1974 Commits

Author	SHA1	Message	Date
Jonathan Bell	8b4d883809	usb: add plumbing for updating interrupt endpoint interval state ... xHCI caches device and endpoint data after the interface is configured, so an explicit command needs to be issued for any device driver wanting to alter the polling interval of an endpoint. Add usb_fixup_endpoint() to allow drivers to do this. The fixup must be called after calculating endpoint bandwidth requirements but before any URBs are submitted. If polling intervals are shortened, any bandwidth reservations are no longer valid but in practice polling intervals are only ever relaxed. Limit the scope to interrupt transfers for now. Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>	2020-05-20 13:49:09 +01:00
popcornmix	706b4eb9dd	Add dwc_otg driver ... Signed-off-by: popcornmix <popcornmix@gmail.com> usb: dwc: fix lockdep false positive Signed-off-by: Kari Suvanto <karis79@gmail.com> usb: dwc: fix inconsistent lock state Signed-off-by: Kari Suvanto <karis79@gmail.com> Add FIQ patch to dwc_otg driver. Enable with dwc_otg.fiq_fix_enable=1. Should give about 10% more ARM performance. Thanks to Gordon and Costas Avoid dynamic memory allocation for channel lock in USB driver. Thanks ddv2005. Add NAK holdoff scheme. Enabled by default, disable with dwc_otg.nak_holdoff_enable=0. Thanks gsh Make sure we wait for the reset to finish dwc_otg: fix bug in dwc_otg_hcd.c resulting in silent kernel memory corruption, escalating to OOPS under high USB load. dwc_otg: Fix unsafe access of QTD during URB enqueue In dwc_otg_hcd_urb_enqueue during qtd creation, it was possible that the transaction could complete almost immediately after the qtd was assigned to a host channel during URB enqueue, which meant the qtd pointer was no longer valid having been completed and removed. Usually, this resulted in an OOPS during URB submission. By predetermining whether transactions need to be queued or not, this unsafe pointer access is avoided. This bug was only evident on the Pi model A where a device was attached that had no periodic endpoints (e.g. USB pendrive or some wlan devices). dwc_otg: Fix incorrect URB allocation error handling If the memory allocation for a dwc_otg_urb failed, the kernel would OOPS because for some reason a member of the *unallocated* struct was set to zero. Error handling changed to fail correctly. dwc_otg: fix potential use-after-free case in interrupt handler If a transaction had previously aborted, certain interrupts are enabled to track error counts and reset where necessary. On IN endpoints the host generates an ACK interrupt near-simultaneously with completion of transfer. In the case where this transfer had previously had an error, this results in a use-after-free on the QTD memory space with a 1-byte length being overwritten to 0x00. dwc_otg: add handling of SPLIT transaction data toggle errors Previously a data toggle error on packets from a USB1.1 device behind a TT would result in the Pi locking up as the driver never handled the associated interrupt. Patch adds basic retry mechanism and interrupt acknowledgement to cater for either a chance toggle error or for devices that have a broken initial toggle state (FT8U232/FT232BM). dwc_otg: implement tasklet for returning URBs to usbcore hcd layer The dwc_otg driver interrupt handler for transfer completion will spend a very long time with interrupts disabled when a URB is completed - this is because usb_hcd_giveback_urb is called from within the handler which for a USB device driver with complicated processing (e.g. webcam) will take an exorbitant amount of time to complete. This results in missed completion interrupts for other USB packets which lead to them being dropped due to microframe overruns. This patch splits returning the URB to the usb hcd layer into a high-priority tasklet. This will have most benefit for isochronous IN transfers but will also have incidental benefit where multiple periodic devices are active at once. dwc_otg: fix NAK holdoff and allow on split transactions only This corrects a bug where if a single active non-periodic endpoint had at least one transaction in its qh, on frnum == MAX_FRNUM the qh would get skipped and never get queued again. This would result in a silent device until error detection (automatic or otherwise) would either reset the device or flush and requeue the URBs. Additionally the NAK holdoff was enabled for all transactions - this would potentially stall a HS endpoint for 1ms if a previous error state enabled this interrupt and the next response was a NAK. Fix so that only split transactions get held off. dwc_otg: Call usb_hcd_unlink_urb_from_ep with lock held in completion handler usb_hcd_unlink_urb_from_ep must be called with the HCD lock held. Calling it asynchronously in the tasklet was not safe (regression in c4564d4a1a). This change unlinks it from the endpoint prior to queueing it for handling in the tasklet, and also adds a check to ensure the urb is OK to be unlinked before doing so. NULL pointer dereference kernel oopses had been observed in usb_hcd_giveback_urb when a USB device was unplugged/replugged during data transfer. This effect was reproduced using automated USB port power control, hundreds of replug events were performed during active transfers to confirm that the problem was eliminated. USB fix using a FIQ to implement split transactions This commit adds a FIQ implementaion that schedules the split transactions using a FIQ so we don't get held off by the interrupt latency of Linux dwc_otg: fix device attributes and avoid kernel warnings on boot dcw_otg: avoid logging function that can cause panics See: https://github.com/raspberrypi/firmware/issues/21 Thanks to cleverca22 for fix dwc_otg: mask correct interrupts after transaction error recovery The dwc_otg driver will unmask certain interrupts on a transaction that previously halted in the error state in order to reset the QTD error count. The various fine-grained interrupt handlers do not consider that other interrupts besides themselves were unmasked. By disabling the two other interrupts only ever enabled in DMA mode for this purpose, we can avoid unnecessary function calls in the IRQ handler. This will also prevent an unneccesary FIQ interrupt from being generated if the FIQ is enabled. dwc_otg: fiq: prevent FIQ thrash and incorrect state passing to IRQ In the case of a transaction to a device that had previously aborted due to an error, several interrupts are enabled to reset the error count when a device responds. This has the side-effect of making the FIQ thrash because the hardware will generate multiple instances of a NAK on an IN bulk/interrupt endpoint and multiple instances of ACK on an OUT bulk/interrupt endpoint. Make the FIQ mask and clear the associated interrupts. Additionally, on non-split transactions make sure that only unmasked interrupts are cleared. This caused a hard-to-trigger but serious race condition when you had the combination of an endpoint awaiting error recovery and a transaction completed on an endpoint - due to the sequencing and timing of interrupts generated by the dwc_otg core, it was possible to confuse the IRQ handler. Fix function tracing dwc_otg: whitespace cleanup in dwc_otg_urb_enqueue dwc_otg: prevent OOPSes during device disconnects The dwc_otg_urb_enqueue function is thread-unsafe. In particular the access of urb->hcpriv, usb_hcd_link_urb_to_ep, dwc_otg_urb->qtd and friends does not occur within a critical section and so if a device was unplugged during activity there was a high chance that the usbcore hub_thread would try to disable the endpoint with partially- formed entries in the URB queue. This would result in BUG() or null pointer dereferences. Fix so that access of urb->hcpriv, enqueuing to the hardware and adding to usbcore endpoint URB lists is contained within a single critical section. dwc_otg: prevent BUG() in TT allocation if hub address is > 16 A fixed-size array is used to track TT allocation. This was previously set to 16 which caused a crash because dwc_otg_hcd_allocate_port would read past the end of the array. This was hit if a hub was plugged in which enumerated as addr > 16, due to previous device resets or unplugs. Also add #ifdef FIQ_DEBUG around hcd->hub_port_alloc[], which grows to a large size if 128 hub addresses are supported. This field is for debug only for tracking which frame an allocate happened in. dwc_otg: make channel halts with unknown state less damaging If the IRQ received a channel halt interrupt through the FIQ with no other bits set, the IRQ would not release the host channel and never complete the URB. Add catchall handling to treat as a transaction error and retry. dwc_otg: fiq_split: use TTs with more granularity This fixes certain issues with split transaction scheduling. - Isochronous multi-packet OUT transactions now hog the TT until they are completed - this prevents hubs aborting transactions if they get a periodic start-split out-of-order - Don't perform TT allocation on non-periodic endpoints - this allows simultaneous use of the TT's bulk/control and periodic transaction buffers This commit will mainly affect USB audio playback. dwc_otg: fix potential sleep while atomic during urb enqueue Fixes a regression introduced with eb1b482a. Kmalloc called from dwc_otg_hcd_qtd_add / dwc_otg_hcd_qtd_create did not always have the GPF_ATOMIC flag set. Force this flag when inside the larger critical section. dwc_otg: make fiq_split_enable imply fiq_fix_enable Failing to set up the FIQ correctly would result in "IRQ 32: nobody cared" errors in dmesg. dwc_otg: prevent crashes on host port disconnects Fix several issues resulting in crashes or inconsistent state if a Model A root port was disconnected. - Clean up queue heads properly in kill_urbs_in_qh_list by removing the empty QHs from the schedule lists - Set the halt status properly to prevent IRQ handlers from using freed memory - Add fiq_split related cleanup for saved registers - Make microframe scheduling reclaim host channels if active during a disconnect - Abort URBs with -ESHUTDOWN status response, informing device drivers so they respond in a more correct fashion and don't try to resubmit URBs - Prevent IRQ handlers from attempting to handle channel interrupts if the associated URB was dequeued (and the driver state was cleared) dwc_otg: prevent leaking URBs during enqueue A dwc_otg_urb would get leaked if the HCD enqueue function failed for any reason. Free the URB at the appropriate points. dwc_otg: Enable NAK holdoff for control split transactions Certain low-speed devices take a very long time to complete a data or status stage of a control transaction, producing NAK responses until they complete internal processing - the USB2.0 spec limit is up to 500mS. This causes the same type of interrupt storm as seen with USB-serial dongles prior to c8edb238. In certain circumstances, usually while booting, this interrupt storm could cause SD card timeouts. dwc_otg: Fix for occasional lockup on boot when doing a USB reset dwc_otg: Don't issue traffic to LS devices in FS mode Issuing low-speed packets when the root port is in full-speed mode causes the root port to stop responding. Explicitly fail when enqueuing URBs to a LS endpoint on a FS bus. Fix ARM architecture issue with local_irq_restore() If local_fiq_enable() is called before a local_irq_restore(flags) where the flags variable has the F bit set, the FIQ will be erroneously disabled. Fixup arch_local_irq_restore to avoid trampling the F bit in CPSR. Also fix some of the hacks previously implemented for previous