This patch adds device tree support for mfd driver and adds
Documentation/devicetree/bindings/mfd/max77686.txt.
This patch also intialize max77686 pointer to NULL in max77686_i2c_probe
to silent a compile time warning.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
gpio-i2c describes an I2C controller (using gpios for data and clock),
so it must be described in i2c, not gpio.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Change the value of #interrupt-cells of gpio nodes from 1 to 2, so that
the gpio irq type can be specified in device tree. Also update binding
document to make it clear.
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
There is multiple voltage input pins on device which
takes the voltage input for different voltage regulator.
Support to configure the voltage input supplied by
different regulator for each regulators.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds a driver for the MLC NAND controller of the LPC32xx SoC.
[dwmw2: 21st century pedantry]
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The of_get_named_gpio_flags can retrieve the second cell of
gpio-specifier as the "flags". The imx and mxs gpio driver do not
have their own .xlate callback, which means of_gpio_simple_xlate is
used and it's a 1:1 mapping between gpio controller flags and Linux
"enum of_gpio_flags".
Update imx and mxs bindings document to make it clear.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add support for input supply in DT parsing of node.
The input supply will be provided by the property
"vin-supply" in the regulator node.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add the policy for regulator DT such that if device have multiple
regulator and its binding contains a child node that describes each
regulator then each regulator child node must have the property
"regulator-compatible" which matches with regulator name of their
hardware counterparts.
Modify the DT documentation of regulator devices to reflect this
policy.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
mx23-olinuxino is a low cost board designed by Olimex.
It has the following features:
- Freescale iMX233 ARM926J processor at 454MHz
-64 MB RAM
-SD-card connector
-TV PAL/NTSC video output
-2 USB High Speed Hosts
-Ethernet 100 Mbit
-Stereo Audio Input
-Stereo Headphones Audio Output
More information at:
http://www.olimex.com/dev/imx233-olinuxino-maxi.html
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add AM335X BeagleBone device tree source (am335x-evm.dts) file
to use the am33xx.dtsi SoC file, along with the memory node
information.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Reviewed-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a simple device tree probe support for mxsfb driver. Before
a common binding for struct fb_videomode is available, the driver will
keep using struct mxsfb_platform_data. That said, platform code will
use auxdata to attach mxsfb_platform_data for device tree boot.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add auxdata to instantiate the PWFM controller from a device tree,
include the corresponding nodes in the dtsi files for Tegra 20 and
Tegra 30 and add binding documentation.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
The property clock-frequency is optional for device tree probe. When
it's absent, the flexcan driver will try to get the frequency from clk
system by calling clk_get_rate.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add a driver for BCM8706 and BCM8727 devices. These are a 10Gig PHYs
which use MII_ADDR_C45 addressing. They are always 10G full duplex, so
there is no autonegotiation. All we do is report link state and send
interrupts when it changes.
If the PHY has a device tree of_node associated with it, the
"broadcom,c45-reg-init" property is used to supply register
initialization values when config_init() is called.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define two new "compatible" values for Ethernet
PHYs. "ethernet-phy-ieee802.3-c22" and "ethernet-phy-ieee802.3-c45"
are used to indicate a PHY uses the corresponding protocol.
If a PHY is "compatible" with "ethernet-phy-ieee802.3-c45", we
indicate this so that get_phy_device() can properly probe the device.
If get_phy_device() fails, it was probably due to failing the probe of
the PHY identifier registers. Since we have the device tree telling
us the PHY exists, go ahead and add it anyhow with a phy_id of zero.
There may be a driver match based on the "compatible" property.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different boards may require different phy reset duration. Add property
phy-reset-duration for device tree probe, so that the boards that need
a longer reset duration can specify it in their device tree.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy-reset-gpios is an optional property for fec device tree boot.
Change the binding document to match the driver code.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for memory controller on Calxeda Highbank platforms. Highbank
platforms support a single 4GB mini-DIMM with 1-bit correction and 2-bit
detection.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The necessary info is expected to pass from DT.
For more precise resource reservation, there shouldn't be any
overlapping of register range between SMMU and MC. SMMU register
offset needs to be calculated correctly, based on its register bank.
Signed-off-by: Hiroshi DOYU <hdoyu@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Due to the lack of a generic clock API we'd had the 32kHz clock in the
regulator driver but this is definitely a Linux-specific thing and now
we have a clock API hopefully the code can be moved elsewhere. Try to
avoid getting DTs deployed relying on the 32kHz clock by removing it
from the bindings, grep seems to tell me it's not currently used anyway.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For some hardwares ramp_delay for BUCKs is a configurable parameter which can
be configured through DT or board file.This patch adds ramp_delay to regulator
constraints and allow user to configure it for regulators which supports this
feature, through DT or board file. It will provide two ways of setting the
ramp_delay for a regulator:
First, by setting it as constraints in board file(for configurable
regulators) and set_machine_constraints() will take care of setting it on
hardware by calling(the provided) .set_ramp_delay() operation(callback).
Second, by setting it as data in regulator_desc(as fixed/default
ramp_delay rate) for a regulator in driver.
regulator_set_voltage_time_sel() will give preference to
constraints->ramp_delay while reading ramp_delay rate for regulator. Similarly
users should also take care accordingly while refering ramp_delay rate(in case
of implementing their private .set_voltage_time_sel() callbacks for different
regulators).
[Rewrote subject for 80 columns -- broonie]
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds helpers to support device tree bindings for the generic
PWM API. Device tree binding documentation for PWM controllers is also
provided.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
The gpio numbers does not match the comment.
Fix the comments for GPIOs used for chip selects.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
