"lm75" without any vendor is undocumented. It works with the Linux
kernel since the I2C subsystem will do matches of the compatible string
without a vendor prefix to the i2c_device_id and/or driver name.
Mostly replace "lm75" with "national,lm75" as that's the original part
vendor and the compatible which matches what "lm75" matched with. In a
couple of cases the node name or compatible gives a clue to the actual
part and vendor and a more specific compatible can be used. In these
cases, it does change the variant the kernel picks.
"nct75" is an OnSemi part which is compatible with TI TMP75C based on
a comparison of the OnSemi NCT75 datasheet and configuration the Linux
driver uses. Adding an OnSemi compatible would be an ABI change.
"nxp,lm75" is most likely an NXP part. Alexander Stein says the i.MX53
boards are a NXP LM75A as well. NXP makes a LM75A and LM75B. Both are
11-bit resolution and 100ms sample time. The "national,lm75a" is
9-bit, so "national,lm75b" is the closest match for both NXP variants.
While we're here, fix the node names to use the generic name
"temperature-sensor".
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com> # am335x-nano.dts
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com> # imx53-mba53.dts, imx53-tqma53.dtsi
Link: https://lore.kernel.org/r/20240816164717.1585629-1-robh@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Bindings expect NAND controller node name to match certain patterns:
socfpga_arria10_socdk_nand.dtb: nand@ffb90000: $nodename:0: 'nand@ffb90000' does not match '^nand-controller(@.*)?'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
cdns,page-size and cdns,block-size are neither documented nor used by
Linux, so remove them to fix dtbs_check warnings like:
socfpga_arria5_socdk.dtb: flash@0: Unevaluated properties are not allowed ('cdns,block-size', 'cdns,page-size' were unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
The "stmmaceth-ocp" reset line on the SoCFPGA stmmac ethernet driver is
the same as the "ahb" reset on a standard stmmac ethernet.
commit ("843f603762a5 dt-bindings: net: snps,dwmac: Add 'ahb'
reset/reset-name") documented the second reset signal as 'ahb' instead
of 'stmmaceth-ocp'. Change the reset-names of the SoCFPGA DWMAC driver to
'ahb'. In order not to break ABI, we will keep support in thedwmac-socfpga
driver to still make use of "stmmaceth-ocp".
This also fixes the dtbs_check warning:
ethernet@ff802000: reset-names:1: 'ahb' was expected
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
---
v2: update commit message to further describe the reason for the change
