The check condition should be 'i < bc->onecell_data.num_domains', not
'bc->onecell_data.num_domains' which will make the look never finish
and cause kernel panic.
Also disable runtime to address
"imx93-blk-ctrl 4ac10000.system-controller: Unbalanced pm_runtime_enable!"
Fixes: e9aa77d413 ("soc: imx: add i.MX93 media blk ctrl driver")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefan Wahren <wahrenst@gmx.net>
Cc: stable@vger.kernel.org
Message-ID: <20241101101252.1448466-1-peng.fan@oss.nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 9094e53ff5 ("pmdomain: core: Use dev_name() instead of
kobject_get_path() in debugfs") severely shortened the names of devices
in a PM Domain. Now the most common format[1] consists of a 32-bit
unit-address (8 characters), followed by a dot and a node name (20
characters for "air-pollution-sensor" and "interrupt-controller", which
are the longest generic node names documented in the Devicetree
Specification), for a typical maximum of 29 characters.
This offers a good opportunity to reduce the table width of the debug
summary:
- Reduce the device name field width from 50 to 30 characters, which
matches the PM Domain name width,
- Reduce the large inter-column space between the "performance" and
"managed by" columns.
Visual impact:
- The "performance" column now starts at a position that is a
multiple of 16, just like the "status" and "children" columns,
- All of the "/device", "runtime status", and "managed by" columns are
now indented 4 characters more than the columns right above them,
- Everything fits in (one less than) 80 characters again ;-)
[1] Note that some device names (e.g. TI AM335x interconnect target
modules) do not follow this convention, and may be much longer, but
these didn't fit in the old 50-character column width either.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/f8e1821364b6d5d11350447c128f6d2b470f33fe.1725459707.git.geert+renesas@glider.be
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The removed code was added to handle the case where the power domain is
already on during the driver's probing. In this use case, the "is_off"
parameter is passed as false to pm_genpd_init() to inform it not to call
the power_on() callback, as it's unnecessary to perform the hardware
power-on procedure since the power domain is already on. Therefore, with
the call to clk_bulk_prepare_enable() by probe(), the system is in the
same operational state as when "is_off" is passed as true after the
power_on() callback execution:
probe() -> is_off == true -> clk_bulk_prepare_enable() called by power_on()
probe() -> is_off == false -> clk_bulk_prepare_enable() called by probe()
Reaching the same logical and operational state, it follows that upon
driver removal, there is no need to perform different actions depending
on the power domain's on/off state during probing.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/r/20240825143428.556439-2-dario.binacchi@amarulasolutions.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
for_each_available_child_of_node() can help to iterate through the
device_node, and we don't need to use while loop. Besides, the purpose
of the while loop is to find a device_node which fits the condition
"child_req_np == ref_np", we can just read the property of "child_np"
directly in for_each_available_child_of_node(). No functional change
with such conversion.
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Link: https://lore.kernel.org/r/20240821034022.27394-2-zhangzekun11@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the pmdomain fixes for v6.11-rc[n] into the next branch, to allow them
to get tested together with the new changes that are targeted for v6.12.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With "quiet" set in bootargs, there is power domain failure:
"imx93_power_domain 44462400.power-domain: pd_off timeout: name:
44462400.power-domain, stat: 4"
The current power on opertation takes ISO state as power on finished
flag, but it is wrong. Before powering on operation really finishes,
powering off comes and powering off will never finish because the last
powering on still not finishes, so the following powering off actually
not trigger hardware state machine to run. SSAR is the last step when
powering on a domain, so need to wait SSAR done when powering on.
Since EdgeLock Enclave(ELE) handshake is involved in the flow, enlarge
the waiting time to 10ms for both on and off to avoid timeout.
Cc: stable@vger.kernel.org
Fixes: 0a0f7cc25d ("soc: imx: add i.MX93 SRC power domain driver")
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20240814124740.2778952-1-peng.fan@oss.nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Raspberry Pi power driver heavily relies on the logging of the
underlying firmware driver. This results in disadvantages like unspecific
error messages or limited debugging options. So implement the logging for
the most important function rpi_firmware_set_power.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20240728114200.75559-5-wahrenst@gmx.net
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the pmdomain fixes for v6.11-rc[n] into the next branch, to allow them
to get tested together with the new changes that are targeted for v6.12.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Using kobject_get_path() means a dynamic memory allocation gets done, which
doesn't work on a PREEMPT_RT based configuration while holding genpd's raw
spinlock.
