commit 02d210f434 upstream.
Commit 130a96d698 ("usb: typec: ucsi: acpi: Increase command
completion timeout value") increased the timeout from 5 seconds
to 60 seconds due to issues related to alternate mode discovery.
After the alternate mode discovery switch to polled mode
the timeout was reduced, but instead of being set back to
5 seconds it was reduced to 1 second.
This is causing problems when using a Lenovo ThinkPad X1 yoga gen7
connected over Type-C to a LG 27UL850-W (charging DP over Type-C).
When the monitor is already connected at boot the following error
is logged: "PPM init failed (-110)", /sys/class/typec is empty and
on unplugging the NULL pointer deref fixed earlier in this series
happens.
When the monitor is connected after boot the following error
is logged instead: "GET_CONNECTOR_STATUS failed (-110)".
Setting the timeout back to 5 seconds fixes both cases.
Fixes: e08065069f ("usb: typec: ucsi: acpi: Reduce the command completion timeout")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230308154244.722337-4-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8a2bb4eb7 upstream.
Previously, there was a 100uS delay inserted after issuing an end transfer
command for specific controller revisions. This was due to the fact that
there was a GUCTL2 bit field which enabled synchronous completion of the
end transfer command once the CMDACT bit was cleared in the DEPCMD
register. Since this bit does not exist for all controller revisions and
the current implementation heavily relies on utizling the EndTransfer
command completion interrupt, add the delay back in for uses where the
interrupt on completion bit is not set, and increase the duration to 1ms
for the controller to complete the command.
An issue was seen where the USB request buffer was unmapped while the DWC3
controller was still accessing the TRB. However, it was confirmed that the
end transfer command was successfully submitted. (no end transfer timeout)
In situations, such as dwc3_gadget_soft_disconnect() and
__dwc3_gadget_ep_disable(), the dwc3_remove_request() is utilized, which
will issue the end transfer command, and follow up with
dwc3_gadget_giveback(). At least for the USB ep disable path, it is
required for any pending and started requests to be completed and returned
to the function driver in the same context of the disable call. Without
the GUCTL2 bit, it is not ensured that the end transfer is completed before
the buffers are unmapped.
Fixes: cf2f8b63f7 ("usb: dwc3: gadget: Remove END_TRANSFER delay")
Cc: stable <stable@kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230306200557.29387-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a826492fc9 upstream.
The kernel will dump in the below cases:
sysfs: cannot create duplicate filename
'/devices/virtual/usb_power_delivery/pd1/source-capabilities'
1. After soft reset has completed, an Explicit Contract negotiation occurs.
The sink device will receive source capabilitys again. This will cause
a duplicate source-capabilities file be created.
2. Power swap twice on a device that is initailly sink role.
This will unregister existing capabilities when above cases occurs.
Fixes: 8203d26905 ("usb: typec: tcpm: Register USB Power Delivery Capabilities")
cc: <stable@vger.kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230215054951.238394-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c67ed9ad9 upstream.
In the unbind callback for f_uac1 and f_uac2, a call to snd_card_free()
via g_audio_cleanup() will disconnect the card and then wait for all
resources to be released, which happens when the refcount falls to zero.
Since userspace can keep the refcount incremented by not closing the
relevant file descriptor, the call to unbind may block indefinitely.
This can cause a deadlock during reboot, as evidenced by the following
blocked task observed on my machine:
task:reboot state:D stack:0 pid:2827 ppid:569 flags:0x0000000c
Call trace:
__switch_to+0xc8/0x140
__schedule+0x2f0/0x7c0
schedule+0x60/0xd0
schedule_timeout+0x180/0x1d4
wait_for_completion+0x78/0x180
snd_card_free+0x90/0xa0
g_audio_cleanup+0x2c/0x64
afunc_unbind+0x28/0x60
...
kernel_restart+0x4c/0xac
__do_sys_reboot+0xcc/0x1ec
__arm64_sys_reboot+0x28/0x30
invoke_syscall+0x4c/0x110
...
The issue can also be observed by opening the card with arecord and
then stopping the process through the shell before unbinding:
# arecord -D hw:UAC2Gadget -f S32_LE -c 2 -r 48000 /dev/null
Recording WAVE '/dev/null' : Signed 32 bit Little Endian, Rate 48000 Hz, Stereo
^Z[1]+ Stopped arecord -D hw:UAC2Gadget -f S32_LE -c 2 -r 48000 /dev/null
# echo gadget.0 > /sys/bus/gadget/drivers/configfs-gadget/unbind
(observe that the unbind command never finishes)
Fix the problem by using snd_card_free_when_closed() instead, which will
still disconnect the card as desired, but defer the task of freeing the
resources to the core once userspace closes its file descriptor.
