Rework the pm8008 driver to match the new devicetree binding which no
longer describes internal details like interrupts and register offsets
(including which of the two consecutive I2C addresses the registers
belong to).
Instead make the interrupt controller implementation internal and pass
interrupts to the subdrivers using MFD cell resources.
Note that subdrivers may either get their resources, like register block
offsets, from the parent MFD or this can be included in the subdrivers
directly.
In the current implementation, the temperature alarm driver is generic
enough to just get its base address and alarm interrupt from the parent
driver, which already uses this information to implement the interrupt
controller.
The regulator driver, however, needs additional information like parent
supplies and regulator characteristics so in that case it is easier to
just augment its table with the regulator register base addresses.
Similarly, the current GPIO driver already holds the number of pins and
that lookup table can therefore also be extended with register offsets.
Note that subdrivers can now access the two regmaps by name, even if the
primary regmap is registered last so that it is returned by default when
no name is provided in lookups.
Finally, note that the temperature alarm and GPIO subdrivers need some
minor rework before they can be used with non-SPMI devices like the
PM8008. The temperature alarm MFD cell name specifically uses a "qpnp"
rather than "spmi" prefix to prevent binding until the driver has been
updated.
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240608155526.12996-11-johan+linaro@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230714174731.4059811-1-robh@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Prior to commit af503716ac ("i2c: core: report OF style module alias
for devices registered via OF") drivers using OF matching needed an i2c
module alias such as "i2c:pm8008" for module autoloading to work.
Drop the bogus i2c alias from the pm8008 driver which was merged long
after i2c core was fixed and whose alias did not match the driver name
("pm8008") to begin with.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230526091646.17318-3-johan+linaro@kernel.org
Remove pm8008_init(), which according to the comments exists only
as a workaround for regmap-irq's odd treatment of type registers.
This workaround shouldn't be needed anymore because this driver
uses config registers, which are always programmed by regmap-irq
no matter what the initial register state is.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230216222214.138671-5-aidanmacdonald.0x0@gmail.com
The usual behavior of mask registers is writing a '1' bit to
disable (mask) an interrupt; similarly, writing a '1' bit to
an unmask register enables (unmasks) an interrupt.
Due to a longstanding issue in regmap-irq, mask and unmask
registers were inverted when both kinds of registers were
present on the same chip, ie. regmap-irq actually wrote '1's
to the mask register to enable an IRQ and '1's to the unmask
register to disable an IRQ.
This was fixed by commit e8ffb12e7f ("regmap-irq: Fix
inverted handling of unmask registers") but the fix is opt-in
via mask_unmask_non_inverted = true because it requires manual
changes for each affected driver. The new behavior will become
the default once all drivers have been updated.
The PM8008 appears to rely on the inverted behavior. It has
separate set & clear registers for a register called INT_EN,
which presumably enables interrupts by writing '1's. Opt in
to the new non-inverted behavior & swap mask_base/unmask_base.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230216222214.138671-2-aidanmacdonald.0x0@gmail.com
Maintaining a local driver data structure that is never shared
outside of the core device is an unnecessary complexity. Half of the
attributes were not used outside of a single function, one of which
was not used at all. The remaining 2 are generic and can be passed
around as required.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Qualcomm Technologies, Inc. PM8008 is a dedicated camera PMIC that
integrates all the necessary power management, housekeeping, and
interface support functions into a single IC. Its key features include
overtemperature protection, low-dropout linear regulators, GPIOs, and an
I2C interface.
Add an MFD driver to support it.
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
