[ Upstream commit 8a55c08d3b ]
Remove code that tell the OS that link is going down when user
change flow control via ethtool. When link is up it isn't certain
that link goes down after 0x0605 aq command. If link doesn't go
down, OS thinks that link is down, but physical link is up. To
reset this state user have to take interface down and up.
If link goes down after 0x0605 command, FW send information
about that and after that driver tells the OS that the link goes
down. So this code in ethtool is unnecessary.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a946843ba ]
Use ice_pf_to_dev(pf) instead of &pf->pdev->dev
Use ice_pf_to_dev(vsi->back) instead of &vsi->back->pdev->dev
When a pointer to the pf instance is available, use ice_pf_to_dev
instead of ice_hw_to_dev
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fbf1e1f698 ]
Logging the firmware/NVM information during driver load is redundant since
that information is also available via ethtool. Move the functionality
found in ice_nvm_version_str() directly into ice_get_drvinfo() and remove
calling the former and logging that info during driver probe. This also
gets rid of a bug in ice_nvm_version_str() where it returns a pointer to
a buffer which is free'ed when that function exits.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 168983a8e1 ]
Currently we compare the value we are about to write to the Rx tail
register with the previous value of next_to_use. The problem with this
is we only write tail on 8 descriptor boundaries, but next_to_use is
updated whenever we clean Rx descriptors. Fix this by comparing the
value we are about to write to tail with the previously written tail
value. This will prevent duplicate Rx tail bumps.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53977ee474 ]
When switching between FW and SW LLDP mode, the
number of configured TLV apps in the driver's
DCB configuration is getting out of synch with
what lldpad thinks is configured. This is causing
a problem when shutting down lldpad. The cleanup
is trying to delete TLV apps that are not defined
in the kernel.
Since the driver is keeping an accurate account
of the apps defined, use the drivers number of
apps to determine if there is an app to delete.
If the number of apps is <= 1, then do not
attempt to delete.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f45ebe0d8 ]
In the case where the hardware gives us a null Rx descriptor, it is
theoretically possible that we could call one of our skb-construction
functions with no data pointer, which would cause a panic.
In real life, this will never happen - we only get null RX
descriptors as the final descriptor in a chain of otherwise-valid
descriptors. When this happens, the skb will be extant and we'll just
call ice_add_rx_frag(), which can deal with empty data buffers.
Unfortunately, Coverity does not have intimate knowledge of our
hardware, so we must add a check here.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Replace all the occurrences of FIELD_SIZEOF() with sizeof_field() except
at places where these are defined. Later patches will remove the unused
definition of FIELD_SIZEOF().
This patch is generated using following script:
EXCLUDE_FILES="include/linux/stddef.h|include/linux/kernel.h"
git grep -l -e "\bFIELD_SIZEOF\b" | while read file;
do
if [[ "$file" =~ $EXCLUDE_FILES ]]; then
continue
fi
sed -i -e 's/\bFIELD_SIZEOF\b/sizeof_field/g' $file;
done
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Link: https://lore.kernel.org/r/20190924105839.110713-3-pankaj.laxminarayan.bharadiya@intel.com
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David Miller <davem@davemloft.net> # for net
The code in ice_sched_cleanup_all checks whether the port info is NULL
prior to calling ice_sched_clear_port. However, ice_sched_clear_port
already checks whether port info is non-NULL.
More importantly, it also checks whether the port structure has been
initialized by checking its port_state field as well.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add code to query and set the number of channels on the primary VSI for a
PF. This is accessed from the 'ethtool -l' and 'ethtool -L' commands,
respectively. Though the ice driver supports asymmetric queues report an
IRQ vector that has both Rx and Tx queues attached and is counted as a
'combined' channel.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Co-developed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The virtchannel interface was repeating a lot of strings
and wasting storage space in the kernel. There was also
inconsistent messages for the same thing. Consolidate all
those messages and bit checks into a couple of helper functions.
Also, reduce stack space usage by simplifying getting the pointer
to the pf using a helper.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Co-developed-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In situations where we alloc and free memory within the same function do
not use the devm_* variants; use regular alloc and free functions. Remove
any unused vars if there are no usages after these changes.
