[ Upstream commit 12663bfc97 ]
unix_dgram_recvmsg() will hold the readlock of the socket until recv
is complete.
In the same time, we may try to setsockopt(SO_PEEK_OFF) which will hang until
unix_dgram_recvmsg() will complete (which can take a while) without allowing
us to break out of it, triggering a hung task spew.
Instead, allow set_peek_off to fail, this way userspace will not hang.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d323e92cc3 ]
maxattr in genl_family should be used to save the max attribute
type, but not the max command type. Drop monitor doesn't support
any attributes, so we should leave it as zero.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3868204d6b ]
commit a553e4a631 ("[PKTGEN]: IPSEC support")
tried to support IPsec ESP transport transformation for pktgen, but acctually
this doesn't work at all for two reasons(The orignal transformed packet has
bad IPv4 checksum value, as well as wrong auth value, reported by wireshark)
- After transpormation, IPv4 header total length needs update,
because encrypted payload's length is NOT same as that of plain text.
- After transformation, IPv4 checksum needs re-caculate because of payload
has been changed.
With this patch, armmed pktgen with below cofiguration, Wireshark is able to
decrypted ESP packet generated by pktgen without any IPv4 checksum error or
auth value error.
pgset "flag IPSEC"
pgset "flows 1"
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d2615bf450 ]
The following commit:
b6c40d68ff
net: only invoke dev->change_rx_flags when device is UP
tried to fix a problem with VLAN devices and promiscuouse flag setting.
The issue was that VLAN device was setting a flag on an interface that
was down, thus resulting in bad promiscuity count.
This commit blocked flag propagation to any device that is currently
down.
A later commit:
deede2fabe
vlan: Don't propagate flag changes on down interfaces
fixed VLAN code to only propagate flags when the VLAN interface is up,
thus fixing the same issue as above, only localized to VLAN.
The problem we have now is that if we have create a complex stack
involving multiple software devices like bridges, bonds, and vlans,
then it is possible that the flags would not propagate properly to
the physical devices. A simple examle of the scenario is the
following:
eth0----> bond0 ----> bridge0 ---> vlan50
If bond0 or eth0 happen to be down at the time bond0 is added to
the bridge, then eth0 will never have promisc mode set which is
currently required for operation as part of the bridge. As a
result, packets with vlan50 will be dropped by the interface.
The only 2 devices that implement the special flag handling are
VLAN and DSA and they both have required code to prevent incorrect
flag propagation. As a result we can remove the generic solution
introduced in b6c40d68ff and leave
it to the individual devices to decide whether they will block
flag propagation or not.
Reported-by: Stefan Priebe <s.priebe@profihost.ag>
Suggested-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6aafeef03b ]
Pushing original fragments through causes several problems. For example
for matching, frags may not be matched correctly. Take following
example:
<example>
On HOSTA do:
ip6tables -I INPUT -p icmpv6 -j DROP
ip6tables -I INPUT -p icmpv6 -m icmp6 --icmpv6-type 128 -j ACCEPT
and on HOSTB you do:
ping6 HOSTA -s2000 (MTU is 1500)
Incoming echo requests will be filtered out on HOSTA. This issue does
not occur with smaller packets than MTU (where fragmentation does not happen)
</example>
As was discussed previously, the only correct solution seems to be to use
reassembled skb instead of separete frags. Doing this has positive side
effects in reducing sk_buff by one pointer (nfct_reasm) and also the reams
dances in ipvs and conntrack can be removed.
Future plan is to remove net/ipv6/netfilter/nf_conntrack_reasm.c
entirely and use code in net/ipv6/reassembly.c instead.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f3d3342602 ]
This patch now always passes msg->msg_namelen as 0. recvmsg handlers must
set msg_namelen to the proper size <= sizeof(struct sockaddr_storage)
to return msg_name to the user.
This prevents numerous uninitialized memory leaks we had in the
recvmsg handlers and makes it harder for new code to accidentally leak
uninitialized memory.
