[Why]
Playing 1080p video on 4k60 timing uses UCLK DPM5 and mode support
determines that p-state switching is not supported.
[How]
Allow DML to increase latency as the last strategy so strategies such
as VBlank p-state switching may become possible
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Austin Zheng <Austin.Zheng@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Idle worker thread serves for periodic detection of HPD while system is in IPS2.
Currently it is used in headless and static screen scenarios.
IPX can be configured not to execute IPS2 for static screen.
In this case idle worker is redundant.
[How]
Only use periodic detection for static screen if IPS is fully enabled.
Reviewed-by: Sun peng Li <sunpeng.li@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Viewport size excess surface size observed sometime with some timings or
resizing the MPO video window to cause MPO unsupported. Calculate final
viewport size first with a 100x100 dummy viewport to get the max TAP
support and then re-run final viewport calculation if TAP value changed.
Removed obsolete preliminary viewport calculation for TAP validation.
Reviewed-by: Dmytro Laktyushkin <dmytro.laktyushkin@amd.com>
Signed-off-by: Yihan Zhu <Yihan.Zhu@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Since the surface/stream update flags aren't cleared after applying
updates, those same updates may be applied again in a future call to
update surfaces/streams for surfaces/streams that aren't actually part
of that update (i.e. applying an update for one surface/stream can
trigger unintended programming on a different surface/stream).
For example, when an update results in a call to
program_front_end_for_ctx, that function may call program_pipe on all
pipes. If there are surface update flags that were never cleared on the
surface some pipe is attached to, then the same update will be
programmed again.
[How]
Clear the surface and stream update flags after applying the updates.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3441
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3616
Cc: Melissa Wen <mwen@igalia.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Regamma resolution for the first few black levels can have problems for
calibration.
[HOW]
HW LUT is divided into N power-of-2 regions each with K segments. For
SDR mode we set min point at 2^-10 and increments of 2^-13. It's
generally more than 8-bit SDR needs, but some calibration tools and API
use 12-bit curves.
The fix shifts starting point to 2^-12 and starting increments at 2^-16.
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Signed-off-by: Peterson <peterson.guo@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When Source extend the vblank to reach the minimum panel
refresh rate, the vtotal length could have 1 line longer
than the maximum supported vtotal.
The reason is we optimized the vtotal/refresh-rate calculation
to get more accurate vtotal number by rounding the calculation
result. But when the target refresh rate is the minimum
refresh rate, the vtotal result could be round up and over
the maximum supported vtotal.
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Signed-off-by: po-tchen <robin.chen@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For some EDP to MIPI panel, disabling OTG when link is alive like boot
case, the converter might output garbage or show no display because our
GPU is not sending required pixel data.
Alos Dig fifo underflow was found which might cause garbage, when
resetting otg for other types of EDP panels.
[How]
Skipping resetting OTG if the dig fifo is on. Make sure that the otg for
the pipe is the one that the dig fifo is selecting via the FE mask.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Zhongwei <Zhongwei.Zhang@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The MPO plane will receive a flip but
desktop plane may not receive a flip when GSL is enabled.
As a result, system will be stuck waiting for a flip that was never sent.
[How]
Set update address update flag of all flip_immediate planes
if there are multiple planes.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Austin Zheng <Austin.Zheng@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Resync FIFO is a workaround to write the same value to
DENTIST_DISPCLK_CNTL register after programming OTG_PIXEL_RATE_DIV
register, in case seemless boot, there is no OTG_PIXEL_RATE_DIV register
update, so skip CRTC disable when resync FIFO to avoid random FIFO error
and garbage.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Fudongwang <Fudong.Wang@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dcn32_blank_phantom() does not consider the subVP+ODM case when blanking.
Only one of the pipes will get blanked. Remaining pipes are not blanked.
Will cause underflow in the phantom pipe when enabling the CRTC.
[How]
Use blank_pixel_data() instead of blank_phantom().
remove dcn32_blank_phantom() since logic is identical.
Different DPG dimensions get programmed when blanking phantom pipes.
