If the nominal VBlank is too small, optimizing for stutter can cause
the prefetch bandwidth to increase drasticaly, resulting in higher
clock and power requirements. Only optimize if it is >3x the stutter
latency.
Reviewed-by: Austin Zheng <austin.zheng@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 003215f962)
Cc: stable@vger.kernel.org
[Why]
In the case where a dml allocation fails for any reason, the
current state's dml contexts would no longer be valid. Then
subsequent calls dc_state_copy_internal would shallow copy
invalid memory and if the new state was released, a double
free would occur.
[How]
Reset dml pointers in new_state to NULL and avoid invalid
pointer
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Ryan Seto <ryanseto@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit bcafdc6152)
Cc: stable@vger.kernel.org
[Why]
Since the surface/stream update flags aren't cleared after applying
updates, those same updates may be applied again in a future call to
update surfaces/streams for surfaces/streams that aren't actually part
of that update (i.e. applying an update for one surface/stream can
trigger unintended programming on a different surface/stream).
For example, when an update results in a call to
program_front_end_for_ctx, that function may call program_pipe on all
pipes. If there are surface update flags that were never cleared on the
surface some pipe is attached to, then the same update will be
programmed again.
[How]
Clear the surface and stream update flags after applying the updates.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3441
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3616
Cc: Melissa Wen <mwen@igalia.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 7671f62c10)
Cc: stable@vger.kernel.org
Correct the parameter descriptor for the function
`dc_process_dmub_dpia_set_tps_notification` to match the actual
parameters used.
Fixes the below with gcc W=1:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:5768: warning: Function parameter or struct member 'tps' not described in 'dc_process_dmub_dpia_set_tps_notification'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:5768: warning: Excess function parameter 'ts' description in 'dc_process_dmub_dpia_set_tps_notification'
Cc: Tom Chung <chiahsuan.chung@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Roman Li <roman.li@amd.com>
Cc: Alex Hung <alex.hung@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As set_drr() is called from IRQ context, it can happen that the
pipe context has been nulled by dc_state_destruct().
Apply the same protection here that is already present for
dcn35_set_drr() and dcn10_set_drr(). I.e. fetch the tg pointer
first (to avoid a race with dc_state_destruct()), and then
check the local copy before using it.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3142
Fixes: 06ad7e1642 ("drm/amd/display: Destroy DC context while keeping DML and DML2")
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Clear cached watermark after resume
- Update IPS default mode for DCN35/DCN351
- Use full update for swizzle mode change
- Skip to enable dsc if it has been off
- Fix underflow when setting underscan on DCN401
- Remove always-false branches
- Check null pointer before dereferencing se
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
1) We did linear/non linear transition properly long ago
2) We used that path to handle SystemDisplayEnable
3) We fixed a SystemDisplayEnable inability to fallback to passive by
impacting the transition flow generically
4) AFMF later relied on the generic transition behavior
Separating the two flows to make (3) non-generic is the best immediate
coarse of action.
DC can discern SSAMPO3 very easily from SDE.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Chris Park <chris.park@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
It makes DSC enable when we commit the stream which need
keep power off, and then it will skip to disable DSC if
pipe reset at this situation as power has been off. It may
cause the DSC unexpected enable on the pipe with the
next new stream which doesn't support DSC.
[HOW]
Check the DSC used on current pipe status when update stream.
Skip to enable if it has been off. The operation enable
DSC should happen when set power on.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Zhikai Zhai <zhikai.zhai@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
req128_c is always set to false and its branch is never taken.
Similarly, MacroTileSizeBytes is set to either 256 or 65535 and it is
never 4096 and it's branch is not taken.
Therefore, their branches are removed.
This fixes 3 DEADCODE issues reported by Coverity.
Acked-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
se is null checked previously in the same function, indicating
it might be null; therefore, it must be checked when used again.
This fixes 1 FORWARD_NULL issue reported by Coverity.
