[WHY]
We intend to consolidate dp tunneling and conventional dp link training.
[HOW]
1. Use the same link training entry for both dp and dpia
2. Move SET_CONFIG of non-transparent mode to dmub side
3. Add set_tps_notification dmub_cmd to notify tps request for
non-transparent dpia link training
4. Check dpcd request result and abort link training early if dpia
aux tunneling fails
5. Add option to avoid affect old product
6. Separately handle wait_time_microsec for dpia
Reviewed-by: Cruise Hung <cruise.hung@amd.com>
Reviewed-by: George Shen <george.shen@amd.com>
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
There are some monitor timings that seem to be supported without
DSC but actually require DSC to be displayed. A VESA SCR introduced
a new max uncompressed pixel rate cap register that we can use to
handle these edge cases.
[HOW]
SST: Read caps from link and invalidate timings that exceed the
max limit but do not support DSC. Then check for options override
when determining BPP.
MST: Read caps from virtual DPCD peer device or daisy chained SST
monitor and set validation set BPPs to max if pixel rate exceeds
uncompressed limit. Validation set optimization continues as normal.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Ryan Seto <ryanseto@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Supporting UHBR10 link rate on eDP leverages
the existing DP2.0 code but need to add some small
adjustments in code.
[how]
Acknowledge the given DPCD caps for UHBR10
link rate support and allow DP2.0 programming
sequence and link training for eDP.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Sung Joon Kim <Sungjoon.Kim@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
eDP 2.0 is introducing support for UHBR link rates, however current eDP ILR
link optimization does not account for UHBR capabilities.
Either UHBR capabilities will be provided via the same 128b/132b rate DPCD caps
that are currently used on DP2.1, or Table 4-13 may be updated to include UHBR
rates.
[HOW]
Add extra Supported Link Rates table translations for UHBR10/13.5/20.
Update eDP link setting optimization search to be aware of 128b/132b DPCD
rate caps in order to unblock UHBR on panels with Supported Link Rates table.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Under autonomous mode, source reads dpcd DP_PCON_HDMI_POST_FRL_STATUS
for the frl link status.
Without dsc passthrough, it serves as bw bottleneck on the entire link,
compared with the dp link from source to the converter where dsc is
available.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
Poniters, such as dc->clk_mgr, are null checked previously in the same
function, so Coverity warns "implies that "dc->clk_mgr" might be null".
As a result, these pointers need to be checked when used again.
This fixes 10 FORWARD_NULL issues reported by Coverity.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When assert in dp_retrieve_lttpr_cap() is hit, dmesg has traces like:
RIP: 0010:dp_retrieve_lttpr_cap+0xcc/0x1a0 [amdgpu]
Call Trace:
<TASK>
dp_retrieve_lttpr_cap+0xcc/0x1a0 [amdgpu]
report_bug+0x1e8/0x240
handle_bug+0x46/0x80
link_detect+0x35/0x580 [amdgpu]
It happens when LTTPRs fail to increment dpcd repeater count.
We have a recovery action in place for such cases.
Assert is misleading, an indicative error in dmesg is more useful.
[How]
Remove ASSERT and use DC_LOG_ERROR instead.
Reviewed-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
Integer multiplies integer may overflow in context that expects an
expression of unsigned/siged long long (64 bits). This can be fixed
by casting integer to unsigned/siged long long to force 64 bits results.
This fixes 26 OVERFLOW_BEFORE_WIDEN issues reported by Coverity.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
Function return values must be checked before data can be used
in subsequent functions.
This fixes 4 CHECKED_RETURN issues reported by Coverity.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Coverity analysis of the Upstream display driver code
(amd-staging-drm-next) flagged these three functions as
containing 'CONSTANT_EXPRESSION_RESULT' errors, i. e. the
conditionals are reduntant since their result is predetermined.
fixpt31_32.c:
The two flagged 'ASSERT' lines redundant since they are always true:
- LONG_MAX equals to the largest 'signed long long' number
- res.value is type 'signed long long',
So, the condition inside the 'ASSERTS's is always
link_dp_training.c:
The flagged conditional statement is always false:
- 'max_requested.FFE_PRESET.settings.level' is 4 bits, so its max
possible value is 15
- 'DP_FFE_PRESET_MAX_LEVEL' equals to 15.
