Issuing a system suspend command raises the following warning:
WARNING: CPU: 0 PID: 15 at drivers/mmc/core/sdio.c:1042 mmc_sdio_suspend+0xd4/0x19c
CPU: 0 PID: 15 Comm: kworker/u2:1 Not tainted 6.7.0-rc1-wt+ #710
Hardware name: Atmel SAMA5
Workqueue: events_unbound async_run_entry_fn
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x34/0x48
dump_stack_lvl from __warn+0x98/0x160
__warn from warn_slowpath_fmt+0xcc/0x140
warn_slowpath_fmt from mmc_sdio_suspend+0xd4/0x19c
mmc_sdio_suspend from mmc_bus_suspend+0x50/0x70
mmc_bus_suspend from dpm_run_callback+0xe4/0x248
dpm_run_callback from __device_suspend+0x234/0x91c
__device_suspend from async_suspend+0x24/0x9c
async_suspend from async_run_entry_fn+0x6c/0x210
async_run_entry_fn from process_one_work+0x3a0/0x870
[...]
This warning is due to a check in SDIO core ensuring that interrupts do not
remain enabled for cards being powered down during suspend. WILC driver
currently does not set the MMC_PM_KEEP_POWER flag, so disable interrupt
when entering resume.
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240613-wilc_suspend-v1-6-c2f766d0988c@bootlin.com
WILC1000 suspend/resume implementation is currently composed of two parts:
suspend/resume ops implemented in cfg80211 ops, which merely sets a
flag, and suspend/resume ops in sdio/spi driver which, based on this flag,
execute or not the suspend/resume mechanism. This dual set of ops is not
really needed , so keep only the sdio part to implement suspend/resume.
While doing so, remove the now unused suspend_event flag.
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240613-wilc_suspend-v1-5-c2f766d0988c@bootlin.com
host_wakeup_notify and host_sleep_notify are surrounded by chip_wakeup and
chip_allow_sleep calls, which theorically need to be protected with the
hif_cs lock. This lock protection is currently missing. Instead of adding
the lock where those two functions are called, move those in host->chip
suspend notifications to benefit from the lock already used there (in
bus_acquire/bus_release)
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240613-wilc_suspend-v1-2-c2f766d0988c@bootlin.com
Driver systematically disables some power mechanism each time it starts the
chip firmware (so mostly when interface is brought up). This has a negative
impact on some specific scenarios when the chip is exposed as a
hotpluggable SDIO card (eg: WILC1000 SD):
- when executing suspend/resume sequence while interface has been brought
up
- rebooting the platform while module is plugged and interface has been
brought up
Those scenarios lead to mmc core trying to initialize again the chip which
is now unresponsive (because of the power sequencer setting), so it fails
in mmc_rescan->mmc_attach_sdio and enter a failure loop while trying to
send CMD5:
mmc0: error -110 whilst initialising SDIO card
mmc0: error -110 whilst initialising SDIO card
mmc0: error -110 whilst initialising SDIO card
[...]
Preventing the driver from disabling this "power sequencer" fixes those
enumeration issues without affecting nominal operations.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240613-wilc_suspend-v1-1-c2f766d0988c@bootlin.com
The default netdev interface exposed by WILC1000 is registered at probe,
but the chip mac address is not known until ndo_open, which will load and
start chip firmware and then retrieve stored MAC address from it. As a
consequence, the interface has uninitialized value (00:00:00:00:00) until a
user brings up the interface.
Fix MAC address at probe by setting the following steps:
- at probe, read MAC address directly from fuse
- whenever a new netdevice is created, apply saved mac address (which can
be a user-provided address, or the eFuse Mac address if no address has
been passed by user)
- whenever an interface is brought up for the first time (and so the
firmware is loaded and started), enforce netdevice mac address to the
chip (in case user has changed it)
Reported-by: Heiko Thiery <heiko.thiery@gmail.com>
Closes: https://lore.kernel.org/netdev/CAEyMn7aV-B4OEhHR4Ad0LM3sKCz1-nDqSb9uZNmRWR-hMZ=z+A@mail.gmail.com/T/
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Co-developed-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240514-mac_addr_at_probe-v2-6-afef09f1cd10@bootlin.com
In order to be able to read raw registers (eg the nv mac address) in
wilc1000 during probe before the firmware is loaded and running, we need to
run the basic sdio functions initialization, but then we also need to
properly deinitialize those right after, to preserve the current driver
behavior (keeping the chip idle/unconfigured until the corresponding
interface is brought up). Calling wilc_sdio_deinit in its current form is
not enough because it merely resets an internal flag.
Implement a deinit sequence which symmetrically reset all steps performed
in wilc_sdio_init (only for parts activating/deactivating features, for the
sake of simplicity, let's ignore blocks size configuration reset)
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240514-mac_addr_at_probe-v2-5-afef09f1cd10@bootlin.com
SDIO/SPI probes functions automatically add a default wlan interface on top
of registered wiphy, through wilc_cfg80211_init which in turn calls
wilc_netdev_ifc_init. However, bus is still not fully initialized when we
register corresponding net device (for example we still miss some private
driver data pointers), which for example makes it impossible to
retrieve MAC address from chip (which is supposed to be set on net device
before its registration) before registering net device. More generally, net
device registration should not be done until driver has fully initialized
everything and is ready to handle any operation on the net device.
Prevent net device from being registered so early by doing it at the end of
probe functions. Apply this logic to both sdio and spi buses.
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240514-mac_addr_at_probe-v2-2-afef09f1cd10@bootlin.com
Smatch complains that there is a double free in probe:
drivers/net/wireless/microchip/wilc1000/spi.c:186 wilc_bus_probe() error: double free of 'spi_priv'
drivers/net/wireless/microchip/wilc1000/sdio.c:163 wilc_sdio_probe() error: double free of 'sdio_priv'
The problem is that wilc_netdev_cleanup() function frees "wilc->bus_data".
That's confusing and a layering violation. Leave the frees in probe(),
delete the free in wilc_netdev_cleanup(), and add some new frees to the
remove() functions.
Fixes: dc8b338f3b ("wilc1000: use goto labels on error path")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211217150311.GC16611@kili