Optimize for the case recvfrom is called with NULL as address. We don't
need to copy the address at all, so set it to NULL before invoking the
recvmsg handler. We can do so, because all the recvmsg handlers must
cope with the case a plain read() is called on them. read() also sets
msg_name to NULL.
Also document these changes in include/linux/net.h as suggested by David
Miller.
Changes since RFC:
Set msg->msg_name = NULL if user specified a NULL in msg_name but had a
non-null msg_namelen in verify_iovec/verify_compat_iovec. This doesn't
affect sendto as it would bail out earlier while trying to copy-in the
address. It also more naturally reflects the logic by the callers of
verify_iovec.
With this change in place I could remove "
if (!uaddr || msg_sys->msg_namelen == 0)
msg->msg_name = NULL
".
This change does not alter the user visible error logic as we ignore
msg_namelen as long as msg_name is NULL.
Also remove two unnecessary curly brackets in ___sys_recvmsg and change
comments to netdev style.
Cc: David Miller <davem@davemloft.net>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 13eb2ab2d3 ]
When trying to delete a table >= 256 using iproute2 the local table
will be deleted.
The table id is specified as a netlink attribute when it needs more then
8 bits and iproute2 then sets the table field to RT_TABLE_UNSPEC (0).
Preconditions to matching the table id in the rule delete code
doesn't seem to take the "table id in netlink attribute" into condition
so the frh_get_table helper function never gets to do its job when
matching against current rule.
Use the helper function twice instead of peaking at the table value directly.
Originally reported at: http://bugs.debian.org/724783
Reported-by: Nicolas HICHER <nhicher@avencall.com>
Signed-off-by: Andreas Henriksson <andreas@fatal.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cb03db9d0e ]
net_secret() is only used when CONFIG_IPV6 or CONFIG_INET are selected.
Building a defconfig with both of these symbols unselected (Using the ARM
at91sam9rl_defconfig, for example) leads to the following build warning:
$ make at91sam9rl_defconfig
#
# configuration written to .config
#
$ make net/core/secure_seq.o
scripts/kconfig/conf --silentoldconfig Kconfig
CHK include/config/kernel.release
CHK include/generated/uapi/linux/version.h
CHK include/generated/utsrelease.h
make[1]: `include/generated/mach-types.h' is up to date.
CALL scripts/checksyscalls.sh
CC net/core/secure_seq.o
net/core/secure_seq.c:17:13: warning: 'net_secret_init' defined but not used [-Wunused-function]
Fix this warning by protecting the definition of net_secret() with these
symbols.
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commits 6d36824e730f247b602c90e8715a792003e3c5a7,
02cf4ebd82, and parts of
7eec4174ff ]
After hearing many people over past years complaining against TSO being
bursty or even buggy, we are proud to present automatic sizing of TSO
packets.
One part of the problem is that tcp_tso_should_defer() uses an heuristic
relying on upcoming ACKS instead of a timer, but more generally, having
big TSO packets makes little sense for low rates, as it tends to create
micro bursts on the network, and general consensus is to reduce the
buffering amount.
This patch introduces a per socket sk_pacing_rate, that approximates
the current sending rate, and allows us to size the TSO packets so
that we try to send one packet every ms.
This field could be set by other transports.
Patch has no impact for high speed flows, where having large TSO packets
makes sense to reach line rate.
For other flows, this helps better packet scheduling and ACK clocking.
This patch increases performance of TCP flows in lossy environments.
A new sysctl (tcp_min_tso_segs) is added, to specify the
minimal size of a TSO packet (default being 2).
A follow-up patch will provide a new packet scheduler (FQ), using
sk_pacing_rate as an input to perform optional per flow pacing.