So, the conditional statement is always false and the wrapped code
never executes.
[HOW]
Removed lines flagged by Coverity analysis.
Reviewed-by: Sun peng Li <sunpeng.li@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Ivan Lipski <ivlipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
We set preferred link settings for virtual signal. However we don't support
virtual signal for UHBR link rate. If preferred is set to UHBR link rate, we
will allow virtual signal with UHBR link rate which causes system crashes.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Passive DP40 cables were updated in the latest DP spec to support
UHBR13.5 link rate. Current max link rate logic checks against the
cable ID DPCD even for passive cables.
[How]
Ignore UHBR13.5 cable ID DPCD cap in get_max_link_rate logic.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Some sinks are observed to return invalid LTTPR revision and/or invalid
LTTPR link rate capabilities.
[HOW]
Assume any LTTPR which reports invalid max link rate supports HBR3.
Don't validate LTTPR DPCD revision in dp_is_lttpr_present check.
Reviewed-by: George Shen <george.shen@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently there's an issue on DCN401 that prevents oled eDP panels from
being lit up that is still under investigation. To unblock dev work
while investigating, we can work around the issue by skipping toggling
the enablement of the backlight.
[How]
- new debug bit that will skip touching backlight enable DPCD for oled
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In order to support glitchless display clock ramping for virtual stream,
we must
turn on symclk for stream encoder. The code will power on phy and enable
symclk
for dio encoder during virtual stream dpms sequence.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
'aux_payloads' is unused since
commit eae5ffa9bd ("drm/amd/display: Switch ddc to new aux interface")
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When the link BW is smaller than the request BW,
the DP LT just kept running and fallback to lower link config.
DP LT just aborted if is_hpd_pending bit is high.
But is_hpd_pending bit indicates a new HPD event received.
It doesn't mean the HPD is low.
[How]
Abort the DP LT if the link BW is smaller than the request BW.
Remove checking is_hpd_pending bit in DP LT.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Cruise <cruise.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
UHBR13.5 support is optional, even if UHBR20 is supported by the device.
If source supports max UHBR13.5 while sink, cable and LTTPR support
UHBR20 but not UHBR13.5, UHBR10 should be used as the max link cap.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For addtion (uint8_t) variable + constant 1,
coverity generates message below:
Truncation due to cast operation on "cur_idx + 1" from
32 to 8 bits.
Then Coverity assume result is 32 bits value be saved into
8 bits variable. When result is used as index to access
array, Coverity suspects index invalid.
[How]
Change varaible type to uint32_t.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During DP tunnel creation, CM preallocates BW and reduces
estimated BW of other DPIA. CM release preallocation only
when allocation is complete. Display mode validation logic
validates timings based on bw available per host router.
In multi display setup, this causes bw allocation failure
when allocation greater than estimated bw.
[How]
Do zero alloc to make the CM to release preallocation and
update estimated BW correctly for all DPIAs per host router.
Reviewed-by: PeiChen Huang <peichen.huang@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
TCON data is corrupted after electro static discharge test.
Once the TCON data get corrupted, they will get themselves
reset and send HPD_IRQ to source side.
[How]
Support HPD_IRQ for internal link, and restore the PSR/Replay setup.
Reviewed-by: Robin Chen <robin.chen@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Sung-huai Wang <danny.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Enabling higher compiler warning levels results in many issues that can
be trivially resolved as well as some potentially critical issues.
[how]
Fix all compiler warnings found with various compilers and higher
warning levels. Primarily, potentially uninitialized variables and
unreachable code.
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The function to count the number of valid connectors does not
guarantee that the first n indices are valid, only that there
exist n valid indices. When invalid indices are present, this
results in later valid connectors being missed, as processing
would end after checking n indices.
[How]
- count valid indices separately from total indices examined
- add explicit definition of MAX_LINKS
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Dmub provides several Replay residency calculation methods,
but current interface only supports either ALPM or PHY mode
[How]
Modify the interface for supporting different types
of Replay residency calculation.
