[ Upstream commit be0b5e6358 ]
Transmission of an AP beacon does not call the TX interrupt service routine,
which usually does the cleanup. Instead, cleanup is handled in a tasklet
completion routine. Unfortunately, this routine has a serious bug in that it does
not release the DMA mapping before it frees the skb, thus one IOMMU mapping is
leaked for each beacon. The test system failed with no free IOMMU mapping slots
approximately one hour after hostapd was used to start an AP.
This issue was reported and tested at https://github.com/lwfinger/rtlwifi_new/issues/30.
Reported-and-tested-by: Kevin Mullican <kevin@mullican.com>
Cc: Kevin Mullican <kevin@mullican.com>
Signed-off-by: Shao Fu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.18+]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 1cf48f22c9 ]
sc->nbcnvifs tracks assigned beacon slots, not enabled beacons.
Therefore, it cannot be used to decide if cur_conf->enable_beacon (bool)
should be updated, or if beacons have been enabled already.
With the current code (depending on the order of calls), beacons often
do not get enabled in an AP+STA setup.
To fix tracking of enabled beacons, convert cur_conf->enable_beacon to a
bitmask of enabled beacon slots.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 9c8928f517 ]
The assumption before this patch was that we don't need to
run again the INIT firmware after the system booted. The
INIT firmware runs calibrations which impact the physical
layer's behavior.
Users reported that it may be helpful to run these
calibrations again every time the interface is brought up.
The penatly is minimal, since the calibrations run fast.
This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=94341
CC: <stable@vger.kernel.org>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit c8f0345586 ]
Routine rtl_is_special_data() is supposed to identify packets that need to
use a low bit rate so that the probability of successful transmission is
high. The current version has a bug that causes all IPv6 packets to be
labelled as special, with a corresponding low rate of transmission. A
complete fix will be quite intrusive, but until that is available, all
IPv6 packets are identified as regular.
This patch also removes a magic number.
Reported-and-tested-by: Alan Fisher <acf@unixcube.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.18+]
Cc: Alan Fisher <acf@unixcube.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 8bfae4f993 upstream.
Sometimes while CPU have some load and ath5k doing the wireless
interface reset the whole WiSoC completely freezes. Set of tests shows
that using atomic delay function while we wait interface reset helps to
avoid such freezes.
The easiest way to reproduce this issue: create a station interface,
start continous scan with wpa_supplicant and load CPU by something. Or
just create multiple station interfaces and put them all in continous
scan.
This patch partially reverts the commit 1846ac3dbe ("ath5k: Use
usleep_range where possible"), which replaces initial udelay()
by usleep_range().
I do not know actual source of this issue, but all looks like that HW
freeze is caused by transaction on internal SoC bus, while wireless
block is in reset state.
Also I should note that I do not know how many chips are affected, but I
did not see this issue with chips, other than AR5312.
CC: Jiri Slaby <jirislaby@gmail.com>
CC: Nick Kossifidis <mickflemm@gmail.com>
CC: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Fixes: 1846ac3dbe ("ath5k: Use usleep_range where possible")
Reported-by: Christophe Prevotaux <c.prevotaux@rural-networks.com>
Tested-by: Christophe Prevotaux <c.prevotaux@rural-networks.com>
Tested-by: Eric Bree <ebree@nltinc.com>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aeb2d2a4c0 upstream.
In commit e9538cf4f9 ("rtlwifi: Fix error when accessing unmapped memory
in skb"), a printk was included to indicate that the condition had been
reached. There is now enough evidence from other users that the fix is
working. That logging statement can now be removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d4beca377 upstream.
This driver utilizes a FIFO buffer for RX descriptors. There are four places
in the code where it calculates the number of free slots. Several of those
locations do the calculation incorrectly. To fix these and to prevent future
mistakes, a common inline routine is created.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92ff754240 upstream.
The firmware supplies two kinds of packets via the RX mechanism. Besides the
normal data received over the air, these packets may contain bluetooth status
and other information. The present code fails to detect which kind of
information was received.
Signed-off-by: Troy Tan <troy_tan@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e5f443616 upstream.
Initially, the routine to update the write point in the FIFO buffer was
coded to save CPU time by not doing the calculation every interrupt. This
was an error and results in TX hangs.
Signed-off-by: Troy Tan <troy_tan@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5523d11cc4 upstream.