dwc_otg incarnations. dwc_otg: fiq_fsm: Base commit for driver rewrite This commit removes the previous FIQ fixes entirely and adds fiq_fsm. This rewrite features much more complete support for split transactions and takes into account several OTG hardware bugs. High-speed isochronous transactions are also capable of being performed by fiq_fsm. All driver options have been removed and replaced with: - dwc_otg.fiq_enable (bool) - dwc_otg.fiq_fsm_enable (bool) - dwc_otg.fiq_fsm_mask (bitmask) - dwc_otg.nak_holdoff (unsigned int) Defaults are specified such that fiq_fsm behaves similarly to the previously implemented FIQ fixes. fiq_fsm: Push error recovery into the FIQ when fiq_fsm is used If the transfer associated with a QTD failed due to a bus error, the HCD would retry the transfer up to 3 times (implementing the USB2.0 three-strikes retry in software). Due to the masking mechanism used by fiq_fsm, it is only possible to pass a single interrupt through to the HCD per-transfer. In this instance host channels would fall off the radar because the error reset would function, but the subsequent channel halt would be lost. Push the error count reset into the FIQ handler. fiq_fsm: Implement timeout mechanism For full-speed endpoints with a large packet size, interrupt latency runs the risk of the FIQ starting a transaction too late in a full-speed frame. If the device is still transmitting data when EOF2 for the downstream frame occurs, the hub will disable the port. This change is not reflected in the hub status endpoint and the device becomes unresponsive. Prevent high-bandwidth transactions from being started too late in a frame. The mechanism is not guaranteed: a combination of bit stuffing and hub latency may still result in a device overrunning. fiq_fsm: fix bounce buffer utilisation for Isochronous OUT Multi-packet isochronous OUT transactions were subject to a few bounday bugs. Fix them. Audio playback is now much more robust: however, an issue stands with devices that have adaptive sinks - ALSA plays samples too fast. dwc_otg: Return full-speed frame numbers in HS mode The frame counter increments on every *microframe* in high-speed mode. Most device drivers expect this number to be in full-speed frames - this caused considerable confusion to e.g. snd_usb_audio which uses the frame counter to estimate the number of samples played. fiq_fsm: save PID on completion of interrupt OUT transfers Also add edge case handling for interrupt transports. Note that for periodic split IN, data toggles are unimplemented in the OTG host hardware - it unconditionally accepts any PID. fiq_fsm: add missing case for fiq_fsm_tt_in_use() Certain combinations of bitrate and endpoint activity could result in a periodic transaction erroneously getting started while the previous Isochronous OUT was still active. fiq_fsm: clear hcintmsk for aborted transactions Prevents the FIQ from erroneously handling interrupts on a timed out channel. fiq_fsm: enable by default fiq_fsm: fix dequeues for non-periodic split transactions If a dequeue happened between the SSPLIT and CSPLIT phases of the transaction, the HCD would never receive an interrupt. fiq_fsm: Disable by default fiq_fsm: Handle HC babble errors The HCTSIZ transfer size field raises a babble interrupt if the counter wraps. Handle the resulting interrupt in this case. dwc_otg: fix interrupt registration for fiq_enable=0 Additionally make the module parameter conditional for wherever hcd->fiq_state is touched. fiq_fsm: Enable by default dwc_otg: Fix various issues with root port and transaction errors Process the host port interrupts correctly (and don't trample them). Root port hotplug now functional again. Fix a few thinkos with the transaction error passthrough for fiq_fsm. fiq_fsm: Implement hack for Split Interrupt transactions Hubs aren't too picky about which endpoint we send Control type split transactions to. By treating Interrupt transfers as Control, it is possible to use the non-periodic queue in the OTG core as well as the non-periodic FIFOs in the hub itself. This massively reduces the microframe exclusivity/contention that periodic split transactions otherwise have to enforce. It goes without saying that this is a fairly egregious USB specification violation, but it works. Original idea by Hans Petter Selasky @ FreeBSD.org. dwc_otg: FIQ support on SMP. Set up FIQ stack and handler on Core 0 only. dwc_otg: introduce fiq_fsm_spin(un|)lock() SMP safety for the FIQ relies on register read-modify write cycles being completed in the correct order. Several places in the DWC code modify registers also touched by the FIQ. Protect these by a bare-bones lock mechanism. This also makes it possible to run the FIQ and IRQ handlers on different cores. fiq_fsm: fix build on bcm2708 and bcm2709 platforms dwc_otg: put some barriers back where they should be for UP bcm2709/dwc_otg: Setup FIQ on core 1 if >1 core active dwc_otg: fixup read-modify-write in critical paths Be more careful about read-modify-write on registers that the FIQ also touches. Guard fiq_fsm_spin_lock with fiq_enable check fiq_fsm: Falling out of the state machine isn't fatal This edge case can be hit if the port is disabled while the FIQ is in the middle of a transaction. Make the effects less severe. Also get rid of the useless return value. squash: dwc_otg: Allow to build without SMP usb: core: make overcurrent messages more prominent Hub overcurrent messages are more serious than "debug". Increase loglevel. usb: dwc_otg: Don't use dma_to_virt() Commit 6ce0d20 changes dma_to_virt() which breaks this driver. Open code the old dma_to_virt() implementation to work around this. Limit the use of __bus_to_virt() to cases where transfer_buffer_length is set and transfer_buffer is not set. This is done to increase the chance that this driver will also work on ARCH_BCM2835. transfer_buffer should not be NULL if the length is set, but the comment in the code indicates that there are situations where this might happen. drivers/usb/isp1760/isp1760-hcd.c also has a similar comment pointing to a possible: 'usb storage / SCSI bug'. Signed-off-by: Noralf Trønnes <noralf@tronnes.org> dwc_otg: Fix crash when fiq_enable=0 dwc_otg: fiq_fsm: Make high-speed isochronous strided transfers work properly Certain low-bandwidth high-speed USB devices (specialist audio devices, compressed-frame webcams) have packet intervals > 1 microframe. Stride these transfers in the FIQ by using the start-of-frame interrupt to restart the channel at the right time. dwc_otg: Force host mode to fix incorrect compute module boards dwc_otg: Add ARCH_BCM2835 support Signed-off-by: Noralf Trønnes <noralf@tronnes.org> dwc_otg: Simplify FIQ irq number code Dropping ATAGS means we can simplify the FIQ irq number code. Also add error checking on the returned irq number. Signed-off-by: Noralf Trønnes <noralf@tronnes.org> dwc_otg: Remove duplicate gadget probe/unregister function dwc_otg: Properly set the HFIR Douglas Anderson reported: According to the most up to date version of the dwc2 databook, the FRINT field of the HFIR register should be programmed to: * 125 us * (PHY clock freq for HS) - 1 * 1000 us * (PHY clock freq for FS/LS) - 1 This is opposed to older versions of the doc that claimed it should be: * 125 us * (PHY clock freq for HS) * 1000 us * (PHY clock freq for FS/LS) and reported lower timing jitter on a USB analyser dcw_otg: trim xfer length when buffer larger than allocated size is received dwc_otg: Don't free qh align buffers in atomic context dwc_otg: Enable the hack for Split Interrupt transactions by default dwc_otg.fiq_fsm_mask=0xF has long been a suggestion for users with audio stutters or other USB bandwidth issues. So far we are aware of many success stories but no failure caused by this setting. Make it a default to learn more. See: https://www.raspberrypi.org/forums/viewtopic.php?f=28&t=70437 Signed-off-by: popcornmix <popcornmix@gmail.com> dwc_otg: Use kzalloc when suitable dwc_otg: Pass struct device to dma_alloc*() This makes it possible to get the bus address from Device Tree. Signed-off-by: Noralf Trønnes <noralf@tronnes.org> dwc_otg: fix summarize urb->actual_length for isochronous transfers Kernel does not copy input data of ISO transfers to userspace if actual_length is set only in ISO transfers and not summarized in urb->actual_length. Fixes raspberrypi/linux#903 fiq_fsm: Use correct states when starting isoc OUT transfers In fiq_fsm_start_next_periodic() if an isochronous OUT transfer was selected, no regard was given as to whether this was a single-packet transfer or a multi-packet staged transfer. For single-packet transfers, this had the effect of repeatedly sending OUT packets with bogus data and lengths. Eventually if the channel was repeatedly enabled enough times, this would lock up the OTG core and no further bus transfers would happen. Set the FSM state up properly if we select a single-packet transfer. Fixes https://github.com/raspberrypi/linux/issues/1842 dwc_otg: make nak_holdoff work as intended with empty queues If URBs reading from non-periodic split endpoints were dequeued and the last transfer from the endpoint was a NAK handshake, the resulting qh->nak_frame value was stale which would result in unnecessarily long polling intervals for the first subsequent transfer with a fresh URB. Fixup qh->nak_frame in dwc_otg_hcd_urb_dequeue and also guard against a case where a single URB is submitted to the endpoint, a NAK was received on the transfer immediately prior to receiving data and the device subsequently resubmits another URB past the qh->nak_frame interval. Fixes https://github.com/raspberrypi/linux/issues/1709 dwc_otg: fix split transaction data toggle handling around dequeues See https://github.com/raspberrypi/linux/issues/1709 Fix several issues regarding endpoint state when URBs are dequeued - If the HCD is disconnected, flush FIQ-enabled channels properly - Save the data toggle state for bulk endpoints if the last transfer from an endpoint where URBs were dequeued returned a data packet - Reset hc->start_pkt_count properly in assign_and_init_hc() dwc_otg: fix several potential crash sources On root port disconnect events, the host driver state is cleared and in-progress host channels are forcibly stopped. This doesn't play well with the FIQ running in the background, so: - Guard the disconnect callback with both the host spinlock and FIQ spinlock - Move qtd dereference in dwc_otg_handle_hc_fsm() after the early-out so we don't dereference a qtd that has gone away - Turn catch-all BUG()s in dwc_otg_handle_hc_fsm() into warnings. dwc_otg: delete hcd->channel_lock The lock serves no purpose as it is only held while the HCD spinlock is already being held. dwc_otg: remove unnecessary dma-mode channel halts on disconnect interrupt Host channels are already halted in kill_urbs_in_qh_list() with the subsequent interrupt processing behaving as if the URB was dequeued via HCD callback. There's no need to clobber the host channel registers a second time as this exposes races between the driver and host channel resulting in hcd->free_hc_list becoming corrupted. dwcotg: Allow to build without FIQ on ARM64 Signed-off-by: popcornmix <popcornmix@gmail.com> dwc_otg: make periodic scheduling behave properly for FS buses If the root port is in full-speed mode, transfer times at 12mbit/s would be calculated but matched against high-speed quotas. Reinitialise hcd->frame_usecs[i] on each port enable event so that full-speed bandwidth can be tracked sensibly. Also, don't bother using the FIQ for transfers when in full-speed mode - at