Function snd_pcm_period_elapsed() is part of sequence servicing HDAudio
stream IRQs. It's called under Global Interrupt Enable (GIE) disabled -
no HDAudio interrupts will be raised. At the same time, the function may
end up calling __snd_pcm_xrun() or snd_pcm_drain_done(). On the
avs-driver side, this translates to IPCs and as GIE is disabled, these
will never complete successfully.
Improve system stability by scheduling stream-IRQ handling in a separate
thread.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://patch.msgid.link/20241008083758.756578-1-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Skip E820 checks for MCFG ECAM regions for new (2016+) machines,
since there's no requirement to describe them in E820 and some
platforms require ECAM to work (Bjorn Helgaas)
- Rename PCI_IRQ_LEGACY to PCI_IRQ_INTX to be more specific (Damien
Le Moal)
- Remove last user and pci_enable_device_io() (Heiner Kallweit)
- Wait for Link Training==0 to avoid possible race (Ilpo Järvinen)
- Skip waiting for devices that have been disconnected while
suspended (Ilpo Järvinen)
- Clear Secondary Status errors after enumeration since Master Aborts
and Unsupported Request errors are an expected part of enumeration
(Vidya Sagar)
MSI:
- Remove unused IMS (Interrupt Message Store) support (Bjorn Helgaas)
Error handling:
- Mask Genesys GL975x SD host controller Replay Timer Timeout
correctable errors caused by a hardware defect; the errors cause
interrupts that prevent system suspend (Kai-Heng Feng)
- Fix EDR-related _DSM support, which previously evaluated revision 5
but assumed revision 6 behavior (Kuppuswamy Sathyanarayanan)
ASPM:
- Simplify link state definitions and mask calculation (Ilpo
Järvinen)
Power management:
- Avoid D3cold for HP Pavilion 17 PC/1972 PCIe Ports, where BIOS
apparently doesn't know how to put them back in D0 (Mario
Limonciello)
CXL:
- Support resetting CXL devices; special handling required because
CXL Ports mask Secondary Bus Reset by default (Dave Jiang)
DOE:
- Support DOE Discovery Version 2 (Alexey Kardashevskiy)
Endpoint framework:
- Set endpoint BAR to be 64-bit if the driver says that's all the
device supports, in addition to doing so if the size is >2GB
(Niklas Cassel)
- Simplify endpoint BAR allocation and setting interfaces (Niklas
Cassel)
Cadence PCIe controller driver:
- Drop DT binding redundant msi-parent and pci-bus.yaml (Krzysztof
Kozlowski)
Cadence PCIe endpoint driver:
- Configure endpoint BARs to be 64-bit based on the BAR type, not the
BAR value (Niklas Cassel)
Freescale Layerscape PCIe controller driver:
- Convert DT binding to YAML (Frank Li)
MediaTek MT7621 PCIe controller driver:
- Add DT binding missing 'reg' property for child Root Ports
(Krzysztof Kozlowski)
- Fix theoretical string truncation in PHY name (Sergio Paracuellos)
NVIDIA Tegra194 PCIe controller driver:
- Return success for endpoint probe instead of falling through to the
failure path (Vidya Sagar)
Renesas R-Car PCIe controller driver:
- Add DT binding missing IOMMU properties (Geert Uytterhoeven)
- Add DT binding R-Car V4H compatible for host and endpoint mode
(Yoshihiro Shimoda)
Rockchip PCIe controller driver:
- Configure endpoint BARs to be 64-bit based on the BAR type, not the
BAR value (Niklas Cassel)
- Add DT binding missing maxItems to ep-gpios (Krzysztof Kozlowski)
- Set the Subsystem Vendor ID, which was previously zero because it
was masked incorrectly (Rick Wertenbroek)
Synopsys DesignWare PCIe controller driver:
- Restructure DBI register access to accommodate devices where this
requires Refclk to be active (Manivannan Sadhasivam)
- Remove the deinit() callback, which was only need by the
pcie-rcar-gen4, and do it directly in that driver (Manivannan
Sadhasivam)
- Add dw_pcie_ep_cleanup() so drivers that support PERST# can clean
up things like eDMA (Manivannan Sadhasivam)
- Rename dw_pcie_ep_exit() to dw_pcie_ep_deinit() to make it parallel
to dw_pcie_ep_init() (Manivannan Sadhasivam)
- Rename dw_pcie_ep_init_complete() to dw_pcie_ep_init_registers() to
reflect the actual functionality (Manivannan Sadhasivam)