To fix the problem, let's convert into using the simpler dev_name(). This
means the information about the path doesn't get presented in debugfs, but
hopefully this shouldn't be an issue.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Raghavendra Kakarla <quic_rkakarla@quicinc.com> # qcm6490 with PREEMPT_RT set
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20240527142557.321610-4-ulf.hansson@linaro.org
There is no need to hold the genpd-lock, while assigning the
dev->pm_domain. In fact, it becomes a problem on a PREEMPT_RT based
configuration as the genpd-lock may be a raw spinlock, while the lock
acquired through the call to dev_pm_domain_set() is a regular spinlock.
To fix the problem, let's simply move the calls to dev_pm_domain_set()
outside the genpd-lock.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Raghavendra Kakarla <quic_rkakarla@quicinc.com> # qcm6490 with PREEMPT_RT set
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20240527142557.321610-3-ulf.hansson@linaro.org
To allow a genpd provider for a CPU PM domain to enter a domain-idle-state
during s2idle on a PREEMPT_RT based configuration, we can't use the regular
spinlock, as they are turned into sleepable locks on PREEMPT_RT.
To address this problem, let's convert into using the raw spinlock, but
only for genpd providers that have the GENPD_FLAG_CPU_DOMAIN bit set. In
this way, the lock can still be acquired/released in atomic context, which
is needed in the idle-path for PREEMPT_RT.
Do note that the genpd power-on/off notifiers may also be fired during
s2idle, but these are already prepared for PREEMPT_RT as they are based on
the raw notifiers. However, consumers of them may need to adopt accordingly
to work properly on PREEMPT_RT.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Raghavendra Kakarla <quic_rkakarla@quicinc.com> # qcm6490 with PREEMPT_RT set
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20240527142557.321610-2-ulf.hansson@linaro.org
Merge the pmdomain fixes for v6.10-rc[n] into the next branch, to allow them
to get tested together with the new changes that are targeted for v6.11.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some power-domains may be capable of relying on the HW to control the power
for a device that's hooked up to it. Typically, for these kinds of
configurations the consumer driver should be able to change the behavior of
power domain at runtime, control the power domain in SW mode for certain
configurations and handover the control to HW mode for other usecases.
To allow a consumer driver to change the behaviour of the PM domain for its
device, let's provide a new function, dev_pm_genpd_set_hwmode(). Moreover,
let's add a corresponding optional genpd callback, ->set_hwmode_dev(),
which the genpd provider should implement if it can support switching
between HW controlled mode and SW controlled mode. Similarly, add the
dev_pm_genpd_get_hwmode() to allow consumers to read the current mode and
its corresponding optional genpd callback, ->get_hwmode_dev(), which the
genpd provider can also implement to synchronize the initial HW mode
state in genpd_add_device() by reading back the mode from the hardware.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Jagadeesh Kona <quic_jkona@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Taniya Das <quic_tdas@quicinc.com>
Link: https://lore.kernel.org/r/20240624044809.17751-2-quic_jkona@quicinc.com
In the cases where the power domain connected to logics is allowed to
transition from a level(L)-->power collapse(0)-->retention(1) or
vice versa retention(1)-->power collapse(0)-->level(L) will cause the
logic to lose the configurations. The ARC does not support retention
to collapse transition on MxC rails.
The targets from SM8450 onwards the PLL logics of clock controllers are
connected to MxC rails and the recommended configurations are carried
out during the clock controller probes. The MxC transition as mentioned
above should be skipped to ensure the PLL settings are intact across
clock controller power on & off.
On older targets that do not split MX into MxA and MxC does not collapse
the logic and it is parked always at RETENTION, thus this issue is never
observed on those targets.
Cc: stable@vger.kernel.org # v5.17
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Link: https://lore.kernel.org/r/20240625-avoid_mxc_retention-v2-1-af9c2f549a5f@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On x86, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/pmdomain/amlogic/meson-gx-pwrc-vpu.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/pmdomain/amlogic/meson-ee-pwrc.o
Add the missing invocation of the MODULE_DESCRIPTION() macro to all
files which have a MODULE_LICENSE().
This includes meson-secure-pwrc.c which, although it did not produce a
warning with the x86 allmodconfig configuration, may cause this
warning with other configurations where CONFIG_MESON_SM is enabled.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240610-md-drivers-pmdomain-amlogic-v1-1-b49ddb1a8bdf@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull pmdomain fix from Ulf Hansson:
- Fix regression in gpcv2 PM domain for i.MX8
* tag 'pmdomain-v6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm:
pmdomain: imx: gpcv2: Add delay after power up handshake