the slower bus speed, interrupt frequency is reduced by an order of magnitude. Related issue: https://github.com/raspberrypi/linux/issues/2020 dwc_otg: fiq_fsm: Make isochronous compatibility checks work properly Get rid of the spammy printk and local pointer mangling. Also, there is a nominal benefit for using fiq_fsm for isochronous transfers in FS mode (~1.1k IRQs per second vs 2.1k IRQs per second) so remove the root port speed check. dwc_otg: add module parameter int_ep_interval_min Add a module parameter (defaulting to ignored) that clamps the polling rate of high-speed Interrupt endpoints to a minimum microframe interval. The parameter is modifiable at runtime as it is used when activating new endpoints (such as on device connect). dwc_otg: fiq_fsm: Add non-periodic TT exclusivity constraints Certain hub types do not discriminate between pipe direction (IN or OUT) when considering non-periodic transfers. Therefore these hubs get confused if multiple transfers are issued in different directions with the same device address and endpoint number. Constrain queuing non-periodic split transactions so they are performed serially in such cases. Related: https://github.com/raspberrypi/linux/issues/2024 dwc_otg: Fixup change to DRIVER_ATTR interface dwc_otg: Fix compilation warnings Signed-off-by: Phil Elwell <phil@raspberrypi.org> USB_DWCOTG: Disable building dwc_otg as a module (#2265) When dwc_otg is built as a module, build will fail with the following error: ERROR: "DWC_TASK_HI_SCHEDULE" [drivers/usb/host/dwc_otg/dwc_otg.ko] undefined! scripts/Makefile.modpost:91: recipe for target '__modpost' failed make[1]: *** [__modpost] Error 1 Makefile:1199: recipe for target 'modules' failed make: *** [modules] Error 2 Even if the error is solved by including the missing DWC_TASK_HI_SCHEDULE function, the kernel will panic when loading dwc_otg. As a workaround, simply prevent user from building dwc_otg as a module as the current kernel does not support it. See: https://github.com/raspberrypi/linux/issues/2258 Signed-off-by: Malik Olivier Boussejra <malik@boussejra.com> dwc_otg: New timer API dwc_otg: Fix removed ACCESS_ONCE->READ_ONCE dwc_otg: don't unconditionally force host mode in dwc_otg_cil_init() Add the ability to disable force_host_mode for those that want to use dwc_otg in both device and host modes. dwc_otg: Fix a regression when dequeueing isochronous transfers In 282bed95 (dwc_otg: make nak_holdoff work as intended with empty queues) the dequeue mechanism was changed to leave FIQ-enabled transfers to run to completion - to avoid leaving hub TT buffers with stale packets lying around. This broke FIQ-accelerated isochronous transfers, as this then meant that dozens of transfers were performed after the dequeue function returned. Restore the state machine fence for isochronous transfers. fiq_fsm: rewind DMA pointer for OUT transactions that fail (#2288) See: https://github.com/raspberrypi/linux/issues/2140 dwc_otg: add smp_mb() to prevent driver state corruption on boot Occasional crashes have been seen where the FIQ code dereferences invalid/random pointers immediately after being set up, leading to panic on boot. The crash occurs as the FIQ code races against hcd_init_fiq() and the hcd_init_fiq() code races against the outstanding memory stores from dwc_otg_hcd_init(). Use explicit barriers after touching driver state. usb: dwc_otg: fix memory corruption in dwc_otg driver [Upstream commit 51b1b64917] The move from the staging tree to the main tree exposed a longstanding memory corruption bug in the dwc2 driver. The reordering of the driver initialization caused the dwc2 driver to corrupt the initialization data of the sdhci driver on the Raspberry Pi platform, which made the bug show up. The error is in calling to_usb_device(hsotg->dev), since ->dev is not a member of struct usb_device. The easiest fix is to just remove the offending code, since it is not really needed. Thanks to Stephen Warren for tracking down the cause of this. Reported-by: Andre Heider <a.heider@gmail.com> Tested-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [lukas: port from upstream dwc2 to out-of-tree dwc_otg driver] Signed-off-by: Lukas Wunner <lukas@wunner.de> usb: dwb_otg: Fix unreachable switch statement warning This warning appears with GCC 7.3.0 from toolchains.bootlin.com: ../drivers/usb/host/dwc_otg/dwc_otg_fiq_fsm.c: In function ‘fiq_fsm_update_hs_isoc’: ../drivers/usb/host/dwc_otg/dwc_otg_fiq_fsm.c:595:61: warning: statement will never be executed [-Wswitch-unreachable] st->hctsiz_copy.b.xfersize = nrpackets * st->hcchar_copy.b.mps; ~~~~~~~~~~~~~~~~~^~~~ Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> dwc_otg: fiq_fsm: fix incorrect DMA register offset calculation Rationalise the offset and update all call sites. Fixes https://github.com/raspberrypi/linux/issues/2408 dwc_otg: fix bug with port_addr assignment for single-TT hubs See https://github.com/raspberrypi/linux/issues/2734 The "Hub Port" field in the split transaction packet was always set to 1 for single-TT hubs. The majority of single-TT hub products apparently ignore this field and broadcast to all downstream enabled ports, which masked the issue. A subset of hub devices apparently need the port number to be exact or split transactions will fail. usb: dwc_otg: Clean up build warnings on 64bit kernels No functional changes. Almost all are changes to logging lines. Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org> usb: dwc_otg: Use dma allocation for mphi dummy_send buffer The FIQ driver used a kzalloc'ed buffer for dummy_send, passing a kernel virtual address to the hardware block. The buffer is only ever used for a dummy read, so it should be harmless, but there is the chance that it will cause exceptions. Use a dma allocation so that we have a genuine bus address, and read from that. Free the allocation when done for good measure. Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org> dwc_otg: only do_split when we actually need to do a split The previous test would fail if the root port was in fullspeed mode and there was a hub between the FS device and the root port. While the transfer worked, the schedule mangling performed for high-speed split transfers would break leading to an 8ms polling interval. dwc_otg: fix locking around dequeueing and killing URBs kill_urbs_in_qh_list() is practically only ever called with the fiq lock already held, so don't spinlock twice in the case where we need to cancel an isochronous transfer. Also fix up a case where the global interrupt register could be read with the fiq lock not held. Fixes the deadlock seen in https://github.com/raspberrypi/linux/issues/2907 ARM64/DWC_OTG: Port dwc_otg driver to ARM64 In ARM64, the FIQ mechanism used by this driver is not current implemented. As a workaround, reqular IRQ is used instead of FIQ. In a separate change, the IRQ-CPU mapping is round robined on ARM64 to increase concurrency and allow multiple interrupts to be serviced at a time. This reduces the need for FIQ. Tests Run: This mechanism is most likely to break when multiple USB devices are attached at the same time. So the system was tested under stress. Devices: 1. USB Speakers playing back a FLAC audio through VLC at 96KHz.(Higher then typically, but supported on my speakers). 2. sftp transferring large files through the buildin ethernet connection which is connected through USB. 3. Keyboard and mouse attached and being used. Although I do occasionally hear some glitches, the music seems to play quite well. Signed-off-by: Michael Zoran <mzoran@crowfest.net> usb: dwc_otg: Clean up interrupt claiming code The FIQ/IRQ interrupt number identification code is scattered through the dwc_otg driver. Rationalise it, simplifying the code and solving an existing issue. See: https://github.com/raspberrypi/linux/issues/2612 Signed-off-by: Phil Elwell <phil@raspberrypi.org> dwc_otg: Choose appropriate IRQ handover strategy 2711 has no MPHI peripheral, but the ARM Control block can fake interrupts. Use the size of the DTB "mphi" reg block to determine which is required. Signed-off-by: Phil Elwell <phil@raspberrypi.org> usb: host: dwc_otg: fix compiling in separate directory The dwc_otg Makefile does not respect the O=path argument correctly: include paths in CFLAGS are given relatively to object path, not source path. Compiling in a separate directory yields #include errors. Signed-off-by: Marek Behún <marek.behun@nic.cz> dwc_otg: use align_buf for small IN control transfers (#3150) The hardware will do a 4-byte write to memory on any IN packet received that is between 1 and 3 bytes long. This tramples memory in the uvcvideo driver, as it uses a sequence of 1- and 2-byte control transfers to query the min/max/range/step of each individual camera control and gives us buffers that are offsets into a struct. Catch small control transfers in the data phase and use the align_buf to bounce the correct number of bytes into the URB's buffer. In general, short packets on non-control endpoints should be OK as URBs should have enough buffer space for a wMaxPacket size transfer. See: https://github.com/raspberrypi/linux/issues/3148 Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org> dwc_otg: Declare DMA capability with HCD_DMA flag Following [1], USB controllers have to declare DMA capabilities in order for them to be used by adding the HCD_DMA flag to their hc_driver struct. [1] 7b81cb6bdd ("usb: add a HCD_DMA flag instead of guestimating DMA capabilities") Signed-off-by: Phil Elwell <phil@raspberrypi.org> dwc_otg: checking the urb->transfer_buffer too early (#3332) After enable the HIGHMEM and VMSPLIT_3G, the dwc_otg driver doesn't work well on Pi2/3 boards with 1G physical ram. Users experience the failure when copying a file of 600M size to the USB stick. And at the same time, the dmesg shows: usb 1-1.1.2: reset high-speed USB device number 8 using dwc_otg sd 0:0:0:0: [sda] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK blk_update_request: I/O error, dev sda, sector 3024048 op 0x1:(WRITE) flags 0x4000 phys_seg 15 prio class 0 When this happens, the sg_buf sent to the driver is located in the highmem region, the usb_sg_init() in the core/message.c will leave transfer_buffer to NULL if the sg_buf is in highmem, but in the dwc_otg driver, it returns -EINVAL unconditionally if transfer_buffer is NULL. The driver can handle the situation of buffer to be NULL, if it is in DMA mode, it will convert an address from transfer_dma. But if the conversion fails or it is in the PIO mode, we should check buffer and return -EINVAL if it is NULL. BugLink: https://bugs.launchpad.net/bugs/1852510 Signed-off-by: Hui Wang <hui.wang@canonical.com>	2020-05-20 13:48:47 +01:00
Hans de Goede	3d456cb5a8	usb: quirks: add NO_LPM quirk for RTL8153 based ethernet adapters ... commit 75d7676ead upstream. We have been receiving bug reports that ethernet connections over RTL8153 based ethernet adapters stops working after a while with errors like these showing up in dmesg when the ethernet stops working: [12696.189484] r8152 6-1:1.0 enp10s0u1: Tx timeout [12702.333456] r8152 6-1:1.0 enp10s0u1: Tx timeout [12707.965422] r8152 6-1:1.0 enp10s0u1: Tx timeout This has been reported on Dell WD15 docks, Belkin USB-C Express Dock 3.1 docks and with generic USB to ethernet dongles using the RTL8153 chipsets. Some users have tried adding usbcore.quirks=0bda:8153:k to the kernel commandline and all users who have tried this report that this fixes this. Also note that we already have an existing NO_LPM quirk for the RTL8153 used in the Microsoft Surface Dock (where it uses a different usb-id). This commit adds a NO_LPM quirk for the generic Realtek RTL8153 0bda:8153 usb-id, fixing the Tx timeout errors on these devices. BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=198931 Cc: stable@vger.kernel.org Cc: russianneuromancer@ya.ru Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20200313120708.100339-1-hdegoede@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2020-03-25 08:26:59 +01:00
