This enables starting and stopping IPS residency measurements
and querying the IPS residency information consisting of residency
percent, entry counter, total time active & inactive, and histograms
for the specified IPS mode.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Ovidiu Bunea <Ovidiu.Bunea@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We intend to consolidate dp tunneling and conventional dp link training.
[HOW]
1. Use the same link training entry for both dp and dpia
2. Move SET_CONFIG of non-transparent mode to dmub side
3. Add set_tps_notification dmub_cmd to notify tps request for
non-transparent dpia link training
4. Check dpcd request result and abort link training early if dpia
aux tunneling fails
5. Add option to avoid affect old product
6. Separately handle wait_time_microsec for dpia
Reviewed-by: Cruise Hung <cruise.hung@amd.com>
Reviewed-by: George Shen <george.shen@amd.com>
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HPD sense changes can occur during low power states and need to be
notified from firmware to driver. Upon notification the hotplug
redetection routines should execute.
[How]
Add Support in DMUB srv and DMUB srv stat for receiving these
notifications. DM can hook them up and process the HPD redetection
once received.
Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We can hang in IPS2 checking DMCUB_SCRATCH0 for link detection state.
[How]
Replace the HW access with a check on the shared state bit. This will
work the same way as the SCRATCH0 but won't require a wake in the case
where link detection isn't required.
Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- Add logging for first DMUB inbox message that timed out to diagnostic
data
- It is useful to track the first failed message for debug purposes
because once DMUB becomes hung (typically on a message), it will
remain hung and all subsequent messages. In these cases we're
interested in knowing which is the first message that failed.
Reviewed-by: Josip Pavic <josip.pavic@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Read modify write hazards can occur when using a single shared scratch
register between driver and firmware leading to driver accessing DCN
in IPS2 and a system hang.
[How]
Add infrastructure for using REGION6 as a shared firmware state between
driver and firmware. This region is uncachable.
Replace the existing get/set idle calls with reads/writes to the
(volatile) shared firmware state blocks that a separated by at least
a cache line between firmware and driver.
Remove the workarounds that required rewriting/checking read modify
write hazards.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Display code keeps getting improvements, and because of that, some
legacy code is left behind. This commit drops some of those unused
codes.
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
1. To watch dmcub inbox1 ring buffer cmd type without tools
2. dmub_cmd_PLAT_54186_wa 66 bytes
[How]
Added dmcub cmd type enum: unsigned char for debug use only,
also fixed 66 bytes issue by using unsigned int in bit
define instead of unsigned char.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Fudongwang <fudong.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On resume from S3, while DMUB is inactive, DMUB queue and execute
calls will not work. Skip reporting errors in these scenarios
[How]
Add new return code during DMUB queue and execute calls when DMUB
is in S3 state. Skip logging errors in these scenarios
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Samson Tam <samson.tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On resume from S3, may get apply_idle_optimizations call while DMUB
is inactive which will just time out.
[How]
Set and track power state in dmub_srv and check power state before
sending commands to DMUB. Add interface in both dmub_srv and
dc_dmub_srv
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Samson Tam <samson.tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
SubVP needs to "calculate" the earliest in use META address
by using the current primary / meta addresses, but this leads
to a race condition where FW and driver can read/write the
address at the same time and intermittently produce inconsistent
address offsets. To mitigate this issue without locking (too slow),
save each surface flip addr into scratch registers and use this
to keep track of the earliest in use META addres.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
DMUB subsystem was continuing to use compile time offset calculation for
register access. Switch this to runtime calculation to stay consistent
with rest of DC code.
To enable this, an additional interface init_reg_offsets() are added to
DMUB's hw_funcs struct. Asics with runtime register offset calculation
enabled shall populate this hook with a fn pointer that will invoke the
necessary macros to calculate the offset.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This option can vary depending on the panel and may be required to be
called during sink detection phase before transmitter control.
