[ Upstream commit e4bf63482c ]
Most, if not all, Quectel devices use dynamic interface numbers, and
users are able to change the USB configuration at will. Matching on for
example interface number is therefore not possible.
Instead, the QMI device can be identified by looking at the interface
class, subclass and protocol (all 0xff), as well as the number of
endpoints. The reason we need to look at the number of endpoints, is
that the diagnostic port interface has the same class, subclass and
protocol as QMI. However, the diagnostic port only has two endpoints,
while QMI has three.
Until now, we have identified the QMI device by combining a match on
class, subclass and protocol, with a call to the function
quectel_diag_detect(). In quectel_diag_detect(), we check if the number
of endpoints matches for known Quectel vendor/product ids.
Adding new vendor/product ids to quectel_diag_detect() is not a good
long-term solution. This commit replaces the function with a quirk, and
applies the quirk to affected Quectel devices that I have been able to
test the change with (EP06, EM12 and EC25). If the quirk is set and the
number of endpoints equal two, we return from qmi_wwan_probe() with
-ENODEV.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfb0ebed53 ]
Modifying the VLAN stripping options when a port VLAN is configured
will break traffic for the VSI, and conceptually doesn't make sense,
so don't allow this.
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06b6e2a233 ]
This patch fixes the problem with the driver being able to add only 7
multicast MAC address filters instead of 16. The problem is fixed by
changing the maximum number of MAC address filters to 16+1+1 (two extra
are needed because the driver uses 1 for unicast MAC address and 1 for
broadcast).
Signed-off-by: Adam Ludkiewicz <adam.ludkiewicz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ed2a00534 ]
In case create_singlethread_workqueue fails, the fix free the
hardware and returns NULL to avoid NULL pointer dereference.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5414c2355 ]
kmalloc can fail in rsi_register_rates_channels but memcpy still attempts
to write to channels. The patch replaces these calls with kmemdup and
passes the error upstream.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4c35c1722 ]
The "rate_index" is only used as an index into the phist_data->rx_rate[]
array in the mwifiex_hist_data_set() function. That array has
MWIFIEX_MAX_AC_RX_RATES (74) elements and it's used to generate some
debugfs information. The "rate_index" variable comes from the network
skb->data[] and it is a u8 so it's in the 0-255 range. We need to cap
it to prevent an array overflow.
Fixes: cbf6e05527 ("mwifiex: add rx histogram statistics support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30f24eabab ]
If for some reason the device gives us an RX interrupt before we're
ready for it, perhaps during device power-on with misconfigured IRQ
causes mapping or so, we can crash trying to access the queues.
Prevent that by checking that we actually have RXQs and that they
were properly allocated.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e025da3d7a ]
If "ret_len" is negative then it could lead to a NULL dereference.
The "ret_len" value comes from nl80211_vendor_cmd(), if it's negative
then we don't allocate the "dcmd_buf" buffer. Then we pass "ret_len" to
brcmf_fil_cmd_data_set() where it is cast to a very high u32 value.
Most of the functions in that call tree check whether the buffer we pass
is NULL but there are at least a couple places which don't such as
brcmf_dbg_hex_dump() and brcmf_msgbuf_query_dcmd(). We memcpy() to and
from the buffer so it would result in a NULL dereference.
The fix is to change the types so that "ret_len" can't be negative. (If
we memcpy() zero bytes to NULL, that's a no-op and doesn't cause an
issue).
Fixes: 1bacb0487d ("brcmfmac: replace cfg80211 testmode with vendor command")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93aa4792c3 ]
When the ring buffer is almost full due to RX completion messages, a
TX packet may reach the "low watermark" and cause the queue stopped.
If the TX completion arrives earlier than queue stopping, the wakeup
may be missed.
This patch moves the check for the last pending packet to cover both
EAGAIN and success cases, so the queue will be reliably waked up when
necessary.