We don't really need to use different mac colors when adding mac
contexts, because they're not used anywhere. In fact, the firmware
doesn't accept 255 as a valid color, so we get into a SYSASSERT 0x3401
when we reach that.
Remove the color increment to use always zero and avoid reaching 255.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2cee4762c5 upstream.
These are coming from the FW and are used to access arrays.
Bad values can cause an out of bounds access so discard
such ba_notifs and warn.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd8f438405 upstream.
The base address of the scheduler in the device's memory
(SRAM) comes from two different sources. The periphery
register and the alive notification from the firmware.
We have a check in iwl_pcie_tx_start that ensures that
they are the same.
When we resume from WoWLAN, the firmware may have crashed
for whatever reason. In that case, the whole device may be
reset which means that the periphery register will hold a
meaningless value. When we come to compare
trans_pcie->scd_base_addr (which really holds the value we
had when we loaded the WoWLAN firmware upon suspend) and
the current value of the register, we don't see a match
unsurprisingly.
Trick the check to avoid a loud yet harmless WARN.
Note that when the WoWLAN has crashed, we will see that
in iwl_trans_pcie_d3_resume which will let the op_mode
know. Once the op_mode is informed that the WowLAN firmware
has crashed, it can't do much besides resetting the whole
device.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c93edc6393 upstream.
commit 5c90422439
"iwlwifi: mvm: don't allow diversity if BT Coex / TT forbid it"
broke Rx with 2 chains for diversity.
This had an impact on throughput where we're using only a single
stream (11a/b/g APs, single stream APs, static SMPS).
Fixes: 5c90422439 ("iwlwifi: mvm: don't allow diversity if BT Coex / TT forbid it")
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9538cf4f9 upstream.
These drivers use 9100-byte receive buffers, thus allocating an skb requires
an O(3) memory allocation. Under heavy memory loads and fragmentation, such
a request can fail. Previous versions of the driver have dropped the packet
and reused the old buffer; however, the new version introduced a bug in that
it released the old buffer before trying to allocate a new one. The previous
method is implemented here. The skb is unmapped before any attempt is made to
allocate another.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Eric Biggers <ebiggers3@gmail.com>
Cc: Eric Biggers <ebiggers3@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e4982f6a5 upstream.
Like with ath9k, ath5k queues also need to be ordered by priority.
queue_info->tqi_subtype already contains the correct index, so use it
instead of relying on the order of ath5k_hw_setup_tx_queue calls.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a12a07e44 upstream.
Since the commit below, iwldvm sends the FLUSH command to
the firmware. All the devices that use iwldvm have a
firmware that expects the _v3 version of this command,
besides 5150.
5150's latest available firmware still expects a _v2 version
of the FLUSH command.
This means that since the commit below, we had a mismatch for
this specific device only.
This mismatch led to the NMI below:
Loaded firmware version: 8.24.2.2
Start IWL Error Log Dump:
Status: 0x0000004C, count: 5
0x00000004 | NMI_INTERRUPT_WDG
0x000006F4 | uPc
0x000005BA | branchlink1
0x000006F8 | branchlink2
0x000008C2 | interruptlink1
0x00005B02 | interruptlink2
0x00000002 | data1
0x07030000 | data2
0x00000068 | line
0x3E80510C | beacon time
0x728A0EF4 | tsf low
0x0000002A | tsf hi
0x00000000 | time gp1
0x01BDC977 | time gp2
0x00000000 | time gp3
0x00010818 | uCode version
0x00000000 | hw version
0x00484704 | board version
0x00000002 | hcmd
0x2FF23080 | isr0
0x0103E000 | isr1
0x0000001A | isr2
0x1443FCC3 | isr3
0x11800112 | isr4
0x00000068 | isr_pref
0x000000D4 | wait_event
0x00000000 | l2p_control
0x00000007 | l2p_duration
0x00103040 | l2p_mhvalid
0x00000007 | l2p_addr_match
0x00000000 | lmpm_pmg_sel
0x00000000 | timestamp
0x00000200 | flow_handler
This was reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=88961
Fixes: a0855054e5 ("iwlwifi: dvm: drop non VO frames when flushing")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 78063d81d3 upstream.
Hardware queues are ordered by priority. Use queue index 0 for BK, which
has lower priority than BE.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad8fdccf9c upstream.
The driver passes the desired hardware queue index for a WMM data queue
in qinfo->tqi_subtype. This was ignored in ath9k_hw_setuptxqueue, which
instead relied on the order in which the function is called.