Kai-Heng Feng	e9b5c04bc3	USB: Disable LPM on WD19's Realtek Hub ... commit b63e48fb50 upstream. Realtek Hub (0bda:0x0487) used in Dell Dock WD19 sometimes drops off the bus when bringing underlying ports from U3 to U0. Disabling LPM on the hub during setting link state is not enough, so let's disable LPM completely for this hub. Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200205112633.25995-3-kai.heng.feng@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2020-03-25 08:26:59 +01:00
Eugeniu Rosca	7b6f0567e2	usb: core: port: do error out if usb_autopm_get_interface() fails ... commit 1f8b39bc99 upstream. Reviewing a fresh portion of coverity defects in USB core (specifically CID 1458999), Alan Stern noted below in [1]: On Tue, Feb 25, 2020 at 02:39:23PM -0500, Alan Stern wrote: > A revised search finds line 997 in drivers/usb/core/hub.c and lines > 216, 269 in drivers/usb/core/port.c. (I didn't try looking in any > other directories.) AFAICT all three of these should check the > return value, although a error message in the kernel log probably > isn't needed. Factor out the usb_port_runtime_{resume,suspend}() changes into a standalone patch to allow conflict-free porting on top of stable v3.9+. [1] https://lore.kernel.org/lkml/Pine.LNX.4.44L0.2002251419120.1485-100000@iolanthe.rowland.org Fixes: 971fcd492c ("usb: add runtime pm support for usb port device") Cc: stable@vger.kernel.org # v3.9+ Suggested-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20200226175036.14946-3-erosca@de.adit-jv.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2020-03-12 07:18:32 +01:00
Eugeniu Rosca	e2f6344690	usb: core: hub: do error out if usb_autopm_get_interface() fails ... commit 60e3f6e4ac upstream. Reviewing a fresh portion of coverity defects in USB core (specifically CID 1458999), Alan Stern noted below in [1]: On Tue, Feb 25, 2020 at 02:39:23PM -0500, Alan Stern wrote: > A revised search finds line 997 in drivers/usb/core/hub.c and lines > 216, 269 in drivers/usb/core/port.c. (I didn't try looking in any > other directories.) AFAICT all three of these should check the > return value, although a error message in the kernel log probably > isn't needed. Factor out the usb_remove_device() change into a standalone patch to allow conflict-free integration on top of the earliest stable branches. [1] https://lore.kernel.org/lkml/Pine.LNX.4.44L0.2002251419120.1485-100000@iolanthe.rowland.org Fixes: 253e05724f ("USB: add a "remove hardware" sysfs attribute") Cc: stable@vger.kernel.org # v2.6.33+ Suggested-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20200226175036.14946-2-erosca@de.adit-jv.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2020-03-12 07:18:31 +01:00
Eugeniu Rosca	e2adfdd8a4	usb: core: hub: fix unhandled return by employing a void function ... commit 63d6d7ed47 upstream. Address below Coverity complaint (Feb 25, 2020, 8:06 AM CET):	2020-03-12 07:18:31 +01:00
Dan Lazewatsky	c80c82db09	usb: quirks: add NO_LPM quirk for Logitech Screen Share ... commit b96ed52d78 upstream. LPM on the device appears to cause xHCI host controllers to claim that there isn't enough bandwidth to support additional devices. Signed-off-by: Dan Lazewatsky <dlaz@chromium.org> Cc: stable <stable@vger.kernel.org> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com> Link: https://lore.kernel.org/r/20200226143438.1445-1-gustavo.padovan@collabora.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2020-03-12 07:18:31 +01:00
Hardik Gajjar	ee8a6e02d4	USB: hub: Fix the broken detection of USB3 device in SMSC hub ... commit 1208f9e1d7 upstream. Renesas R-Car H3ULCB + Kingfisher Infotainment Board is either not able to detect the USB3.0 mass storage devices or is detecting those as USB2.0 high speed devices. The explanation given by Renesas is that, due to a HW issue, the XHCI driver does not wake up after going to sleep on connecting a USB3.0 device. In order to mitigate that, disable the auto-suspend feature specifically for SMSC hubs from hub_probe() function, as a quirk. Renesas Kingfisher Infotainment Board has two USB3.0 ports (CN2) which are connected via USB5534B 4-port SuperSpeed/Hi-Speed, low-power, configurable hub controller. [1] SanDisk USB 3.0 device detected as USB-2.0 before the patch [ 74.036390] usb 5-1.1: new high-speed USB device number 4 using xhci-hcd [ 74.061598] usb 5-1.1: New USB device found, idVendor=0781, idProduct=5581, bcdDevice= 1.00 [ 74.069976] usb 5-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 74.077303] usb 5-1.1: Product: Ultra [ 74.080980] usb 5-1.1: Manufacturer: SanDisk [ 74.085263] usb 5-1.1: SerialNumber: 4C530001110208116550 [2] SanDisk USB 3.0 device detected as USB-3.0 after the patch [ 34.565078] usb 6-1.1: new SuperSpeed Gen 1 USB device number 3 using xhci-hcd [ 34.588719] usb 6-1.1: New USB device found, idVendor=0781, idProduct=5581, bcdDevice= 1.00 [ 34.597098] usb 6-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 34.604430] usb 6-1.1: Product: Ultra [ 34.608110] usb 6-1.1: Manufacturer: SanDisk [ 34.612397] usb 6-1.1: SerialNumber: 4C530001110208116550 Suggested-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Eugeniu Rosca <erosca@de.adit-jv.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/1580989763-32291-1-git-send-email-hgajjar@de.adit-jv.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2020-02-28 17:23:32 +01:00
Alan Stern	11e485d8f8	USB: hub: Don't record a connect-change event during reset-resume ... commit 8099f58f1e upstream. Paul Zimmerman reports that his USB Bluetooth adapter sometimes crashes following system resume, when it receives a Get-Device-Descriptor request while it is busy doing something else. Such a request was added by commit a4f55d8b8c ("usb: hub: Check device descriptor before resusciation"). It gets sent when the hub driver's work thread checks whether a connect-change event on an enabled port really indicates a new device has been connected, as opposed to an old device momentarily disconnecting and then reconnecting (which can happen with xHCI host controllers, since they automatically enable connected ports). The same kind of thing occurs when a port's power session is lost during system suspend. When the system wakes up it sees a connect-change event on the port, and if the child device's persist_enabled flag was set then hub_activate() sets the device's reset_resume flag as well as the port's bit in hub->change_bits. The reset-resume code then takes responsibility for checking that the same device is still attached to the port, and it does this as part of the device's resume pathway. By the time the hub driver's work thread starts up again, the device has already been fully reinitialized and is busy doing its own thing. There's no need for the work thread to do the same check a second time, and in fact this unnecessary check is what caused the problem that Paul observed. Note that performing the unnecessary check is not actually a bug. Devices are supposed to be able to send descriptors back to the host even when they are busy doing something else. The underlying cause of Paul's problem lies in his Bluetooth adapter. Nevertheless, we shouldn't perform the same check twice in a row -- and as a nice side benefit, removing the extra check allows the Bluetooth adapter to work more reliably. The work thread performs its check when it sees that the port's bit is set in hub->change_bits. In this situation that bit is interpreted as though a connect-change event had occurred on the port _after_ the reset-resume, which is not what actually happened. One possible fix would be to make the reset-resume code clear the port's bit in hub->change_bits. But it seems simpler to just avoid setting the bit during hub_activate() in the first place. That's what this patch does. (Proving that the patch is correct when CONFIG_PM is disabled requires a little thought. In that setting hub_activate() will be called only for initialization and resets, since there won't be any resumes or reset-resumes. During initialization and hub resets the hub doesn't have any child devices, and so this code path never gets executed.) Reported-and-tested-by: Paul Zimmerman <pauldzim@gmail.com> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Link: https://marc.info/?t=157949360700001&r=1&w=2 CC: David Heinzelmann <heinzelmann.david@gmail.com> CC: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2001311037460.1577-100000@iolanthe.rowland.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2020-02-28 17:23:32 +01:00
Richard Dodd	8cce7f36c3	USB: Fix novation SourceControl XL after suspend ... commit b692056db8 upstream. Currently, the SourceControl will stay in power-down mode after resuming from suspend. This patch resets the device after suspend to power it up. Signed-off-by: Richard Dodd <richard.o.dodd@gmail.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200212142220.36892-1-richard.o.dodd@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2020-02-28 17:23:32 +01:00
Johan Hovold	ac2c127174	USB: quirks: blacklist duplicate ep on Sound Devices USBPre2 ... commit bdd1b147b8 upstream. This device has a broken vendor-specific altsetting for interface 1, where endpoint 0x85 is declared as an isochronous endpoint despite being used by interface 2 for audio capture. Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 239 Miscellaneous Device bDeviceSubClass 2 bDeviceProtocol 1 Interface Association bMaxPacketSize0 64 idVendor 0x0926 idProduct 0x0202 bcdDevice 1.00 iManufacturer 1 Sound Devices iProduct 2 USBPre2 iSerial 3 [...] bNumConfigurations 1 [...] Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 3 bNumEndpoints 2 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 0 bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x85 EP 5 IN bmAttributes 5 Transfer Type Isochronous Synch Type Asynchronous Usage Type Data wMaxPacketSize 0x0126 1x 294 bytes bInterval 1 [...] Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 2 bAlternateSetting 1 bNumEndpoints 1 bInterfaceClass 1 Audio bInterfaceSubClass 2 Streaming bInterfaceProtocol 0 iInterface 0 AudioStreaming Interface Descriptor: bLength 7 bDescriptorType 36 bDescriptorSubtype 1 (AS_GENERAL) bTerminalLink 4 bDelay 1 frames wFormatTag 0x0001 PCM AudioStreaming Interface Descriptor: bLength 26 bDescriptorType 36 bDescriptorSubtype 2 (FORMAT_TYPE) bFormatType 1 (FORMAT_TYPE_I) bNrChannels 2 bSubframeSize 2 bBitResolution 16 bSamFreqType 6 Discrete tSamFreq[ 0] 8000 tSamFreq[ 1] 16000 tSamFreq[ 2] 24000 tSamFreq[ 3] 32000 tSamFreq[ 4] 44100 tSamFreq[ 5] 48000 Endpoint Descriptor: bLength 9 bDescriptorType 5 bEndpointAddress 0x85 EP 5 IN bmAttributes 5 Transfer Type Isochronous Synch Type Asynchronous Usage Type Data wMaxPacketSize 0x0126 1x 294 bytes bInterval 4 bRefresh 0 bSynchAddress 0 AudioStreaming Endpoint Descriptor: bLength 7 bDescriptorType 37 bDescriptorSubtype 1 (EP_GENERAL) bmAttributes 0x01 Sampling Frequency bLockDelayUnits 2 Decoded PCM samples wLockDelay 0x0000 Since commit 3e4f8e21c4 ("USB: core: fix check for duplicate endpoints") USB core ignores any duplicate endpoints found during descriptor parsing, but in this case we need to ignore the first instance in order to avoid breaking the audio capture interface. Fixes: 3e4f8e21c4 ("USB: core: fix check for duplicate endpoints") Cc: stable <stable@vger.kernel.org> Reported-by: edes <edes@gmx.net> Tested-by: edes <edes@gmx.net> Link: https://lore.kernel.org/r/20200201105829.5682c887@acme7.acmenet Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20200203153830.26394-3-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2020-02-28 17:23:32 +01:00
