Saeed Mahameed says:
====================
mlx5e-updates-2018-05-25
This series includes updates for mlx5e netdev driver.
1) Allowr flow based VF vport mirroring under sriov switchdev scheme,
added support for offloading the TC mirred mirror sub-action, from
Chris Mi.
=================
From: Or Gerlitz <ogerlitz@mellanox.com>
The user will typically set the actions order such that the mirror
port (mirror VF) sees packets as the original port (VF under
mirroring) sent them or as it will receive them. In the general case,
it means that packets are potentially sent to the mirror port before
or after some actions were applied on them.
To properly do that, we follow on the exact action order as set for
the flow and make sure this will also be the case when we program the
HW offload.
If all the actions should apply before forwarding to the mirror and dest port,
mirroring is just multicasting to the two vports. Otherwise, we split
the TC flow to two HW rules, where the 1st applies only the actions
needed up to the mirror (if there are such) and the 2nd the rest of
the actions plus the forwarding to the dest vport.
=================
2) Move to order-0 only allocations (using fragmented work queues) for all
work queues used by the driver, RX and TX descriptor rings
(RQs, SQs and Completion Queues (CQs)), from Tariq Toukan.
3) Avoid resetting netdevice statistics on netdevice
state changes, from Eran Ben Elisha.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct Qdisc has a lot of holes, especially after commit
a53851e2c3 ("net: sched: explicit locking in gso_cpu fallback"),
which as a side effect, moved the fields just after 'busylock'
on a new cacheline.
Since both 'padded' and 'refcnt' are not updated frequently, and
there is a hole before 'gso_skb', we can move such fields there,
saving a cacheline without any performance side effect.
Before this commit:
pahole -C Qdisc net/sche/sch_generic.o
# ...
/* size: 384, cachelines: 6, members: 25 */
/* sum members: 236, holes: 3, sum holes: 92 */
/* padding: 56 */
After this commit:
pahole -C Qdisc net/sche/sch_generic.o
# ...
/* size: 320, cachelines: 5, members: 25 */
/* sum members: 236, holes: 2, sum holes: 28 */
/* padding: 56 */
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to move some definitions in ptp_qoriq.c
to the header file.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This feature bit can be used by hypervisor to indicate virtio_net device to
act as a standby for another device with the same MAC address.
VIRTIO_NET_F_STANDBY is defined as bit 62 as it is a device feature bit.
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The net_failover driver provides an automated failover mechanism via APIs
to create and destroy a failover master netdev and manages a primary and
standby slave netdevs that get registered via the generic failover
infrastructure.
The failover netdev acts a master device and controls 2 slave devices. The
original paravirtual interface gets registered as 'standby' slave netdev and
a passthru/vf device with the same MAC gets registered as 'primary' slave
netdev. Both 'standby' and 'failover' netdevs are associated with the same
'pci' device. The user accesses the network interface via 'failover' netdev.
The 'failover' netdev chooses 'primary' netdev as default for transmits when
it is available with link up and running.
This can be used by paravirtual drivers to enable an alternate low latency
datapath. It also enables hypervisor controlled live migration of a VM with
direct attached VF by failing over to the paravirtual datapath when the VF
is unplugged.
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The failover module provides a generic interface for paravirtual drivers
to register a netdev and a set of ops with a failover instance. The ops
are used as event handlers that get called to handle netdev register/
unregister/link change/name change events on slave pci ethernet devices
with the same mac address as the failover netdev.
This enables paravirtual drivers to use a VF as an accelerated low latency
datapath. It also allows migration of VMs with direct attached VFs by
failing over to the paravirtual datapath when the VF is unplugged.
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge misc fixes from Andrew Morton:
"16 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
kasan: fix memory hotplug during boot
kasan: free allocated shadow memory on MEM_CANCEL_ONLINE
checkpatch: fix macro argument precedence test
init/main.c: include <linux/mem_encrypt.h>
kernel/sys.c: fix potential Spectre v1 issue
mm/memory_hotplug: fix leftover use of struct page during hotplug
proc: fix smaps and meminfo alignment
mm: do not warn on offline nodes unless the specific node is explicitly requested
mm, memory_hotplug: make has_unmovable_pages more robust
mm/kasan: don't vfree() nonexistent vm_area
MAINTAINERS: change hugetlbfs maintainer and update files
ipc/shm: fix shmat() nil address after round-down when remapping
Revert "ipc/shm: Fix shmat mmap nil-page protection"
idr: fix invalid ptr dereference on item delete
ocfs2: revert "ocfs2/o2hb: check len for bio_add_page() to avoid getting incorrect bio"
mm: fix nr_rotate_swap leak in swapon() error case
Pull networking fixes from David Miller:
"Let's begin the holiday weekend with some networking fixes:
1) Whoops need to restrict cfg80211 wiphy names even more to 64
bytes. From Eric Biggers.
2) Fix flags being ignored when using kernel_connect() with SCTP,
from Xin Long.
3) Use after free in DCCP, from Alexey Kodanev.
4) Need to check rhltable_init() return value in ipmr code, from Eric
Dumazet.
5) XDP handling fixes in virtio_net from Jason Wang.
6) Missing RTA_TABLE in rtm_ipv4_policy[], from Roopa Prabhu.
7) Need to use IRQ disabling spinlocks in mlx4_qp_lookup(), from Jack
Morgenstein.
8) Prevent out-of-bounds speculation using indexes in BPF, from
Daniel Borkmann.
9) Fix regression added by AF_PACKET link layer cure, from Willem de
Bruijn.
10) Correct ENIC dma mask, from Govindarajulu Varadarajan.
