ASoC: Fixes for v6.12
Some last updates for v6.12, one quirk plus a couple of fixes. One is a
minor fix for a relatively obscure driver and the other is a relatively
important fix for boot hangs with some audio graph based cards.
If user no update BIOS, the speaker will no sound.
This patch support old BIOS to have sound from speaker.
Fixes: 1e707769df ("ALSA: hda/realtek - Set GPIO3 to default at S4 state for Thinkpad with ALC1318")
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The audio graph card doesn't mark its subnodes such as multi {}, dpcm {}
and c2c {} as not requiring any suppliers. This causes a hang as Linux
waits for these phantom suppliers to show up on boot.
Make it clear these nodes have no suppliers.
Example error message:
[ 15.208558] platform 2034000.i2s: deferred probe pending: platform: wait for supplier /sound/multi
[ 15.208584] platform sound: deferred probe pending: asoc-audio-graph-card2: parse error
Signed-off-by: John Watts <contact@jookia.org>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://patch.msgid.link/20241108-graph_dt_fix-v1-1-173e2f9603d6@jookia.org
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC: Fixes for v6.12
A moderately large pile of small changes here, split fairly evenly
between fixes and ID additions/quirks and all of it driver specific.
Xiaomi Book Pro 14 2022 (MIA2210-AD) requires a quirk entry for its
internal microphone to be enabled.
This is likely due to similar reasons as seen previously on Redmi Book
14/15 Pro 2022 models (since they likely came with similar firmware):
- commit dcff8b7ca9 ("ASoC: amd: yc: Add Xiaomi Redmi Book Pro 15 2022
into DMI table")
- commit c1dd6bf619 ("ASoC: amd: yc: Add Xiaomi Redmi Book Pro 14 2022
into DMI table")
A quirk would likely be needed for Xiaomi Book Pro 15 2022 models, too.
However, I do not have such device on hand so I will leave it for now.
Signed-off-by: Mingcong Bai <jeffbai@aosc.io>
Link: https://patch.msgid.link/20241106024052.15748-1-jeffbai@aosc.io
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of error when requesting ctrl_chan DMA channel, ctrl_chan is not
null. So the release of the dma channel leads to the following issue:
[ 4.879000] st,stm32-spdifrx 500d0000.audio-controller:
dma_request_slave_channel error -19
[ 4.888975] Unable to handle kernel NULL pointer dereference
at virtual address 000000000000003d
[...]
[ 5.096577] Call trace:
[ 5.099099] dma_release_channel+0x24/0x100
[ 5.103235] stm32_spdifrx_remove+0x24/0x60 [snd_soc_stm32_spdifrx]
[ 5.109494] stm32_spdifrx_probe+0x320/0x4c4 [snd_soc_stm32_spdifrx]
To avoid this issue, release channel only if the pointer is valid.
Fixes: 794df9448e ("ASoC: stm32: spdifrx: manage rebind issue")
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Link: https://patch.msgid.link/20241105140242.527279-1-olivier.moysan@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If amdtp_stream_init() fails in amdtp_tscm_init(), the latter returns zero,
though it's supposed to return error code, which is checked inside
init_stream() in file tascam-stream.c.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 47faeea25e ("ALSA: firewire-tascam: add data block processing layer")
Signed-off-by: Murad Masimov <m.masimov@maxima.ru>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20241101185517.1819-1-m.masimov@maxima.ru
The legacy rawmidi tries to enumerate all possible UMP groups
belonging to the UMP endpoint. But currently it shows all 16 ports
when the UMP endpoint is configured with static blocks, although most
of them may be unused.
There was already a fix for the sequencer client side to ignore such
groups in the commit 3bfd7c0ba1 ("ALSA: seq: ump: Skip useless ports
for static blocks"), and this commit is a similar fix for UMP
rawmidi devices; it adds simply the check for the validity of each
group that has been already parsed. (Note that the group info was
moved to snd_ump_endpoint.groups[] by the commit 0642a3c5ca
("ALSA: ump: Update substream name from assigned FB names")).
Link: https://patch.msgid.link/20241104100735.16127-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 4f61c8fe35 ("ALSA: hda/conexant: Mute speakers at suspend /
shutdown") mutes speakers on system shutdown or whenever HDA controller
is suspended by PM; this however interacts badly with Thinkpad's ACPI
firmware behavior which uses beeps to signal various events (enter/leave
suspend or hibernation, AC power connect/disconnect, low battery, etc.);
now those beeps are either muted altogether (for suspend/hibernate/
shutdown related events) or work more or less randomly (eg. AC
plug/unplug is only audible when you are playing music at the moment,
because HDA device is likely in suspend mode otherwise).
Since the original bug report mentioned in 4f61c8fe35 complained about
Lenovo's Thinkpad laptop - revert this commit altogether.
Fixes: 4f61c8fe35 ("ALSA: hda/conexant: Mute speakers at suspend / shutdown")
Signed-off-by: Jarosław Janik <jaroslaw.janik@gmail.com>
Link: https://patch.msgid.link/20241030171813.18941-2-jaroslaw.janik@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The WD19 family of docks has the same audio chipset as the WD15. This
change enables jack detection on the WD19.
