'aux_payloads' is unused since
commit eae5ffa9bd ("drm/amd/display: Switch ddc to new aux interface")
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When the link BW is smaller than the request BW,
the DP LT just kept running and fallback to lower link config.
DP LT just aborted if is_hpd_pending bit is high.
But is_hpd_pending bit indicates a new HPD event received.
It doesn't mean the HPD is low.
[How]
Abort the DP LT if the link BW is smaller than the request BW.
Remove checking is_hpd_pending bit in DP LT.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Cruise <cruise.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
UHBR13.5 support is optional, even if UHBR20 is supported by the device.
If source supports max UHBR13.5 while sink, cable and LTTPR support
UHBR20 but not UHBR13.5, UHBR10 should be used as the max link cap.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Switching between DSC clock or disable DSC block are not double buffered update.
Corruption is observed if these updates happen before DSC double buffered
disconnection.
[how]
Move DSC disable and refclk reset to post unlock update. Wait for DSC double buffered
disconnection and all mpccs are disconnected before reset DSC clock.
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Input mode for the DIG FIFO should be programmed as part of stream
encoder setup.
[HOW]
Pre-calculate the pixels per cycle as part of the pixel clock params,
and program as part of stream encoder setup.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For addtion (uint8_t) variable + constant 1,
coverity generates message below:
Truncation due to cast operation on "cur_idx + 1" from
32 to 8 bits.
Then Coverity assume result is 32 bits value be saved into
8 bits variable. When result is used as index to access
array, Coverity suspects index invalid.
[How]
Change varaible type to uint32_t.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During DP tunnel creation, CM preallocates BW and reduces
estimated BW of other DPIA. CM release preallocation only
when allocation is complete. Display mode validation logic
validates timings based on bw available per host router.
In multi display setup, this causes bw allocation failure
when allocation greater than estimated bw.
[How]
Do zero alloc to make the CM to release preallocation and
update estimated BW correctly for all DPIAs per host router.
Reviewed-by: PeiChen Huang <peichen.huang@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Upon disconnecting a UHBR SST display, the disconnection and the
SetTimings to disable the display can occur such that link_set_dpms_off
occurs after the disconnection has already processed
(link->type is dc_connection_none). Thus, the AUX related
operations should be skipped when clearing the payload allocation table.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
TCON data is corrupted after electro static discharge test.
Once the TCON data get corrupted, they will get themselves
reset and send HPD_IRQ to source side.
[How]
Support HPD_IRQ for internal link, and restore the PSR/Replay setup.
Reviewed-by: Robin Chen <robin.chen@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Sung-huai Wang <danny.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some of the includes used in the DC can be removed and others need to be
update. This commit adjusts some of those headers in the display code.
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
why and how:
as part of cleanup, need to refactor vpg. It was improperly referenced
as a dcn specfic part of link. the dcn agnostic code needed was ripped out
and put into vpg.h, now in dc/inc/hw.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Parandhaman K <parandhaman.k@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Enabling higher compiler warning levels results in many issues that can
be trivially resolved as well as some potentially critical issues.
[how]
Fix all compiler warnings found with various compilers and higher
warning levels. Primarily, potentially uninitialized variables and
unreachable code.
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The function to count the number of valid connectors does not
guarantee that the first n indices are valid, only that there
exist n valid indices. When invalid indices are present, this
results in later valid connectors being missed, as processing
would end after checking n indices.
[How]
- count valid indices separately from total indices examined
- add explicit definition of MAX_LINKS
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Dmub provides several Replay residency calculation methods,
but current interface only supports either ALPM or PHY mode
[How]
Modify the interface for supporting different types
of Replay residency calculation.
Reviewed-by: Robin Chen <robin.chen@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Leon Huang <leon.huang1@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In the first if statement, we're checking if 'replay' is NULL. But in
the second if statement, we're not checking if 'replay' is NULL again
before calling replay->funcs->replay_set_power_opt().
if (replay == NULL && force_static)
return false;
...
if (link->replay_settings.replay_feature_enabled &&
replay->funcs->replay_set_power_opt) {
replay->funcs->replay_set_power_opt(replay, *power_opts, panel_inst);
link->replay_settings.replay_power_opt_active = *power_opts;
}
If 'replay' is NULL, this will cause a null pointer dereference.
Fixes the below found by smatch:
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_edp_panel_control.c:895 edp_set_replay_allow_active() error: we previously assumed 'replay' could be null (see line 887)
Fixes: c7ddc0a800 ("drm/amd/display: Add Functions to enable Freesync Panel Replay")
Cc: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Cc: Roman Li <roman.li@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Tom Chung <chiahsuan.chung@amd.com>
Suggested-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Need to fix some broken logic and sequencing in initial commit
[HOW]
Fix logic handling override deprogramming when exiting SQ128.