11) Missing config options for PMTU tests, from Stefano Brivio"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (48 commits)
ibmvnic: Fix partial success login retries
selftests/net: Add missing config options for PMTU tests
mlx4_core: allocate ICM memory in page size chunks
enic: set DMA mask to 47 bit
ppp: remove the PPPIOCDETACH ioctl
ipv4: remove warning in ip_recv_error
net : sched: cls_api: deal with egdev path only if needed
vhost: synchronize IOTLB message with dev cleanup
packet: fix reserve calculation
net/mlx5: IPSec, Fix a race between concurrent sandbox QP commands
net/mlx5e: When RXFCS is set, add FCS data into checksum calculation
bpf: properly enforce index mask to prevent out-of-bounds speculation
net/mlx4: Fix irq-unsafe spinlock usage
net: phy: broadcom: Fix bcm_write_exp()
net: phy: broadcom: Fix auxiliary control register reads
net: ipv4: add missing RTA_TABLE to rtm_ipv4_policy
net/mlx4: fix spelling mistake: "Inrerface" -> "Interface" and rephrase message
ibmvnic: Only do H_EOI for mobility events
tuntap: correctly set SOCKWQ_ASYNC_NOSPACE
virtio-net: fix leaking page for gso packet during mergeable XDP
...
The case of a new numa node got missed in avoiding using the node info
from page_struct during hotplug. In this path we have a call to
register_mem_sect_under_node (which allows us to specify it is hotplug
so don't change the node), via link_mem_sections which unfortunately
does not.
Fix is to pass check_nid through link_mem_sections as well and disable
it in the new numa node path.
Note the bug only 'sometimes' manifests depending on what happens to be
in the struct page structures - there are lots of them and it only needs
to match one of them.
The result of the bug is that (with a new memory only node) we never
successfully call register_mem_sect_under_node so don't get the memory
associated with the node in sysfs and meminfo for the node doesn't
report it.
It came up whilst testing some arm64 hotplug patches, but appears to be
universal. Whilst I'm triggering it by removing then reinserting memory
to a node with no other elements (thus making the node disappear then
appear again), it appears it would happen on hotplugging memory where
there was none before and it doesn't seem to be related the arm64
patches.
These patches call __add_pages (where most of the issue was fixed by
Pavel's patch). If there is a node at the time of the __add_pages call
then all is well as it calls register_mem_sect_under_node from there
with check_nid set to false. Without a node that function returns
having not done the sysfs related stuff as there is no node to use.
This is expected but it is the resulting path that fails...
Exact path to the problem is as follows:
mm/memory_hotplug.c: add_memory_resource()
The node is not online so we enter the 'if (new_node)' twice, on the
second such block there is a call to link_mem_sections which calls
into
drivers/node.c: link_mem_sections() which calls
drivers/node.c: register_mem_sect_under_node() which calls
get_nid_for_pfn and keeps trying until the output of that matches
the expected node (passed all the way down from
add_memory_resource)
It is effectively the same fix as the one referred to in the fixes tag
just in the code path for a new node where the comments point out we
have to rerun the link creation because it will have failed in
register_new_memory (as there was no node at the time). (actually that
comment is wrong now as we don't have register_new_memory any more it
got renamed to hotplug_memory_register in Pavel's patch).
Link: http://lkml.kernel.org/r/20180504085311.1240-1-Jonathan.Cameron@huawei.com
Fixes: fc44f7f923 ("mm/memory_hotplug: don't read nid from struct page during hotplug")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Pavel Tatashin <pasha.tatashin@oracle.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oscar has noticed that we splat
WARNING: CPU: 0 PID: 64 at ./include/linux/gfp.h:467 vmemmap_alloc_block+0x4e/0xc9
[...]
CPU: 0 PID: 64 Comm: kworker/u4:1 Tainted: G W E 4.17.0-rc5-next-20180517-1-default+ #66
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.0.0-prebuilt.qemu-project.org 04/01/2014
Workqueue: kacpi_hotplug acpi_hotplug_work_fn
Call Trace:
vmemmap_populate+0xf2/0x2ae
sparse_mem_map_populate+0x28/0x35
sparse_add_one_section+0x4c/0x187
__add_pages+0xe7/0x1a0
add_pages+0x16/0x70
add_memory_resource+0xa3/0x1d0
add_memory+0xe4/0x110
acpi_memory_device_add+0x134/0x2e0
acpi_bus_attach+0xd9/0x190
acpi_bus_scan+0x37/0x70
acpi_device_hotplug+0x389/0x4e0
acpi_hotplug_work_fn+0x1a/0x30
process_one_work+0x146/0x340
worker_thread+0x47/0x3e0
kthread+0xf5/0x130
ret_from_fork+0x35/0x40
when adding memory to a node that is currently offline.
The VM_WARN_ON is just too loud without a good reason. In this
particular case we are doing
alloc_pages_node(node, GFP_KERNEL|__GFP_RETRY_MAYFAIL|__GFP_NOWARN, order)
so we do not insist on allocating from the given node (it is more a
hint) so we can fall back to any other populated node and moreover we
explicitly ask to not warn for the allocation failure.
Soften the warning only to cases when somebody asks for the given node
explicitly by __GFP_THISNODE.
Link: http://lkml.kernel.org/r/20180523125555.30039-3-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Oscar Salvador <osalvador@techadventures.net>
Tested-by: Oscar Salvador <osalvador@techadventures.net>
Reviewed-by: Pavel Tatashin <pasha.tatashin@oracle.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Reza Arbab <arbab@linux.vnet.ibm.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Complete the transition of all WQ types to use fragmented
order-0 coherent memory instead of high-order allocations.