We don't need the dell_dock_mixer_init quirk for the WD19. It is only
needed because of the dell_alc4020_map quirk for the WD15 in
mixer_maps.c, which disables the volume controls. Even for the WD15,
this quirk was apparently only needed when the dock firmware was not
updated.
Signed-off-by: Jan Schär <jan@jschaer.ch>
Cc: <stable@vger.kernel.org>
Link: https://patch.msgid.link/20241029221249.15661-1-jan@jschaer.ch
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASoC: Fixes for v6.12
The biggest set of changes here is Hans' fixes and quirks for various
Baytrail based platforms with RT5640 CODECs, and there's one core fix
for a missed length assignment for __counted_by() checking. Otherwise
it's small device specific fixes, several of them in the DT bindings.
On a system with wcd937x, rxmacro and Qualcomm audio DSP, which is pretty
common set of devices on Qualcomm platforms, and due to the order of how
DAPM widgets are powered on (they are sorted), there is a small time window
when wcd937x chip is online and expects the flow of incoming data but
rxmacro is not yet online. When wcd937x is programmed to receive data
via AUX port then its AUX PDM watchdog is enabled in
wcd937x_codec_enable_aux_pa(). If due to some reasons the rxmacro and
soundwire machinery are delayed to start streaming data, then there is
a chance for this AUX PDM watchdog to reset the wcd937x codec. Such event
is not logged as a message and only wcd937x IRQ counter is increased
however there could be a lot of other reasons for that IRQ.
There is a similar opportunity for such delay during DAPM widgets power
down sequence.
If wcd937x codec reset happens on the start of the playback, then there
will be no sound and if such reset happens at the end of a playback then
it may generate additional clicks and pops noises.
On qrb4210 RB2 board without any debugging bits the wcd937x resets are
sometimes observed at the end of a playback though not always.
With some debugging messages or with some tracing enabled the AUX PDM
watchdog resets the wcd937x codec at the start of a playback and there
is no sound output at all.
In this patch:
- TIMEOUT_SEL bit in PDM_WD_CTL2 register is set to increase the watchdog
reset delay to 100ms which eliminates the AUX PDM watchdog IRQs on
qrb4210 RB2 board completely and decreases the number of unwanted clicks
noises;
- HOLD_OFF bit postpones triggering such watchdog IRQ till wcd937x codec
reset which usually happens at the end of a playback. This allows to
actually output some sound in case of debugging.
Cc: Adam Skladowski <a39.skl@gmail.com>
Cc: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Cc: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Link: https://patch.msgid.link/20241022033132.787416-3-alexey.klimov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The widgets array in the snd_soc_dapm_widget_list has a __counted_by
attribute attached to it, which points to the num_widgets variable. This
attribute is used in bounds checking, and if it is not set before the
array is filled, then the bounds sanitizer will issue a warning or a
kernel panic if CONFIG_UBSAN_TRAP is set.
This patch sets the size of the widgets list calculated with
list_for_each as the initial value for num_widgets as it is used for
allocating memory for the array. It is updated with the actual number of
added elements after the array is filled.
Signed-off-by: Aleksei Vetrov <vvvvvv@google.com>
Fixes: 80e698e2df ("ASoC: soc-dapm: Annotate struct snd_soc_dapm_widget_list with __counted_by")
Link: https://patch.msgid.link/20241028-soc-dapm-bounds-checker-fix-v1-1-262b0394e89e@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some old Bay Trail tablets which shipped with Android as factory OS
have the SST/LPE audio engine described by an ACPI device with a
HID (Hardware-ID) of LPE0F28 instead of 80860F28.
Add support for this. Note this uses a new sst_res_info for just
the LPE0F28 case because it has a different layout for the IO-mem ACPI
resources then the 80860F28.
An example of a tablet which needs this is the Vexia EDU ATLA 10 tablet,
which has been distributed to schools in the Spanish Andalucía region.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patch.msgid.link/20241025090221.52198-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Vexia Edu Atla 10 tablet mostly uses the BYTCR tablet defaults,
but as happens on more models it is using IN1 instead of IN3 for
its internal mic and JD_SRC_JD2_IN4N instead of JD_SRC_JD1_IN4P
for jack-detection.
Add a DMI quirk for this to fix the internal-mic and jack-detection.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patch.msgid.link/20241024211615.79518-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On some x86 Bay Trail tablets which shipped with Android as factory OS,
the DSDT is so broken that the codec needs to be manually instantatiated
by the special x86-android-tablets.ko "fixup" driver for cases like this.
This means that the codec-dev cannot be retrieved through its ACPI fwnode,
add support to the bytcr_rt5640 machine driver for such manually
instantiated rt5640 i2c_clients.