Johan Hovold	0e8fb84c5c	USB: core: add endpoint-blacklist quirk ... commit 73f8bda9b5 upstream. Add a new device quirk that can be used to blacklist endpoints. Since commit 3e4f8e21c4 ("USB: core: fix check for duplicate endpoints") USB core ignores any duplicate endpoints found during descriptor parsing. In order to handle devices where the first interfaces with duplicate endpoints are the ones that should have their endpoints ignored, we need to add a blacklist. Tested-by: edes <edes@gmx.net> Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20200203153830.26394-2-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2020-02-28 17:23:31 +01:00
Keiya Nobuta	9c06ac4c83	usb: core: hub: Improved device recognition on remote wakeup ... If hub_activate() is called before D+ has stabilized after remote wakeup, the following situation might occur: __ ___________________ / \ / D+ __/ \__/ Hub _______________________________ | ^ ^ ^ | | | | Host _____v__|___|___________|______ | | | | | | | \-- Interrupt Transfer (*3) | | \-- ClearPortFeature (*2) | \-- GetPortStatus (*1) \-- Host detects remote wakeup - D+ goes high, Host starts running by remote wakeup - D+ is not stable, goes low - Host requests GetPortStatus at (*1) and gets the following hub status: - Current Connect Status bit is 0 - Connect Status Change bit is 1 - D+ stabilizes, goes high - Host requests ClearPortFeature and thus Connect Status Change bit is cleared at (*2) - After waiting 100 ms, Host starts the Interrupt Transfer at (*3) - Since the Connect Status Change bit is 0, Hub returns NAK. In this case, port_event() is not called in hub_event() and Host cannot recognize device. To solve this issue, flag change_bits even if only Connect Status Change bit is 1 when got in the first GetPortStatus. This issue occurs rarely because it only if D+ changes during a very short time between GetPortStatus and ClearPortFeature. However, it is fatal if it occurs in embedded system. Signed-off-by: Keiya Nobuta <nobuta.keiya@fujitsu.com> Cc: stable <stable@vger.kernel.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20200109051448.28150-1-nobuta.keiya@fujitsu.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2020-01-15 13:14:28 +01:00
Qi Zhou	1530f6f5f5	usb: missing parentheses in USE_NEW_SCHEME ... According to bd0e6c9614 ("usb: hub: try old enumeration scheme first for high speed devices") the kernel will try the old enumeration scheme first for high speed devices. This can happen when a high speed device is plugged in. But due to missing parentheses in the USE_NEW_SCHEME define, this logic can get messed up and the incorrect result happens. Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Qi Zhou <atmgnd@outlook.com> Link: https://lore.kernel.org/r/ht4mtag8ZP-HKEhD0KkJhcFnVlOFV8N8eNjJVRD9pDkkLUNhmEo8_cL_sl7xy9mdajdH-T8J3TFQsjvoYQT61NFjQXy469Ed_BbBw_x4S1E=@protonmail.com [ fixup changelog text - gregkh] Cc: stable <stable@vger.kernel.org> Fixes: bd0e6c9614 ("usb: hub: try old enumeration scheme first for high speed devices") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2020-01-08 17:44:11 +01:00
Alan Stern	2548288b4f	USB: Fix: Don't skip endpoint descriptors with maxpacket=0 ... It turns out that even though endpoints with a maxpacket length of 0 aren't useful for data transfer, the descriptors do serve other purposes. In particular, skipping them will also skip over other class-specific descriptors for classes such as UVC. This unexpected side effect has caused some UVC cameras to stop working. In addition, the USB spec requires that when isochronous endpoint descriptors are present in an interface's altsetting 0 (which is true on some devices), the maxpacket size _must_ be set to 0. Warning about such things seems like a bad idea. This patch updates an earlier commit which would log a warning and skip these endpoint descriptors. Now we only log a warning, and we don't even do that for isochronous endpoints in altsetting 0. We don't need to worry about preventing endpoints with maxpacket = 0 from ever being used for data transfers; usb_submit_urb() already checks for this. Reported-and-tested-by: Roger Whittaker <Roger.Whittaker@suse.com> Fixes: d482c7bb05 ("USB: Skip endpoints with 0 maxpacket length") Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Link: https://marc.info/?l=linux-usb&m=157790377329882&w=2 Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2001061040270.1514-100000@iolanthe.rowland.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2020-01-06 16:54:09 +01:00
Johan Hovold	3e4f8e21c4	USB: core: fix check for duplicate endpoints ... Amend the endpoint-descriptor sanity checks to detect all duplicate endpoint addresses in a configuration. Commit 0a8fd13462 ("USB: fix problems with duplicate endpoint addresses") added a check for duplicate endpoint addresses within a single alternate setting, but did not look for duplicate addresses in other interfaces. The current check would also not detect all duplicate addresses when one endpoint is as a (bi-directional) control endpoint. This specifically avoids overwriting the endpoint entries in struct usb_device when enabling a duplicate endpoint, something which could potentially lead to crashes or leaks, for example, when endpoints are later disabled. Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20191219161016.6695-1-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2019-12-30 19:54:55 +01:00
Fredrik Noring	f8c63edfd7	USB: Fix incorrect DMA allocations for local memory pool drivers ... Fix commit 7b81cb6bdd ("usb: add a HCD_DMA flag instead of guestimating DMA capabilities") where local memory USB drivers erroneously allocate DMA memory instead of pool memory, causing OHCI Unrecoverable Error, disabled HC died; cleaning up The order between hcd_uses_dma() and hcd->localmem_pool is now arranged as in hcd_buffer_alloc() and hcd_buffer_free(), with the test for hcd->localmem_pool placed first. As an alternative, one might consider adjusting hcd_uses_dma() with static inline bool hcd_uses_dma(struct usb_hcd *hcd) { - return IS_ENABLED(CONFIG_HAS_DMA) && (hcd->driver->flags & HCD_DMA); + return IS_ENABLED(CONFIG_HAS_DMA) && + (hcd->driver->flags & HCD_DMA) && + (hcd->localmem_pool == NULL); } One can also consider unsetting HCD_DMA for local memory pool drivers. Fixes: 7b81cb6bdd ("usb: add a HCD_DMA flag instead of guestimating DMA capabilities") Cc: stable <stable@vger.kernel.org> Signed-off-by: Fredrik Noring <noring@nocrew.org> Link: https://lore.kernel.org/r/20191210172905.GA52526@sx9 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2019-12-11 09:06:41 +01:00
Emiliano Ingrassia	1cd17f7f0d	usb: core: urb: fix URB structure initialization function ... Explicitly initialize URB structure urb_list field in usb_init_urb(). This field can be potentially accessed uninitialized and its initialization is coherent with the usage of list_del_init() in usb_hcd_unlink_urb_from_ep() and usb_giveback_urb_bh() and its explicit initialization in usb_hcd_submit_urb() error path. Signed-off-by: Emiliano Ingrassia <ingrassia@epigenesys.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191127160355.GA27196@ingrassia.epigenesys.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2019-12-10 11:41:19 +01:00
Andrey Konovalov	95d23dc27b	usb, kcov: collect coverage from hub_event ... Add kcov_remote_start()/kcov_remote_stop() annotations to the hub_event() function, which is responsible for processing events on USB buses, in particular events that happen during USB device enumeration. Since hub_event() is run in a global background kernel thread (see Documentation/dev-tools/kcov.rst for details), each USB bus gets a unique global handle from the USB subsystem kcov handle range. As the result kcov can now be used to collect coverage from events that happen on a particular USB bus. [akpm@linux-foundation.org: avoid patch conflicts to make life easier for Andrew] Link: http://lkml.kernel.org/r/de4fe1c219db2d002d905dc1736e2a3bfa1db997.1572366574.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Alexander Potapenko <glider@google.com> Cc: Anders Roxell <anders.roxell@linaro.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: David Windsor <dwindsor@gmail.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Elena Reshetova <elena.reshetova@intel.com> Cc: Jason Wang <jasowang@redhat.com> Cc: Marco Elver <elver@google.com> Cc: "Michael S. Tsirkin" <mst@redhat.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>	2019-12-04 19:44:14 -08:00
Linus Torvalds	c3bed3b20e	Merge tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci ... Pull PCI updates from Bjorn Helgaas: "Enumeration: - Warn if a host bridge has no NUMA info (Yunsheng Lin) - Add PCI_STD_NUM_BARS for the number of standard BARs (Denis Efremov) Resource management: - Fix boot-time Embedded Controller GPE storm caused by incorrect resource assignment after ACPI Bus Check Notification (Mika Westerberg) - Protect pci_reassign_bridge_resources() against concurrent addition/removal (Benjamin Herrenschmidt) - Fix bridge dma_ranges resource list cleanup (Rob Herring) - Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control the MMIO and prefetchable MMIO window sizes of hotplug bridges independently (Nicholas Johnson) - Fix MMIO/MMIO_PREF window assignment that assigned more space than desired (Nicholas Johnson) - Only enforce bus numbers from bridge EA if the bridge has EA devices downstream (Subbaraya Sundeep) - Consolidate DT "dma-ranges" parsing and convert all host drivers to use shared parsing (Rob Herring) Error reporting: - Restore AER capability after resume (Mayurkumar Patel) - Add PoisonTLPBlocked AER counter (Rajat Jain) - Use for_each_set_bit() to simplify AER code (Andy Shevchenko) - Fix AER kernel-doc (Andy Shevchenko) - Add "pcie_ports=dpc-native" parameter to allow native use of DPC even if platform didn't grant control over AER (Olof Johansson) Hotplug: - Avoid returning prematurely from sysfs requests to enable or disable a PCIe hotplug slot (Lukas Wunner) - Don't disable interrupts twice when suspending hotplug ports (Mika Westerberg) - Fix deadlocks when PCIe ports are hot-removed while suspended (Mika Westerberg) Power management: - Remove unnecessary ASPM locking (Bjorn Helgaas) - Add support for disabling L1 PM Substates (Heiner Kallweit) - Allow re-enabling Clock PM after it has been disabled (Heiner Kallweit) - Add sysfs attributes for controlling ASPM link states (Heiner Kallweit) - Remove CONFIG_PCIEASPM_DEBUG, including "link_state" and "clk_ctl" sysfs files (Heiner Kallweit) - Avoid AMD FCH XHCI USB PME# from D0 defect that prevents wakeup on USB 2.0 or 1.1 connect events (Kai-Heng Feng) - Move power state check out of pci_msi_supported() (Bjorn Helgaas) - Fix incorrect MSI-X masking on resume and revert related nvme quirk for Kingston NVME SSD running FW E8FK11.T (Jian-Hong Pan) - Always return devices to D0 when thawing to fix hibernation with drivers like mlx4 that used legacy power management (previously we only did it for drivers with new power management ops) (Dexuan Cui) - Clear PCIe PME Status even for legacy power management (Bjorn Helgaas) - Fix PCI PM