Fixes: 132fcb4608 ("usb: gadget: Add Audio Class 2.0 Driver")
Cc: stable@vger.kernel.org
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Reviewed-by: John Keeping <john@metanate.com>
Link: https://lore.kernel.org/r/20230302163648.3349669-1-alvin@pqrs.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f747313249 upstream.
Each time the platform goes to low power, PM suspend / resume routines
call: __dwc2_lowlevel_hw_enable -> devm_add_action_or_reset().
This adds a new devres each time.
This may also happen at runtime, as dwc2_lowlevel_hw_enable() can be
called from udc_start().
This can be seen with tracing:
- echo 1 > /sys/kernel/debug/tracing/events/dev/devres_log/enable
- go to low power
- cat /sys/kernel/debug/tracing/trace
A new "ADD" entry is found upon each low power cycle:
... devres_log: 49000000.usb-otg ADD 82a13bba devm_action_release (8 bytes)
... devres_log: 49000000.usb-otg ADD 49889daf devm_action_release (8 bytes)
...
A second issue is addressed here:
- regulator_bulk_enable() is called upon each PM cycle (suspend/resume).
- regulator_bulk_disable() never gets called.
So the reference count for these regulators constantly increase, by one
upon each low power cycle, due to missing regulator_bulk_disable() call
in __dwc2_lowlevel_hw_disable().
The original fix that introduced the devm_add_action_or_reset() call,
fixed an issue during probe, that happens due to other errors in
dwc2_driver_probe() -> dwc2_core_reset(). Then the probe fails without
disabling regulators, when dr_mode == USB_DR_MODE_PERIPHERAL.
Rather fix the error path: disable all the low level hardware in the
error path, by using the "hsotg->ll_hw_enabled" flag. Checking dr_mode
has been introduced to avoid a dual call to dwc2_lowlevel_hw_disable().
"ll_hw_enabled" should achieve the same (and is used currently in the
remove() routine).
Fixes: 54c1960605 ("usb: dwc2: Always disable regulators on driver teardown")
Fixes: 33a06f1300 ("usb: dwc2: Fix error path in gadget registration")
Cc: stable <stable@kernel.org>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20230316084127.126084-1-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 82f5332d3b upstream.
Some boards might use USB-A female connector for USB ports, however,
the port could be connected to a dual-mode USB controller, making it
also behaves as a peripheral device if male-to-male cable is connected.
In this case, the dts looks like this:
&usb0 {
status = "okay";
dr_mode = "otg";
usb-role-switch;
role-switch-default-mode = "host";
};
After boot, dwc2_ovr_init() sets GOTGCTL to GOTGCTL_AVALOVAL and call
dwc2_force_mode() with parameter host=false, which causes inconsistent
mode - The hardware is in peripheral mode while the kernel status is
in host mode.
What we can do now is to call dwc2_drd_role_sw_set() to switch to
device mode, and everything should work just fine now, even switching
back to none(default) mode afterwards.
Fixes: e14acb8769 ("usb: dwc2: drd: add role-switch-default-node support")
Cc: stable <stable@kernel.org>
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Tested-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Reviewed-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/SG2PR01MB204837BF68EDB0E343D2A375C9A59@SG2PR01MB2048.apcprd01.prod.exchangelabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5021383242 upstream.
When in dual role mode (dr_mode == USB_DR_MODE_OTG), platform probe
successively basically calls:
- dwc2_gadget_init()
- dwc2_hcd_init()
- dwc2_lowlevel_hw_disable() since recent change [1]
- usb_add_gadget_udc()
The PHYs (and so the clocks it may provide) shouldn't be disabled for all
SoCs, in OTG mode, as the HCD part has been initialized.
On STM32 this creates some weird race condition upon boot, when:
- initially attached as a device, to a HOST
- and there is a gadget script invoked to setup the device part.
Below issue becomes systematic, as long as the gadget script isn't
started by userland: the hardware PHYs (and so the clocks provided by the
PHYs) remains disabled.
It ends up in having an endless interrupt storm, before the watchdog
resets the platform.