Reported-and-tested-by: Stephan Klein <stephan.klein@wegfinder.at>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f913308879 ]
GCC 8 contains a number of new warnings as well as enhancements to existing
checkers. The warning - Wstringop-truncation - warns for calls to bounded
string manipulation functions such as strncat, strncpy, and stpncpy that
may either truncate the copied string or leave the destination unchanged.
In our case the destination string length (32 bytes) is much shorter than
the source string (64 bytes) which causes this warning to show up. In
general the destination has to be at least a byte larger than the length
of the source string with strncpy for this warning not to showup.
This can be easily fixed by using strlcpy instead which already does the
truncation to the string. Documentation for this function can be
found here:
https://elixir.bootlin.com/linux/latest/source/lib/string.c#L141
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de1887c064 ]
We don't check for the validity of the lengths in the packet received
from the firmware. If the MPDU length received in the rx descriptor
is too short to contain the header length and the crypt length
together, we may end up trying to copy a negative number of bytes
(headlen - hdrlen < 0) which will underflow and cause us to try to
copy a huge amount of data. This causes oopses such as this one:
BUG: unable to handle kernel paging request at ffff896be2970000
PGD 5e201067 P4D 5e201067 PUD 5e205067 PMD 16110d063 PTE 8000000162970161
Oops: 0003 [#1] PREEMPT SMP NOPTI
CPU: 2 PID: 1824 Comm: irq/134-iwlwifi Not tainted 4.19.33-04308-geea41cf4930f #1
Hardware name: [...]
RIP: 0010:memcpy_erms+0x6/0x10
Code: 90 90 90 90 eb 1e 0f 1f 00 48 89 f8 48 89 d1 48 c1 e9 03 83 e2 07 f3 48 a5 89 d1 f3 a4 c3 66 0f 1f 44 00 00 48 89 f8 48 89 d1 <f3> a4 c3
0f 1f 80 00 00 00 00 48 89 f8 48 83 fa 20 72 7e 40 38 fe
RSP: 0018:ffffa4630196fc60 EFLAGS: 00010287
RAX: ffff896be2924618 RBX: ffff896bc8ecc600 RCX: 00000000fffb4610
RDX: 00000000fffffff8 RSI: ffff896a835e2a38 RDI: ffff896be2970000
RBP: ffffa4630196fd30 R08: ffff896bc8ecc600 R09: ffff896a83597000
R10: ffff896bd6998400 R11: 000000000200407f R12: ffff896a83597050
R13: 00000000fffffff8 R14: 0000000000000010 R15: ffff896a83597038
FS: 0000000000000000(0000) GS:ffff896be8280000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffff896be2970000 CR3: 000000005dc12002 CR4: 00000000003606e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
iwl_mvm_rx_mpdu_mq+0xb51/0x121b [iwlmvm]
iwl_pcie_rx_handle+0x58c/0xa89 [iwlwifi]
iwl_pcie_irq_rx_msix_handler+0xd9/0x12a [iwlwifi]
irq_thread_fn+0x24/0x49
irq_thread+0xb0/0x122
kthread+0x138/0x140
ret_from_fork+0x1f/0x40
Fix that by checking the lengths for correctness and trigger a warning
to show that we have received wrong data.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 22e8860cf8 ]
regmap_update_bits could fail and deserves a check.
The patch adds the checks and if it fails, returns its error
code upstream.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f0916c6dc ]
ethtool user spaces needs to know ring count via ETHTOOL_GRXRINGS when
executing (ethtool -x) which is retrieved via ethtool get_rxnfc callback,
in mlx5 this callback is disabled when CONFIG_MLX5_EN_RXNFC=n.
This patch allows only ETHTOOL_GRXRINGS command on mlx5e_get_rxnfc() when
CONFIG_MLX5_EN_RXNFC is disabled, so ethtool -x will continue working.
Fixes: fe6d86b3c3 ("net/mlx5e: Add CONFIG_MLX5_EN_RXNFC for ethtool rx nfc")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bad861f31b ]
mlxfw can be compiled as external module while mlx5_core can be
builtin, in such case mlx5 will act like mlxfw is disabled.