CQ-WQ already uses order-0.
Here we do the same for cyclic and linked-list WQs.
This allows the driver to load cleanly on systems with a highly
fragmented coherent memory.
Performance tests:
ConnectX-5 100Gbps, CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
Packet rate of 64B packets, single transmit ring, size 8K.
No degradation is sensed.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Define netlink messages and attributes to support user kernel
communication that uses the conntrack limit feature.
Signed-off-by: Yi-Hung Wei <yihung.wei@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
mlx5e-updates-2018-05-19
This series contains updates for mlx5e netdevice driver with one subject,
DSCP to priority mapping, in the first patch Huy adds the needed API in
dcbnl, the second patch adds the needed mlx5 core capability bits for the
feature, and all other patches are mlx5e (netdev) only changes to add
support for the feature.
From: Huy Nguyen
Dscp to priority mapping for Ethernet packet:
These patches enable differentiated services code point (dscp) to
priority mapping for Ethernet packet. Once this feature is
enabled, the packet is routed to the corresponding priority based on its
dscp. User can combine this feature with priority flow control (pfc)
feature to have priority flow control based on the dscp.
Firmware interface:
Mellanox firmware provides two control knobs for this feature:
QPTS register allow changing the trust state between dscp and
pcp mode. The default is pcp mode. Once in dscp mode, firmware will
route the packet based on its dscp value if the dscp field exists.
QPDPM register allow mapping a specific dscp (0 to 63) to a
specific priority (0 to 7). By default, all the dscps are mapped to
priority zero.
Software interface:
This feature is controlled via application priority TLV. IEEE
specification P802.1Qcd/D2.1 defines priority selector id 5 for
application priority TLV. This APP TLV selector defines DSCP to priority
map. This APP TLV can be sent by the switch or can be set locally using
software such as lldptool. In mlx5 drivers, we add the support for net
dcb's getapp and setapp call back. Mlx5 driver only handles the selector
id 5 application entry (dscp application priority application entry).
If user sends multiple dscp to priority APP TLV entries on the same
dscp, the last sent one will take effect. All the previous sent will be
deleted.
This attribute combined with pfc attribute allows advanced user to
fine tune the qos setting for specific priority queue. For example,
user can give dedicated buffer for one or more priorities or user
can give large buffer to certain priorities.
The dcb buffer configuration will be controlled by lldptool.
>> lldptool -T -i eth2 -V BUFFER prio 0,2,5,7,1,2,3,6
maps priorities 0,1,2,3,4,5,6,7 to receive buffer 0,2,5,7,1,2,3,6
>> lldptool -T -i eth2 -V BUFFER size 87296,87296,0,87296,0,0,0,0
sets receive buffer size for buffer 0,1,2,3,4,5,6,7 respectively
After discussion on mailing list with Jakub, Jiri, Ido and John, we agreed to
choose dcbnl over devlink interface since this feature is intended to set
port attributes which are governed by the netdev instance of that port, where
devlink API is more suitable for global ASIC configurations.
The firmware trust state (in QPTS register) is changed based on the
number of dscp to priority application entries. When the first dscp to
priority application entry is added by the user, the trust state is
changed to dscp. When the last dscp to priority application entry is
deleted by the user, the trust state is changed to pcp.
When the port is in DSCP trust state, the transmit queue is selected
based on the dscp of the skb.
When the port is in DSCP trust state and vport inline mode is not NONE,
firmware requires mlx5 driver to copy the IP header to the
wqe ethernet segment inline header if the skb has it.
This is done by changing the transmit queue sq's min inline mode to L3.
Note that the min inline mode of sqs that belong to other features
such as xdpsq, icosq are not modified.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch, User can configure for the supported
flows to be dropped. Added a stat "gft_filter_drop"
as well to be populated in ethtool for the dropped flows.
For example -
ethtool -N p5p1 flow-type udp4 dst-port 8000 action -1
ethtool -N p5p1 flow-type tcp4 scr-ip 192.168.8.1 action -1
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, driver supports flow classification to PF
receive queues based on TCP/UDP 4 tuples [src_ip, dst_ip,
src_port, dst_port] only.
This patch enables to configure different flow profiles
[For example - only UDP dest port or src_ip based] on the
adapter so that classification can be done according to
just those fields as well. Although, at a time just one
type of flow configuration is supported due to limited
number of flow profiles available on the device.
For example -
ethtool -N enp7s0f0 flow-type udp4 dst-port 45762 action 2
ethtool -N enp7s0f0 flow-type tcp4 src-ip 192.16.4.10 action 1
ethtool -N enp7s0f0 flow-type udp6 dst-port 45762 action 3
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2018-05-24
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix a bug in the original fix to prevent out of bounds speculation when
multiple tail call maps from different branches or calls end up at the
same tail call helper invocation, from Daniel.
2) Two selftest fixes, one in reuseport_bpf_numa where test is skipped in
case of missing numa support and another one to update kernel config to
properly support xdp_meta.sh test, from Anders.
...
Would be great if you have a chance to merge net into net-next after that.
The verifier fix would be needed later as a dependency in bpf-next for
upcomig work there. When you do the merge there's a trivial conflict on
BPF side with 849fa50662 ("bpf/verifier: refine retval R0 state for
bpf_get_stack helper"): Resolution is to keep both functions, the
do_refine_retval_range() and record_func_map().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for a new port flag - BR_ISOLATED. If it is set
then isolated ports cannot communicate between each other, but they can
still communicate with non-isolated ports. The same can be achieved via
ACLs but they can't scale with large number of ports and also the
complexity of the rules grows. This feature can be used to achieve
isolated vlan functionality (similar to pvlan) as well, though currently
it will be port-wide (for all vlans on the port). The new test in
should_deliver uses data that is already cache hot and the new boolean
is used to avoid an additional source port test in should_deliver.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
LAG upper event notifiers contain the tx type used by the LAG device.