Also, replace an allocate and copy with kmemdup() and remove an
unnecessary memset() to 0 after a kzalloc().
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently ice_clear_vsi_promisc() detects if the VLAN ID sent is not 0
and sets the recipe_id to ICE_SW_LKUP_PROMISC_VLAN in that case and
ICE_SW_LKUP_PROMISC if the VLAN_ID is 0. However this doesn't allow VLAN
0 promiscuous rules to be removed, but they can be added. Fix this by
checking if the promisc_mask contains ICE_PROMISC_VLAN_RX or
ICE_PROMISC_VLAN_TX. This change was made to match what is being done
for ice_set_vsi_promisc().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently there can be a case where a DCB map is applied and there are
more interrupt vectors (vsi->num_q_vectors) than Rx queues (vsi->num_rxq)
and Tx queues (vsi->num_txq). If we try to set coalesce settings in this
case it will report a false failure. Fix this by checking if vector index
is valid with respect to the number of Tx and Rx queues configured.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It is wrong to set PF disable state flag for all VFs when freeing VF
resources - Instead, we should set VF disable state flag for each VF with
its resources being returned to the device. Right now, all VF opcodes,
mailbox communication to clear its resources as well fails - since we
already indicate that PF is in disable state, with all VFs not active. In
addition, we don't need to notify VF that PF is intending to reset it, if
it is already in disabled state.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the case of an invalid virtchannel request the driver
would return uninitialized data to the VF from the PF stack
which is a bug. Fix by initializing the stack variable
earlier in the function before any return paths can be taken.
Fixes: 1071a8358a ("ice: Implement virtchnl commands for AVF support")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently when adding/deleting vlans in ice_vc_process_vlan_msg()
we are calling ice_vsi_manage_vlan_stripping() to enable/disable
when adding and deleting a VLAN respectively. This is wrong
because adding/deleting VLANs has nothing to do with configuring
VLAN stripping. VLAN stripping is configured through the
following VIRTCHNL operations:
VIRTCHNL_OP_ENABLE_VLAN_STRIPPING
VIRTCHNL_OP_DISABLE_VLAN_STRIPPING
Unfortunately we can't just remove this because then stripping
will never be configured on VF initialization. Fix this by
adding a new function that initializes (disables/enables) VLAN
stripping for the VF based on the device supported capabilities.
This allows us to remove the call to
ice_vsi_manage_vlan_stripping() in ice_vc_process_vlan_msg().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently if the host disables VLAN offloads on the VF by
not setting the VIRTCHNL_VF_OFFLOAD_VLAN capability bit
we will still honor VF VLAN configuration messages over
VIRTCHNL. These messages (i.e. enable/disable VLAN stripping
and VLAN filtering) should be blocked when the feature
is not supported. Fix that by adding a helper function to
determine if the VF is allowed to do VLAN operations based
on the host's VF configuration.
Also, mirror the VF communicated capabilities in the host's
VF configuration.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Firmware always returns 8 as the max number of supported TCs. However on
devices with more than 4 ports, the maximum number of TCs per port is
limited to 4. Check and, if necessary, correct the reporting of
capabilities for devices with more than 4 ports.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
One conflict in the BPF samples Makefile, some fixes in 'net' whilst
we were converting over to Makefile.target rules in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the for-loop counter i is a u8 however it is being checked
against a maximum value hw->num_tx_sched_layers which is a u16. Hence
there is a potential wrap-around of counter i back to zero if
hw->num_tx_sched_layers is greater than 255. Fix this by making i
a u16.
Addresses-Coverity: ("Infinite loop")
Fixes: b36c598c99 ("ice: Updates to Tx scheduler code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To help aid in debugging, display the command opcode in debug messages
that print an error code. This makes it easier to see what command
failed if only ICE_DBG_AQ_MSG is enabled.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_debug_cq is passed a mask which is always ICE_DBG_AQ_CMD. Modify this
function, removing the mask parameter entirely, and directly use the more
appropriate ICE_DBG_AQ_DESC and ICE_DBG_AQ_DESC_BUF.