An example of a tablet which needs this is the Vexia EDU ATLA 10 tablet,
which has been distributed to schools in the Spanish Andalucía region.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patch.msgid.link/20241024211615.79518-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC: Fixes for v6.12
An uncomfortably large set of fixes due to me not getting round to
sending them for longer than I should due to travel and illness. This
is mostly smaller driver specific changes, but there are a couple of
generic changes:
- Bumping the minimal topology ABI we check for during validation, the
code had support for v4 removed previously but the update of the
define used for initial validation was missed.
- Fix the assumption that DAPM structs will be embedded in a component
which isn't true for card widgets when doing name comparisons, though
fortunately this is rarely triggered.
We've pulled in one Soundwire fix which was part of a larger series
fixing cleanup issues in on Intel Soundwire systems.
On some platforms, for example i.MX93, there is only one
audio PLL source, so some sample rate can't be supported.
If the PLL source is used for 8kHz series rates, then 11kHz
series rates can't be supported.
So add constraints according to the frequency of available
clock sources, then alsa-lib will help to convert the
unsupported rate for the driver.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://patch.msgid.link/1728884313-6778-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the kconfig option for the tas2781 HDA driver to select CRC32 rather
than CRC32_SARWATE. CRC32_SARWATE is an option from the kconfig
'choice' that selects the specific CRC32 implementation. Selecting a
'choice' option seems to have no effect, but even if it did work, it
would be incorrect for a random driver to override the user's choice.
CRC32 is the correct option to select for crc32() to be available.
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://patch.msgid.link/20241020175624.7095-1-ebiggers@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The step variable is initialized to zero. It is changed in the loop,
but if it's not changed it will remain zero. Add a variable check
before the division.
The observed behavior was introduced by commit 826b5de90c
("ALSA: firewire-lib: fix insufficient PCM rule for period/buffer size"),
and it is difficult to show that any of the interval parameters will
satisfy the snd_interval_test() condition with data from the
amdtp_rate_table[] table.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 826b5de90c ("ALSA: firewire-lib: fix insufficient PCM rule for period/buffer size")
Signed-off-by: Andrey Shumilin <shum.sdl@nppct.ru>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://patch.msgid.link/20241018060018.1189537-1-shum.sdl@nppct.ru
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge series from Bard Liao <yung-chuan.liao@linux.intel.com>:
Clean up the link DMA for playback during stop for IPC4 is required to
reset the DMA read/write pointers when the stream is prepared and
restarted after a call to snd_pcm_drain()/snd_pcm_drop().
The change is mainly on ASoC. We may go via ASoC tree with Vinod's
Acked-by tag
Ranjani Sridharan (4):
ASoC: SOF: ipc4-topology: Do not set ALH node_id for aggregated DAIs
ASoC: SOF: Intel: hda: Handle prepare without close for non-HDA DAI's
soundwire: intel_ace2x: Send PDI stream number during prepare
ASoC: SOF: Intel: hda: Always clean up link DMA during stop
drivers/soundwire/intel_ace2x.c | 19 +++++-----------
sound/soc/sof/intel/hda-dai-ops.c | 23 +++++++++----------
sound/soc/sof/intel/hda-dai.c | 37 +++++++++++++++++++++++++++----
sound/soc/sof/ipc4-topology.c | 15 +++++++++++--
4 files changed, 62 insertions(+), 32 deletions(-)
--
2.43.0
On i.MX8MM the register of volume control has positive and negative
values. It is different from other platforms like i.MX8MP and i.MX93
which only have positive values. Add a volume_sx flag to use SX_TLV
volume control for this kind of platform. Use common TLV volume control
for other platforms.
Fixes: cdfa92eb90 ("ASoC: fsl_micfil: Correct the number of steps on SX controls")
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://patch.msgid.link/20241017071507.2577786-1-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Turns out some registers of pre-2.5 version of rxmacro codecs are not
located at the expected offsets but 0xc further away in memory. So far
the detected registers are CDC_RX_RX2_RX_PATH_SEC7 and
CDC_RX_RX2_RX_PATH_DSM_CTL.
CDC_RX_RXn_RX_PATH_DSM_CTL(rx, n) macro incorrectly generates the address
0x540 for RX2 but it should be 0x54C and it also overwrites
CDC_RX_RX2_RX_PATH_SEC7 which is located at 0x540.
The same goes for CDC_RX_RXn_RX_PATH_SEC7(rx, n).
Fix this by introducing additional rxn_reg_stride2 offset. For 2.5 version
and above this offset will be equal to 0.
With such change the corresponding RXn() macros will generate the same
values for 2.5 codec version for all RX paths and the same old values
for pre-2.5 version for RX0 and RX1. However for the latter case with
RX2 path it will also add rxn_reg_stride2 on top.
While at this, also remove specific if-check for INTERP_AUX from
rx_macro_digital_mute() and rx_macro_enable_interp_clk(). These if-check
was used to handle such special offset for AUX interpolator but since
CDC_RX_RXn_RX_PATH_SEC7(rx, n) and CDC_RX_RXn_RX_PATH_DSM_CTL(rx, n)
macros will generate the correst addresses of dsm register, they are no
longer needed.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patch.msgid.link/20241016221049.1145101-1-alexey.klimov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