Extend this to also include the hash policy used for tx types that
utilize hashing.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tracepoint does not add value and the call to fib_lookup follows
it which shows the same information and the fib lookup result.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bb0ad1987e ("ipv6: fib6_rules: support for match on sport, dport
and ip proto") added support for protocol and ports to FIB rules.
Update the FIB lookup tracepoint to dump the parameters.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4a2d73a4fb ("ipv4: fib_rules: support match on sport, dport
and ip proto") added support for protocol and ports to FIB rules.
Update the FIB lookup tracepoint to dump the parameters.
In addition, make the IPv4 tracepoint similar to the IPv6 one where
the lookup parameters and result are dumped in 1 event. It is much
easier to use and understand the outcome of the lookup.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 05f0fe6b74 ("RCU, workqueue: Implement rcu_work") introduces
new API's for dispatching work in a RCU callback. Now we can just
switch to the new API's for tc filters. This could get rid of a lot
of code.
Cc: Tejun Heo <tj@kernel.org>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPPIOCDETACH ioctl effectively tries to "close" the given ppp file
before f_count has reached 0, which is fundamentally a bad idea. It
does check 'f_count < 2', which excludes concurrent operations on the
file since they would only be possible with a shared fd table, in which
case each fdget() would take a file reference. However, it fails to
account for the fact that even with 'f_count == 1' the file can still be
linked into epoll instances. As reported by syzbot, this can trivially
be used to cause a use-after-free.
Yet, the only known user of PPPIOCDETACH is pppd versions older than
ppp-2.4.2, which was released almost 15 years ago (November 2003).
Also, PPPIOCDETACH apparently stopped working reliably at around the
same time, when the f_count check was added to the kernel, e.g. see
https://lkml.org/lkml/2002/12/31/83. Also, the current 'f_count < 2'
check makes PPPIOCDETACH only work in single-threaded applications; it
always fails if called from a multithreaded application.
All pppd versions released in the last 15 years just close() the file
descriptor instead.
Therefore, instead of hacking around this bug by exporting epoll
internals to modules, and probably missing other related bugs, just
remove the PPPIOCDETACH ioctl and see if anyone actually notices. Leave
a stub in place that prints a one-time warning and returns EINVAL.
Reported-by: syzbot+16363c99d4134717c05b@syzkaller.appspotmail.com
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Guillaume Nault <g.nault@alphalink.fr>
Tested-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2018-05-24
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Björn Töpel cleans up AF_XDP (removes rebind, explicit cache alignment from uapi, etc).
2) David Ahern adds mtu checks to bpf_ipv{4,6}_fib_lookup() helpers.
3) Jesper Dangaard Brouer adds bulking support to ndo_xdp_xmit.
4) Jiong Wang adds support for indirect and arithmetic shifts to NFP
5) Martin KaFai Lau cleans up BTF uapi and makes the btf_header extensible.
6) Mathieu Xhonneux adds an End.BPF action to seg6local with BPF helpers allowing
to edit/grow/shrink a SRH and apply on a packet generic SRv6 actions.
7) Sandipan Das adds support for bpf2bpf function calls in ppc64 JIT.
8) Yonghong Song adds BPF_TASK_FD_QUERY command for introspection of tracing events.
9) other misc fixes from Gustavo A. R. Silva, Sirio Balmelli, John Fastabend, and Magnus Karlsson
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Extending tracepoint xdp:xdp_devmap_xmit in devmap with an err code
allow people to easier identify the reason behind the ndo_xdp_xmit
call to a given driver is failing.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch change the API for ndo_xdp_xmit to support bulking
xdp_frames.
When kernel is compiled with CONFIG_RETPOLINE, XDP sees a huge slowdown.
Most of the slowdown is caused by DMA API indirect function calls, but
also the net_device->ndo_xdp_xmit() call.
Benchmarked patch with CONFIG_RETPOLINE, using xdp_redirect_map with
single flow/core test (CPU E5-1650 v4 @ 3.60GHz), showed
performance improved:
for driver ixgbe: 6,042,682 pps -> 6,853,768 pps = +811,086 pps
for driver i40e : 6,187,169 pps -> 6,724,519 pps = +537,350 pps
With frames avail as a bulk inside the driver ndo_xdp_xmit call,
further optimizations are possible, like bulk DMA-mapping for TX.
Testing without CONFIG_RETPOLINE show the same performance for
physical NIC drivers.
The virtual NIC driver tun sees a huge performance boost, as it can
avoid doing per frame producer locking, but instead amortize the
locking cost over the bulk.
V2: Fix compile errors reported by kbuild test robot <lkp@intel.com>
V4: Isolated ndo, driver changes and callers.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
When sending an xdp_frame through xdp_do_redirect call, then error
cases can happen where the xdp_frame needs to be dropped, and
returning an -errno code isn't sufficient/possible any-longer
(e.g. for cpumap case). This is already fully supported, by simply
calling xdp_return_frame.
This patch is an optimization, which provides xdp_return_frame_rx_napi,
which is a faster variant for these error cases. It take advantage of
the protection provided by XDP RX running under NAPI protection.
This change is mostly relevant for drivers using the page_pool
allocator as it can take advantage of this. (Tested with mlx5).
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Notice how this allow us get XDP statistic without affecting the XDP
performance, as tracepoint is no-longer activated on a per packet basis.
