commit 33a7ab91d5 upstream.
The W83L786NG stores the fan speed on 4 bits while the sysfs interface
uses a 0-255 range. Thus the driver should scale the user input down
to map it to the device range, and scale up the value read from the
device before presenting it to the user. The reserved register nibble
should be left unchanged.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf7559bc05 upstream.
The wrong mask is used, which causes some fan speed control modes
(pwmX_enable) to be incorrectly reported, and some modes to be
impossible to set.
[JD: add subject and description.]
Signed-off-by: Brian Carnes <bmcarnes@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit efabcc2123 upstream.
Some I2C bus drivers do not allow zero-length data transfers which are
required to start a measurement with the HIH6130/1 sensor. Nevertheless,
we can overcome this limitation by writing a zero dummy byte. This byte
is ignored by the sensor and was verified to be working with the OMAP
I2C bus driver in a BeagleBone board.
Signed-off-by: José Miguel Gonçalves <jose.goncalves@inov.pt>
[Guenter Roeck: Simplified complexity of write_length initialization]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e41fae2b1e upstream.
Bit 2 of status register 2 on MAX6696 (external diode 2 open)
sets ALERT; the bit thus has to be listed in alert_alarms.
Also display a message in the alert handler if the condition
is encountered.
Even though not all overtemperature conditions cause ALERT
to be set, we should not ignore them in the alert handler.
Display messages for all out-of-range conditions.
Reported-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 25f2bd7f5a upstream.
The crash reported and investigated in commit 5f4513 turned out to be
caused by a change to the read interface on newer (2012) SMCs.
Tests by Chris show that simply reading the data valid line is enough
for the problem to go away. Additional tests show that the newer SMCs
no longer wait for the number of requested bytes, but start sending
data right away. Apparently the number of bytes to read is no longer
specified as before, but instead found out by reading until end of
data. Failure to read until end of data confuses the state machine,
which eventually causes the crash.
As a remedy, assuming bit0 is the read valid line, make sure there is
nothing more to read before leaving the read function.
Tested to resolve the original problem, and runtested on MBA3,1,
MBP4,1, MBP8,2, MBP10,1, MBP10,2. The patch seems to have no effect on
machines before 2012.
Tested-by: Chris Murphy <chris@cmurf.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f45138643 upstream.
After reports from Chris and Josh Boyer of a rare crash in applesmc,
Guenter pointed at the initialization problem fixed below. The patch
has not been verified to fix the crash, but should be applied
regardless.
Reported-by: <jwboyer@fedoraproject.org>
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93d783bcca upstream.
In adt7470_write_word_data(), which writes two bytes using
i2c_smbus_write_byte_data(), the return codes are incorrectly AND-ed
together when they should be OR-ed together.
The return code of i2c_smbus_write_byte_data() is zero for success.
The upshot is only the first byte was ever written to the hardware.
The 2nd byte was never written out.
I noticed that trying to set the fan speed limits was not working
correctly on my system. Setting the fan speed limits is the only
code that uses adt7470_write_word_data(). After making the change
the limit settings work and the alarms work also.
Signed-off-by: Curt Brune <curt@cumulusnetworks.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1d2bff6a6 upstream.
Driver displays wrong alarms for temperature attributes.
Turns out that temperature alarm bits are not fixed, but determined
by temperature source mapping. To fix the problem, walk through
the temperature sources to determine the correct alarm bit associated
with a given attribute.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On a system with both MAX1617 and JC42 sensors, JC42 sensors can be misdetected
as LM84. Strengthen detection sufficiently enough to avoid this misdetection.
Also improve detection for ADM1021.
Modeled after chip detection code in sensors-detect command.