This explains why we chose to set sk_pacing_rate to twice the current
rate, allowing 'slow start' ramp up.
sk_pacing_rate = 2 * cwnd * mss / srtt
v2: Neal Cardwell reported a suspect deferring of last two segments on
initial write of 10 MSS, I had to change tcp_tso_should_defer() to take
into account tp->xmit_size_goal_segs
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Van Jacobson <vanj@google.com>
Cc: Tom Herbert <therbert@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d0fe8c888b ]
I've been hitting a NULL ptr deref while using netconsole because the
np->dev check and the pointer manipulation in netpoll_cleanup are done
without rtnl and the following sequence happens when having a netconsole
over a vlan and we remove the vlan while disabling the netconsole:
CPU 1 CPU2
removes vlan and calls the notifier
enters store_enabled(), calls
netdev_cleanup which checks np->dev
and then waits for rtnl
executes the netconsole netdev
release notifier making np->dev
== NULL and releases rtnl
continues to dereference a member of
np->dev which at this point is == NULL
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b0dd663b60 ]
The received ARP request type in the Ethernet packet head is ETH_P_ARP other than ETH_P_IP.
[ Bug introduced by commit b7394d2429
("netpoll: prepare for ipv6") ]
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b86783587b ]
In commit 8ed781668d ("flow_keys: include thoff into flow_keys for
later usage"), we missed that existing code was using nhoff as a
temporary variable that could not always contain transport header
offset.
This is not a problem for TCP/UDP because port offset (@poff)
is 0 for these protocols.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 50d1784ee4 ]
commit 416186fbf8 ("net: Split core bits of netdev_pick_tx
into __netdev_pick_tx") added a bug that disables caching of queue
index in the socket.
This is the source of packet reorders for TCP flows, and
again this is happening more often when using FQ pacing.
Old code was doing
if (queue_index != old_index)
sk_tx_queue_set(sk, queue_index);
Alexander renamed the variables but forgot to change sk_tx_queue_set()
2nd parameter.
if (queue_index != new_index)
sk_tx_queue_set(sk, queue_index);
This means we store -1 over and over in sk->sk_tx_queue_mapping
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 702821f4ea ]
commit 8728c544a9 ("net: dev_pick_tx() fix") and commit
b6fe83e952 ("bonding: refine IFF_XMIT_DST_RELEASE capability")
are quite incompatible : Queue selection is disabled because skb
dst was dropped before entering bonding device.
This causes major performance regression, mainly because TCP packets
for a given flow can be sent to multiple queues.
This is particularly visible when using the new FQ packet scheduler
with MQ + FQ setup on the slaves.
We can safely revert the first commit now that 416186fbf8
("net: Split core bits of netdev_pick_tx into __netdev_pick_tx")
properly caps the queue_index.
Reported-by: Xi Wang <xii@google.com>
Diagnosed-by: Xi Wang <xii@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Denys Fedorysychenko <nuclearcat@nuclearcat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3e805ad288 ]
Fix the iproute2 command `bridge vlan show`, after switching from
rtgenmsg to ifinfomsg.
Let's start with a little history:
Feb 20: Vlad Yasevich got his VLAN-aware bridge patchset included in
the 3.9 merge window.
In the kernel commit 6cbdceeb, he added attribute support to
bridge GETLINK requests sent with rtgenmsg.
Mar 6th: Vlad got this iproute2 reference implementation of the bridge
vlan netlink interface accepted (iproute2 9eff0e5c)
Apr 25th: iproute2 switched from using rtgenmsg to ifinfomsg (63338dca)
http://patchwork.ozlabs.org/patch/239602/http://marc.info/?t=136680900700007
Apr 28th: Linus released 3.9
Apr 30th: Stephen released iproute2 3.9.0
The `bridge vlan show` command haven't been working since the switch to
ifinfomsg, or in a released version of iproute2. Since the kernel side
only supports rtgenmsg, which iproute2 switched away from just prior to
the iproute2 3.9.0 release.
I haven't been able to find any documentation, about neither rtgenmsg
nor ifinfomsg, and in which situation to use which, but kernel commit
88c5b5ce seams to suggest that ifinfomsg should be used.
Fixing this in kernel will break compatibility, but I doubt that anybody
have been using it due to this bug in the user space reference
implementation, at least not without noticing this bug. That said the
functionality is still fully functional in 3.9, when reversing iproute2
commit 63338dca.