Acked-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We intend to consolidate dp tunneling and conventional dp link training.
[HOW]
1. Use the same link training entry for both dp and dpia
2. Move SET_CONFIG of non-transparent mode to dmub side
3. Add set_tps_notification dmub_cmd to notify tps request for
non-transparent dpia link training
4. Check dpcd request result and abort link training early if dpia
aux tunneling fails
5. Add option to avoid affect old product
6. Separately handle wait_time_microsec for dpia
Reviewed-by: Cruise Hung <cruise.hung@amd.com>
Reviewed-by: George Shen <george.shen@amd.com>
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DSC on eDP could be enabled during VBIOS post. The enabled
DSC may not be disabled when enter to OS, once the system was
in second screen only mode before entering to S4. In this
case, OS will not send setTimings to reset eDP path again.
The enabled DSC HW will make a new stream without DSC cannot
output normally if it reused this pipe with enabled DSC.
[HOW]
In accelerated mode, to clean up DSC blocks if eDP is on link
but not active when we are not in fast boot and seamless boot.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Add options to change sharpen policy based on surface format
and scaling ratios.
[HOW]
Add sharpen_policy to change policy based on surface format
and scale_to_sharpness_policy based on scaling ratios.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Driver reports 0 display when the virtual display is still present, and
causes P-state hang in FW.
[HOW]
When enumerating through streams, check for active planes and use that
to indicate number of displays.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Daniel Sa <Daniel.Sa@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
There are some monitor timings that seem to be supported without
DSC but actually require DSC to be displayed. A VESA SCR introduced
a new max uncompressed pixel rate cap register that we can use to
handle these edge cases.
[HOW]
SST: Read caps from link and invalidate timings that exceed the
max limit but do not support DSC. Then check for options override
when determining BPP.
MST: Read caps from virtual DPCD peer device or daisy chained SST
monitor and set validation set BPPs to max if pixel rate exceeds
uncompressed limit. Validation set optimization continues as normal.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Ryan Seto <ryanseto@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Correctly spelled comments make it easier for the reader to understand
the code.
Replace 'maxium' with 'maximum' in the comment &
replace 'diffculty' with 'difficulty' in the comment &
replace 'suppluy' with 'supply' in the comment &
replace 'Congiuration' with 'Configuration' in the comment &
replace 'eanbled' with 'enabled' in the comment.
Signed-off-by: Yan Zhen <yanzhen@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
enable dpp rcg before we disable dppclk in hw_init cause system
hang/reboot
[How]
we remove dccg rcg related code from init into a separate function and
call it after we init pipe
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Qili Lu <qili.lu@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Function used to check the number of FEs connected to the current BE.
This was then used to determine if the symclk could be disabled, if
all FEs were disconnected. However, the function would skip over the
primary FE and return 0 when the primary FE was still connected. This
caused black screens on driver disable with an MST daisy chain hooked
up.
[How]
Refactor the function to correctly return the number of FEs connected
to the input BE. Also, rename it for clarity.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Nicholas Susanto <Nicholas.Susanto@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dc_state_destruct() nulls the resource context of the DC state. The pipe
context passed to dcn35_set_drr() is a member of this resource context.
If dc_state_destruct() is called parallel to the IRQ processing (which
calls dcn35_set_drr() at some point), we can end up using already nulled
function callback fields of struct stream_resource.
The logic in dcn35_set_drr() already tries to avoid this, by checking tg
against NULL. But if the nulling happens exactly after the NULL check and
before the next access, then we get a race.
Avoid this by copying tg first to a local variable, and then use this
variable for all the operations. This should work, as long as nobody
frees the resource pool where the timing generators live.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3142
Fixes: 06ad7e1642 ("drm/amd/display: Destroy DC context while keeping DML and DML2")
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dc_state_destruct() nulls the resource context of the DC state. The pipe
context passed to dcn10_set_drr() is a member of this resource context.