Reviewed-by: Robin Chen <robin.chen@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Leon Huang <leon.huang1@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In the first if statement, we're checking if 'replay' is NULL. But in
the second if statement, we're not checking if 'replay' is NULL again
before calling replay->funcs->replay_set_power_opt().
if (replay == NULL && force_static)
return false;
...
if (link->replay_settings.replay_feature_enabled &&
replay->funcs->replay_set_power_opt) {
replay->funcs->replay_set_power_opt(replay, *power_opts, panel_inst);
link->replay_settings.replay_power_opt_active = *power_opts;
}
If 'replay' is NULL, this will cause a null pointer dereference.
Fixes the below found by smatch:
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_edp_panel_control.c:895 edp_set_replay_allow_active() error: we previously assumed 'replay' could be null (see line 887)
Fixes: c7ddc0a800 ("drm/amd/display: Add Functions to enable Freesync Panel Replay")
Cc: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Cc: Roman Li <roman.li@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Tom Chung <chiahsuan.chung@amd.com>
Suggested-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Need to fix some broken logic and sequencing in initial commit
[HOW]
Fix logic handling override deprogramming when exiting SQ128.
Don't exit early from dp_set_hw_lane_settings for DP2/FIXED_VS case.
Move LTTPR 128b/132b check out of requires_hwss and check during
runtime, as LTTPR caps are not populated on initial call.
Add pending_test_pattern to link state to allow HWSS to set FFE overrides
on retimer TX and/or skip setting APU TX FFE depending on requested pattern.
Use updated clock source for SQ128 override sequence.
Skip HW FFE preset programming when performing test pattern overrides.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
wait_time_microsec = max(wait_time_microsec, (uint32_t)
DPIA_CLK_SYNC_DELAY);
Above line is trying to assign the maximum value between
'wait_time_microsec' and 'DPIA_CLK_SYNC_DELAY' to wait_time_microsec.
However, 'wait_time_microsec' has not been assigned a value before this
line, initialize 'wait_time_microsec' at the point of declaration.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dp_training_dpia.c:697 dpia_training_eq_non_transparent() error: uninitialized symbol 'wait_time_microsec'.
Fixes: 630168a973 ("drm/amd/display: move dp link training logic to link_dp_training")
Cc: Wenjing Liu <wenjing.liu@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Roman Li <roman.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Only required if FIXED_VS retimer does not support DP2-capable.
[HOW]
Gate link rate toggle with DP 128b/132b LTTPR channel coding cap check.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The New sequence has been in use in DCN314 with no regressions
introduced. Therefore, it is safe to enable this sequence for all
devices using FIXED_VS retimers. So, remove the legacy codepath and its
associated config flag.
Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The error message buffer overflow 'dc->links' 12 <= 12 suggests that the
code is trying to access an element of the dc->links array that is
beyond its bounds. In C, arrays are zero-indexed, so an array with 12
elements has valid indices from 0 to 11. Trying to access dc->links[12]
would be an attempt to access the 13th element of a 12-element array,
which is a buffer overflow.
To fix this, ensure that the loop does not go beyond the last valid
index when accessing dc->links[i + 1] by subtracting 1 from the loop
condition.
This would ensure that i + 1 is always a valid index in the array.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dp_dpia_bw.c:208 get_host_router_total_dp_tunnel_bw() error: buffer overflow 'dc->links' 12 <= 12
Fixes: 59f1622a5f ("drm/amd/display: Add dpia display mode validation logic")
Cc: PeiChen Huang <peichen.huang@amd.com>
Cc: Aric Cyr <aric.cyr@amd.com>
Cc: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The 'status' variable in 'core_link_read_dpcd()' &
'core_link_write_dpcd()' was uninitialized.
Thus, initializing 'status' variable to 'DC_ERROR_UNEXPECTED' by default.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dpcd.c:226 core_link_read_dpcd() error: uninitialized symbol 'status'.
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dpcd.c:248 core_link_write_dpcd() error: uninitialized symbol 'status'.
Cc: stable@vger.kernel.org
Cc: Jerry Zuo <jerry.zuo@amd.com>
Cc: Jun Lei <Jun.Lei@amd.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