documentation errors (Bjorn Helgaas) - Use dev_printk() for more power management messages (Bjorn Helgaas) - Apply D2 delay as milliseconds, not microseconds (Bjorn Helgaas) - Convert xen-platform from legacy to generic power management (Bjorn Helgaas) - Removed unused .resume_early() and .suspend_late() legacy power management hooks (Bjorn Helgaas) - Rearrange power management code for clarity (Rafael J. Wysocki) - Decode power states more clearly ("4" or "D4" really refers to "D3cold") (Bjorn Helgaas) - Notice when reading PM Control register returns an error (~0) instead of interpreting it as being in D3hot (Bjorn Helgaas) - Add missing link delays required by the PCIe spec (Mika Westerberg) Virtualization: - Move pci_prg_resp_pasid_required() to CONFIG_PCI_PRI (Bjorn Helgaas) - Allow VFs to use PRI (the PF PRI is shared by the VFs, but the code previously didn't recognize that) (Kuppuswamy Sathyanarayanan) - Allow VFs to use PASID (the PF PASID capability is shared by the VFs, but the code previously didn't recognize that) (Kuppuswamy Sathyanarayanan) - Disconnect PF and VF ATS enablement, since ATS in PFs and associated VFs can be enabled independently (Kuppuswamy Sathyanarayanan) - Cache PRI and PASID capability offsets (Kuppuswamy Sathyanarayanan) - Cache the PRI PRG Response PASID Required bit (Bjorn Helgaas) - Consolidate ATS declarations in linux/pci-ats.h (Krzysztof Wilczynski) - Remove unused PRI and PASID stubs (Bjorn Helgaas) - Removed unnecessary EXPORT_SYMBOL_GPL() from ATS, PRI, and PASID interfaces that are only used by built-in IOMMU drivers (Bjorn Helgaas) - Hide PRI and PASID state restoration functions used only inside the PCI core (Bjorn Helgaas) - Add a DMA alias quirk for the Intel VCA NTB (Slawomir Pawlowski) - Serialize sysfs sriov_numvfs reads vs writes (Pierre Crégut) - Update Cavium ACS quirk for ThunderX2 and ThunderX3 (George Cherian) - Fix the UPDCR register address in the Intel ACS quirk (Steffen Liebergeld) - Unify ACS quirk implementations (Bjorn Helgaas) Amlogic Meson host bridge driver: - Fix meson PERST# GPIO polarity problem (Remi Pommarel) - Add DT bindings for Amlogic Meson G12A (Neil Armstrong) - Fix meson clock names to match DT bindings (Neil Armstrong) - Add meson support for Amlogic G12A SoC with separate shared PHY (Neil Armstrong) - Add meson extended PCIe PHY functions for Amlogic G12A USB3+PCIe combo PHY (Neil Armstrong) - Add arm64 DT for Amlogic G12A PCIe controller node (Neil Armstrong) - Add commented-out description of VIM3 USB3/PCIe mux in arm64 DT (Neil Armstrong) Broadcom iProc host bridge driver: - Invalidate iProc PAXB address mapping before programming it (Abhishek Shah) - Fix iproc-msi and mvebu __iomem annotations (Ben Dooks) Cadence host bridge driver: - Refactor Cadence PCIe host controller to use as a library for both host and endpoint (Tom Joseph) Freescale Layerscape host bridge driver: - Add layerscape LS1028a support (Xiaowei Bao) Intel VMD host bridge driver: - Add VMD bus 224-255 restriction decode (Jon Derrick) - Add VMD 8086:9A0B device ID (Jon Derrick) - Remove Keith from VMD maintainer list (Keith Busch) Marvell ARMADA 3700 / Aardvark host bridge driver: - Use LTSSM state to build link training flag since Aardvark doesn't implement the Link Training bit (Remi Pommarel) - Delay before training Aardvark link in case PERST# was asserted before the driver probe (Remi Pommarel) - Fix Aardvark issues with Root Control reads and writes (Remi Pommarel) - Don't rely on jiffies in Aardvark config access path since interrupts may be disabled (Remi Pommarel) - Fix Aardvark big-endian support (Grzegorz Jaszczyk) Marvell ARMADA 370 / XP host bridge driver: - Make mvebu_pci_bridge_emul_ops static (Ben Dooks) Microsoft Hyper-V host bridge driver: - Add hibernation support for Hyper-V virtual PCI devices (Dexuan Cui) - Track Hyper-V pci_protocol_version per-hbus, not globally (Dexuan Cui) - Avoid kmemleak false positive on hv hbus buffer (Dexuan Cui) Mobiveil host bridge driver: - Change mobiveil csr_read()/write() function names that conflict with riscv arch functions (Kefeng Wang) NVIDIA Tegra host bridge driver: - Fix Tegra CLKREQ dependency programming (Vidya Sagar) Renesas R-Car host bridge driver: - Remove unnecessary header include from rcar (Andrew Murray) - Tighten register index checking for rcar inbound range programming (Marek Vasut) - Fix rcar inbound range alignment calculation to improve packing of multiple entries (Marek Vasut) - Update rcar MACCTLR setting to match documentation (Yoshihiro Shimoda) - Clear bit 0 of MACCTLR before PCIETCTLR.CFINIT per manual (Yoshihiro Shimoda) - Add Marek Vasut and Yoshihiro Shimoda as R-Car maintainers (Simon Horman) Rockchip host bridge driver: - Make rockchip 0V9 and 1V8 power regulators non-optional (Robin Murphy) Socionext UniPhier host bridge driver: - Set uniphier to host (RC) mode always (Kunihiko Hayashi) Endpoint drivers: - Fix endpoint driver sign extension problem when shifting page number to phys_addr_t (Alan Mikhak) Misc: - Add NumaChip SPDX header (Krzysztof Wilczynski) - Replace EXTRA_CFLAGS with ccflags-y (Krzysztof Wilczynski) - Remove unused includes (Krzysztof Wilczynski) - Removed unused sysfs attribute groups (Ben Dooks) - Remove PTM and ASPM dependencies on PCIEPORTBUS (Bjorn Helgaas) - Add PCIe Link Control 2 register field definitions to replace magic numbers in AMDGPU and Radeon CIK/SI (Bjorn Helgaas) - Fix incorrect Link Control 2 Transmit Margin usage in AMDGPU and Radeon CIK/SI PCIe Gen3 link training (Bjorn Helgaas) - Use pcie_capability_read_word() instead of pci_read_config_word() in AMDGPU and Radeon CIK/SI (Frederick Lawler) - Remove unused pci_irq_get_node() Greg Kroah-Hartman) - Make asm/msi.h mandatory and simplify PCI_MSI_IRQ_DOMAIN Kconfig (Palmer Dabbelt, Michal Simek) - Read all 64 bits of Switchtec part_event_bitmap (Logan Gunthorpe) - Fix erroneous intel-iommu dependency on CONFIG_AMD_IOMMU (Bjorn Helgaas) - Fix bridge emulation big-endian support (Grzegorz Jaszczyk) - Fix dwc find_next_bit() usage (Niklas Cassel) - Fix pcitest.c fd leak (Hewenliang) - Fix typos and comments (Bjorn Helgaas) - Fix Kconfig whitespace errors (Krzysztof Kozlowski)" * tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (160 commits) PCI: Remove PCI_MSI_IRQ_DOMAIN architecture whitelist asm-generic: Make msi.h a mandatory include/asm header Revert "nvme: Add quirk for Kingston NVME SSD running FW E8FK11.T" PCI/MSI: Fix incorrect MSI-X masking on resume PCI/MSI: Move power state check out of pci_msi_supported() PCI/MSI: Remove unused pci_irq_get_node() PCI: hv: Avoid a kmemleak false positive caused by the hbus buffer PCI: hv: Change pci_protocol_version to per-hbus PCI: hv: Add hibernation support PCI: hv: Reorganize the code in preparation of hibernation MAINTAINERS: Remove Keith from VMD maintainer PCI/ASPM: Remove PCIEASPM_DEBUG Kconfig option and related code PCI/ASPM: Add sysfs attributes for controlling ASPM link states PCI: Fix indentation drm/radeon: Prefer pcie_capability_read_word() drm/radeon: Replace numbers with PCI_EXP_LNKCTL2 definitions drm/radeon: Correct Transmit Margin masks drm/amdgpu: Prefer pcie_capability_read_word() PCI: uniphier: Set mode register to host mode drm/amdgpu: Replace numbers with PCI_EXP_LNKCTL2 definitions ...	2019-12-03 13:58:22 -08:00
Linus Torvalds	0da522107e	Merge tag 'compat-ioctl-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground ... Pull removal of most of fs/compat_ioctl.c from Arnd Bergmann: "As part of the cleanup of some remaining y2038 issues, I came to fs/compat_ioctl.c, which still has a couple of commands that need support for time64_t. In completely unrelated work, I spent time on cleaning up parts of this file in the past, moving things out into drivers instead. After Al Viro reviewed an earlier version of this series and did a lot more of that cleanup, I decided to try to completely eliminate the rest of it and move it all into drivers. This series incorporates some of Al's work and many patches of my own, but in the end stops short of actually removing the last part, which is the scsi ioctl handlers. I have patches for those as well, but they need more testing or possibly a rewrite" * tag 'compat-ioctl-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground: (42 commits) scsi: sd: enable compat ioctls for sed-opal pktcdvd: add compat_ioctl handler compat_ioctl: move SG_GET_REQUEST_TABLE handling compat_ioctl: ppp: move simple commands into ppp_generic.c compat_ioctl: handle PPPIOCGIDLE for 64-bit time_t compat_ioctl: move PPPIOCSCOMPRESS to ppp_generic compat_ioctl: unify copy-in of ppp filters tty: handle compat PPP ioctls compat_ioctl: move SIOCOUTQ out of compat_ioctl.c compat_ioctl: handle SIOCOUTQNSD af_unix: add compat_ioctl support compat_ioctl: reimplement SG_IO handling compat_ioctl: move WDIOC handling into wdt drivers fs: compat_ioctl: move FITRIM emulation into file systems gfs2: add compat_ioctl support compat_ioctl: remove unused convert_in_user macro compat_ioctl: remove last RAID handling code compat_ioctl: remove /dev/raw ioctl translation compat_ioctl: remove PCI ioctl translation compat_ioctl: remove joystick ioctl translation ...	2019-12-01 13:46:15 -08:00
Linus Torvalds	81b6b96475	Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux; tag 'dma-mapping-5.5' of git://git.infradead.org/users/hch/dma-mapping ... Pull dma-mapping updates from Christoph Hellwig: - improve dma-debug scalability (Eric Dumazet) - tiny dma-debug cleanup (Dan Carpenter) - check for vmap memory in dma_map_single (Kees Cook) - check for dma_addr_t overflows in dma-direct when using DMA offsets (Nicolas Saenz Julienne) - switch the x86 sta2x11 SOC to use more generic DMA code (Nicolas Saenz Julienne) - fix arm-nommu dma-ranges handling (Vladimir Murzin) - use __initdata in CMA (Shyam Saini) - replace the bus dma mask with a limit (Nicolas Saenz Julienne) - merge the remapping helpers into the main dma-direct flow (me) - switch xtensa to the generic dma remap handling (me) - various cleanups around dma_capable (me) - remove unused dev arguments to various dma-noncoherent helpers (me) * 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux: * tag 'dma-mapping-5.5' of git://git.infradead.org/users/hch/dma-mapping: (22 commits) dma-mapping: treat dev->bus_dma_mask as a DMA limit dma-direct: exclude dma_direct_map_resource from the min_low_pfn check dma-direct: don't check swiotlb=force in dma_direct_map_resource dma-debug: clean up put_hash_bucket() powerpc: remove support for NULL dev in __phys_to_dma / __dma_to_phys dma-direct: avoid a forward declaration for phys_to_dma dma-direct: unify the dma_capable definitions dma-mapping: drop the dev argument to arch_sync_dma_for_* x86/PCI: sta2x11: use default DMA address translation dma-direct: check for overflows on 32 bit DMA addresses dma-debug: increase HASH_SIZE dma-debug: reorder struct dma_debug_entry fields xtensa: use the generic uncached segment support dma-mapping: merge the generic remapping helpers into dma-direct dma-direct: provide mmap and get_sgtable method overrides dma-direct: remove the dma_handle argument to __dma_direct_alloc_pages dma-direct: remove __dma_direct_free_pages usb: core: Remove redundant vmap checks kernel: dma-contiguous: mark CMA parameters __initdata/__initconst dma-debug: add a schedule point in debug_dma_dump_mappings() ...	2019-11-28 11:16:43 -08:00
