On sa8775p-ride-r3 the RX clocks from the AQR115C PHY are not available at
the time of the DMA reset. We can however extract the RX clock from the
internal SERDES block. Once the link is up, we can revert to the
previous state.
The AQR115C PHY doesn't support in-band signalling so we can count on
getting the link up notification and safely reuse existing callbacks
which are already used by another HW quirk workaround which enables the
functional clock to avoid a DMA reset due to timeout.
Only enable loopback on revision 3 of the board - check the phy_mode to
make sure.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240703181500.28491-3-brgl@bgdev.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 070246e467 ("net: stmmac: Fix for mismatched host/device DMA
address width") added support in the stmmac driver for platform drivers
to indicate the host DMA width, but left it up to authors of the
specific platforms to indicate if their width differed from the addr64
register read from the MAC itself.
Qualcomm's EMAC4 integration supports only up to 36 bit width (as
opposed to the addr64 register indicating 40 bit width). Let's indicate
that in the platform driver to avoid a scenario where the driver will
allocate descriptors of size that is supported by the CPU which in our
case is 36 bit, but as the addr64 register is still capable of 40 bits
the device will use two descriptors as one address.
Fixes: 8c4d92e82d ("net: stmmac: dwmac-qcom-ethqos: add support for emac4 on sa8775p platforms")
Signed-off-by: Sagar Cheluvegowda <quic_scheluve@quicinc.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updating link clock rate for different speeds is only needed when
using RGMII, as that mode requires changing clock speed when the link
speed changes. Let's restrict updating the link clock speed in
ethqos_update_link_clk() to just RGMII. Other modes such as SGMII
only need to enable the link clock (which is already done in probe).
Signed-off-by: Sarosh Hasan <quic_sarohasa@quicinc.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Reviewed-by: Abhishek Chauhan <quic_abchauha@quicinc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Serdes phy needs to operate at 2500 mode for 2.5G speed and 1000
mode for 1G/100M/10M speed.
Added changes to configure serdes phy and mac based on link speed.
Changing serdes phy speed involves multiple register writes for
serdes block. To avoid redundant write operations only update serdes
phy when new speed is different.
For 2500 speed MAC PCS autoneg needs to disabled. Added changes to
disable MAC PCS autoneg if ANE parameter is not set.
Signed-off-by: Sneh Shah <quic_snehshah@quicinc.com>
Tested-by: Abhishek Chauhan <quic_abchauha@quicinc.com> # sa8775p-ride
Reviewed-by: Abhishek Chauhan <quic_abchauha@quicinc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TSO and TBS cannot co-exist. TBS requires special descriptor to be
allocated at bootup. Initialising Tx queues at probe to support
TSO and TBS can help in allocating those resources at bootup.
TX queues with TBS can support etf qdisc hw offload.
This is similar to the patch raised by NXP
commit 3b12ec8f61 ("net: stmmac: dwmac-imx: set TSO/TBS TX queues default settings")
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Abhishek Chauhan <quic_abchauha@quicinc.com>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Acked-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230727014944.3972546-1-robh@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Qualcomm clocks can set their frequency to a variety of levels
generally. Let's use the max for clk_ptp_ref to ensure the best
timestamping resolution possible.
Without this, the default value of the clock is used. For sa8775p-ride
this is 19.2 MHz, far less than the 230.4 MHz possible.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230725211853.895832-4-ahalaney@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Using dev_err_probe() logs to devices_deferred which is helpful
when debugging.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since this driver only uses devicetree, let's move over to
of_get_phy_mode(). That API has an explicit error return and produces a
phy_interface_t directly instead of an int when representing the phy
mode.
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
sa8775p uses EMAC version 4, add the relevant defines, rename the
has_emac3 switch to has_emac_ge_3 (has emac greater-or-equal than 3)
and add the new compatible.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On sa8775p the MAC is connected to the external PHY over SGMII so add
support for it to the driver.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation for supporting SGMII, let's make the code a bit more
generic. Add a new callback for MAC configuration so that we can assign
a different variant of it in the future.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On sa8775p, the EMAC revision is 4 and we use SGMII instead of RGMII.
There's no "rgmii" clock but there's a fourth clock under a different
name: "phyaux". Add a new field to the chip data struct that specifies
the link clock name. Default to "rgmii" for backward compatibility.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On sa8775p platforms, there's a SGMII SerDes PHY between the MAC and
external PHY that we need to enable and configure.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The err_mem label's name is unclear. It actually should be reached on
any error after stmmac_probe_config_dt() succeeds. Name it after the
cleanup action that needs to be called before exiting.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We can use a devm action to completely drop the remove callback and use
stmmac_pltfr_remove() directly for remove. We can also drop one of the
goto labels.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR.
