These chips needs the same fix. This was previously not seen
on then since the AGP aperture expanded the system aperture,
but this showed up again when AGP was disabled.
Reviewed-and-tested-by: Jiadong Zhu <Jiadong.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the below smatch warnings:
drivers/gpu/drm/amd/amdgpu/amdgpu_ras.c:2543 amdgpu_ras_recovery_init() warn: Please consider using kzalloc instead of kmalloc
drivers/gpu/drm/amd/amdgpu/amdgpu_ras.c:2830 amdgpu_ras_init() warn: Please consider using kzalloc instead of kmalloc
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's required to take the gfx mutex before access to CP_VMID_RESET,
for there is a race condition with CP firmware to write the register.
v2: add extra code to ensure the mutex releasing is successful.
Signed-off-by: Jack Xiao <Jack.Xiao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Change the rules for amdgpu_sync_resv to let KFD synchronize with VM
fences on page table reservations. This fixes intermittent memory
corruption after evictions when using amdgpu_vm_handle_moved to update
page tables for VM mappings managed through render nodes.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The ecc_irq is disabled while GPU mode2 reset suspending process,
but not be enabled during GPU mode2 reset resume process.
Changed from V1:
only do sdma/gfx ras_late_init in aldebaran_mode2_restore_ip
delete amdgpu_ras_late_resume function
Changed from V2:
check umc ras supported before put ecc_irq
Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Updates for v6.8:
Core:
- Add support for SDM670, SM8650
- Handle the CFG interconnect to fix the obscure hangs / timeouts
on register write
- Kconfig fix for QMP dependency
- DT schema fixes
DPU:
- Add support for SDM670, SM8650
- Enable SmartDMA on SM8350 and SM8450
- Correct UBWC settings for SC8280XP
- Fix catalog settings for SC8180X
- Actually make use of the version to switch between QSEED3/3LITE/4
scalers
- Use devres-managed and drm-managed allocations where appropriate
- misc other fixes
- Enabled YUV writeback on SC7280, SM8250
- Enabled writeback on SM8350, SM8450
- CRC fix when encoder is selected as the input source
- other misc fixes
MDP4:
- Use devres-managed and drm-managed allocations where appropriate
- flush vblank event on CRTC disable
MDP5:
- Use devres-managed and drm-managed allocations where appropriate
DP:
- Add support for SM8650
- Enable PM runtime support
- Merge msm-specific debugfs dir with the generic one
- Described DisplayPort on SM8150 in DeviceTree bindings
- Moved dp_display_get_next_bridge() to probe()
DSI:
- Add support for SM8650
- Enable PM runtime support
GPU/GEM:
- demote userspace triggerable warnings to debug
- add GEM object metadata UAPI
- move GPU devcoredumps to GPU device
- fix hangcheck to skip retired submits
- expose UBWC config to userspace
- fix a680 chip-id
- drm_exec conversion
- drm/ci: remove rebase-merge directory (to unblock CI)
[airlied: fix drm_exec/amd interaction]
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGs9auYqmo-7NSd9FsbNBCDf7aBevd=4xkcF3A5G_OGvMQ@mail.gmail.com
Idle bo's PTE needs to be re-created when resetting VM state machine.
Set idle bo's vm_bo as moved to mark it as invalid.
Fixes: 55bf196f60 ("drm/amdgpu: reset VM when an error is detected")
Signed-off-by: ZhenGuo Yin <zhenguo.yin@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When application tries to allocate all system memory and cause memory
to swap out. Needs more time for hmm_range_fault to validate the
remaining page for allocation. To be safe, increase timeout value to
1 second for 64MB range.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Plane CTM for pre-blending color space conversion. Only enable
driver-specific plane CTM property on drivers that support both pre- and
post-blending gamut remap matrix, i.e., DCN3+ family. Otherwise it
conflits with DRM CRTC CTM property.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Issue: during evict or validate happened on amdgpu_bo, the 'from' and
'to' is always same in ftrace event of amdgpu_bo_move
where calling the 'trace_amdgpu_bo_move', the comment says move_notify
is called before move happens, but actually it is called after move
happens, here the new_mem is same as bo->resource
Fix: move trace_amdgpu_bo_move from move_notify to amdgpu_bo_move
Signed-off-by: Wang, Beyond <Wang.Beyond@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Including drm_edid.h from amdgpu_mode.h causes the rebuild of literally
hundreds of files when drm_edid.h is modified, while there are only a
handful of files that actually need to include drm_edid.h.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add AMD pre-defined transfer function property to default DRM CRTC gamma
to convert to wire encoding with or without a user gamma LUT. There is
no post-blending regamma ROM for pre-defined TF. When setting Gamma TF
(!= Identity) and LUT at the same time, the color module will combine
the pre-defined TF and the custom LUT values into the LUT that's
actually programmed.