Don't exit early from dp_set_hw_lane_settings for DP2/FIXED_VS case.
Move LTTPR 128b/132b check out of requires_hwss and check during
runtime, as LTTPR caps are not populated on initial call.
Add pending_test_pattern to link state to allow HWSS to set FFE overrides
on retimer TX and/or skip setting APU TX FFE depending on requested pattern.
Use updated clock source for SQ128 override sequence.
Skip HW FFE preset programming when performing test pattern overrides.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
wait_time_microsec = max(wait_time_microsec, (uint32_t)
DPIA_CLK_SYNC_DELAY);
Above line is trying to assign the maximum value between
'wait_time_microsec' and 'DPIA_CLK_SYNC_DELAY' to wait_time_microsec.
However, 'wait_time_microsec' has not been assigned a value before this
line, initialize 'wait_time_microsec' at the point of declaration.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dp_training_dpia.c:697 dpia_training_eq_non_transparent() error: uninitialized symbol 'wait_time_microsec'.
Fixes: 630168a973 ("drm/amd/display: move dp link training logic to link_dp_training")
Cc: Wenjing Liu <wenjing.liu@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Roman Li <roman.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some of the CONFIG_DRM_AMD_DC_FP was added in some non-related FPU code,
which may cause confusion. This commit dropped some of the unnecessary
guards.
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Only required if FIXED_VS retimer does not support DP2-capable.
[HOW]
Gate link rate toggle with DP 128b/132b LTTPR channel coding cap check.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The New sequence has been in use in DCN314 with no regressions
introduced. Therefore, it is safe to enable this sequence for all
devices using FIXED_VS retimers. So, remove the legacy codepath and its
associated config flag.
Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The error message buffer overflow 'dc->links' 12 <= 12 suggests that the
code is trying to access an element of the dc->links array that is
beyond its bounds. In C, arrays are zero-indexed, so an array with 12
elements has valid indices from 0 to 11. Trying to access dc->links[12]
would be an attempt to access the 13th element of a 12-element array,
which is a buffer overflow.
To fix this, ensure that the loop does not go beyond the last valid
index when accessing dc->links[i + 1] by subtracting 1 from the loop
condition.
This would ensure that i + 1 is always a valid index in the array.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dp_dpia_bw.c:208 get_host_router_total_dp_tunnel_bw() error: buffer overflow 'dc->links' 12 <= 12
Fixes: 59f1622a5f ("drm/amd/display: Add dpia display mode validation logic")
Cc: PeiChen Huang <peichen.huang@amd.com>
Cc: Aric Cyr <aric.cyr@amd.com>
Cc: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The 'status' variable in 'core_link_read_dpcd()' &
'core_link_write_dpcd()' was uninitialized.
Thus, initializing 'status' variable to 'DC_ERROR_UNEXPECTED' by default.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dpcd.c:226 core_link_read_dpcd() error: uninitialized symbol 'status'.
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dpcd.c:248 core_link_write_dpcd() error: uninitialized symbol 'status'.
Cc: stable@vger.kernel.org
Cc: Jerry Zuo <jerry.zuo@amd.com>
Cc: Jun Lei <Jun.Lei@amd.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clang warns (or errors with CONFIG_WERROR=y) when performing arithmetic
with different enumerated types, which is usually a bug:
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dp_dpia_bw.c:548:24: error: arithmetic between different enumeration types ('const enum dc_link_rate' and 'const enum dc_lane_count') [-Werror,-Wenum-enum-conversion]
548 | link_cap->link_rate * link_cap->lane_count * LINK_RATE_REF_FREQ_IN_KHZ * 8;
| ~~~~~~~~~~~~~~~~~~~ ^ ~~~~~~~~~~~~~~~~~~~~
1 error generated.
In this case, there is not a problem because the enumerated types are
basically treated as '#define' values. Add an explicit cast to an
integral type to silence the warning.
Closes: https://github.com/ClangBuiltLinux/linux/issues/1976
Fixes: 5f3bce1326 ("drm/amd/display: Request usb4 bw for mst streams")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
When usb4 bandwidth allocation mode is enabled, driver need to request
bandwidth from connection manager. For mst link, the requested
bandwidth should be big enough for all remote streams.
[HOW]
- If mst link, the requested bandwidth should be the sum of all mst
streams bandwidth added with dp MTPH overhead.
- Allocate/deallcate usb4 bandwidth when setting dpms on/off.
- When doing display mode validation, driver also need to consider total
bandwidth of all mst streams for mst link.
Reviewed-by: Cruise Hung <cruise.hung@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Peichen Huang <peichen.huang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