Since mlxfw is just a service library for mlx* drivers,
imply it in mlx5_core to make it always reachable if it was enabled.
Fixes: 3ffaabecd1 ("net/mlx5e: Support the flash device ethtool callback")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0fe9f173d6 ]
Jiri reported that with a kernel built with CONFIG_FIXED_PHY=y,
CONFIG_NET_DSA=m and CONFIG_NET_DSA_LOOP=m, we would not get to a
functional state where the mock-up driver is registered. Turns out that
we are not descending into drivers/net/dsa/ unconditionally, and we
won't be able to link-in dsa_loop_bdinfo.o which does the actual mock-up
mdio device registration.
Reported-by: Jiri Pirko <jiri@resnulli.us>
Fixes: 40013ff20b ("net: dsa: Fix functional dsa-loop dependency on FIXED_PHY")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Tested-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9871a9e47a ]
When a queue(tfile) is detached through __tun_detach(), we move the
last enabled tfile to the position where detached one sit but don't
NULL out last position. We expect to synchronize the datapath through
tun->numqueues. Unfortunately, this won't work since we're lacking
sufficient mechanism to order or synchronize the access to
tun->numqueues.
To fix this, NULL out the last position during detaching and check
RCU protected tfile against NULL instead of checking tun->numqueues in
datapath.
Cc: YueHaibing <yuehaibing@huawei.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: weiyongjun (A) <weiyongjun1@huawei.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Fixes: c8d68e6be1 ("tuntap: multiqueue support")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a35d310f03 ]
We need check if tun->numqueues is zero (e.g for the persist device)
before trying to use it for modular arithmetic.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Fixes: 96f84061620c6("tun: add eBPF based queue selection method")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5afcd14cfc ]
The old MIPS implementation of dma_cache_sync() didn't use the dev argument,
but commit c9eb6172c3 ("dma-mapping: turn dma_cache_sync into a
dma_map_ops method") changed that, so we now need to set dev.parent.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0504453139 ]
Current order in open:
-> Enable interrupts (macb_init_hw)
-> Enable NAPI
-> Start PHY
Sequence of RX handling:
-> RX interrupt occurs
-> Interrupt is cleared and interrupt bits disabled in handler
-> NAPI is scheduled
-> In NAPI, RX budget is processed and RX interrupts are re-enabled
With the above, on QEMU or fixed link setups (where PHY state doesn't
matter), there's a chance macb RX interrupt occurs before NAPI is
enabled. This will result in NAPI being scheduled before it is enabled.
Fix this macb open by changing the order.
Fixes: ae1f2a56d2 ("net: macb: Added support for many RX queues")
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d4c26eb6e7 ]
When adding more MAC addresses to a dwmac-sun8i interface, the device goes
directly in promiscuous mode.
This is due to IFF_UNICAST_FLT missing flag.
So since the hardware support unicast filtering, let's add IFF_UNICAST_FLT.
Fixes: 9f93ac8d40 ("net-next: stmmac: Add dwmac-sun8i")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 17170e6570 ]
Fix issue with the entry indexing in the sg frame cleanup code being
off-by-1. This problem showed up when doing some basic iperf tests and
manifested in traffic coming to a halt.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Acked-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a9b8a2b39c ]
There's currently a problem with toggling arp_validate on and off with an
active-backup bond. At the moment, you can start up a bond, like so:
modprobe bonding mode=1 arp_interval=100 arp_validate=0 arp_ip_targets=192.168.1.1
ip link set bond0 down
echo "ens4f0" > /sys/class/net/bond0/bonding/slaves
echo "ens4f1" > /sys/class/net/bond0/bonding/slaves
ip link set bond0 up
ip addr add 192.168.1.2/24 dev bond0
Pings to 192.168.1.1 work just fine. Now turn on arp_validate:
echo 1 > /sys/class/net/bond0/bonding/arp_validate
Pings to 192.168.1.1 continue to work just fine. Now when you go to turn
arp_validate off again, the link falls flat on it's face:
echo 0 > /sys/class/net/bond0/bonding/arp_validate
dmesg
...