V5: Spotted by John Fastabend.
Fix 'sent' also counted 'drops' in this patch, a later patch corrected
this, but it was a mistake in this intermediate step.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Functionality is the same, but the ndo_xdp_xmit call is now
simply invoked from inside the devmap.c code.
V2: Fix compile issue reported by kbuild test robot <lkp@intel.com>
V5: Cleanups requested by Daniel
- Newlines before func definition
- Use BUILD_BUG_ON checks
- Remove unnecessary use return value store in dev_map_enqueue
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Currently, suppose a userspace application has loaded a bpf program
and attached it to a tracepoint/kprobe/uprobe, and a bpf
introspection tool, e.g., bpftool, wants to show which bpf program
is attached to which tracepoint/kprobe/uprobe. Such attachment
information will be really useful to understand the overall bpf
deployment in the system.
There is a name field (16 bytes) for each program, which could
be used to encode the attachment point. There are some drawbacks
for this approaches. First, bpftool user (e.g., an admin) may not
really understand the association between the name and the
attachment point. Second, if one program is attached to multiple
places, encoding a proper name which can imply all these
attachments becomes difficult.
This patch introduces a new bpf subcommand BPF_TASK_FD_QUERY.
Given a pid and fd, if the <pid, fd> is associated with a
tracepoint/kprobe/uprobe perf event, BPF_TASK_FD_QUERY will return
. prog_id
. tracepoint name, or
. k[ret]probe funcname + offset or kernel addr, or
. u[ret]probe filename + offset
to the userspace.
The user can use "bpftool prog" to find more information about
bpf program itself with prog_id.
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
A new extern function, perf_get_event(), is added to return a perf event
given a struct file. This function will be used in later patches.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add pbmc and pptb in the port_access_reg_cap_mask. These two
bits determine if device supports receive buffer configuration.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In this patch, we add dcbnl buffer attribute to allow user
change the NIC's buffer configuration such as priority
to buffer mapping and buffer size of individual buffer.
This attribute combined with pfc attribute allows advanced user to
fine tune the qos setting for specific priority queue. For example,
user can give dedicated buffer for one or more priorities or user
can give large buffer to certain priorities.
The dcb buffer configuration will be controlled by lldptool.
lldptool -T -i eth2 -V BUFFER prio 0,2,5,7,1,2,3,6
maps priorities 0,1,2,3,4,5,6,7 to receive buffer 0,2,5,7,1,2,3,6
lldptool -T -i eth2 -V BUFFER size 87296,87296,0,87296,0,0,0,0
sets receive buffer size for buffer 0,1,2,3,4,5,6,7 respectively
After discussion on mailing list with Jakub, Jiri, Ido and John, we agreed to
choose dcbnl over devlink interface since this feature is intended to set
port attributes which are governed by the netdev instance of that port, where
devlink API is more suitable for global ASIC configurations.
We present an use case scenario where dcbnl buffer attribute configured
by advance user helps reduce the latency of messages of different sizes.
Scenarios description:
On ConnectX-5, we run latency sensitive traffic with
small/medium message sizes ranging from 64B to 256KB and bandwidth sensitive
traffic with large messages sizes 512KB and 1MB. We group small, medium,
and large message sizes to their own pfc enables priorities as follow.
Priorities 1 & 2 (64B, 256B and 1KB)
Priorities 3 & 4 (4KB, 8KB, 16KB, 64KB, 128KB and 256KB)
Priorities 5 & 6 (512KB and 1MB)
By default, ConnectX-5 maps all pfc enabled priorities to a single
lossless fixed buffer size of 50% of total available buffer space. The
other 50% is assigned to lossy buffer. Using dcbnl buffer attribute,
we create three equal size lossless buffers. Each buffer has 25% of total
available buffer space. Thus, the lossy buffer size reduces to 25%. Priority
to lossless buffer mappings are set as follow.
Priorities 1 & 2 on lossless buffer #1
Priorities 3 & 4 on lossless buffer #2
Priorities 5 & 6 on lossless buffer #3
We observe improvements in latency for small and medium message sizes
as follows. Please note that the large message sizes bandwidth performance is
reduced but the total bandwidth remains the same.
256B message size (42 % latency reduction)
4K message size (21% latency reduction)
64K message size (16% latency reduction)
CC: Ido Schimmel <idosch@idosch.org>
CC: Jakub Kicinski <jakub.kicinski@netronome.com>
CC: Jiri Pirko <jiri@resnulli.us>
CC: Or Gerlitz <gerlitz.or@gmail.com>
CC: Parav Pandit <parav@mellanox.com>
CC: Aron Silverton <aron.silverton@oracle.com>
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Pull rdma fixes from Jason Gunthorpe:
"This is pretty much just the usual array of smallish driver bugs.
- remove bouncing addresses from the MAINTAINERS file
- kernel oops and bad error handling fixes for hfi, i40iw, cxgb4, and
hns drivers
- various small LOC behavioral/operational bugs in mlx5, hns, qedr
and i40iw drivers
- two fixes for patches already sent during the merge window
- a long-standing bug related to not decreasing the pinned pages
count in the right MM was found and fixed"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (28 commits)
RDMA/hns: Move the location for initializing tmp_len
RDMA/hns: Bugfix for cq record db for kernel
IB/uverbs: Fix uverbs_attr_get_obj
RDMA/qedr: Fix doorbell bar mapping for dpi > 1
IB/umem: Use the correct mm during ib_umem_release
iw_cxgb4: Fix an error handling path in 'c4iw_get_dma_mr()'
RDMA/i40iw: Avoid panic when reading back the IRQ affinity hint
RDMA/i40iw: Avoid reference leaks when processing the AEQ
RDMA/i40iw: Avoid panic when objects are being created and destroyed
RDMA/hns: Fix the bug with NULL pointer
RDMA/hns: Set NULL for __internal_mr
RDMA/hns: Enable inner_pa_vld filed of mpt
RDMA/hns: Set desc_dma_addr for zero when free cmq desc
RDMA/hns: Fix the bug with rq sge
RDMA/hns: Not support qp transition from reset to reset for hip06
RDMA/hns: Add return operation when configured global param fail
RDMA/hns: Update convert function of endian format
RDMA/hns: Load the RoCE dirver automatically
RDMA/hns: Bugfix for rq record db for kernel
RDMA/hns: Add rq inline flags judgement
...