This could also be fixed in iproute2, but thats an ugly patch that would
reintroduce rtgenmsg in iproute2, and from searching in netdev it seams
like rtgenmsg usage is discouraged. I'm assuming that the only reason
that Vlad implemented the kernel side to use rtgenmsg, was because
iproute2 was using it at the time.
Signed-off-by: Asbjoern Sloth Toennesen <ast@fiberby.net>
Reviewed-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 63134803a6 ]
dev->ndo_neigh_setup() might need some of the values of neigh_parms, so
populate them before calling it.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5f671d6b4e ]
It's possible to assign an invalid value to the net.core.somaxconn
sysctl variable, because there is no checks at all.
The sk_max_ack_backlog field of the sock structure is defined as
unsigned short. Therefore, the backlog argument in inet_listen()
shouldn't exceed USHRT_MAX. The backlog argument in the listen() syscall
is truncated to the somaxconn value. So, the somaxconn value shouldn't
exceed 65535 (USHRT_MAX).
Also, negative values of somaxconn are meaningless.
before:
$ sysctl -w net.core.somaxconn=256
net.core.somaxconn = 256
$ sysctl -w net.core.somaxconn=65536
net.core.somaxconn = 65536
$ sysctl -w net.core.somaxconn=-100
net.core.somaxconn = -100
after:
$ sysctl -w net.core.somaxconn=256
net.core.somaxconn = 256
$ sysctl -w net.core.somaxconn=65536
error: "Invalid argument" setting key "net.core.somaxconn"
$ sysctl -w net.core.somaxconn=-100
error: "Invalid argument" setting key "net.core.somaxconn"
Based on a prior patch from Changli Gao.
Signed-off-by: Roman Gushchin <klamm@yandex-team.ru>
Reported-by: Changli Gao <xiaosuo@gmail.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d4b812dea4 ]
In commit 48cc32d38a
("vlan: don't deliver frames for unknown vlans to protocols")
Florian made sure we set pkt_type to PACKET_OTHERHOST
if the vlan id is set and we could find a vlan device for this
particular id.
But we also have a problem if prio bits are set.
Steinar reported an issue on a router receiving IPv6 frames with a
vlan tag of 4000 (id 0, prio 2), and tunneled into a sit device,
because skb->vlan_tci is set.
Forwarded frame is completely corrupted : We can see (8100:4000)
being inserted in the middle of IPv6 source address :
16:48:00.780413 IP6 2001:16d8:8100:4000:ee1c:0:9d9:bc87 >
9f94:4d95:2001:67c:29f4::: ICMP6, unknown icmp6 type (0), length 64
0x0000: 0000 0029 8000 c7c3 7103 0001 a0ae e651
0x0010: 0000 0000 ccce 0b00 0000 0000 1011 1213
0x0020: 1415 1617 1819 1a1b 1c1d 1e1f 2021 2223
0x0030: 2425 2627 2829 2a2b 2c2d 2e2f 3031 3233
It seems we are not really ready to properly cope with this right now.
We can probably do better in future kernels :
vlan_get_ingress_priority() should be a netdev property instead of
a per vlan_dev one.
For stable kernels, lets clear vlan_tci to fix the bugs.
Reported-by: Steinar H. Gunderson <sesse@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c9ab4d85de ]
There is a race in neighbour code, because neigh_destroy() uses
skb_queue_purge(&neigh->arp_queue) without holding neighbour lock,
while other parts of the code assume neighbour rwlock is what
protects arp_queue
Convert all skb_queue_purge() calls to the __skb_queue_purge() variant
Use __skb_queue_head_init() instead of skb_queue_head_init()
to make clear we do not use arp_queue.lock
And hold neigh->lock in neigh_destroy() to close the race.