v2:
- enable CRTC prop in the end of driver-specific prop sequence
- define inverse EOTFs as supported regamma TFs
- reword driver-specific function doc to remove shaper/3D LUT
v3:
- spell out TF+LUT behavior in the commit and comments (Harry)
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Co-developed-by: Joshua Ashton <joshua@froggi.es>
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Blend 1D LUT or a pre-defined transfer function (TF) can be set to
linearize content before blending, so that it's positioned just before
blending planes in the AMD color mgmt pipeline, and after 3D LUT
(non-linear space). Shaper and Blend LUTs are 1D LUTs that sandwich 3D
LUT. Drivers should advertize blend properties according to HW caps.
There is no blend ROM for pre-defined TF. When setting blend TF (!=
Identity) and LUT at the same time, the color module will combine the
pre-defined TF and the custom LUT values into the LUT that's actually
programmed.
v3:
- spell out TF+LUT behavior in the commit and comments (Harry)
v5:
- get blend blob correctly
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On AMD HW, 3D LUT always assumes a preceding shaper 1D LUT used for
delinearizing and/or normalizing the color space before applying a 3D
LUT. Add pre-defined transfer function to enable delinearizing content
with or without shaper LUT, where AMD color module calculates the
resulted shaper curve. We apply an inverse EOTF to go from linear
values to encoded values. If we are already in a non-linear space and/or
don't need to normalize values, we can bypass shaper LUT with a linear
transfer function that is also the default TF value.
There is no shaper ROM. When setting shaper TF (!= Identity) and LUT at
the same time, the color module will combine the pre-defined TF and the
custom LUT values into the LUT that's actually programmed.
v2:
- squash commits for shaper LUT and shaper TF
- define inverse EOTF as supported shaper TFs
v3:
- spell out TF+LUT behavior in the commit and comments (Harry)
- replace BT709 EOTF by inv OETF
v5:
- get shaper blob correctly (Joshua)
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
MES provides the driver a call to explicitly flush stale process memory
within the MES to avoid a race condition that results in a fatal
memory violation.
When SET_SHADER_DEBUGGER is called, the driver passes a memory address
that represents a process context address MES uses to keep track of
future per-process calls.
Normally, MES will purge its process context list when the last queue
has been removed. The driver, however, can call SET_SHADER_DEBUGGER
regardless of whether a queue has been added or not.
If SET_SHADER_DEBUGGER has been called with no queues as the last call
prior to process termination, the passed process context address will
still reside within MES.
On a new process call to SET_SHADER_DEBUGGER, the driver may end up
passing an identical process context address value (based on per-process
gpu memory address) to MES but is now pointing to a new allocated buffer
object during KFD process creation. Since the MES is unaware of this,
access of the passed address points to the stale object within MES and
triggers a fatal memory violation.
The solution is for KFD to explicitly flush the process context address
from MES on process termination.
Note that the flush call and the MES debugger calls use the same MES
interface but are separated as KFD calls to avoid conflicting with each
other.
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com>
Tested-by: Alice Wong <shiwei.wong@amd.com>
Reviewed-by: Eric Huang <jinhuieric.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
commit 751e293f2c ("drm/amd: Move microcode init from sw_init to
early_init for SDMA v2.4") made a fateful mistake in
`adev->sdma.num_instances` wasn't declared when sdma_v2_4_init_microcode()
was run. This caused probing to fail.
Move the declaration to right before sdma_v2_4_init_microcode().