If dc_state_destruct() is called parallel to the IRQ processing (which
calls dcn10_set_drr() at some point), we can end up using already nulled
function callback fields of struct stream_resource.
The logic in dcn10_set_drr() already tries to avoid this, by checking tg
against NULL. But if the nulling happens exactly after the NULL check and
before the next access, then we get a race.
Avoid this by copying tg first to a local variable, and then use this
variable for all the operations. This should work, as long as nobody
frees the resource pool where the timing generators live.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3142
Fixes: 06ad7e1642 ("drm/amd/display: Destroy DC context while keeping DML and DML2")
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Tested-by: Raoul van Rüschen <raoul.van.rueschen@gmail.com>
Tested-by: Christopher Snowhill <chris@kode54.net>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Tested-by: Sefa Eyeoglu <contact@scrumplex.net>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commit addresses a missing kdoc for the 'bs_coeffs_updated'
parameter in the 'dpp401_dscl_program_isharp' function. The
'bs_coeffs_updated' is a flag indicating whether the Blur and Scale
Coefficients have been updated.
The 'dpp401_dscl_program_isharp' function is responsible for programming
the isharp, which includes setting the isharp filter, noise gain, and
blur and scale coefficients. If the 'bs_coeffs_updated' flag is set to
true, the function updates the blur and scale coefficients.
Fixes the below with gcc W=1:
drivers/gpu/drm/amd/amdgpu/../display/dc/dpp/dcn401/dcn401_dpp_dscl.c:961: warning: Function parameter or struct member 'bs_coeffs_updated' not described in 'dpp401_dscl_program_isharp'
Cc: Tom Chung <chiahsuan.chung@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Roman Li <roman.li@amd.com>
Cc: Alex Hung <alex.hung@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Suggested-by: Tom Chung <chiahsuan.chung@amd.com>
Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[what]
Graphics hang observed with 3 displays connected to DP2.0 mst dock.
[why]
There's a mismatch in dml and dc between the assignments of hpo link
encoders.
[how]
Add a new array in dml that tracks the current mapping of HPO stream
encoders to HPO link encoders in dc.
Reviewed-by: Sung joon Kim <sungjoon.kim@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Gabe Teeger <Gabe.Teeger@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Add interface for controlling shapness level input into DCN.
- Update SPL to support custom sharpness values.
- Add support for different sharpness values depending on YUV/RGB
content.
Reviewed-by: Samson Tam <samson.tam@amd.com>
Signed-off-by: Relja Vojvodic <Relja.Vojvodic@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Certain profiles have higher HDR multiplier than SDR boost max which
is not currently supported
[How]
Disable sharpness for these profiles
Fixes: 1b0ce903fe ("drm/amd/display: add improvements for text display and HDR DWM and MPO")
Reviewed-by: Martin Leung <martin.leung@amd.com>
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To provide option to dpia control power management
[How]
By adding disable_usb4_pm_support bit field in dpia_debug option to
control dpia power management
Reviewed-by: Jun Lei <jun.lei@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previous disable ODM policy due to underflow issue with sharpener.
Issue is resolved after updating sharpening policy to apply to
both windowed and fullscreen video
[How]
Remove sharpness check disabling Dynamic ODM policy
Reviewed-by: Martin Leung <martin.leung@amd.com>
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some asserts are always hit on startup/Pnp when they should only be used
to indicate when something has gone wrong.
[How]
Ignore result of getting function from bios cmd table for newer asics.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Signed-off-by: Daniel Sa <Daniel.Sa@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Setting min dispclk to 50Mhz outside clock lowering function causes
unnecessary calls to SMU to lower dispclk and causes dentist hangs when
there is no stream on the pipes.
[How]
Move the set minimum dispclk logic inside the lowering dispclk if
statement.
Fixes: 2344413205 ("DCN35 set min dispclk to 50Mhz")
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Nicholas Susanto <Nicholas.Susanto@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