[ 16.924163] dwc2 49000000.usb-otg: EPs: 9, dedicated fifos, 952 entries in SPRAM
[ 16.962704] dwc2 49000000.usb-otg: DWC OTG Controller
[ 16.966488] dwc2 49000000.usb-otg: new USB bus registered, assigned bus number 2
[ 16.974051] dwc2 49000000.usb-otg: irq 77, io mem 0x49000000
[ 17.032170] hub 2-0:1.0: USB hub found
[ 17.042299] hub 2-0:1.0: 1 port detected
[ 17.175408] dwc2 49000000.usb-otg: Mode Mismatch Interrupt: currently in Host mode
[ 17.181741] dwc2 49000000.usb-otg: Mode Mismatch Interrupt: currently in Host mode
[ 17.189303] dwc2 49000000.usb-otg: Mode Mismatch Interrupt: currently in Host mode
...
The host part is also not functional, until the gadget part is configured.
The HW may only be disabled for peripheral mode (original init), e.g.
dr_mode == USB_DR_MODE_PERIPHERAL, until the gadget driver initializes.
But when in USB_DR_MODE_OTG, the HW should remain enabled, as the HCD part
is able to run, while the gadget part isn't necessarily configured.
I don't fully get the of purpose the original change, that claims disabling
the hardware is missing. It creates conditions on SOCs using the PHY
initialization to be completely non working in OTG mode. Original
change [1] should be reworked to be platform specific.
[1] https://lore.kernel.org/r/20221206-dwc2-gadget-dual-role-v1-2-36515e1092cd@theobroma-systems.com
Fixes: ade23d7b7e ("usb: dwc2: power on/off phy for peripheral mode in dual-role mode")
Cc: stable <stable@kernel.org>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Tested-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20230315144433.3095859-1-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ce33e64c17 ]
The allocation of PageBuffer is 512 bytes in size, but the dereferencing
of struct ms_bootblock_idi (also size 512) happens at a calculated offset
within the allocation, which means the object could potentially extend
beyond the end of the allocation. Avoid this case by just allocating
enough space to catch any accesses beyond the end. Seen with GCC 13:
../drivers/usb/storage/ene_ub6250.c: In function 'ms_lib_process_bootblock':
../drivers/usb/storage/ene_ub6250.c:1050:44: warning: array subscript 'struct ms_bootblock_idi[0]' is partly outside array bounds of 'unsigned char[512]' [-Warray-bounds=]
1050 | if (le16_to_cpu(idi->wIDIgeneralConfiguration) != MS_IDI_GENERAL_CONF)
| ^~
../include/uapi/linux/byteorder/little_endian.h:37:51: note: in definition of macro '__le16_to_cpu'
37 | #define __le16_to_cpu(x) ((__force __u16)(__le16)(x))
| ^
../drivers/usb/storage/ene_ub6250.c:1050:29: note: in expansion of macro 'le16_to_cpu'
1050 | if (le16_to_cpu(idi->wIDIgeneralConfiguration) != MS_IDI_GENERAL_CONF)
| ^~~~~~~~~~~
In file included from ../drivers/usb/storage/ene_ub6250.c:5:
In function 'kmalloc',
inlined from 'ms_lib_process_bootblock' at ../drivers/usb/storage/ene_ub6250.c:942:15:
../include/linux/slab.h:580:24: note: at offset [256, 512] into object of size 512 allocated by 'kmalloc_trace'
580 | return kmalloc_trace(
| ^~~~~~~~~~~~~~
581 | kmalloc_caches[kmalloc_type(flags)][index],
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
582 | flags, size);
| ~~~~~~~~~~~~
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230204183546.never.849-kees@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0fbd2cda92 ]
Walking the dram->cs array was seen as accesses beyond the first array
item by the compiler. Instead, use the array index directly. This allows
for run-time bounds checking under CONFIG_UBSAN_BOUNDS as well. Seen
with GCC 13 with -fstrict-flex-arrays:
In function 'xhci_mvebu_mbus_config',
inlined from 'xhci_mvebu_mbus_init_quirk' at ../drivers/usb/host/xhci-mvebu.c:66:2:
../drivers/usb/host/xhci-mvebu.c:37:28: warning: array subscript 0 is outside array bounds of 'const struct mbus_dram_window[0]' [-Warray-bounds=]
37 | writel(((cs->size - 1) & 0xffff0000) | (cs->mbus_attr << 8) |
| ~~^~~~~~
Cc: Mathias Nyman <mathias.nyman@intel.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230204183651.never.663-kees@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89e7252d6c ]
During enumeration or composition switch,a userspace process
agnostic of the conventions of configs can try to create function
symlinks even after the UDC is bound to current config which is
not correct. Potentially it can create duplicates within the
current config.
