Permanently set the connector status to 'connected'. Return BMC modes
for connector if no display is attached to the physical DP connector.
Otherwise use EDID modes as before.
If the status of the physical connector changes, the driver still
generates a hotplug event. DRM clients will then reconfigure their
output to a mode appropriate for either physical display or BMC.
v3:
- use struct ast_connector.physical_status to handle BMC
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240815151953.184679-7-tzimmermann@suse.de
Convert ASTDP support to struct drm_edid and its helpers. Simplifies
and modernizes the EDID handling.
The driver reads 4 bytes at once, but the overall read length is now
variable. Therefore update the EDID read loop to never return more than
the requested bytes.
The device does not seem to support EDID extensions, as the driver
actively clears any such information from the main EDID header. As
the new interface allows for reading extension blocks for EDID, make
sure that the block is always 0 (i.e., the main header). A later
update might fix that.
v2:
- fix reading if len is not a multiple of 4
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240815151953.184679-5-tzimmermann@suse.de
The place for link training is in the encoder's atomic_enable
helper. Remove all related tests from other helper ASTDP functions;
especially ast_astdp_is_connected(), which tests HPD status.
DP link training is controlled by the firmware. A status flag reports
success or failure. The process can be fragile on Aspeed hardware. Moving
the test from connector detection to the atomic_enable allows for several
retries and a longer timeout.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240717143319.104012-5-tzimmermann@suse.de
Aspeed always report the display port as "connected", because it
doesn't set a .detect_ctx callback.
Fix this by providing the proper detect callback for astdp and dp501.
This also fixes the following regression:
Since commit fae7d18640 ("drm/probe-helper: Default to 640x480 if no
EDID on DP") The default resolution is now 640x480 when no monitor is
connected. But Aspeed graphics is mostly used in servers, where no monitor
is attached. This also affects the remote BMC resolution to 640x480, which
is inconvenient, and breaks the anaconda installer.
v2: Add .detect callback to the dp/dp501 connector (Jani Nikula)
v3: Use .detect_ctx callback, and refactors (Thomas Zimmermann)
Add a BMC virtual connector
v4: Better indent detect_ctx() functions (Thomas Zimmermann)
v5: Enable polling of the dp and dp501 connector status
(Thomas Zimmermann)
v6: Change check order in ast_astdp_is_connected (Jammy Huang)
Fixes: fae7d18640 ("drm/probe-helper: Default to 640x480 if no EDID on DP")
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230713134316.332502-2-jfalempe@redhat.com
V1:
1. The MCU FW controling ASPEED DP is loaded by BMC boot loader.
2. Driver starts after CR[3:1] == 111b that indicates Tx is ASTDP,
and CRD1[5] has been asserted by BMVC boot loader.
3. EDID is prioritized by DP monitor.
4. DP's EDID has high priority to decide resolution supporting.
V2:
Modules description:
1. ASTDP (ASPEED DisplayPort) is controlled by dedicated
AST-MCU (ASPEED propriatary MCU).
2. MCU is looping in charged of HPD, Read EDID, Link Training with
DP sink.
3. ASTDP and AST-MUC reside in BMC (Baseboard Management controller)
addressing-space.
4. ASPEED DRM driver requests MCU to get HPD and EDID by CR-scratched
register.
Booting sequence:
1. Check if TX is ASTDP // ast_dp_launch()
2. Check if DP-MCU FW has loaded // ast_dp_launch()
3. Read EDID // ast_dp_read_edid()
4. Resolution switch // ast_dp_SetOutput()
V3:
1. Remove unneeded semicolon.
2. Apply to git://anongit.freedesktop.org/drm/drm, instead of
git://anongit.freedesktop.org/drm/drm-misc
3. Resolve auto build test WARNINGs on V1 patch.
V4:
1. Sync code-base with kernel 5.17_rc6
2. Remove the define of DPControlPower, because DP chips need to be
powered on to be used.
3. Remove the switches of PHY and Display from EDID procedure.
4. Revise increaing delay to fixed delay, because this version kernel
doesn't detect minitor consistenntly.
5. Create clean-up code used for reset of power state on errors with
-EIO manner.
6. Revise the DP detection by TX type and its DP-FW status during
booting and resume.
7. Correct the CamelCase Style.
8. Use register reading while needing, and remove to hold full
register.
9. Instead of 'u8', revise to 'bool' on swwitch of PHY and video.
10.Correct typo
11.Remove the duplicated copy of TX definition.
12.Use EDID_LENGTH as the constant of 128.
Signed-off-by: KuoHsiang Chou <kuohsiang_chou@aspeedtech.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220428075603.20904-1-kuohsiang_chou@aspeedtech.com