Reported-by: Joe Jin <joe.jin@oracle.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the kernel (compiled with CONFIG_PREEMPT=n) is performing the
rename of a network interface, it can end up waiting for a workqueue
to complete. If userland is able to invoke a SIOCGIFNAME ioctl or a
SO_BINDTODEVICE getsockopt in between, the kernel will deadlock due to
the fact that read_secklock_begin() will spin forever waiting for the
writer process (the one doing the interface rename) to update the
devnet_rename_seq sequence.
This patch fixes the problem by adding a helper (netdev_get_name())
and using it in the code handling the SIOCGIFNAME ioctl and
SO_BINDTODEVICE setsockopt.
The netdev_get_name() helper uses raw_seqcount_begin() to avoid
spinning forever, waiting for devnet_rename_seq->sequence to become
even. cond_resched() is used in the contended case, before retrying
the access to give the writer process a chance to finish.
The use of raw_seqcount_begin() will incur some unneeded work in the
reader process in the contended case, but this is better than
deadlocking the system.
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 68c3316311 ("v4 GRE: Add TCP segmentation offload for GRE")
added a possible skb leak, because it frees only the head of segment
list, in case a skb_linearize() call fails.
This patch adds a kfree_skb_list() helper to fix the bug.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Pravin B Shelar <pshelar@nicira.com>
Cc: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of the push to add 802.1ad server provider tagging support to the
kernel the VLAN features flags were renamed. Unfortunately the kernel name
for the VLAN hardware acceleration features that the kernel shows user space
was included in the rename, which broke ethtool (txvlan and rxvlan options
do not work). This patch restores the original names, i.e. the original ABI.
If we wanted to make clear to users that we are refering to CTAGs we can
always change ethtool's short_name and long_name for these features (for
example something along the lines of txvlan -> txvlan-ctag, tx-vlan-offload ->
tx-vlan-ctag-offload).
Cc: Patrick McHardy <kaber@trash.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Filters need to be translated to real BPF code for userland, like SO_GETFILTER.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet spotted that we have to check skb->head instead
of skb->data as skb->head points to the beginning of the
data area of the skbuff. Similarly, we have to initialize the
skb->head pointer, not skb->data in __alloc_skb_head.
After this fix, netlink crashes in the release path of the
sk_buff, so let's fix that as well.
This bug was introduced in (0ebd0ac net: add function to
allocate sk_buff head without data area).
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_mc_sync_multiple function is currently calling
__hw_addr_sync, and not __hw_addr_sync_multiple. This will result in
addresses only being synced to the first device from the set.
Corrected by calling the _multiple variant.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Reviewed-by: Vlad Yasevich <vyasevic@redhat.com>
Tested-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, __hw_addr_sync_one is called in a loop by
__hw_addr_sync_multiple to sync each of a "from" device's hw addresses
to a "to" device. __hw_addr_sync_one calls __hw_addr_add_ex to attempt
to add each address. __hw_addr_add_ex is called with global=false, and
sync=true.
__hw_addr_add_ex checks to see if the new address matches an
address already on the list. If so, it tests global and sync. In this
case, sync=true, and it then checks if the address is already synced,
and if so, returns 0.
This 0 return causes __hw_addr_sync_one to increment the sync_cnt
and refcount for the "from" list's address entry, even though the address
is already synced and has a reference and sync_cnt. This will cause
the sync_cnt and refcount to increment without bound every time an
addresses is added to the "from" device and synced to the "to" device.
The fix here has two parts:
First, when __hw_addr_add_ex finds the address already exists
and is synced, return -EEXIST instead of 0.
Second, __hw_addr_sync_one checks the error return for -EEXIST,
and if so, it (a) does not add a refcount/sync_cnt, and (b) returns 0
itself so that __hw_addr_sync_multiple will not return an error.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Reviewed-by: Vlad Yasevich <vyasevic@redhat.com>
Tested-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an address is added to a subordinate interface (the "to"
list), the address entry in the "from" list is not marked "synced" as
the entry added to the "to" list is.
When performing the unsync operation (e.g., dev_mc_unsync),
__hw_addr_unsync_one calls __hw_addr_del_entry with the "synced"
parameter set to true for the case when the address reference is being
released from the "from" list. This causes a test inside to fail,
with the result being that the reference count on the "from" address
is not properly decremeted and the address on the "from" list will
never be freed.