[133191.911987] bond0: Setting arp_validate to none (0)
[133194.257793] bond0: bond_should_notify_peers: slave ens4f0
[133194.258031] bond0: link status definitely down for interface ens4f0, disabling it
[133194.259000] bond0: making interface ens4f1 the new active one
[133197.330130] bond0: link status definitely down for interface ens4f1, disabling it
[133197.331191] bond0: now running without any active interface!
The problem lies in bond_options.c, where passing in arp_validate=0
results in bond->recv_probe getting set to NULL. This flies directly in
the face of commit 3fe68df97c, which says we need to set recv_probe =
bond_arp_recv, even if we're not using arp_validate. Said commit fixed
this in bond_option_arp_interval_set, but missed that we can get to that
same state in bond_option_arp_validate_set as well.
One solution would be to universally set recv_probe = bond_arp_recv here
as well, but I don't think bond_option_arp_validate_set has any business
touching recv_probe at all, and that should be left to the arp_interval
code, so we can just make things much tidier here.
Fixes: 3fe68df97c ("bonding: always set recv_probe to bond_arp_rcv in arp monitor")
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84242b82d8 upstream.
Add missing break statement in order to prevent the code from falling
through to case 0x1025, and erroneously setting rtlhal->oem_id to
RT_CID_819X_ACER when rtlefuse->eeprom_svid is equal to 0x10EC and
none of the cases in switch (rtlefuse->eeprom_smid) match.
This bug was found thanks to the ongoing efforts to enable
-Wimplicit-fallthrough.
Fixes: 238ad2ddf3 ("rtlwifi: rtl8723ae: Clean up the hardware info routine")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b583201fa upstream.
It was reported on OpenWrt bug tracking system[1], that several users
are affected by the endless reboot of their routers if they configure
5GHz interface with channel 44 or 48.
The reboot loop is caused by the following excessive number of WARN_ON
messages:
WARNING: CPU: 0 PID: 0 at backports-4.19.23-1/net/mac80211/rx.c:4516
ieee80211_rx_napi+0x1fc/0xa54 [mac80211]
as the messages are being correctly emitted by the following guard:
case RX_ENC_LEGACY:
if (WARN_ON(status->rate_idx >= sband->n_bitrates))
as the rate_idx is in this case erroneously set to 251 (0xfb). This fix
simply converts previously used magic number to proper constant and
guards against substraction which is leading to the currently observed
underflow.
1. https://bugs.openwrt.org/index.php?do=details&task_id=2218
Fixes: 854783444b ("mwl8k: properly set receive status rate index on 5 GHz receive")
Cc: <stable@vger.kernel.org>
Tested-by: Eubert Bao <bunnier@gmail.com>
Reported-by: Eubert Bao <bunnier@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b442fed1b7 ]
The workqueue is used to periodically update the networking stack about
activity / statistics of various objects such as neighbours and TC
actions.
It should not be called as part of memory reclaim path, so remove the
WQ_MEM_RECLAIM flag.
Fixes: 3d5479e920 ("mlxsw: core: Remove deprecated create_workqueue")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
[ Upstream commit a8c133b061 ]
The EMAD workqueue is used to handle retransmission of EMAD packets that
contain configuration data for the device's firmware.
Given the workers need to allocate these packets and that the code is
not called as part of memory reclaim path, remove the WQ_MEM_RECLAIM
flag.
Fixes: d965465b60 ("mlxsw: core: Fix possible deadlock")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
[ Upstream commit d7c3a206e6 ]
Some SOC like i.MX6SX clock have some limits:
- ahb clock should be disabled before ipg.
- ahb and ipg clocks are required for MAC MII bus.
