asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
Pull tty / serial driver updates from Greg KH:
"Here is the "big" set of tty/serial driver updates for 6.12-rc1.
Nothing major in here, just nice forward progress in the slow cleanup
of the serial apis, and lots of other driver updates and fixes.
Included in here are:
- serial api updates from Jiri to make things more uniform and sane
- 8250_platform driver cleanups
- samsung serial driver fixes and updates
- qcom-geni serial driver fixes from Johan for the bizarre UART
engine that that chip seems to have. Hopefully it's in a better
state now, but hardware designers still seem to come up with more
ways to make broken UARTS 40+ years after this all should have
finished.
- sc16is7xx driver updates
- omap 8250 driver updates
- 8250_bcm2835aux driver updates
- a few new serial driver bindings added
- other serial minor driver updates
All of these have been in linux-next for a long time with no reported
problems"
* tag 'tty-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (65 commits)
tty: serial: samsung: Fix serial rx on Apple A7-A9
tty: serial: samsung: Fix A7-A11 serial earlycon SError
tty: serial: samsung: Use bit manipulation macros for APPLE_S5L_*
tty: rp2: Fix reset with non forgiving PCIe host bridges
serial: 8250_aspeed_vuart: Enable module autoloading
serial: qcom-geni: fix polled console corruption
serial: qcom-geni: disable interrupts during console writes
serial: qcom-geni: fix console corruption
serial: qcom-geni: introduce qcom_geni_serial_poll_bitfield()
serial: qcom-geni: fix arg types for qcom_geni_serial_poll_bit()
soc: qcom: geni-se: add GP_LENGTH/IRQ_EN_SET/IRQ_EN_CLEAR registers
serial: qcom-geni: fix false console tx restart
serial: qcom-geni: fix fifo polling timeout
tty: hvc: convert comma to semicolon
mxser: convert comma to semicolon
serial: 8250_bcm2835aux: Fix clock imbalance in PM resume
serial: sc16is7xx: convert bitmask definitions to use BIT() macro
serial: sc16is7xx: fix copy-paste errors in EFR_SWFLOWx_BIT constants
serial: sc16is7xx: remove SC16IS7XX_MSR_DELTA_MASK
serial: xilinx_uartps: Make cdns_rs485_supported static
...
0x7d and 0x7e bytes are meant to be escaped in the data portion of
frames, but this didn't occur since next_chunk_len() had an off-by-one
error. That also resulted in the final byte of a payload being written
as a separate tty write op.
The chunk prior to an escaped byte would be one byte short, and the
next call would never test the txpos+1 case, which is where the escaped
byte was located. That meant it never hit the escaping case in
mctp_serial_tx_work().
Example Input: 01 00 08 c8 7e 80 02
Previous incorrect chunks from next_chunk_len():
01 00 08
c8 7e 80
02
With this fix:
01 00 08 c8
7e
80 02
Cc: stable@vger.kernel.org
Fixes: a0c2ccd9b5 ("mctp: Add MCTP-over-serial transport binding")
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test various edge cases of inputs that contain characters
that need escaping.
This adds a new kunit suite for mctp-serial.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we encounter an error on i2c packet transmit, we won't have a valid
flow anymore; since we didn't transmit a valid packet sequence, we'll
have to wait for the key to timeout instead of dropping it on the reply.
This causes the i2c lock to be held for longer than necessary.
Instead, invalidate the flow on TX error, and release the i2c lock
immediately.
Cc: Bonnie Lo <Bonnie_Lo@wiwynn.com>
Tested-by: Jerry C Chen <Jerry_C_Chen@wiwynn.com>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provides MCTP network transport over an I3C bus, as specified in
DMTF DSP0233.
Each I3C bus (with "mctp-controller" devicetree property) gets an
"mctpi3cX" net device created. I3C devices are reachable as remote
endpoints through that net device. Link layer addressing uses the
I3C PID as a fixed hardware address for neighbour table entries.
The driver matches I3C devices that have the MIPI assigned DCR 0xCC for
MCTP.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
RFC1662 defines the start state for the crc16 FCS to be 0xffff, but
we're currently starting at zero.
This change uses the correct start state. We're only early in the
adoption for the serial binding, so there aren't yet any other users to
interface to.
Fixes: a0c2ccd9b5 ("mctp: Add MCTP-over-serial transport binding")
Reported-by: Harsh Tyagi <harshtya@google.com>
Tested-by: Harsh Tyagi <harshtya@google.com>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're currently hitting the WARN_ON in mctp_i2c_flow_release:
if (midev->release_count > midev->i2c_lock_count) {
WARN_ONCE(1, "release count overflow");
This may be hit if we expire a flow before sending the first packet it
contains - as we will not be pairing the increment of release_count
(performed on flow release) with the i2c lock operation (only
performed on actual TX).
To fix this, only release a flow if we've encountered it previously (ie,
dev_flow_state does not indicate NEW), as we will mark the flow as
ACTIVE at the same time as accounting for the i2c lock operation. We
also need to add an INVALID flow state, to indicate when we've done the
release.
Fixes: f5b8abf9fc ("mctp i2c: MCTP I2C binding driver")
Reported-by: Jian Zhang <zhangjian.3032@bytedance.com>
Tested-by: Jian Zhang <zhangjian.3032@bytedance.com>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20221110053135.329071-1-jk@codeconstruct.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
header_ops.create should return the length of the header,
instead mctp_i2c_head_create() returned 0.
