Allowing these GDSCs to collapse makes the QMP combo PHYs lose their
configuration on machine suspend. Currently, the QMP combo PHY driver
doesn't reinitialise the HW on resume. Under such conditions, the USB
SuperSpeed support is broken. To avoid this, mark the pwrsts flags with
RET_ON. This is in line with USB 2 PHY GDSC config.
Fixes: 161b7c401f ("clk: qcom: Add Global Clock controller (GCC) driver for X1E80100")
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240801-x1e80100-clk-gcc-fix-usb-phy-gdscs-pwrsts-v1-1-8df016768a0f@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
In case of all pipe clocks, there is a QMP PHY clock that is feeding them.
If, for whatever reason, the clock from the PHY is not enabled, halt bit
will not get set, and the clock controller driver will assume the clock
is stuck in a specific state. The way this is supposed to be properly
fixed is to defer the checking of the halt bit until after the PHY clock
has been initialized, but doing so complicates the clock controller
driver. In fact, since these pipe clocks are consumed by the PHY, while
the PHY is also the one providing the source, if clock gets stuck, the PHY
driver would be to blame. So instead of checking the halt bit in here,
just skip it and assume the PHY driver is handling the source clock
correctly.
Fixes: 161b7c401f ("clk: qcom: Add Global Clock controller (GCC) driver for X1E80100")
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Taniya Das <quic_tdas@quicinc.com>
Link: https://lore.kernel.org/r/20240628-x1e80100-clk-gcc-fix-halt-check-for-usb-phy-pipe-clks-v2-1-db3be54b1143@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The previous wrapper qcom_cc_really_probe takes the platform
device as parameter, which is limited to platform driver.
As for qca8k clock controller driver, which is registered as
the MDIO device, which also follows the qcom clock framework.
To commonize qcom_cc_really_probe, updating it to take the
struct device as parameter, so that the qcom_cc_really_probe
can be utilized by the previous platform device and the new
added MDIO device.
Also update the current clock controller drivers to take
&pdev->dev as parameter when calling qcom_cc_really_probe.
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Link: https://lore.kernel.org/r/20240605124541.2711467-4-quic_luoj@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h.
of_device.h isn't needed, but mod_devicetable.h and platform_device.h
were implicitly included.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Sibi Sankar <quic_sibis@quicinc.com>
Link: https://lore.kernel.org/r/20231211160510.0aef871b@canb.auug.org.au
[robh: Redo commit msg]
Signed-off-by: Rob Herring <robh@kernel.org>