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
time_after (as opposed to time_after_equal) already ensures that the
cache lifetime is at least as much as requested. There is no point in
manually adding another jiffy to that value, and this can confuse the
reader into wrong interpretation.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch fixes the null pointer dereference in goto error_release_channels
path when allocate memory for st fails.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Overtemperature and hysteresis registers only exist for primary
temperature registers, not for alternates, so do not assign
those registers when initializing alternates.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull hwmon update from Jean Delvare:
"Only lm75 driver updates this time"
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (lm75) Add support for the Dallas/Maxim DS7505
hwmon: (lm75) Tune resolution and sample time per chip
hwmon: (lm75) Prepare to support per-chip resolution and sample time
hwmon: (lm75) Per-chip configuration register initialization
Basically it's the same as the original DS75 but much faster.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Most LM75-compatible chips can either sample much faster or with a
much better resolution than the original LM75 chip. So far the lm75
driver did not let the user take benefit of these improvements. Do it
now.
I decided to almost always configure the chip to use the best
resolution possible, which also means the longest sample time. The
only chips for which I didn't are the DS75, DS1775 and STDS75, because
they are really too slow in 12-bit mode (1.2 to 1.5 second worst case)
so I went for 11-bit mode as a more reasonable tradeoff. This choice is
dictated by the fact that the hwmon subsystem is meant for system
monitoring, it has never been supposed to be ultra-fast, and as a
matter of fact we do cache the sampled values in almost all drivers.
If anyone isn't pleased with these default settings, they can always
introduce a platform data structure or DT support for the lm75. That
being said, it seems nobody ever complained that the driver wouldn't
refresh the value faster than every 1.5 second, and the change made
it faster for all chips even in 12-bit mode, so I don't expect any
complaint.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Prepare the lm75 driver to support per-chip resolution and sample
time. For now we only make the code generic enough to support it, but
we still use the same, unchanged resolution (9-bit) and sample time
(1.5 s) for all chips.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
There is no standard for the configuration register bits of LM75-like
chips. We shouldn't blindly clear bits setting the resolution as they
are either unused or used for something else on some of the supported
chips.
So, switch to per-chip configuration initialization. This will allow
for better tuning later, for example using more resolution bits when
available.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Pull battery updates from Anton Vorontsov:
"Highlights:
- OpenFirmware/DeviceTree support for the Power Supply core: the core
now automatically populates supplied_from hierarchy from the device
tree. With these patches chargers and batteries can now lookup
each other without the board files support shim. Rhyland Klein at
NVIDIA did the work
- New ST-Ericsson ABX500 hwmon driver. The driver is heavily using
the AB85xx core and depends on some recent changes to it, so that
is why the driver comes through the battery tree. It has an
appropriate ack from the hwmon maintainer (i.e. Guenter Roeck).
Martin Persson at ST-Ericsson and Hongbo Zhang at Linaro authored
the driver
- Final bits to sync AB85xx ST-Ericsson changes into mainline. The
changes touch mfd parts, but these were acked by the appropriate
MFD maintainer (ie Samuel Ortiz). Lee Jones at Linaro did most of
the work and lead the submission process.
Minor changes, but still worth mentioning:
- Battery temperature reporting fix for Nokia N900 phones
- Versatile Express poweroff driver moved into drivers/power/reset/
- Tree-wide: use devm_kzalloc() where appropriate
- Tree-wide: dev_pm_ops cleanups/fixes"
* tag 'for-v3.10' of git://git.infradead.org/battery-2.6: (112 commits)
pm2301-charger: Fix suspend/resume
charger-manager: Use kmemdup instead of kzalloc + memcpy
power_supply: Populate supplied_from hierarchy from the device tree
power_supply: Add core support for supplied_from
power_supply: Define Binding for power-supplies
rx51_battery: Fix reporting temperature
hwmon: Add ST-Ericsson ABX500 hwmon driver
ab8500_bmdata: Export abx500_res_to_temp tables for hwmon
ab8500_{bmdata,fg}: Add const attributes to some data arrays
ab8500_bmdata: Eliminate CamelCase warning of some variables
ab8500_btemp: Make ab8500_btemp_get* interfaces public
goldfish_battery: Use resource_size()
lp8788-charger: Use PAGE_SIZE for the sysfs read operation
max8925_power: Use devm_kzalloc()
da9030_battery: Use devm_kzalloc()
da9052-battery: Use devm_kzalloc()
ds2760_battery: Use devm_kzalloc()
ds2780_battery: Use devm_kzalloc()
gpio-charger: Use devm_kzalloc()
isp1704_charger: Use devm_kzalloc()
...