Reported-by: Hubert Feurstein <h.feurstein@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Emmanuel Grumbach <egrumbach@gmail.com> says:
"Not all the firmware know how to handle the HOT_SPOT_CMD.
Make sure that the firmware will know this command before
sending it. This avoids a firmware crash."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Older firmwares do not provide support for the HOT_SPOT_CMD command.
Check for the appropriate TLV flag that declares hotspot support in
the firmware to prevent a firmware assertion failure that can be
triggered from the userspace,
Cc: stable@vger.kernel.org [3.17+]
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This is a specific implementation, <asm/unaligned.h> is the
multiplexer that has the arch-specific knowledge of which
of the implementations needs to be used, so include that.
This issue was revealed by kbuild testing
when <asm/unaligned.h> was added in <linux/ieee80211.h>
resulting in redefinition of get_unaligned_be16 (and
probably others).
Cc: stable@vger.kernel.org # v3.17
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Return value of irq_of_parse_and_map() is unsigned int, with 0
indicating failure, so testing for negative result never works.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Cc: stable@vger.kernel.org # v3.17
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kill the submitted URB in brcmf_usb_dl_cmd if the request timed out. This
assures the URB is never submitted twice. It also prevents a possible
use-after-free of the URB transfer buffer if a timeout occurs.
Signed-off-by: Mathy Vanhoef <vanhoefm@gmail.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit that went into 3.17:
ath9k: Summarize hw state per channel context
Group and set hw state (opmode, primary_sta, beacon conf) per
channel context instead of whole list of vifs. This would allow
each channel context to run in different mode (STA/AP).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
broke multi-vif configuration due to not properly calculating
the bssid mask.
The test case that caught this was:
create wlan0 and sta0-4 (6 total), not sure how much that matters.
associate all 6 (works fine)
disconnect 5 of them, leaving sta0 up
Start trying to bring up the other 5 one at a time. It will
fail, with iw events looking like this (in these logs, several
sta are trying to come up, but symptom is the same with just one)
The patch causing the regression made quite a few changes, but
the part I think caused this particular problem was not
recalculating the bssid mask when adding and removing interfaces.
Re-adding those calls fixes my test case. Fix bad comment
as well.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on the reference clock, which could be 25MHz or 40MHz,
AR_RTC_DERIVED_CLK is programmed differently for AR9340 and AR9550.
But, when a chip reset is done, processing the initvals
sets the register back to the default value.
Fix this by moving the code in ath9k_hw_init_pll() to
ar9003_hw_override_ini(). Also, do this override for AR9531.
Cc: stable@vger.kernel.org
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function chandef_to_chanspec() failed when converting a
chandef with bandwidth set to NL80211_CHAN_WIDTH_20_NOHT. This
was reported by user running the device in AP mode.
------------[ cut here ]------------
WARNING: CPU: 0 PID: 304 at
drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c:381
chandef_to_chanspec.isra.11+0x158/0x184()
Modules linked in:
CPU: 0 PID: 304 Comm: hostapd Not tainted 3.16.0-rc7-abb+g64aa90f #8
[<c0014bb4>] (unwind_backtrace) from [<c0012314>] (show_stack+0x10/0x14)
[<c0012314>] (show_stack) from [<c001d3f8>] (warn_slowpath_common+0x6c/0x8c)
[<c001d3f8>] (warn_slowpath_common) from [<c001d4b4>] (warn_slowpath_null+0x1c/0x24)
[<c001d4b4>] (warn_slowpath_null) from [<c03449a4>] (chandef_to_chanspec.isra.11+0x158/0x184)
[<c03449a4>] (chandef_to_chanspec.isra.11) from [<c0348e00>] (brcmf_cfg80211_start_ap+0x1e4/0x614)
[<c0348e00>] (brcmf_cfg80211_start_ap) from [<c04d1468>] (nl80211_start_ap+0x288/0x414)
[<c04d1468>] (nl80211_start_ap) from [<c043d144>] (genl_rcv_msg+0x21c/0x38c)
[<c043d144>] (genl_rcv_msg) from [<c043c740>] (netlink_rcv_skb+0xac/0xc0)
[<c043c740>] (netlink_rcv_skb) from [<c043cf14>] (genl_rcv+0x20/0x34)
[<c043cf14>] (genl_rcv) from [<c043c0a0>] (netlink_unicast+0x150/0x20c)
[<c043c0a0>] (netlink_unicast) from [<c043c4b8>] (netlink_sendmsg+0x2b8/0x398)
[<c043c4b8>] (netlink_sendmsg) from [<c04066a4>] (sock_sendmsg+0x84/0xa8)
[<c04066a4>] (sock_sendmsg) from [<c0407c5c>] (___sys_sendmsg.part.29+0x268/0x278)
[<c0407c5c>] (___sys_sendmsg.part.29) from [<c0408bdc>] (__sys_sendmsg+0x4c/0x7c)
[<c0408bdc>] (__sys_sendmsg) from [<c000ec60>] (ret_fast_syscall+0x0/0x44)
---[ end trace 965ee2158c9905a2 ]---
Cc: stable@vger.kernel.org # v3.17
Reported-by: Pontus Fuchs <pontusf@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RT2800 and newer hardware require padding between header and payload if
header length is not multiple of 4.
