The lan78xx uses a 12-byte hardware rx header, so there is no need
to allocate SKBs with NET_IP_ALIGN set. Removes alignment faults
in both dwc_otg and in ipv6 processing.
The bInterval is set to 4 (i.e. 8 microframes => 1ms) and the only bit
that the driver pays attention to is "link was reset". If there's a
flapping status bit in that endpoint data, (such as if PHY negotiation
needs a few tries to get a stable link) then polling at a slower rate
would act as a de-bounce.
See: https://github.com/raspberrypi/linux/issues/2447
Enable EEE mode as soon as possible after connecting to the PHY, and
before phy_start. This avoids a second link negotiation, which speeds
up booting and stops the interface failing to become ready.
See: https://github.com/raspberrypi/linux/issues/2437
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add two new DT properties:
* microchip,eee-enabled - a boolean to enable EEE
* microchip,tx-lpi-timer - time in microseconds to wait before entering
low power state
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
For applications of the LAN78xx that don't have valid programmed
EEPROMs or OTPs, enabling both LEDs and auto-negotiation by default
seems reasonable.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
As reported by Eric Dumazet, there are still some outstanding
cases where the driver does not handle TSO correctly when skb's
are over a certain size. Most cases have been fixed, this patch
should ensure that forwarded SKB's that are greater than
MAX_SINGLE_PACKET_SIZE - TX_OVERHEAD are software segmented
and handled correctly.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
lan78xx_tx_bh() makes sure to not exceed MAX_SINGLE_PACKET_SIZE
bytes in the aggregated packets it builds, but does
nothing to prevent large GSO packets being submitted.
Pierre-Francois reported various hangs when/if TSO is enabled.
For localy generated packets, we can use netif_set_gso_max_size()
to limit the size of TSO packets.
Note that forwarded packets could still hit the issue,
so a complete fix might require implementing .ndo_features_check
for this driver, forcing a software segmentation if the size
of the TSO packet exceeds MAX_SINGLE_PACKET_SIZE.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: RENARD Pierre-Francois <pfrenard@gmail.com>
Tested-by: RENARD Pierre-Francois <pfrenard@gmail.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lan78xx driver accesses the PHY registers through MDIO bus over USB
connection. When performing a suspend/resume, the PHY registers can be
accessed before the USB connection is resumed. This will generate an
error and will prevent the device to resume correctly.
This patch adds the dependency between the MDIO bus and USB device to
allow correct handling of suspend/resume.
Fixes: ce85e13ad6 ("lan78xx: Update to use phylib instead of mii_if_info.")
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/usb/lan78xx.c:3995:6: warning:
variable event set but not used [-Wunused-but-set-variable]
It is never used, so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As soon as the netdev is registers, the kernel can start using the
interface. If the driver connects the MAC to the PHY after the netdev
is registered, there is a race condition where the interface can be
opened without having the PHY connected.
Change the order to close this race condition.
Fixes: 92571a1aae ("lan78xx: Connect phy early")
Reported-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In lan78xx_probe(), a new urb is allocated through usb_alloc_urb() and
saved to 'dev->urb_intr'. However, in the following execution, if an error
occurs, 'dev->urb_intr' is not deallocated, leading to memory leaks. To fix
this issue, invoke usb_free_urb() to free the allocated urb before
returning from the function.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge the combo uses of cpu_to_le32s and memcpy.
Use put_unaligned_le32 instead.
This simplifies the code.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge the combo use of memcpy and lexx_to_cpus.
Use get_unaligned_lexx instead.
This simplifies the code.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Acked-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All users of the fixed_phy_add() pass -1 as GPIO number
to the fixed phy driver, and all users of fixed_phy_register()
pass -1 as GPIO number as well, except for the device
tree MDIO bus.
Any new users should create a proper device and pass the
GPIO as a descriptor associated with the device so delete
the GPIO argument from the calls and drop the code looking
requesting a GPIO in fixed_phy_add().
In fixed phy_register(), investigate the "fixed-link"
node and pick the GPIO descriptor from "link-gpios" if
this property exists. Move the corresponding code out
of of_mdio.c as the fixed phy code anyways requires
OF to be in use.
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
Current state for the lan78xx driver does not allow for changing the
MAC address of the interface, without either removing the module (if
you compiled it that way) or rebooting the machine. If you attempt to
change the MAC address, ifconfig will show the new address, however,
the system/interface will not respond to any traffic using that
configuration. A few short-term options to work around this are to
unload the module and reload it with the new MAC address, change the
interface to "promisc", or reboot with the correct configuration to
change the MAC.