Kai-Heng Feng	e76b3bf765	usb: Allow USB device to be warm reset in suspended state ... On Dell WD15 dock, sometimes USB ethernet cannot be detected after plugging cable to the ethernet port, the hub and roothub get runtime resumed and runtime suspended immediately: ... [ 433.315169] xhci_hcd 0000:3a:00.0: hcd_pci_runtime_resume: 0 [ 433.315204] usb usb4: usb auto-resume [ 433.315226] hub 4-0:1.0: hub_resume [ 433.315239] xhci_hcd 0000:3a:00.0: Get port status 4-1 read: 0x10202e2, return 0x10343 [ 433.315264] usb usb4-port1: status 0343 change 0001 [ 433.315279] xhci_hcd 0000:3a:00.0: clear port1 connect change, portsc: 0x10002e2 [ 433.315293] xhci_hcd 0000:3a:00.0: Get port status 4-2 read: 0x2a0, return 0x2a0 [ 433.317012] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling. [ 433.422282] xhci_hcd 0000:3a:00.0: Get port status 4-1 read: 0x10002e2, return 0x343 [ 433.422307] usb usb4-port1: do warm reset [ 433.422311] usb 4-1: device reset not allowed in state 8 [ 433.422339] hub 4-0:1.0: state 7 ports 2 chg 0002 evt 0000 [ 433.422346] xhci_hcd 0000:3a:00.0: Get port status 4-1 read: 0x10002e2, return 0x343 [ 433.422356] usb usb4-port1: do warm reset [ 433.422358] usb 4-1: device reset not allowed in state 8 [ 433.422428] xhci_hcd 0000:3a:00.0: set port remote wake mask, actual port 0 status = 0xf0002e2 [ 433.422455] xhci_hcd 0000:3a:00.0: set port remote wake mask, actual port 1 status = 0xe0002a0 [ 433.422465] hub 4-0:1.0: hub_suspend [ 433.422475] usb usb4: bus auto-suspend, wakeup 1 [ 433.426161] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling. [ 433.466209] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.510204] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.554051] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.598235] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.642154] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.686204] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.730205] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.774203] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.818207] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.862040] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.862053] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling. [ 433.862077] xhci_hcd 0000:3a:00.0: xhci_suspend: stopping port polling. [ 433.862096] xhci_hcd 0000:3a:00.0: // Setting command ring address to 0x8578fc001 [ 433.862312] xhci_hcd 0000:3a:00.0: hcd_pci_runtime_suspend: 0 [ 433.862445] xhci_hcd 0000:3a:00.0: PME# enabled [ 433.902376] xhci_hcd 0000:3a:00.0: restoring config space at offset 0xc (was 0x0, writing 0x20) [ 433.902395] xhci_hcd 0000:3a:00.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100403) [ 433.902490] xhci_hcd 0000:3a:00.0: PME# disabled [ 433.902504] xhci_hcd 0000:3a:00.0: enabling bus mastering [ 433.902547] xhci_hcd 0000:3a:00.0: // Setting command ring address to 0x8578fc001 [ 433.902649] pcieport 0000:00:1b.0: PME: Spurious native interrupt! [ 433.902839] xhci_hcd 0000:3a:00.0: Port change event, 4-1, id 3, portsc: 0xb0202e2 [ 433.902842] xhci_hcd 0000:3a:00.0: resume root hub [ 433.902845] xhci_hcd 0000:3a:00.0: handle_port_status: starting port polling. [ 433.902877] xhci_hcd 0000:3a:00.0: xhci_resume: starting port polling. [ 433.902889] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling. [ 433.902891] xhci_hcd 0000:3a:00.0: hcd_pci_runtime_resume: 0 [ 433.902919] usb usb4: usb wakeup-resume [ 433.902942] usb usb4: usb auto-resume [ 433.902966] hub 4-0:1.0: hub_resume ... As Mathias pointed out, the hub enters Cold Attach Status state and requires a warm reset. However usb_reset_device() bails out early when the device is in suspended state, as its callers port_event() and hub_event() don't always resume the device. Since there's nothing wrong to reset a suspended device, allow usb_reset_device() to do so to solve the issue. Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191106062710.29880-1-kai.heng.feng@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2019-11-07 11:14:51 +01:00
Greg Kroah-Hartman	16c8373ecf	Merge 5.4-rc6 into usb-next ... We need the USB fixes in here to build on top of. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2019-11-04 06:41:09 +01:00
Kees Cook	b3d53f5fce	usb: core: Remove redundant vmap checks ... Now that the vmap area checks are being performed in the DMA infrastructure directly, there is no need to repeat them in USB. Signed-off-by: Kees Cook <keescook@chromium.org> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Christoph Hellwig <hch@lst.de>	2019-10-31 06:40:43 -07:00
Alan Stern	d482c7bb05	USB: Skip endpoints with 0 maxpacket length ... Endpoints with a maxpacket length of 0 are probably useless. They can't transfer any data, and it's not at all unlikely that an HCD will crash or hang when trying to handle an URB for such an endpoint. Currently the USB core does not check for endpoints having a maxpacket value of 0. This patch adds a check, printing a warning and skipping over any endpoints it catches. Now, the USB spec does not rule out endpoints having maxpacket = 0. But since they wouldn't have any practical use, there doesn't seem to be any good reason for us to accept them. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1910281050420.1485-100000@iolanthe.rowland.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2019-10-28 17:46:22 +01:00
Arnd Bergmann	407e9ef724	compat_ioctl: move drivers to compat_ptr_ioctl ... Each of these drivers has a copy of the same trivial helper function to convert the pointer argument and then call the native ioctl handler. We now have a generic implementation of that, so use it. Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: David S. Miller <davem@davemloft.net> Acked-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Reviewed-by: Jason Gunthorpe <jgg@mellanox.com> Reviewed-by: Jiri Kosina <jkosina@suse.cz> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Reviewed-by: Cornelia Huck <cohuck@redhat.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>	2019-10-23 17:23:43 +02:00
Ingo Rohloff	abb0b3d96a	usb: usbfs: Suppress problematic bind and unbind uevents. ... commit 1455cf8dbf ("driver core: emit uevents when device is bound to a driver") added bind and unbind uevents when a driver is bound or unbound to a physical device. For USB devices which are handled via the generic usbfs layer (via libusb for example), this is problematic: Each time a user space program calls ioctl(usb_fd, USBDEVFS_CLAIMINTERFACE, &usb_intf_nr); and then later ioctl(usb_fd, USBDEVFS_RELEASEINTERFACE, &usb_intf_nr); The kernel will now produce a bind or unbind event, which does not really contain any useful information. This allows a user space program to run a DoS attack against programs which listen to uevents (in particular systemd/eudev/upowerd): A malicious user space program just has to call in a tight loop ioctl(usb_fd, USBDEVFS_CLAIMINTERFACE, &usb_intf_nr); ioctl(usb_fd, USBDEVFS_RELEASEINTERFACE, &usb_intf_nr); With this loop the malicious user space program floods the kernel and all programs listening to uevents with tons of bind and unbind events. This patch suppresses uevents for ioctls USBDEVFS_CLAIMINTERFACE and USBDEVFS_RELEASEINTERFACE. Signed-off-by: Ingo Rohloff <ingo.rohloff@lauterbach.com> Link: https://lore.kernel.org/r/20191011115518.2801-1-ingo.rohloff@lauterbach.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2019-10-15 20:22:13 +02:00
Denis Efremov	c9c13ba428	PCI: Add PCI_STD_NUM_BARS for the number of standard BARs ... Code that iterates over all standard PCI BARs typically uses PCI_STD_RESOURCE_END. However, that requires the unusual test "i <= PCI_STD_RESOURCE_END" rather than something the typical "i < PCI_STD_NUM_BARS". Add a definition for PCI_STD_NUM_BARS and change loops to use the more idiomatic C style to help avoid fencepost errors. Link: https://lore.kernel.org/r/20190927234026.23342-1-efremov@linux.com Link: https://lore.kernel.org/r/20190927234308.23935-1-efremov@linux.com Link: https://lore.kernel.org/r/20190916204158.6889-3-efremov@linux.com Signed-off-by: Denis Efremov <efremov@linux.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Sebastian Ott <sebott@linux.ibm.com> # arch/s390/ Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> # video/fbdev/ Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com> # pci/controller/dwc/ Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com> # scsi/pm8001/ Acked-by: Martin K. Petersen <martin.petersen@oracle.com> # scsi/pm8001/ Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # memstick/	2019-10-14 10:22:26 -05:00
Saurav Girepunje	71464db9c2	usb: core: devio.c: Fix assignment of 0/1 to bool variables ... Use true/false for is_in bool type in function proc_do_submiturb. Signed-off-by: Saurav Girepunje <saurav.girepunje@gmail.com> Link: https://lore.kernel.org/r/20191007182649.GA7068@saurav Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2019-10-10 12:34:07 +02:00
Johan Hovold	dd2057e544	USB: core: drop OOM message ... Drop redundant OOM message on allocation failures which would already have been logged by the allocator. This also allows us to clean up the error paths somewhat. Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20191008090240.30376-1-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2019-10-10 12:34:07 +02:00
David Heinzelmann	a4f55d8b8c	usb: hub: Check device descriptor before resusciation ... If a device connected to an xHCI host controller disconnects from the USB bus and then reconnects, e.g. triggered by a firmware update, then the host controller automatically activates the connection and the port is enabled. The implementation of hub_port_connect_change() assumes that if the port is enabled then nothing has changed. There is no check if the USB descriptors have changed. As a result, the kernel's internal copy of the descriptors ends up being incorrect and the device doesn't work properly anymore. The solution to the problem is for hub_port_connect_change() always to check whether the device's descriptors have changed before resuscitating an enabled port. Signed-off-by: David Heinzelmann <heinzelmann.david@gmail.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20191009044647.24536-1-heinzelmann.david@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2019-10-10 12:34:06 +02:00
Alan Stern	3dd550a2d3	USB: usbcore: Fix slab-out-of-bounds bug during device reset ... The syzbot fuzzer provoked a slab-out-of-bounds error in the USB core: BUG: KASAN: slab-out-of-bounds in memcmp+0xa6/0xb0 lib/string.c:904 Read of size 1 at addr ffff8881d175bed6 by task kworker/0:3/2746 CPU: 0 PID: 2746 Comm: kworker/0:3 Not tainted 5.3.0-rc5+ #28 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Workqueue: usb_hub_wq hub_event Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0xca/0x13e lib/dump_stack.c:113 print_address_description+0x6a/0x32c mm/kasan/report.c:351 __kasan_report.cold+0x1a/0x33 mm/kasan/report.c:482 kasan_report+0xe/0x12 mm/kasan/common.c:612 memcmp+0xa6/0xb0 lib/string.c:904 memcmp include/linux/string.h:400 [inline] descriptors_changed drivers/usb/core/hub.c:5579 [inline] usb_reset_and_verify_device+0x564/0x1300 drivers/usb/core/hub.c:5729 usb_reset_device+0x4c1/0x920 drivers/usb/core/hub.c:5898 rt2x00usb_probe+0x53/0x7af drivers/net/wireless/ralink/rt2x00/rt2x00usb.c:806 The error occurs when the descriptors_changed() routine (called during a device reset) attempts to compare the old and new BOS and capability descriptors. The length it uses for the comparison is the wTotalLength value stored in BOS descriptor, but this value is not necessarily the same as the length actually allocated for the descriptors. If it is larger the routine will call memcmp() with a length that is too big, thus reading beyond the end of the allocated region and leading to this fault. The kernel reads the BOS descriptor twice: first to get the total length of all the capability descriptors, and second to read it along with all those other descriptors. A malicious (or very faulty) device may send different values for the BOS descriptor fields each time. The memory area will be allocated using the wTotalLength value read the first time, but stored within it will be the value read the second time. To prevent this possibility from causing any errors, this patch modifies the BOS descriptor after it has been read the second time: It sets the wTotalLength field to the actual length of the descriptors that were read in and validated. Then the memcpy() call, or any other code using these descriptors, will be able to rely on wTotalLength being valid. Reported-and-tested-by: syzbot+35f4d916c623118d576e@syzkaller.appspotmail.com Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1909041154260.1722-100000@iolanthe.rowland.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2019-09-04 18:24:00 +02:00