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3043
Fixes: 751e293f2c ("drm/amd: Move microcode init from sw_init to early_init for SDMA v2.4")
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add 3D LUT property for plane color transformations using a 3D lookup
table. 3D LUT allows for highly accurate and complex color
transformations and is suitable to adjust the balance between color
channels. It's also more complex to manage and require more
computational resources.
Since a 3D LUT has a limited number of entries in each dimension we want
to use them in an optimal fashion. This means using the 3D LUT in a
colorspace that is optimized for human vision, such as sRGB, PQ, or
another non-linear space. Therefore, userpace may need one 1D LUT
(shaper) before it to delinearize content and another 1D LUT after 3D
LUT (blend) to linearize content again for blending. The next patches
add these 1D LUTs to the plane color mgmt pipeline.
v3:
- improve commit message about 3D LUT
- describe the 3D LUT entries and size (Harry)
v4:
- advertise 3D LUT max size as the size of a single-dimension
v5:
- get lut3d blob correctly (Joshua)
- fix doc about 3d-lut dimension size (Sebastian)
Signed-off-by: Melissa Wen <mwen@igalia.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add begin/end_use ring callbacks to disallow GFXOFF when
SDMA work is submitted and allow it again afterward.
This should avoid corner cases where GFXOFF is erroneously
entered when SDMA is still active. For now just allow/disallow
GFXOFF in the begin and end helpers until we root cause the
issue. This should not impact power as SDMA usage is pretty
minimal and GFXOSS should not be active when SDMA is active
anyway, this just makes it explicit.
v2: move everything into sdma5.2 code. No reason for this
to be generic at this point.
v3: Add comments in new code
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2220
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com> (v1)
Tested-by: Mario Limonciello <mario.limonciello@amd.com> (v1)
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.15+
With WBRF feature supported, as a driver responding to the frequencies,
amdgpu driver is able to do shadow pstate switching to mitigate possible
interference(between its (G-)DDR memory clocks and local radio module
frequency bands used by Wifi 6/6e/7).
--
v1->v2:
- update the prompt for feature support(Lijo)
v8->v9:
- update parameter document for smu_wbrf_event_handler(Simon)
v9->v10:
v10->v11:
- correct the logics for wbrf range sorting(Lijo)
v13:
- Fix the format issue (IIpo Jarvinen)
Signed-off-by: Evan Quan <quanliangl@hotmail.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Ma Jun <Jun.Ma2@amd.com>
Signed-off-by: Ma Jun <Jun.Ma2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use drm_gem_prime_fd_to_handle to import DMABufs for interop. This
ensures that a GEM handle is created on import and that obj->dma_buf
will be set and remain set as long as the object is imported into KFD.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Ramesh Errabolu <Ramesh.Errabolu@amd.com>
Reviewed-by: Xiaogang.Chen <Xiaogang.Chen@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Create GEM handles for exporting DMABufs using GEM-Prime APIs. The GEM
handles are created in a drm_client_dev context to avoid exposing them
in user mode contexts through a DMABuf import.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Ramesh Errabolu <Ramesh.Errabolu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1. Use the mirrored topology info to fill links for VF.
The new solution is required to simplify and optimize host driver logic.
Only use the new solution for VFs that support full duplex and
extended_peer_link_info otherwise the info would be incomplete.
2. avoid calling extended_link_info on VF as its not supported
Signed-off-by: Vignesh Chander <Vignesh.Chander@amd.com>
Reviewed-by: Zhigang Luo <zhigang.luo@amd.com>
Reviewed-by: Jonathan Kim <jonathan.kim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Multiplier to 'gain' the plane. When PQ is decoded using the fixed func
transfer function to the internal FP16 fb, 1.0 -> 80 nits (on AMD at
least) When sRGB is decoded, 1.0 -> 1.0. Therefore, 1.0 multiplier = 80
nits for SDR content. So if you want, 203 nits for SDR content, pass in
(203.0 / 80.0).
v4:
- comment about the PQ TF need for L-to-NL (from Harry's review)
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Co-developed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Allow userspace to tell the kernel driver the input space and,
therefore, uses correct predefined transfer function (TF) to go from
encoded values to linear values.
v2:
- rename TF enum prefix from DRM_ to AMDGPU_ (Harry)
- remove HLG TF
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Co-developed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
