netback: fix error path of xenvif_connect_data()
net: hns3: fix mis-counting IRQ vector numbers issue
net: usb: lan78xx: Connect PHY before registering MAC
vsock/virtio: discard packets if credit is not respected
vsock/virtio: send a credit update when buffer size is changed
mlxsw: spectrum_trap: Push Ethernet header before reporting trap
net: ensure correct skb->tstamp in various fragmenters
net: bcmgenet: reset 40nm EPHY on energy detect
net: bcmgenet: soft reset 40nm EPHYs before MAC init
net: phy: bcm7xxx: define soft_reset for 40nm EPHY
net: bcmgenet: don't set phydev->link from MAC
net: Update address for MediaTek ethernet driver in MAINTAINERS
ipv4: fix race condition between route lookup and invalidation
...
Pull powerpc fixes from Michael Ellerman:
"Fix a kernel crash in spufs_create_root() on Cell machines, since the
new mount API went in.
Fix a regression in our KVM code caused by our recent PCR changes.
Avoid a warning message about a failing hypervisor API on systems that
don't have that API.
A couple of minor build fixes.
Thanks to: Alexey Kardashevskiy, Alistair Popple, Desnes A. Nunes do
Rosario, Emmanuel Nicolet, Jordan Niethe, Laurent Dufour, Stephen
Rothwell"
* tag 'powerpc-5.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
spufs: fix a crash in spufs_create_root()
powerpc/kvm: Fix kvmppc_vcore->in_guest value in kvmhv_switch_to_host
selftests/powerpc: Fix compile error on tlbie_test due to newer gcc
powerpc/pseries: Remove confusing warning message.
powerpc/64s/radix: Fix build failure with RADIX_MMU=n
Alexei Starovoitov says:
====================
pull-request: bpf 2019-10-12
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) a bunch of small fixes. Nothing critical.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer versions of GCC (>= 9) demand that the size of the string to be
copied must be explicitly smaller than the size of the destination.
Thus, the NULL char has to be taken into account on strncpy.
This will avoid the following compiling error:
tlbie_test.c: In function 'main':
tlbie_test.c:639:4: error: 'strncpy' specified bound 100 equals destination size
strncpy(logdir, optarg, LOGDIR_NAME_SIZE);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Desnes A. Nunes do Rosario <desnesn@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191003211010.9711-1-desnesn@linux.ibm.com
Pull Kselftest fixes from Shuah Khan:
"Fixes for existing tests and the framework.
Cristian Marussi's patches add the ability to skip targets (tests) and
exclude tests that didn't build from run-list. These patches improve
the Kselftest results. Ability to skip targets helps avoid running
tests that aren't supported in certain environments. As an example,
bpf tests from mainline aren't supported on stable kernels and have
dependency on bleeding edge llvm. Being able to skip bpf on systems
that can't meet this llvm dependency will be helpful.
Kselftest can be built and installed from the main Makefile. This
change help simplify Kselftest use-cases which addresses request from
users.
Kees Cook added per test timeout support to limit individual test
run-time"
* tag 'linux-kselftest-5.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: watchdog: Add command line option to show watchdog_info
selftests: watchdog: Validate optional file argument
selftests/kselftest/runner.sh: Add 45 second timeout per test
kselftest: exclude failed TARGETS from runlist
kselftest: add capability to skip chosen TARGETS
selftests: Add kselftest-all and kselftest-install targets