Greg Kroah-Hartman	c5c0283a9d	Merge generic_lookup_helpers into usb-next ... The lookup helpers are needed here. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2019-09-03 17:11:07 +02:00
Marek Szyprowski	34c7ed72f4	usb: core: phy: add support for PHY calibration ... Some PHYs (for example Exynos5 USB3.0 DRD PHY) require calibration to be done after every USB HCD reset. Generic PHY framework has been already extended with phy_calibrate() function in commit 36914111e6 ("drivers: phy: add calibrate method"). This patch adds support for it to generic PHY handling code in USB HCD core. Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by: Anand Moon <linux.amoon@gmail.com> Tested-by: Jochen Sprickerhof <jochen@sprickerhof.de> Link: https://lore.kernel.org/r/20190829053028.32438-2-m.szyprowski@samsung.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2019-09-03 15:54:55 +02:00
Christoph Hellwig	7b65fe1255	usb: remove commented out dma wrappers ... These wrappers have never seen use and have been commented out for a long time. Remove them for good. Signed-off-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20190903084615.19161-6-hch@lst.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2019-09-03 15:26:12 +02:00
Christoph Hellwig	ac2658e0d9	usb: remove a stale comment in hcd_alloc_coherent ... Now that we have the local memory pool implemented there is no need to use dma_declare_coherent_memory. Signed-off-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20190903084615.19161-5-hch@lst.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2019-09-03 15:26:11 +02:00
Greg Kroah-Hartman	7a81146204	Merge 5.3-rc7 into usb-next ... We need the usb fixes in here for testing Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2019-09-02 19:31:18 +02:00
Schmid, Carsten	76da906ad7	usb: hcd: use managed device resources ... Using managed device resources in usb_hcd_pci_probe() allows devm usage for resource subranges, such as the mmio resource for the platform device created to control host/device mode mux, which is a xhci extended capability, and sits inside the xhci mmio region. If managed device resources are not used then "parent" resource is released before subrange at driver removal as .remove callback is called before the devres list of resources for this device is walked and released. This has been observed with the xhci extended capability driver causing a use-after-free which is now fixed. An additional nice benefit is that error handling on driver initialisation is simplified much. Signed-off-by: Carsten Schmid <carsten_schmid@mentor.com> Tested-by: Carsten Schmid <carsten_schmid@mentor.com> Reviewed-by: Mathias Nyman <mathias.nyman@linux.intel.com> Fixes: fa31b3cb2a ("xhci: Add Intel extended cap / otg phy mux handling") Cc: <stable@vger.kernel.org> # v4.19+ Link: https://lore.kernel.org/r/1566569488679.31808@mentor.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2019-08-28 22:48:37 +02:00
Christoph Hellwig	7b81cb6bdd	usb: add a HCD_DMA flag instead of guestimating DMA capabilities ... The usb core is the only major place in the kernel that checks for a non-NULL device dma_mask to see if a device is DMA capable. This is generally a bad idea, as all major busses always set up a DMA mask, even if the device is not DMA capable - in fact bus layers like PCI can't even know if a device is DMA capable at enumeration time. This leads to lots of workaround in HCD drivers, and also prevented us from setting up a DMA mask for platform devices by default last time we tried. Replace this guess with an explicit HCD_DMA that is set by drivers that appear to have DMA support. Signed-off-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20190816062435.881-4-hch@lst.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2019-08-21 10:03:35 -07:00
Gavin Li	b08a6259a1	usb: usbfs: only account once for mmap()'ed usb memory usage ... Memory usage for USB memory allocated via mmap() is already accounted for at mmap() time; no need to account for it again at submiturb time. Signed-off-by: Gavin Li <git@thegavinli.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20190814212924.10381-1-gavinli@thegavinli.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2019-08-21 09:57:36 -07:00
Greg Kroah-Hartman	7ffc95e90e	Merge 5.3-rc5 into usb-next ... We need the usb fixes in here as well for other patches to build on. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2019-08-19 07:15:42 +02:00
Christoph Hellwig	edfbcb321f	usb: add a hcd_uses_dma helper ... The USB buffer allocation code is the only place in the usb core (and in fact the whole kernel) that uses is_device_dma_capable, while the URB mapping code uses the uses_dma flag in struct usb_bus. Switch the buffer allocation to use the uses_dma flag used by the rest of the USB code, and create a helper in hcd.h that checks this flag as well as the CONFIG_HAS_DMA to simplify the caller a bit. Signed-off-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20190811080520.21712-3-hch@lst.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2019-08-15 15:18:05 +02:00
Christoph Hellwig	dd3ecf17ba	usb: don't create dma pools for HCDs with a localmem_pool ... If the HCD provides a localmem pool we will never use the DMA pools, so don't create them. Fixes: b0310c2f09 ("USB: use genalloc for USB HCs with local memory") Signed-off-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20190811080520.21712-2-hch@lst.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2019-08-15 15:17:07 +02:00
Oliver Neukum	54364278fb	USB: CDC: fix sanity checks in CDC union parser ... A few checks checked for the size of the pointer to a structure instead of the structure itself. Copy & paste issue presumably. Fixes: e4c6fb7794 ("usbnet: move the CDC parser into USB core") Cc: stable <stable@vger.kernel.org> Reported-by: syzbot+45a53506b65321c1fe91@syzkaller.appspotmail.com Signed-off-by: Oliver Neukum <oneukum@suse.com> Link: https://lore.kernel.org/r/20190813093541.18889-1-oneukum@suse.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2019-08-15 14:49:16 +02:00
Alan Stern	4ed3350539	USB: usbfs: Add a capability flag for runtime suspend ... The recent commit 7794f486ed ("usbfs: Add ioctls for runtime power management") neglected to add a corresponding capability flag. This patch rectifies the omission. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Mayuresh Kulkarni <mkulkarni@opensource.cirrus.com> Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1908131613490.1941-100000@iolanthe.rowland.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2019-08-14 16:52:13 +02:00
Alan Stern	303911cfc5	USB: core: Fix races in character device registration and deregistraion ... The syzbot fuzzer has found two (!) races in the USB character device registration and deregistration routines. This patch fixes the races. The first race results from the fact that usb_deregister_dev() sets usb_minors[intf->minor] to NULL before calling device_destroy() on the class device. This leaves a window during which another thread can allocate the same minor number but will encounter a duplicate name error when it tries to register its own class device. A typical error message in the system log would look like: sysfs: cannot create duplicate filename '/class/usbmisc/ldusb0' The patch fixes this race by destroying the class device first. The second race is in usb_register_dev(). When that routine runs, it first allocates a minor number, then drops minor_rwsem, and then creates the class device. If the device creation fails, the minor number is deallocated and the whole routine returns an error. But during the time while minor_rwsem was dropped, there is a window in which the minor number is allocated and so another thread can successfully open the device file. Typically this results in use-after-free errors or invalid accesses when the other thread closes its open file reference, because the kernel then tries to release resources that were already deallocated when usb_register_dev() failed. The patch fixes this race by keeping minor_rwsem locked throughout the entire routine. Reported-and-tested-by: syzbot+30cf45ebfe0b0c4847a1@syzkaller.appspotmail.com Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1908121607590.1659-100000@iolanthe.rowland.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2019-08-12 22:47:24 +02:00
Greg Kroah-Hartman	51fa228c8e	Merge 5.3-rc4 into usb-next ... We need the USB fixes in here as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2019-08-12 07:42:51 +02:00
Alan Stern	7794f486ed	usbfs: Add ioctls for runtime power management ... It has been requested that usbfs should implement runtime power management, instead of forcing the device to remain at full power as long as the device file is open. This patch introduces that new feature. It does so by adding three new usbfs ioctls: USBDEVFS_FORBID_SUSPEND: Prevents the device from going into runtime suspend (and causes a resume if the device is already suspended). USBDEVFS_ALLOW_SUSPEND: Allows the device to go into runtime suspend. Some time may elapse before the device actually is suspended, depending on things like the autosuspend delay. USBDEVFS_WAIT_FOR_RESUME: Blocks until the call is interrupted by a signal or at least one runtime resume has occurred since the most recent ALLOW_SUSPEND ioctl call (which may mean immediately, even if the device is currently suspended). In the latter case, the device is prevented from suspending again just as if FORBID_SUSPEND was called before the ioctl returns. For backward compatibility, when the device file is first opened runtime suspends are forbidden. The userspace program can then allow suspends whenever it wants, and either resume the device directly (by forbidding suspends again) or wait for a resume from some other source (such as a remote wakeup). URBs submitted to a suspended device will fail or will complete with an appropriate error code. This combination of ioctls is sufficient for user programs to have nearly the same degree of control over a device's runtime power behavior as kernel drivers do. Still lacking is documentation for the new ioctls. I intend to add it later, after the existing documentation for the usbfs userspace API is straightened out into a reasonable form. Suggested-by: Mayuresh Kulkarni <mkulkarni@opensource.cirrus.com> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1908071013220.1514-100000@iolanthe.rowland.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>	2019-08-09 07:55:45 +02:00