This patch enables the ability to change the MAC address via fairly normal means...
ifdown <interface>
modify entry in /etc/network/interfaces OR a similar method
ifup <interface>
Then test via any network communication, such as ICMP requests to gateway.
My only test platform for this patch has been a raspberry pi model 3b+.
Signed-off-by: Jason Martinsen <jasonmartinsen@msn.com>
-----
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few MAC/PHYs combinations which now support > 1Gbps. These
may need to make use of link modes with bits > 31. Thus their
supported PHY features or advertised features cannot be implemented
using the current bitmap in a u32. Convert to using a linkmode bitmap,
which can support all the currently devices link modes, and is future
proof as more modes are added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflict in net/core/rtnetlink.c, David Ahern's bug fix in 'net'
overlapped the renaming of a netlink attribute in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver supports a fair amount of Wake-on-LAN modes, but is not
checking that the user specified one that is supported.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Woojung Huh <Woojung.Huh@Microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns when a variable is assigned to itself.
drivers/net/usb/lan78xx.c:940:11: warning: explicitly assigning value of
variable of type 'u32' (aka 'unsigned int') to itself [-Wself-assign]
offset = offset;
~~~~~~ ^ ~~~~~~
1 warning generated.
Reorder the if statement to acheive the same result and avoid a self
assignment warning.
Link: https://github.com/ClangBuiltLinux/linux/issues/129
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put has taken the null pointer check into account. So it is
safe to remove the duplicated check before of_node_put.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some MAC hardware cannot support a subset of link modes. e.g. often
1Gbps Full duplex is supported, but Half duplex is not. Add a helper
to remove such a link mode.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use skb_queue_walk() instead.
Adjust inner loop test to utilize and skb_queue_is_first().
Unfortunately we have to keep pkt_cnt around because it is
used by a latter loop in this function.
Signed-off-by: David S. Miller <davem@davemloft.net>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to bail out if lan78xx_get_endpoints() fails, otherwise the
result is overwritten.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Raghuram Chary Jallipalli <raghuramchary.jallipalli@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use ARRAY_SIZE to replace open code sizeof(lan78xx_regs) / sizeof(u32).
It make the code concise.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BTF conflicts were simple overlapping changes.
The virtio_net conflict was an overlap of a fix of statistics counter,
happening alongisde a move over to a bonafide statistics structure
rather than counting value on the stack.
Signed-off-by: David S. Miller <davem@davemloft.net>
As long the bh tasklet isn't scheduled once, no packet from the rx path
will be handled. Since the tx path also schedule the same tasklet
this situation only persits until the first packet transmission.
So fix this issue by scheduling the tasklet after link reset.
Link: https://github.com/raspberrypi/linux/issues/2617
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet")
Suggested-by: Floris Bos <bos@je-eigen-domein.nl>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb size calculation in lan78xx_tx_bh is in race with the start_xmit,
which could lead to rare kernel oopses. So protect the whole skb walk with
a spin lock. As a benefit we can unlink the skb directly.
This patch was tested on Raspberry Pi 3B+
Link: https://github.com/raspberrypi/linux/issues/2608
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Floris Bos <bos@je-eigen-domein.nl>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple overlapping changes in stmmac driver.
Adjust skb_gro_flush_final_remcsum function signature to make GRO list
changes in net-next, as per Stephen Rothwell's example merge
resolution.
Signed-off-by: David S. Miller <davem@davemloft.net>
Observations of VLANs dropping packets due to invalid
checksums when not offloading VLAN tag receive.
With VLAN tag stripping enabled no issue is observed.
Drop back to s/w checksums if VLAN offload is disabled.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip supports stripping the VLAN tag and reporting it
in metadata.
Complete the support for this.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW_VLAN_CTAG_FILTER was partially implemented, but not advertised
to Linux.
Complete the implementation of this.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The frame abort timeout being set by lan78xx_set_rx_max_frame_length
didn't account for any VLAN headers, resulting in very low
throughput if used with tagged VLANs.
Use VLAN_ETH_HLEN instead of ETH_HLEN to correct for this.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
random_ether_addr is a #define for eth_random_addr which is
generally preferred in kernel code by ~3:1
Convert the uses of random_ether_addr to enable removing the #define
Miscellanea:
o Convert &vfmac[0] to equivalent vfmac and avoid unnecessary line wrap
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of drivers have the following pattern:
if (np)
of_mdiobus_register()
else
mdiobus_register()
which the implementation of of_mdiobus_register() now takes care of.
Remove that pattern in drivers that strictly adhere to it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