For historical reasons we also align payload to to 4 bytes boundary, but
such alignment is not needed on modern H/W.
Patch fixes skb_under_panic problems reported from time to time:
https://bugzilla.kernel.org/show_bug.cgi?id=84911https://bugzilla.kernel.org/show_bug.cgi?id=72471http://marc.info/?l=linux-wireless&m=139108549530402&w=2https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1087591
Panic happened because we eat 4 bytes of skb headroom on each
(re)transmission when sending frame without the payload and the header
length not being multiple of 4 (i.e. QoS header has 26 bytes). On such
case because paylad_aling=2 is bigger than header_align=0 we increase
header_align by 4 bytes. To prevent that we could change the check to:
if (payload_length && payload_align > header_align)
header_align += 4;
but not aligning payload at all is more effective and alignment is not
really needed by H/W (that has been tested on OpenWrt project for few
years now).
Reported-and-tested-by: Antti S. Lankila <alankila@bel.fi>
Debugged-by: Antti S. Lankila <alankila@bel.fi>
Reported-by: Henrik Asp <solenskiner@gmail.com>
Originally-From: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach <egrumbach@gmail.com> says:
"Two fixes here - we weren't updating mac80211 if a scan
was cut short by RFKILL which confused cfg80211. As a
result, the latter wouldn't allow to run another scan.
Liad fixes a small bug in the firmware dump."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The length counting previously done had an error in it, causing
the length down the data dumping function to be shorter than it
should be, causing the end of the data to get truncated off and
lost.
Cc: <stable@vger.kernel.org> [3.17+]
Fixes: 67c65f2cf7 ("iwlwifi: dump periphery registers to fw-error-dump")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
phy_read and phy_write are not set for every phy any more sine this:
commit d342b95dd7
Author: Rafał Miłecki <zajec5@gmail.com>
Date: Thu Jul 31 21:59:43 2014 +0200
b43: don't duplicate common PHY read/write ops
b43_phy_copy() accesses phy_read and phy_write directly and will fail
with some phys. This patch fixes the regression by using the
b43_phy_read() and b43_phy_write() functions which should be used for
read and write access.
This should fix this bug report:
https://bugzilla.kernel.org/show_bug.cgi?id=87731
Reported-by: Volker Kempter <v.kempter@pe.tu-clausthal.de>
Tested-by: Volker Kempter <v.kempter@pe.tu-clausthal.de>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changes in the vendor driver were added to rtlwifi, but some updates
to rtl8192se were missed, and the driver could neither scan nor connect.
There are other changes that will enhance performance, but this minimal
set fix the basic functionality.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are typos in the handling of the descriptor pointers where the wrong
descriptor is referenced. There is also an error in which the pointer is
incremented twice.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Device RTL8192EE uses a new form of trx flow. This fix sets up the descriptors
correctly.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg <johannes@sipsolutions.net> says:
"This contains another small set of fixes for 3.18, these are all
over the place and most of the bugs are old, one even dates back
to the original mac80211 we merged into the kernel."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach <egrumbach@gmail.com> says:
"I fix here two issues that are related to the firmware
loading flow. A user reported that he couldn't load the
driver because the rfkill line was pulled up while we
were running the calibrations. This was happening while
booting the system: systemd was restoring the "disable
wifi settings" and that raised an RFKILL interrupt during
the calibration. Our driver didn't handle that properly
and this is now fixed."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