- Call dw_pcie_ep_init_registers() directly from all the glue
drivers, not just those that require active Refclk from the host
(Manivannan Sadhasivam)
- Remove the "core_init_notifier" flag, which was an obscure way for
glue drivers to indicate that they depend on Refclk from the host
(Manivannan Sadhasivam)
TI J721E PCIe driver:
- Add DT binding J784S4 SoC Device ID (Siddharth Vadapalli)
- Add DT binding J722S SoC support (Siddharth Vadapalli)
TI Keystone PCIe controller driver:
- Add DT binding missing num-viewport, phys and phy-name properties
(Jan Kiszka)
Miscellaneous:
- Constify and annotate with __ro_after_init (Heiner Kallweit)
- Convert DT bindings to YAML (Krzysztof Kozlowski)
- Check for kcalloc() failure in of_pci_prop_intr_map() (Duoming
Zhou)"
* tag 'pci-v6.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (97 commits)
PCI: Do not wait for disconnected devices when resuming
x86/pci: Skip early E820 check for ECAM region
PCI: Remove unused pci_enable_device_io()
ata: pata_cs5520: Remove unnecessary call to pci_enable_device_io()
PCI: Update pci_find_capability() stub return types
PCI: Remove PCI_IRQ_LEGACY
scsi: vmw_pvscsi: Do not use PCI_IRQ_LEGACY instead of PCI_IRQ_LEGACY
scsi: pmcraid: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: mpt3sas: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: megaraid_sas: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: ipr: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: hpsa: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: arcmsr: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
wifi: rtw89: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
dt-bindings: PCI: rockchip,rk3399-pcie: Add missing maxItems to ep-gpios
Revert "genirq/msi: Provide constants for PCI/IMS support"
Revert "x86/apic/msi: Enable PCI/IMS"
Revert "iommu/vt-d: Enable PCI/IMS"
Revert "iommu/amd: Enable PCI/IMS"
Revert "PCI/MSI: Provide IMS (Interrupt Message Store) support"
...
Merge series from Cezary Rojewski <cezary.rojewski@intel.com>:
The change is based on rafael/acpi-nhlt [1] immutable branch which
Rafael kindly prepared for me. Without the topmost changes to ACPI/NHLT,
the patches present will fail to compile.
Recent changes for the ACPI tree [2] refactored interfaces of the NHLT
table. Currently we have two implementations - one found in acpi
subsystem (unused) and one in sound/hda/. As NHLT is part of ACPI, idea
is to make the former useful and then switch all users of existing
sound/hda/intel-nhlt.c to this new interface over time and remove the
duplicate afterward.
[1]: https://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm.git/?h=acpi-nhlt
[2]: https://lore.kernel.org/linux-acpi/20240319083018.3159716-1-cezary.rojewski@intel.com/
The existing code can be both improved and simplified. To make this
change easier to manage, first add new implementation and then remove
deadcode in a separate patch.
Simplification achieved with:
- reduce the amount of resources requested by the driver i.e.: IPC and
CLDMA request_irq() merged into one
- reduce the number of DSP ops from 2 to 1:
irq_handler/thread() vs dsp_interrupt()
- drop ambiguity around CLDMA interrupt, let skl.c handle that
explicitly as it is the only user
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20240419084857.2719593-2-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC: Updates for v6.9
This has been quite a small release, there's a lot of driver specific
cleanups and minor enhancements but hardly anything on the core and only
one new driver. Highlights include:
- SoundWire support for AMD ACP 6.3 systems.
- Support for reporting version information for AVS firmware.
- Support DSPless mode for Intel Soundwire systems.
- Support for configuring CS35L56 amplifiers using EFI calibration
data.
- Log which component is being operated on as part of power management
trace events.
- Support for Microchip SAM9x7, NXP i.MX95 and Qualcomm WCD939x
Merge series from Cezary Rojewski <cezary.rojewski@intel.com>:
The avs-driver continues to be utilized on more recent Intel machines.