Conflicts:
net/sched/sch_taprio.c
d636fc5dd6 ("net: sched: add rcu annotations around qdisc->qdisc_sleeping")
dced11ef84 ("net/sched: taprio: don't overwrite "sch" variable in taprio_dump_class_stats()")
net/ipv4/sysctl_net_ipv4.c
e209fee411 ("net/ipv4: ping_group_range: allow GID from 2147483648 to 4294967294")
ccce324dab ("tcp: make the first N SYN RTO backoffs linear")
https://lore.kernel.org/all/20230605100816.08d41a7b@canb.auug.org.au/
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We must not assign plat_dat->dwmac4_addrs unconditionally as for
structures which don't set them, this will result in the core driver
using zeroes everywhere and breaking the driver for older HW. On EMAC < 2
the address should remain NULL.
Fixes: b68376191c ("net: stmmac: dwmac-qcom-ethqos: Add EMAC3 support")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The remove callback is only ever called after .probe() returned
successfully. After that get_stmmac_bsp_priv() always return non-NULL.
Side note: The early exit would also be a bug because the return value
of qcom_ethqos_remove() is ignored by the device core and the device is
unbound unconditionally. So exiting early resulted in a dangerous
resource leak as all devm allocated resources (some memory and the
register mappings) are freed but the network device stays around. Using
the network device afterwards probably oopses.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The function returns zero unconditionally. Change it to return void instead
which simplifies some callers as error handing becomes unnecessary.
The function is also used for some drivers as remove callback. Switch these
to the .remove_new() callback. For some others no error can happen in the
remove callback now, convert them to .remove_new(), too.
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It seems that this variable should be used for all speeds, not just
1000/100.
While at it refactor it slightly to be more readable, including fixing
the typo in the variable name.
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The driver currently sets a MAC TX delay of 2 ns no matter what the
phy-mode is. If the phy-mode indicates the phy is in charge of the
TX delay (rgmii-txid, rgmii-id), don't do it in the MAC.
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The driver is specific to ARCH_QCOM which depends on OF thus the driver
is OF-only. Its of_device_id table is built unconditionally, thus
of_match_ptr() for ID table does not make sense.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently in phy_init_eee() the driver unconditionally configures the PHY
to stop RX_CLK after entering Rx LPI state. This causes an LPI interrupt
storm on my qcs404-base board.
Change the PHY initialization so that for "qcom,qcs404-ethqos" compatible
device RX_CLK continues to run even in Rx LPI state.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the Qualcomm ethqos driver is properly described in its associated
GDSC power-domain, the hardware will be powered down and loose its state
between qcom_ethqos_probe() and stmmac_init_dma_engine().
The result of this is that the functional clock from the RGMII IO macro
is no longer provides and the DMA software reset in dwmac4_dma_reset()
will time out, due to lacking clock signal.
Re-enable the functional clock, as part of the Qualcomm specific clock
enablement sequence to avoid this problem.
The final clock configuration will be adjusted by ethqos_fix_mac_speed()
once the link is being brought up.
Fixes: a7c30e62d4 ("net: stmmac: Add driver for Qualcomm ethqos")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-and-reviewed-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Link: https://lore.kernel.org/r/20220323033255.2282930-1-bjorn.andersson@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Not all platforms should have RGMII_CONFIG_LOOPBACK_EN and the result it
about 50% packet loss on incoming messages. So make it possile to
configure this per compatible and enable it for QCS404.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds compatible, POR config & driver data for ethernet controller
found in SM8150 SoC.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
[bhsharma: Massage the commit log and other cosmetic changes]
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
dwmac-qcom-ethqos currently exposes a mechanism to dump rgmii registers
after the 'stmmac_dvr_probe()' returns. However with commit
5ec5582343 ("net: stmmac: add clocks management for gmac driver"),
we now let 'pm_runtime_put()' disable the clocks before returning from
'stmmac_dvr_probe()'.
This causes a crash when 'rgmii_dump()' register dumps are enabled,
as the clocks are already off.
Since other dwmac drivers (possible future users as well) might
require a similar register dump feature, introduce a platform level
callback to allow the same.
This fixes the crash noticed while enabling rgmii_dump() dumps in
dwmac-qcom-ethqos driver as well. It also allows future changes
to keep a invoking the register dump callback from the correct
place inside 'stmmac_dvr_probe()'.
Fixes: 5ec5582343 ("net: stmmac: add clocks management for gmac driver")
Cc: Joakim Zhang <qiangqing.zhang@nxp.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split clocks settings from init callback into clks_config callback,
which could support platform level clock management.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