Prevent this by adding a check if udc_name already exists, then bail
out of cfg_link.
Following is an example:
Step1:
ln -s X1 ffs.a
-->cfg_link
--> usb_get_function(ffs.a)
->ffs_alloc
CFG->FUNC_LIST: <ffs.a>
C->FUNCTION: <empty>
Step2:
echo udc.name > /config/usb_gadget/g1/UDC
--> UDC_store
->composite_bind
->usb_add_function
CFG->FUNC_LIST: <empty>
C->FUNCTION: <ffs.a>
Step3:
ln -s Y1 ffs.a
-->cfg_link
-->usb_get_function(ffs.a)
->ffs_alloc
CFG->FUNC_LIST: <ffs.a>
C->FUNCTION: <ffs.a>
both the lists corresponds to the same function instance ffs.a
but the usb_function* pointer is different because in step 3
ffs_alloc has created a new reference to usb_function* for
ffs.a and added it to cfg_list.
Step4:
Now a composition switch involving <ffs.b,ffs.a> is executed.
the composition switch will involve 3 things:
1. unlinking the previous functions existing
2. creating new symlinks
3. writing UDC
However, the composition switch is generally taken care by
userspace process which creates the symlinks in its own
nomenclature(X*) and removes only those.
So it won't be able to remove Y1 which user had created
by own.
Due to this the new symlinks cannot be created for ffs.a
since the entry already exists in CFG->FUNC_LIST.
The state of the CFG->FUNC_LIST is as follows:
CFG->FUNC_LIST: <ffs.a>
Fixes: 88af8bbe4e ("usb: gadget: the start of the configfs interface")
Signed-off-by: Krishna Kurapati PSSNV <quic_kriskura@quicinc.com>
Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Link: https://lore.kernel.org/r/20230201132308.31523-1-quic_ugoswami@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8d3392e0e ]
When request_irq(ires1->start) failed in w5300_hw_probe(), irq
ires->start has not been freed, and on the clean_up3 error path,
we also need to free ires1->start irq, fix it.
In addition, We should add free_irq in fusb300_remove(), and give
the lables a proper name so that they can be understood easily,
so add free_irq in fusb300_remove(), and update clean_up3 to
err_alloc_request.
Fixes: 0fe6f1d1f6 ("usb: udc: add Faraday fusb300 driver")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Link: https://lore.kernel.org/r/20221123014121.1989721-1-cuigaosheng1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 45bf39f8df upstream.
Ever since commit 83e83ecb79 ("usb: core: get config and string
descriptors for unauthorized devices") was merged in 2013, there has
been no mechanism for reallocating the rawdescriptors buffers in
struct usb_device after the initial enumeration. Before that commit,
the buffers would be deallocated when a device was deauthorized and
reallocated when it was authorized and enumerated.
This means that the locking in the read_descriptors() routine is not
needed, since the buffers it reads will never be reallocated while the
routine is running. This locking can interfere with user programs
trying to read a hub's descriptors via sysfs while new child devices
of the hub are being initialized, since the hub is locked during this
procedure.
Since the locking in read_descriptors() hasn't been needed for over
nine years, we can remove it.
Reported-and-tested-by: Troels Liebe Bentsen <troels@connectedcars.dk>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: stable@vger.kernel.org
Link: https://lore.kernel.org/r/Y9l+wDTRbuZABzsE@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While checking Pin Assignments of the port and partner during probe, we
don't take into account whether the peripheral is a plug or receptacle.
This manifests itself in a mode entry failure on certain docks and
dongles with captive cables. For instance, the Startech.com Type-C to DP
dongle (Model #CDP2DP) advertises its DP VDO as 0x405. This would fail
the Pin Assignment compatibility check, despite it supporting
Pin Assignment C as a UFP.
Update the check to use the correct DP Pin Assign macros that
take the peripheral's receptacle bit into account.
Fixes: c1e5c2f0cb ("usb: typec: altmodes/displayport: correct pin assignment for UFP receptacles")
Cc: stable@vger.kernel.org
Reported-by: Diana Zigterman <dzigterman@chromium.org>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Link: https://lore.kernel.org/r/20230208205318.131385-1-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