So, move the ahb clock to runtime management together with
ipg clock.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
[ Upstream commit 5ceaeb99ff ]
This patches fixes few issues in mv88e6390x_port_set_cmode().
1. When entering the function the old cmode may be 0, in this case
mv88e6390x_serdes_get_lane() returns -ENODEV. As result we bail
out and have no chance to set a new mode. Therefore deal properly
with -ENODEV.
2. Once we have disabled power and irq, let's set the cached cmode to 0.
This reflects the actual status and is cleaner if we bail out with an
error in the following function calls.
3. The cached cmode is used by mv88e6390x_serdes_get_lane(),
mv88e6390_serdes_power_lane() and mv88e6390_serdes_irq_enable().
Currently we set the cached mode to the new one at the very end of
the function only, means until then we use the old one what may be
wrong.
4. When calling mv88e6390_serdes_irq_enable() we use the lane value
belonging to the old cmode. Get the lane belonging to the new cmode
before calling this function.
It's hard to provide a good "Fixes" tag because quite a few smaller
changes have been done to the code in question recently.
Fixes: d235c48b40 ("net: dsa: mv88e6xxx: power serdes on/off for 10G interfaces on 6390X")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
[ Upstream commit 2f23a2a768 ]
Add missing <of_device_id> table for SPI driver relying on SPI
device match since compatible is in a DT binding or in a DTS.
Before this patch:
modinfo drivers/net/phy/spi_ks8995.ko | grep alias
alias: spi:ksz8795
alias: spi:ksz8864
alias: spi:ks8995
After this patch:
modinfo drivers/net/phy/spi_ks8995.ko | grep alias
alias: spi:ksz8795
alias: spi:ksz8864
alias: spi:ks8995
alias: of:N*T*Cmicrel,ksz8795C*
alias: of:N*T*Cmicrel,ksz8795
alias: of:N*T*Cmicrel,ksz8864C*
alias: of:N*T*Cmicrel,ksz8864
alias: of:N*T*Cmicrel,ks8995C*
alias: of:N*T*Cmicrel,ks8995
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Daniel Gomez <dagmcr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1dc2b3d655 ]
The err2 error return path calls qede_ptp_disable that cleans up
on an error and frees ptp. After this, the free'd ptp is dereferenced
when ptp->clock is set to NULL and the code falls-through to error
path err1 that frees ptp again.
Fix this by calling qede_ptp_disable and exiting via an error
return path that does not set ptp->clock or kfree ptp.
Addresses-Coverity: ("Write to pointer after free")
Fixes: 035744975a ("qede: Add support for PTP resource locking.")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a2c34f18c ]
Currently if a pci dma mapping failure is detected a free'd
memblock address is returned rather than a NULL (that indicates
an error). Fix this by ensuring NULL is returned on this error case.
Addresses-Coverity: ("Use after free")
Fixes: 528f727279 ("vxge: code cleanup and reorganization")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f87db4dbd5 upstream.
gcc warn this:
drivers/net/ethernet/stmicro/stmmac/norm_desc.c: In function ndesc_init_rx_desc:
drivers/net/ethernet/stmicro/stmmac/norm_desc.c:138:6: warning: variable 'bfsize1' set but not used [-Wunused-but-set-variable]
Like enh_desc_init_rx_desc, we should use bfsize1
in ndesc_init_rx_desc to calculate 'p->des1'
Fixes: 583e636141 ("net: stmmac: use correct DMA buffer size in the RX descriptor")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cc5a726c79 ]
BITS_TO_LONGS() uses DIV_ROUND_UP() because of
this ppmax value can be greater than available
per cpu page pods.
This patch removes BITS_TO_LONGS() to fix this
issue.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f058e46855 ]
ICMP6 neighbor solicitation messages will be discard by the Hip06
chips, because of not setting forwarding pool. Enable promisc mode
has the same problem.
This patch fix the wrong forwarding table configs for the multicast
vague matching when enable promisc mode, and add forwarding pool
for the forwarding table.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