This didn't cause any problem because the MCTP stack accepted
0 as success.
Fixes: f5b8abf9fc ("mctp i2c: MCTP I2C binding driver")
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit
baebdf48c3 ("net: dev: Makes sure netif_rx() can be invoked in any context.")
the function netif_rx() can be used in preemptible/thread context as
well as in interrupt context.
Use netif_rx().
Cc: Jeremy Kerr <jk@codeconstruct.com.au>
Cc: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should be testing the length before fitting into the u8 byte_count.
This is just a sanity check, the MCTP stack should have limited to MTU
which is checked, and we check consistency later in mctp_i2c_xmit().
Found by Smatch
mctp_i2c_header_create() warn: impossible condition
'(hdr->byte_count > 255) => (0-255 > 255)'
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Provides MCTP network transport over an I2C bus, as specified in
DMTF DSP0237. All messages between nodes are sent as SMBus Block Writes.
Each I2C bus to be used for MCTP is flagged in devicetree by a
'mctp-controller' property on the bus node. Each flagged bus gets a
mctpi2cX net device created based on the bus number. A
'mctp-i2c-controller' I2C client needs to be added under the adapter. In
an I2C mux situation the mctp-i2c-controller node must be attached only
to the root I2C bus. The I2C client will handle incoming I2C slave block
write data for subordinate busses as well as its own bus.
In configurations without devicetree a driver instance can be attached
to a bus using the I2C slave new_device mechanism.
The MCTP core will hold/release the MCTP I2C device while responses
are pending (a 6 second timeout or once a socket is closed, response
received etc). While held the MCTP I2C driver will lock the I2C bus so
that the correct I2C mux remains selected while responses are received.
(Ideally we would just lock the mux to keep the current bus selected for
the response rather than a full I2C bus lock, but that isn't exposed in
the I2C mux API)
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Wolfram Sang <wsa@kernel.org> # I2C transport parts
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri assures me that a ldisc->open with tty->disc_data set should never
happen, so this check doesn't do anything.
Reported-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current serial driver requires a maximum MTU of 68, and it doesn't
make sense to set a MTU below the MCTP-required baseline (of 68) either.
This change sets the min_mtu & max_mtu of the mctp netdev, essentially
disallowing changes. By using these instead of a ndo_change_mtu op, we
get the netlink extacks reported too.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We want to ensure that the tx work has finished before returning from
the ldisc close op, so do a synchronous cancel.
Reported-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This change adds a MCTP Serial transport binding, as defined by DMTF
specificiation DSP0253 - "MCTP Serial Transport Binding". This is
implemented as a new serial line discipline, and can be attached to
arbitrary tty devices.
From the Kconfig description:
This driver provides an MCTP-over-serial interface, through a
serial line-discipline, as defined by DMTF specification "DSP0253 -
MCTP Serial Transport Binding". By attaching the ldisc to a serial
device, we get a new net device to transport MCTP packets.
This allows communication with external MCTP endpoints which use
serial as their transport. It can also be used as an easy way to
provide MCTP connectivity between virtual machines, by forwarding
data between simple virtual serial devices.
Say y here if you need to connect to MCTP endpoints over serial. To
compile as a module, use m; the module will be called mctp-serial.
Once the N_MCTP line discipline is set [using ioctl(TCIOSETD)], we get a
new netdev suitable for MCTP communication.
The 'mctp' utility[1] provides a simple wrapper for this ioctl, using
'link serial <device>':
# mctp link serial /dev/ttyS0 &
# mctp link
dev lo index 1 address 0x00:00:00:00:00:00 net 1 mtu 65536 up
dev mctpserial0 index 5 address 0x(no-addr) net 1 mtu 68 down
[1]: https://github.com/CodeConstruct/mctp
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 71812af723, reversing
changes made to cc0be1ad68.
Wolfram Sang says:
Please revert. Besides the driver in net, it modifies the I2C core
code. This has not been acked by the I2C maintainer (in this case me).
So, please don't pull this in via the net tree. The question raised here
(extending SMBus calls to 255 byte) is complicated because we need ABI
backwards compatibility.
Link: https://lore.kernel.org/all/YZJ9H4eM%2FM7OXVN0@shikoro/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Provides MCTP network transport over an I2C bus, as specified in
DMTF DSP0237. All messages between nodes are sent as SMBus Block Writes.
Each I2C bus to be used for MCTP is flagged in devicetree by a
'mctp-controller' property on the bus node. Each flagged bus gets a
mctpi2cX net device created based on the bus number. A
'mctp-i2c-controller' I2C client needs to be added under the adapter. In
an I2C mux situation the mctp-i2c-controller node must be attached only
to the root I2C bus. The I2C client will handle incoming I2C slave block
write data for subordinate busses as well as its own bus.
In configurations without devicetree a driver instance can be attached
to a bus using the I2C slave new_device mechanism.
The MCTP core will hold/release the MCTP I2C device while responses
are pending (a 6 second timeout or once a socket is closed, response
received etc). While held the MCTP I2C driver will lock the I2C bus so
that the correct I2C mux remains selected while responses are received.
(Ideally we would just lock the mux to keep the current bus selected for
the response rather than a full I2C bus lock, but that isn't exposed in
the I2C mux API)
This driver requires I2C adapters that allow 255 byte transfers
(SMBus 3.0) as the specification requires a minimum MTU of 68 bytes.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