The function is only called from ice_controlq.c, and has no
other callers outside of that file. Move it and mark it static to avoid
namespace pollution.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_vsi_type_str converts an ice_vsi_type enum value to its string
equivalent. This is expected to help easily identify VSI types from
module print statements.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the VLAN ice_flg64_bits are off by 1. Fix this by
setting the ICE_FLG_EVLAN_x8100 flag to 14, which also updates
ICE_FLG_EVLAN_x9100 to 15 and ICE_FLG_VLAN_x8100 to 16.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shorten the delay for SQ responses, but increase the number of loops.
Max delay time is unchanged, but some operations complete much more
quickly.
In the process, add a new define to make the delay count and delay time
more explicit. Add comments to make things more explicit.
This fixes a problem with VF resets failing on with many VFs.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the return value from the Download Package AQ command is stored in
hw->pkg_dwnld_status, use that instead of sq_last_status since that may
have the return value from some other AQ command leading to unexpected
results.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we check to make sure the vector_id passed down from iavf
is less than or equal to pf->hw.func_caps.common_caps.num_msix_vectors.
This is incorrect because the vector_id is always 0-based and never
greater than or equal to the ICE_MAX_INTR_PER_VF. Fix this by checking
to make sure the vector_id is less than the max allowed interrupts per
VF (ICE_MAX_INTR_PER_VF).
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds code to check if PF or VF is disabled before honoring
mailbox message to configure VF - If it is disabled, and opcode is for
resetting VF, the PF driver simply tell VF that all is set. In addition,
if reset is ongoing, and Admin intend to configure VF on the host, we can
poll the VF enabling bit to make sure it is ready before continue - If
after ~250 milliseconds, VF is not in active state, we can bail out with
invalid error.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move software LLDP configuration when FW DCBX is disabled to
ice_init_pf_dcb, since that is where the FW DCBX state is determined.
Remove this software LLDP configuration from ice_vsi_setup and
ice_set_priv_flags. Software configuration includes redirecting Rx LLDP
packets up the stack, when FW DCBX is not running.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the call trace caused by the kernel when the Rx/Tx
descriptor size change request is initiated via ethtool when DCB is
configured. ice_set_ringparam() should use vsi->num_txq instead of
vsi->alloc_txq as it represents the queues that are enabled in the
driver when DCB is enabled/disabled. Otherwise, queue index being
used can go out of range.
For example, when vsi->alloc_txq has 104 queues and with 3 TCS enabled
via DCB, each TC gets 34 queues, vsi->num_txq will be 102 and only 102
queues will be enabled.
Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Certain subsystems behave very badly when called during reset (core
dump). This patch returns -EBUSY when reconfiguring some subsystems
during reset. With this patch some ethtool functions will not core
dump during reset.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement interface layer for the DCBNL subsystem. These are the functions
to support the callbacks defined in the dcbnl_rtnl_ops struct. These
callbacks are going to be used to interface with the DCB settings of the
device. Implementation of dcb_nl set functions and supporting SW DCB
functions.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allow for rate limiting Tx queues. Bitrate is set in
Mbps(megabits per second).
Mbps max-rate is set for the queue via sysfs:
/sys/class/net/<iface>/queues/tx-<queue>/tx_maxrate
ex: echo 100 >/sys/class/net/ens7/queues/tx-0/tx_maxrate
echo 200 >/sys/class/net/ens7/queues/tx-1/tx_maxrate
Note: A value of zero for tx_maxrate means disabled,
default is disabled.
Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
Co-developed-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
DCB configuration flow needs to disable and enable only the PF (main)
VSI, so use ice_ena_vsi and ice_dis_vsi. To avoid the use of ifdef to
control the staticness of these functions, move them to ice_lib.c.
Also replace the allocate and copy of old_cfg to kmemdup() in
ice_pf_dcb_cfg().
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_vc_dis_vf() tells iavf that it's going to perform a reset
and then performs a software reset. This is misleading based on
the function name because the VF does not get disabled. So fix
this by changing the name to ice_vc_reset_vf().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_cleanup_hdrs() has been stripped of most of its content, it only serves
as a wrapper for eth_skb_pad(). We can get rid of it altogether and
simplify the codebase.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The VF_MBX_ARQLEN register array is per-PF, not global, so we should not
use the absolute VF ID as an index. Instead, use the per-PF VF ID.
This fixes an issue with VFs on PFs other than 0 not seeing reset.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