Correct this by having __hw_addr_unsync_one call the
__hw_addr_del_entry function with the "sync" flag set to false for the
"remove from the from list" case.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Reviewed-by: Vlad Yasevich <vyasevic@redhat.com>
Tested-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sync_cnt field is not being initialized, which can result
in arbitrary values in the field. Fixed by initializing it to zero.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Reviewed-by: Vlad Yasevich <vyasevic@redhat.com>
Tested-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The three arrays of strings: af_family_key_strings,
af_family_slock_key_strings and af_family_clock_key_strings have not
VSOCK's string
Signed-off-by: Federico Vaga <federico.vaga@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ERROR: "memcpy_fromiovec" [drivers/vhost/vhost_scsi.ko] undefined!
That function is only present with CONFIG_NET. Turns out that
crypto/algif_skcipher.c also uses that outside net, but it actually
needs sockets anyway.
In addition, commit 6d4f0139d6 added
CONFIG_NET dependency to CONFIG_VMCI for memcpy_toiovec, so hoist
that function and revert that commit too.
socket.h already includes uio.h, so no callers need updating; trying
only broke things fo x86_64 randconfig (thanks Fengguang!).
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We have seen multiple NULL dereferences in __inet6_lookup_established()
After analysis, I found that inet6_sk() could be NULL while the
check for sk_family == AF_INET6 was true.
Bug was added in linux-2.6.29 when RCU lookups were introduced in UDP
and TCP stacks.
Once an IPv6 socket, using SLAB_DESTROY_BY_RCU is inserted in a hash
table, we no longer can clear pinet6 field.
This patch extends logic used in commit fcbdf09d96
("net: fix nulls list corruptions in sk_prot_alloc")
TCP/UDP/UDPLite IPv6 protocols provide their own .clear_sk() method
to make sure we do not clear pinet6 field.
At socket clone phase, we do not really care, as cloning the parent (non
NULL) pinet6 is not adding a fatal race.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same story as with fib_trie patch - vfree() from RCU callbacks
is legitimate now.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull VFS updates from Al Viro,
Misc cleanups all over the place, mainly wrt /proc interfaces (switch
create_proc_entry to proc_create(), get rid of the deprecated
create_proc_read_entry() in favor of using proc_create_data() and
seq_file etc).
7kloc removed.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits)
don't bother with deferred freeing of fdtables
proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h
proc: Make the PROC_I() and PDE() macros internal to procfs
proc: Supply a function to remove a proc entry by PDE
take cgroup_open() and cpuset_open() to fs/proc/base.c
ppc: Clean up scanlog
ppc: Clean up rtas_flash driver somewhat
hostap: proc: Use remove_proc_subtree()
drm: proc: Use remove_proc_subtree()
drm: proc: Use minor->index to label things, not PDE->name
drm: Constify drm_proc_list[]
zoran: Don't print proc_dir_entry data in debug
reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show()
proc: Supply an accessor for getting the data from a PDE's parent
airo: Use remove_proc_subtree()
rtl8192u: Don't need to save device proc dir PDE
rtl8187se: Use a dir under /proc/net/r8180/
proc: Add proc_mkdir_data()
proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h}
proc: Move PDE_NET() to fs/proc/proc_net.c
...
Pull networking updates from David Miller:
"Highlights (1721 non-merge commits, this has to be a record of some
sort):
1) Add 'random' mode to team driver, from Jiri Pirko and Eric
Dumazet.
2) Make it so that any driver that supports configuration of multiple
MAC addresses can provide the forwarding database add and del
calls by providing a default implementation and hooking that up if
the driver doesn't have an explicit set of handlers. From Vlad
Yasevich.
3) Support GSO segmentation over tunnels and other encapsulating
devices such as VXLAN, from Pravin B Shelar.
4) Support L2 GRE tunnels in the flow dissector, from Michael Dalton.