[How]
Allow modify the bit depending on the eDP panel connected with a new
interface.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If optimized init is done in FW. DCN init can be skipped in driver. This
need to be communicated between driver and fw and maintain backwards
compatibility.
[How]
Use DMUB scratch 0 bit 2 to indicate optimized init done in fw and
use DMUB scatch 4 bit 0 to indicate drive supports the optimized flow
so FW will perform it.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Adding the new DPIA NOTIFY packets from DMUB
As per the design with Cruise to account for
250ms response delay otherwise
[HOW]
Added th DPIA NOTIFY logic as per DMUB logic
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Mustapha Ghaddar <mghaddar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Dpia hpd interrupt processing is disabled when entering S4/S0i3 and
would be reenabled after detection completes during resuming. Because,
keeping hpd interrupts enabled during detection leads to multiple
detections for the same hpd transition. There is a S4 case where dpia
hpd interrupt is missed when driver is in transitioning from hpd
interrupt processing disable to enable and the display does not light
up.
[How]
- Added dmub inbox command DMUB_CMD__DPIA_HPD_INT_ENABLE to explicitly
control dmub to issue dpia hpd interrupt or not. If dpia hpd interrupt
is disabled, dmub will keep the hpd pending and post it once driver
reenables dpia hpd interrupt or when querying with
DMUB_CMD__QUERY_HPD_STATE.
- Added dmub boot option dpia_hpd_int_enable_supported to notify dmub
about whether DMUB_CMD__DPIA_HPD_INT_ENABLE command would be used.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Mustapha Ghaddar <Mustapha.Ghaddar@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Boot up behaviour may differ depending on the Connection Manager
handling USB4 tunneling.
[How]
Send boot option to firmware to indicate Connection Manager.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We're currently flushing commands that had been previously been
flushed or are currently being processed by the DMCUB when we don't
immediately wait for idle after command execution.
[How]
Avoiding reflushing the data by keeping track of the last wptr.
We'll treat this as the actual rptr by creating a copy of the inbox
and modifying the copy's rptr.
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In DC we want to wait for the INBOX0 HW Lock command to ACK before
continuing. This is to ensure that the lock has been successfully
acquired before programming HW in DC.
[How]
Add interfaces to send messages on INBOX0, poll for their completation
and clear the ack.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During Z10, root clock gating and memory low power registers needs to
to be restored if optimization is enabled in driver.
[How]
Added new DMUB boot option for root clock gating and memory low power.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DMUB binary is common for both A0 and B0. Hence, driver should
notify FW about the support for DPIA in B0.
[How]
Added dpia_supported bit in dmub_fw_boot_options and will be set
only for B0.
Assign dpia_supported to true before dm_dmub_hw_init
in B0 case.
v2: fix build without CONFIG_DRM_AMD_DC_DCN (Alex)
Signed-off-by: Jude Shih <shenshih@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To process SET_CONFIG transactions with DMUB using inbox1 and
outbox1 mail boxes.
[How]
1) Added inbox1 DPIA command subtype DMUB_CMD__DPIA_SET_CONFIG_ACCESS to
issue SET_CONFIG command to DMUB in dc_process_dmub_set_config_async().
DMUB processes the command with DPIA sends reply back immediately or
in an outbox1 message triggering an outbox1 interrupt to driver.
2) DMUB posts SET_CONFIG reply as an Outbox1 message of type
DMUB_OUT_CMD__SET_CONFIG_REPLY.
3) The dmub async to sync mechanism for AUX is modified to accommodate
SET_CONFIG commands for both command issue and reply code paths.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Running into bugchecks during stress test where rptr is 0xFFFFFFFF.
Typically this is caused by a hard hang, and can come from HW outside
of DCN.
[How]
To prevent bugchecks when writing the DMUB rptr, fist check that the
rptr is valid.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When system is in Z10 HPD interrupts cannot fire, we may miss display
configuration changes.
[How]
When Zstate is enabled, if DMUB indicate DCN has lost power, do a
complete detection periodically.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