In struct phy_device we have a number of flags being defined as type
bool. Similar to e.g. struct pci_dev we can save some space by using
bit-fields.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts the following commits that change CMA design in MM.
3d2054ad8c ("ARM: CMA: avoid double mapping to the CMA area if CONFIG_HIGHMEM=y")
1d47a3ec09 ("mm/cma: remove ALLOC_CMA")
bad8c6c0b1 ("mm/cma: manage the memory of the CMA area by using the ZONE_MOVABLE")
Ville reported a following error on i386.
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
microcode: microcode updated early to revision 0x4, date = 2013-06-28
Initializing CPU#0
Initializing HighMem for node 0 (000377fe:00118000)
Initializing Movable for node 0 (00000001:00118000)
BUG: Bad page state in process swapper pfn:377fe
page:f53effc0 count:0 mapcount:-127 mapping:00000000 index:0x0
flags: 0x80000000()
raw: 80000000 00000000 00000000 ffffff80 00000000 00000100 00000200 00000001
page dumped because: nonzero mapcount
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 4.17.0-rc5-elk+ #145
Hardware name: Dell Inc. Latitude E5410/03VXMC, BIOS A15 07/11/2013
Call Trace:
dump_stack+0x60/0x96
bad_page+0x9a/0x100
free_pages_check_bad+0x3f/0x60
free_pcppages_bulk+0x29d/0x5b0
free_unref_page_commit+0x84/0xb0
free_unref_page+0x3e/0x70
__free_pages+0x1d/0x20
free_highmem_page+0x19/0x40
add_highpages_with_active_regions+0xab/0xeb
set_highmem_pages_init+0x66/0x73
mem_init+0x1b/0x1d7
start_kernel+0x17a/0x363
i386_start_kernel+0x95/0x99
startup_32_smp+0x164/0x168
The reason for this error is that the span of MOVABLE_ZONE is extended
to whole node span for future CMA initialization, and, normal memory is
wrongly freed here. I submitted the fix and it seems to work, but,
another problem happened.
It's so late time to fix the later problem so I decide to reverting the
series.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Laura Abbott <labbott@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While reviewing the verifier code, I recently noticed that the
following two program variants in relation to tail calls can be
loaded.
Variant 1:
# bpftool p d x i 15
0: (15) if r1 == 0x0 goto pc+3
1: (18) r2 = map[id:5]
3: (05) goto pc+2
4: (18) r2 = map[id:6]
6: (b7) r3 = 7
7: (35) if r3 >= 0xa0 goto pc+2
8: (54) (u32) r3 &= (u32) 255
9: (85) call bpf_tail_call#12
10: (b7) r0 = 1
11: (95) exit
# bpftool m s i 5
5: prog_array flags 0x0
key 4B value 4B max_entries 4 memlock 4096B
# bpftool m s i 6
6: prog_array flags 0x0
key 4B value 4B max_entries 160 memlock 4096B
Variant 2:
# bpftool p d x i 20
0: (15) if r1 == 0x0 goto pc+3
1: (18) r2 = map[id:8]
3: (05) goto pc+2
4: (18) r2 = map[id:7]
6: (b7) r3 = 7
7: (35) if r3 >= 0x4 goto pc+2
8: (54) (u32) r3 &= (u32) 3
9: (85) call bpf_tail_call#12
10: (b7) r0 = 1
11: (95) exit
# bpftool m s i 8
8: prog_array flags 0x0
key 4B value 4B max_entries 160 memlock 4096B
# bpftool m s i 7
7: prog_array flags 0x0
key 4B value 4B max_entries 4 memlock 4096B
In both cases the index masking inserted by the verifier in order
to control out of bounds speculation from a CPU via b2157399cc
("bpf: prevent out-of-bounds speculation") seems to be incorrect
in what it is enforcing. In the 1st variant, the mask is applied
from the map with the significantly larger number of entries where
we would allow to a certain degree out of bounds speculation for
the smaller map, and in the 2nd variant where the mask is applied
from the map with the smaller number of entries, we get buggy
behavior since we truncate the index of the larger map.
The original intent from commit b2157399cc is to reject such
occasions where two or more different tail call maps are used
in the same tail call helper invocation. However, the check on
the BPF_MAP_PTR_POISON is never hit since we never poisoned the
saved pointer in the first place! We do this explicitly for map
lookups but in case of tail calls we basically used the tail
call map in insn_aux_data that was processed in the most recent
path which the verifier walked. Thus any prior path that stored
a pointer in insn_aux_data at the helper location was always
overridden.