5) Implement Tail Loss Probe (TLP) detection in TCP, from Nandita
Dukkipati.
6) In the PHY layer, allow supporting wake-on-lan in situations where
the PHY registers have to be written for it to be configured.
Use it to support wake-on-lan in mv643xx_eth.
From Michael Stapelberg.
7) Significantly improve firewire IPV6 support, from YOSHIFUJI
Hideaki.
8) Allow multiple packets to be sent in a single transmission using
network coding in batman-adv, from Martin Hundebøll.
9) Add support for T5 cxgb4 chips, from Santosh Rastapur.
10) Generalize the VXLAN forwarding tables so that there is more
flexibility in configurating various aspects of the endpoints.
From David Stevens.
11) Support RSS and TSO in hardware over GRE tunnels in bxn2x driver,
from Dmitry Kravkov.
12) Zero copy support in nfnelink_queue, from Eric Dumazet and Pablo
Neira Ayuso.
13) Start adding networking selftests.
14) In situations of overload on the same AF_PACKET fanout socket, or
per-cpu packet receive queue, minimize drop by distributing the
load to other cpus/fanouts. From Willem de Bruijn and Eric
Dumazet.
15) Add support for new payload offset BPF instruction, from Daniel
Borkmann.
16) Convert several drivers over to mdoule_platform_driver(), from
Sachin Kamat.
17) Provide a minimal BPF JIT image disassembler userspace tool, from
Daniel Borkmann.
18) Rewrite F-RTO implementation in TCP to match the final
specification of it in RFC4138 and RFC5682. From Yuchung Cheng.
19) Provide netlink socket diag of netlink sockets ("Yo dawg, I hear
you like netlink, so I implemented netlink dumping of netlink
sockets.") From Andrey Vagin.
20) Remove ugly passing of rtnetlink attributes into rtnl_doit
functions, from Thomas Graf.
21) Allow userspace to be able to see if a configuration change occurs
in the middle of an address or device list dump, from Nicolas
Dichtel.
22) Support RFC3168 ECN protection for ipv6 fragments, from Hannes
Frederic Sowa.
23) Increase accuracy of packet length used by packet scheduler, from
Jason Wang.
24) Beginning set of changes to make ipv4/ipv6 fragment handling more
scalable and less susceptible to overload and locking contention,
from Jesper Dangaard Brouer.
25) Get rid of using non-type-safe NLMSG_* macros and use nlmsg_*()
instead. From Hong Zhiguo.
26) Optimize route usage in IPVS by avoiding reference counting where
possible, from Julian Anastasov.
27) Convert IPVS schedulers to RCU, also from Julian Anastasov.
28) Support cpu fanouts in xt_NFQUEUE netfilter target, from Holger
Eitzenberger.
29) Network namespace support for nf_log, ebt_log, xt_LOG, ipt_ULOG,
nfnetlink_log, and nfnetlink_queue. From Gao feng.
30) Implement RFC3168 ECN protection, from Hannes Frederic Sowa.
31) Support several new r8169 chips, from Hayes Wang.
32) Support tokenized interface identifiers in ipv6, from Daniel
Borkmann.
33) Use usbnet_link_change() helper in USB net driver, from Ming Lei.
34) Add 802.1ad vlan offload support, from Patrick McHardy.
35) Support mmap() based netlink communication, also from Patrick
McHardy.
36) Support HW timestamping in mlx4 driver, from Amir Vadai.
37) Rationalize AF_PACKET packet timestamping when transmitting, from
Willem de Bruijn and Daniel Borkmann.
38) Bring parity to what's provided by /proc/net/packet socket dumping
and the info provided by netlink socket dumping of AF_PACKET
sockets. From Nicolas Dichtel.