Previously had phantom pipes use DPG dimensions of the main stream.
Now use DPG dimensions of the phantom streams
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Austin Zheng <Austin.Zheng@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update the *handle to amdgpu_ip_block ptr for all
functions pointers of hw_fini.
Also update the ip_block ptr where ever needed as
there were cyclic dependency of hw_fini on suspend
and some followed clean up.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update the *handle to amdgpu_ip_block ptr for all
functions pointers of hw_init.
Also update the ip_block ptr where ever needed as
there were cyclic dependency of hw_init on resume.
v2: squash in isp fix
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reorganize kerneldoc parameter names to match the parameter
order in the function header.
Problems identified using Coccinelle.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC 3.2.303 contains some improvements as summarized below:
* Improve brightness control
* Add support for UHBR10 eDP
* OPTC required only for DTBCLK_P for dcn401
* Fix TBT monitor resume issue
* Code cleanup
Reviewed-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DTBCLK_P is used to generate virtual pixel clock, and to drive the HPO
stream encoder clock. Programming the required clock when
enabling/disabling both components can cause issues.
For example, if HPO is being disabled and clock source is changed to
REFCLK, virtual pixel rate will then be wrong, causing issues in CRTC.
[HOW]
Only program the DTBCLK_P when programming CRTC, as its expected it will
be enabled prior to HPO, and disabled after HPO in all valid cases.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This enables starting and stopping IPS residency measurements
and querying the IPS residency information consisting of residency
percent, entry counter, total time active & inactive, and histograms
for the specified IPS mode.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Ovidiu Bunea <Ovidiu.Bunea@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
A number of values are assigned to variables but the stored values are
not used afterwards.
[HOW]
The assignments are removed. If the variables are not used, they are
removed as well.
This fixes 9 UNUSED_VALUE issues reported by Coverity.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
MacroTileSizeBytes is set to either 256 or 65535 and it is never
4096. Its branch is not taken, and should be removed. Similarly,
mode_422 is always 0 and thus ppe will always be 1. The ternary
operator should be removed.
This fixes 2 DEADCODE issues reported by Coverity.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Prioritize Aux-based over PWM-based brightness control
for more types of panels and introduce a new structure
to store and manage the type of brightness control used.
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Signed-off-by: Muyuan Yang <muyuan.yang@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are some issues which customer only can provide full
dump for analyze, without register history, it's hard to
debug HW status.
[How]
1. Put register read/write into WPP log so we can trace the logs
from full memory dump.
2. MALL doesn't add into WPP, add it.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Connected with a Thunderbolt monitor and do the suspend and the system
may hang while resume.
The TBT monitor HPD will be triggered during the resume procedure
and call the drm_client_modeset_probe() while
struct drm_connector connector->dev->master is NULL.
It will mess up the pipe topology after resume.
[How]
Skip the TBT monitor HPD during the resume procedure because we
currently will probe the connectors after resume by default.
Reviewed-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If two monitors with TMDS signals were timing synced and one was
disconnected, the stream would go out of sync too early due to
the PLL turning off and the system could hang
[How]
On link disable output, change PHY FSM transition from TX_EN-to-PHY_OFF
to TX_EN-to-PLL_ON for TMDS
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Ryan Seto <ryanseto@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are more IPS modes other than DMUB_IPS_ENABLE that enables IPS. We
need to enable the hotplug detect idle workqueue for those modes as
well.
[How]
Modify the if condition to initialize the workqueue in all IPS modes
except for DMUB_IPS_DISABLE_ALL.
Fixes: 65444581a4 ("drm/amd/display: Determine IPS mode by ASIC and PMFW versions")
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current state should be used when waiting for DET update
instead of new context.
For any streams decreasing in DET, pipes used in the current state
should be checked since those pipes need to free their DET before
DET can be reallocated.
[How]
Pass in current_state instead of context.
Use pipe from current_state instead of context. This assumes that
pipe in the current_state is an OTG_MASTER pipe if the pipe in the context is an OTG_MASTER pipe.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Austin Zheng <Austin.Zheng@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