As TGL-based (cAVS 2.5) e.g.: RPL, inherit most of the functionality
from previous platforms:
SKL <- APL <- CNL <- ICL <- TGL
rather than putting everything into a single file, the platform-specific
bits are split into cnl/icl/tgl.c files instead. Makes the division clear
and code easier to maintain.
Layout of the patchset:
First are two changes combined together address the sound-clipping
problem, present when only one stream is running - specifically one
CAPTURE stream.
Follow up is naming-scheme adjustment for some of the existing functions
what improves code incohesiveness. As existing IPC/IRQ code operates
solely on cAVS 1.5 architecture, it needs no abstraction. The situation
changes when newer platforms come into the picture. Thus the next two
patches abstract the existing IPC/IRQ handlers so that majority of the
common code can be re-used.
The ICCMAX change stands out a bit - the AudioDSP firmware loading
procedure differs on ICL-based platforms (and onwards) and having a
separate commit makes the situation clear to the developers who are
going to support the solution from LTS perspective. For that reason
I decided not to merge it into the commit introducing the icl.c file.
ASoC: Updates for v6.7
This is quite a large set of changes but mostly due to API cleanups and
in driver specific ways rather than due to anything subsystem wide.
Highlights include:
- Standardisation of API prefixes on snd_soc_, removing asoc_.
- GPIO API usage improvements.
- Support for HDA patches.
- Lots of work on SOF, including crash dump support.
- Support for AMD platforms with es83xx, Awinc AT87390, many Intel
platforms, many Mediatek platforms, Qualcomm SM6115, Richtek RTQ9128
and Texas Instruments TAS575x.
[ the merge conflicts around SOF Intel HD-audio and CS35L41 subcodec
drivers are resolved here -- tiwai ]
In order to instantiate modules on the firmware side, the driver sends
payload with module configuration. In some case size of this information
is not known before hand, so driver allocates temporary memory during
module creation and frees it after use. Optimize the flow a bit, by
preallocating maximum buffer. This removes the time spend on allocating
memory, as well as potential OOM errors during module initialization.
Handlers for modules, where configuration data fits on stack, are left
as is.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230929112436.787058-4-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Define debugfs subdirectory delegated for IPC communication with DSP.
Input format: uint,uint,(...) which are later translated into DWORDS
sequence and further into instances of struct of interest given the IPC
type.
For Extractor probes, following have been enabled:
- PROBE_POINT_ADD (echo <..> probe_points)
- PROBE_POINT_REMOVE (echo <..> probe_points_remove)
- PROBE_POINT_INFO (cat probe_points)
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221202152841.672536-14-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Provide pgctl/cgctl_mask module parameters for overriding power and
clock gating policies respectively. These help deal with rare firmware
loading failures on some configurations. There're no golden masks that
cover all known problems so leave the defaults as is.
While at it, update avs_hda_l1sen_enable()'s definition so it aligns
with its power/clock friends.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221027124702.1761002-9-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Introduce avs_suspend_standby() and avs_resume_standby() to support S0IX
streaming. The AudioDSP is not shutdown during such scenario and the PCI
device is armed for possible wake operation through an audio event.
As capability for a stream to be active during low power S0 is based off
of ->ignore_suspend, adjust the field's value according to platform
capabilities if needed.
Signed-off-by: Piotr Maziarz <piotrx.maziarz@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221027124702.1761002-8-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
To allow for driver's filesystem interfaces e.g.: debugfs, to be touched
even when the device is asleep, mark IPC-channel as blocked when the
device is suspended. This causes any invocation of said interfaces that
do not toggle PM themselves to gracefully fail with "Operation not
permitted" message.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220707124153.1858249-7-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Define handlers specific to cAVS 1.5+ platforms, that is, APL and
similar platforms. These differ from SKL-alike ones in terms of AudioDSP
firmware generation and thus the '+' suffix. Introduciton of IMR,
removal of CLDMA, D0IX support and monolithic-ation of library/module
code are most impactful but are not the only changes brought with this
newer generation. Some generic and 1.5 operations are being re-used to
reduce code size.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220516101116.190192-16-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