39) Fix peeking beyond zero sized SKBs in AF_UNIX, from Benjamin
Poirier"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
filter: fix va_list build error
af_unix: fix a fatal race with bit fields
bnx2x: Prevent memory leak when cnic is absent
bnx2x: correct reading of speed capabilities
net: sctp: attribute printl with __printf for gcc fmt checks
netlink: kconfig: move mmap i/o into netlink kconfig
netpoll: convert mutex into a semaphore
netlink: Fix skb ref counting.
net_sched: act_ipt forward compat with xtables
mlx4_en: fix a build error on 32bit arches
Revert "bnx2x: allow nvram test to run when device is down"
bridge: avoid OOPS if root port not found
drivers: net: cpsw: fix kernel warn on cpsw irq enable
sh_eth: use random MAC address if no valid one supplied
3c509.c: call SET_NETDEV_DEV for all device types (ISA/ISAPnP/EISA)
tg3: fix to append hardware time stamping flags
unix/stream: fix peeking with an offset larger than data in queue
unix/dgram: fix peeking with an offset larger than data in queue
unix/dgram: peek beyond 0-sized skbs
openvswitch: Remove unneeded ovs_netdev_get_ifindex()
...
Bart Van Assche recently reported a warning to me:
<IRQ> [<ffffffff8103d79f>] warn_slowpath_common+0x7f/0xc0
[<ffffffff8103d7fa>] warn_slowpath_null+0x1a/0x20
[<ffffffff814761dd>] mutex_trylock+0x16d/0x180
[<ffffffff813968c9>] netpoll_poll_dev+0x49/0xc30
[<ffffffff8136a2d2>] ? __alloc_skb+0x82/0x2a0
[<ffffffff81397715>] netpoll_send_skb_on_dev+0x265/0x410
[<ffffffff81397c5a>] netpoll_send_udp+0x28a/0x3a0
[<ffffffffa0541843>] ? write_msg+0x53/0x110 [netconsole]
[<ffffffffa05418bf>] write_msg+0xcf/0x110 [netconsole]
[<ffffffff8103eba1>] call_console_drivers.constprop.17+0xa1/0x1c0
[<ffffffff8103fb76>] console_unlock+0x2d6/0x450
[<ffffffff8104011e>] vprintk_emit+0x1ee/0x510
[<ffffffff8146f9f6>] printk+0x4d/0x4f
[<ffffffffa0004f1d>] scsi_print_command+0x7d/0xe0 [scsi_mod]
This resulted from my commit ca99ca14c which introduced a mutex_trylock
operation in a path that could execute in interrupt context. When mutex
debugging is enabled, the above warns the user when we are in fact
exectuting in interrupt context
interrupt context.
After some discussion, It seems that a semaphore is the proper mechanism to use
here. While mutexes are defined to be unusable in interrupt context, no such
condition exists for semaphores (save for the fact that the non blocking api
calls, like up and down_trylock must be used when in irq context).
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Bart Van Assche <bvanassche@acm.org>
CC: Bart Van Assche <bvanassche@acm.org>
CC: David Miller <davem@davemloft.net>
CC: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
drivers/net/ethernet/emulex/benet/be.h
include/net/tcp.h
net/mac802154/mac802154.h
Most conflicts were minor overlapping stuff.
The be2net driver brought in some fixes that added __vlan_put_tag
calls, which in net-next take an additional argument.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, peeking on a unix datagram socket with an offset larger than len of
the data in the sk receive queue returns immediately with bogus data. That's
because *off is not reset between each skb_queue_walk().
This patch fixes this so that the behavior is the same as peeking with no
offset on an empty queue: the caller blocks.
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"77c1090 net: fix infinite loop in __skb_recv_datagram()" (v3.8) introduced a
regression:
After that commit, recv can no longer peek beyond a 0-sized skb in the queue.
__skb_recv_datagram() instead stops at the first skb with len == 0 and results
in the system call failing with -EFAULT via skb_copy_datagram_iovec().
When peeking at an offset with 0-sized skb(s), each one of those is received
only once, in sequence. The offset starts moving forward again after receiving
datagrams with len > 0.
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use consume_skb() to free the original skb that is successfully transmitted
as gso segmented skbs so that it is not treated as a drop due to an error.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