Pull staging driver tree update from Greg Kroah-Hartman:
"Here's the big staging driver tree update for 3.10-rc1
This update contains loads of comedi driver cleanups and fixes in
here, iio updates, android driver changes, and other various staging
driver cleanups.
Thanks to some drivers being removed, and the comedi driver cleanups,
we have removed more code than we added:
627 files changed, 65145 insertions(+), 76321 deletions(-)
which is always nice to see.
All of these have been in linux-next for a while."
* tag 'staging-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (940 commits)
staging: comedi: ni_labpc: fix legacy driver build
staging: comedi: das800: cleanup the cio-das802/16 fifo comments
staging: comedi: das800: rename CamelCase vars in das800_ai_do_cmd()
staging: comedi: das800: tidy up the private data
staging: comedi: das800: tidy up das800_interrupt()
staging: comedi: das800: tidy up das800_ai_insn_read()
staging: comedi: das800: tidy up das800_di_insn_bits()
staging: comedi: das800: tidy up das800_do_insn_bits()
staging: comedi: das800: remove extra divisor calculation call
staging: comedi: das800: rename {enable,disable}_das800
staging: comedi: das800: tidy up subdevice init
staging: comedi: das800: allow attaching without interrupt support
staging: comedi: das800: interrupts are required for async command support
staging: comedi: das800: tidy up das800_ai_do_cmdtest()
staging: comedi: das800: remove 'volatile' on private data variables
staging: comedi: das800: cleanup the boardinfo
staging: comedi: das800: cleanup range table declarations
staging: comedi: das800: introduce das800_ind_{write, read}()
staging: comedi: das800: remove forward declarations
staging: comedi: das800: move das800_set_frequency()
...
TMP432 is similar to TMP431 with a second external temperature sensor.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cached data is no longer valid after resetting the temperature history.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Use two-dimensional array pointing to registers
Merge temperature and limit access functions into a single function
Return error codes from I2C reads
Use DIV_ROUND_CLOSEST for rounding operations and improve rounding
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Each of ST-Ericsson X500 chip set series consists of both ABX500 and DBX500
chips. This is ABX500 hwmon driver, where the abx500.c is a common layer for
all ABX500s, and the ab8500.c is specific for AB8500 chip. Under this designed
structure, other chip specific files can be added simply using the same common
layer abx500.c.
Signed-off-by: Hongbo Zhang <hongbo.zhang@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
This ensures that the loop iterations are correct even if/when
the number of elements in an array changes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Per datasheet, VIN3 and AUXTIN share the same external pin. However, there
is no clean way to detect this condition. Furthermore, both are reported
by the BIOS on Supermicro C7H61. It may thus be possible that chip revisions
exist where both attributes are supported at the same time.
Better play safe and report both.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NCT6775, NCT6776, and NCT6779 have a number of variants with the same
chip ID but different chip labels. Add text "or compatible" to the
message displayed when the driver is loaded and rephrase the Kconfig
entry to reflect that it also supports compatible chips.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Turns out that TMP411B and TMP411C have different and unique device IDs.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
TMP431 is compatible to TMP401.
Also add support for additional I2C addresses supported by TMP411B
and TMP411C.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Initialize device specific coefficients from table instead of hard-coding it
to simplify adding additional chips.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Limits on all supported sensors and chips have to be within 0..0x0fff,
and limits are always positive.
Clamp written values in chip driver. Also clear value cache to ensure
that the actually written value is read back and reported correctly.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
So far the driver reported the voltage on VAUX as "vout2". This was not
entirely appropriate as it is not an output voltage, and complicates
the code. Use the new virtual "VMON" register set and report the voltage
as "vmon" instead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Simplify the code and reduce its size by using is_visible to determine
valid attributes, and sysfs_create_group to create all of them with
a single call.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