Fix it by moving the map pointer poison logic into a small helper
that covers both BPF helpers with the same logic. After that in
fixup_bpf_calls() the poison check is then hit for tail calls
and the program rejected. Latter only happens in unprivileged
case since this is the *only* occasion where a rewrite needs to
happen, and where such rewrite is specific to the map (max_entries,
index_mask). In the privileged case the rewrite is generic for
the insn->imm / insn->code update so multiple maps from different
paths can be handled just fine since all the remaining logic
happens in the instruction processing itself. This is similar
to the case of map lookups: in case there is a collision of
maps in fixup_bpf_calls() we must skip the inlined rewrite since
this will turn the generic instruction sequence into a non-
generic one. Thus the patch_call_imm will simply update the
insn->imm location where the bpf_map_lookup_elem() will later
take care of the dispatch. Given we need this 'poison' state
as a check, the information of whether a map is an unpriv_array
gets lost, so enforcing it prior to that needs an additional
state. In general this check is needed since there are some
complex and tail call intensive BPF programs out there where
LLVM tends to generate such code occasionally. We therefore
convert the map_ptr rather into map_state to store all this
w/o extra memory overhead, and the bit whether one of the maps
involved in the collision was from an unpriv_array thus needs
to be retained as well there.
Fixes: b2157399cc ("bpf: prevent out-of-bounds speculation")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch adds the End.BPF action to the LWT seg6local infrastructure.
This action works like any other seg6local End action, meaning that an IPv6
header with SRH is needed, whose DA has to be equal to the SID of the
action. It will also advance the SRH to the next segment, the BPF program
does not have to take care of this.
Since the BPF program may not be a source of instability in the kernel, it
is important to ensure that the integrity of the packet is maintained
before yielding it back to the IPv6 layer. The hook hence keeps track if
the SRH has been altered through the helpers, and re-validates its
content if needed with seg6_validate_srh. The state kept for validation is
stored in a per-CPU buffer. The BPF program is not allowed to directly
write into the packet, and only some fields of the SRH can be altered
through the helper bpf_lwt_seg6_store_bytes.
Performances profiling has shown that the SRH re-validation does not induce
a significant overhead. If the altered SRH is deemed as invalid, the packet
is dropped.
This validation is also done before executing any action through
bpf_lwt_seg6_action, and will not be performed again if the SRH is not
modified after calling the action.
The BPF program may return 3 types of return codes:
- BPF_OK: the End.BPF action will look up the next destination through
seg6_lookup_nexthop.
- BPF_REDIRECT: if an action has been executed through the
bpf_lwt_seg6_action helper, the BPF program should return this
value, as the skb's destination is already set and the default
lookup should not be performed.
- BPF_DROP : the packet will be dropped.
Signed-off-by: Mathieu Xhonneux <m.xhonneux@gmail.com>
Acked-by: David Lebrun <dlebrun@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The new bpf_lwt_push_encap helper should only be accessible within the
LWT BPF IN hook, and not the OUT one, as this may lead to a skb under
panic.
At the moment, both LWT BPF IN and OUT share the same list of helpers,
whose calls are authorized by the verifier. This patch separates the
verifier ops for the IN and OUT hooks, and allows the IN hook to call the
bpf_lwt_push_encap helper.
This patch is also the occasion to put all lwt_*_func_proto functions
together for clarity. At the moment, socks_op_func_proto is in the middle
of lwt_inout_func_proto and lwt_xmit_func_proto.
Signed-off-by: Mathieu Xhonneux <m.xhonneux@gmail.com>
Acked-by: David Lebrun <dlebrun@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The BPF seg6local hook should be powerful enough to enable users to
implement most of the use-cases one could think of. After some thinking,
we figured out that the following actions should be possible on a SRv6
packet, requiring 3 specific helpers :
- bpf_lwt_seg6_store_bytes: Modify non-sensitive fields of the SRH
- bpf_lwt_seg6_adjust_srh: Allow to grow or shrink a SRH
(to add/delete TLVs)
- bpf_lwt_seg6_action: Apply some SRv6 network programming actions
(specifically End.X, End.T, End.B6 and
End.B6.Encap)
The specifications of these helpers are provided in the patch (see
include/uapi/linux/bpf.h).
The non-sensitive fields of the SRH are the following : flags, tag and
TLVs. The other fields can not be modified, to maintain the SRH
integrity. Flags, tag and TLVs can easily be modified as their validity
can be checked afterwards via seg6_validate_srh. It is not allowed to
modify the segments directly. If one wants to add segments on the path,
he should stack a new SRH using the End.B6 action via
bpf_lwt_seg6_action.
Growing, shrinking or editing TLVs via the helpers will flag the SRH as
invalid, and it will have to be re-validated before re-entering the IPv6
layer. This flag is stored in a per-CPU buffer, along with the current
header length in bytes.
Storing the SRH len in bytes in the control block is mandatory when using
bpf_lwt_seg6_adjust_srh. The Header Ext. Length field contains the SRH
len rounded to 8 bytes (a padding TLV can be inserted to ensure the 8-bytes
boundary). When adding/deleting TLVs within the BPF program, the SRH may
temporary be in an invalid state where its length cannot be rounded to 8
bytes without remainder, hence the need to store the length in bytes
separately. The caller of the BPF program can then ensure that the SRH's
final length is valid using this value. Again, a final SRH modified by a
BPF program which doesn’t respect the 8-bytes boundary will be discarded
as it will be considered as invalid.
Finally, a fourth helper is provided, bpf_lwt_push_encap, which is
available from the LWT BPF IN hook, but not from the seg6local BPF one.
This helper allows to encapsulate a Segment Routing Header (either with
a new outer IPv6 header, or by inlining it directly in the existing IPv6
header) into a non-SRv6 packet. This helper is required if we want to
offer the possibility to dynamically encapsulate a SRH for non-SRv6 packet,
as the BPF seg6local hook only works on traffic already containing a SRH.
This is the BPF equivalent of the seg6 LWT infrastructure, which achieves
the same purpose but with a static SRH per route.
These helpers require CONFIG_IPV6=y (and not =m).
Signed-off-by: Mathieu Xhonneux <m.xhonneux@gmail.com>
Acked-by: David Lebrun <dlebrun@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The function lookup_nexthop is essential to implement most of the seg6local
actions. As we want to provide a BPF helper allowing to apply some of these
actions on the packet being processed, the helper should be able to call
this function, hence the need to make it public.
Moreover, if one argument is incorrect or if the next hop can not be found,
an error should be returned by the BPF helper so the BPF program can adapt
its processing of the packet (return an error, properly force the drop,
...). This patch hence makes this function return dst->error to indicate a
possible error.
Signed-off-by: Mathieu Xhonneux <m.xhonneux@gmail.com>
Acked-by: David Lebrun <dlebrun@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
include/net/seg6.h cannot be included in a source file if CONFIG_IPV6 is
not enabled:
include/net/seg6.h: In function 'seg6_pernet':
>> include/net/seg6.h:52:14: error: 'struct net' has no member named
'ipv6'; did you mean 'ipv4'?
return net->ipv6.seg6_data;
^~~~
ipv4
This commit makes seg6_pernet return NULL if IPv6 is not compiled, hence
allowing seg6.h to be included regardless of the configuration.
Signed-off-by: Mathieu Xhonneux <m.xhonneux@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This adds new two new fields to struct bpf_prog_info. For
multi-function programs, these fields can be used to pass
a list of the JITed image lengths of each function for a
given program to userspace using the bpf system call with
the BPF_OBJ_GET_INFO_BY_FD command.
This can be used by userspace applications like bpftool
to split up the contiguous JITed dump, also obtained via
the system call, into more relatable chunks corresponding
to each function.
Signed-off-by: Sandipan Das <sandipan@linux.vnet.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This adds new two new fields to struct bpf_prog_info. For
multi-function programs, these fields can be used to pass
a list of kernel symbol addresses for all functions in a
given program to userspace using the bpf system call with
the BPF_OBJ_GET_INFO_BY_FD command.
When bpf_jit_kallsyms is enabled, we can get the address
of the corresponding kernel symbol for a callee function
and resolve the symbol's name. The address is determined
by adding the value of the call instruction's imm field
to __bpf_call_base. This offset gets assigned to the imm
field by the verifier.
For some architectures, such as powerpc64, the imm field
is not large enough to hold this offset.
We resolve this by:
[1] Assigning the subprog id to the imm field of a call
instruction in the verifier instead of the offset of
the callee's symbol's address from __bpf_call_base.
[2] Determining the address of a callee's corresponding
symbol by using the imm field as an index for the
list of kernel symbol addresses now available from
the program info.
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sandipan Das <sandipan@linux.vnet.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The err pointer comes from uverbs_attr_get, not from the uobject member,
which does not store an ERR_PTR.
Fixes: be934cca9e ("IB/uverbs: Add device memory registration ioctl support")
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next
tree, they are:
1) Remove obsolete nf_log tracing from nf_tables, from Florian Westphal.
2) Add support for map lookups to numgen, random and hash expressions,
from Laura Garcia.
3) Allow to register nat hooks for iptables and nftables at the same
time. Patchset from Florian Westpha.
4) Timeout support for rbtree sets.
5) ip6_rpfilter works needs interface for link-local addresses, from
Vincent Bernat.
6) Add nf_ct_hook and nf_nat_hook structures and use them.
7) Do not drop packets on packets raceing to insert conntrack entries
into hashes, this is particularly a problem in nfqueue setups.
8) Address fallout from xt_osf separation to nf_osf, patches
from Florian Westphal and Fernando Mancera.
9) Remove reference to struct nft_af_info, which doesn't exist anymore.
From Taehee Yoo.
This batch comes with is a conflict between 25fd386e0b ("netfilter:
core: add missing __rcu annotation") in your tree and 2c205dd398
("netfilter: add struct nf_nat_hook and use it") coming in this batch.
This conflict can be solved by leaving the __rcu tag on
__netfilter_net_init() - added by 25fd386e0b - and remove all code
related to nf_nat_decode_session_hook - which is gone after
2c205dd398, as described by:
diff --cc net/netfilter/core.c
index e0ae4aae96f5,206fb2c4c319..168af54db975
--- a/net/netfilter/core.c
+++ b/net/netfilter/core.c
@@@ -611,7 -580,13 +611,8 @@@ const struct nf_conntrack_zone nf_ct_zo
EXPORT_SYMBOL_GPL(nf_ct_zone_dflt);
#endif /* CONFIG_NF_CONNTRACK */
- static void __net_init __netfilter_net_init(struct nf_hook_entries **e, int max)
-#ifdef CONFIG_NF_NAT_NEEDED
-void (*nf_nat_decode_session_hook)(struct sk_buff *, struct flowi *);
-EXPORT_SYMBOL(nf_nat_decode_session_hook);
-#endif
-
+ static void __net_init
+ __netfilter_net_init(struct nf_hook_entries __rcu **e, int max)
{
int h;
I can also merge your net-next tree into nf-next, solve the conflict and
resend the pull request if you prefer so.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg says:
For this round, we have various things all over the place, notably
* a fix for a race in aggregation, which I want to let
bake for a bit longer before sending to stable
* some new statistics (ACK RSSI, TXQ)
* TXQ configuration
* preparations for HE, particularly radiotap
* replace confusing "country IE" by "country element" since it's
not referring to Ireland
Note that I merged net-next to get a fix from mac80211 that got
there via net, to apply one patch that would otherwise conflict.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
