After the previous patch that speeded up the test (by avoiding neigh
discovery in IPv6), the BPF CI occasionally hits this error:
rcv tstamp unexpected pkt rcv tstamp: actual 0 == expected 0
The test complains about the cmsg returned from the recvmsg() does not
have the rcv timestamp. Setting skb->tstamp or not is
controlled by a kernel static key "netstamp_needed_key". The static
key is enabled whenever this is at least one sk with the SOCK_TIMESTAMP
set.
The test_redirect_dtime does use setsockopt() to turn on
the SOCK_TIMESTAMP for the reading sk. In the kernel
net_enable_timestamp() has a delay to enable the "netstamp_needed_key"
when CONFIG_JUMP_LABEL is set. This potential delay is the likely reason
for packet missing rcv timestamp occasionally.
This patch is to create udp sockets with SOCK_TIMESTAMP set.
It sends and receives some packets until the received packet
has a rcv timestamp. It currently retries at most 5 times with 1s
in between. This should be enough to wait for the "netstamp_needed_key".
It then holds on to the socket and only closes it at the end of the test.
This guarantees that the test has the "netstamp_needed_key" key turned
on from the beginning.
To simplify the udp sockets setup, they are sending/receiving packets
in the same netns (ns_dst is used) and communicate over the "lo" dev.
Hence, the patch enables the "lo" dev in the ns_dst.
Fixes: c803475fd8 ("bpf: selftests: test skb->tstamp in redirect_neigh")
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20240120060518.3604920-2-martin.lau@linux.dev
BPF CI has been reporting the tc_redirect_dtime test failing
from time to time:
test_inet_dtime:PASS:setns src 0 nsec
(network_helpers.c:253: errno: No route to host) Failed to connect to server
close_netns:PASS:setns 0 nsec
test_inet_dtime:FAIL:connect_to_fd unexpected connect_to_fd: actual -1 < expected 0
test_tcp_clear_dtime:PASS:tcp ip6 clear dtime ingress_fwdns_p100 0 nsec
The connect_to_fd failure (EHOSTUNREACH) is from the
test_tcp_clear_dtime() test and it is the very first IPv6 traffic
after setting up all the links, addresses, and routes.
The symptom is this first connect() is always slow. In my setup, it
could take ~3s.
After some tracing and tcpdump, the slowness is mostly spent in
the neighbor solicitation in the "ns_fwd" namespace while
the "ns_src" and "ns_dst" are fine.
I forced the kernel to drop the neighbor solicitation messages.
I can then reproduce EHOSTUNREACH. What actually happen could be:
- the neighbor advertisement came back a little slow.
- the "ns_fwd" namespace concluded a neighbor discovery failure
and triggered the ndisc_error_report() => ip6_link_failure() =>
icmpv6_send(skb, ICMPV6_DEST_UNREACH, ICMPV6_ADDR_UNREACH, 0)
- the client's connect() reports EHOSTUNREACH after receiving
the ICMPV6_DEST_UNREACH message.
The neigh table of both "ns_src" and "ns_dst" namespace has already
been manually populated but not the "ns_fwd" namespace. This patch
fixes it by manually populating the neigh table also in the "ns_fwd"
namespace.
Although the namespace configuration part had been existed before
the tc_redirect_dtime test, still Fixes-tagging the patch when
the tc_redirect_dtime test was added since it is the only test
hitting it so far.
Fixes: c803475fd8 ("bpf: selftests: test skb->tstamp in redirect_neigh")
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20240120060518.3604920-1-martin.lau@linux.dev
This commit adds a sample selftest to demonstrate how we can use
bpf_sk_assign_tcp_reqsk() as the backend of SYN Proxy.
The test creates IPv4/IPv6 x TCP connections and transfer messages
over them on lo with BPF tc prog attached.
The tc prog will process SYN and returns SYN+ACK with the following
ISN and TS. In a real use case, this part will be done by other
hosts.
MSB LSB
ISN: | 31 ... 8 | 7 6 | 5 | 4 | 3 2 1 0 |
| Hash_1 | MSS | ECN | SACK | WScale |
TS: | 31 ... 8 | 7 ... 0 |
| Random | Hash_2 |
WScale in SYN is reused in SYN+ACK.
The client returns ACK, and tc prog will recalculate ISN and TS
from ACK and validate SYN Cookie.
If it's valid, the prog calls kfunc to allocate a reqsk for skb and
configure the reqsk based on the argument created from SYN Cookie.
Later, the reqsk will be processed in cookie_v[46]_check() to create
a connection.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20240115205514.68364-7-kuniyu@amazon.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
reviews.llvm.org was LLVM's Phabricator instances for code review. It
has been abandoned in favor of GitHub pull requests. While the majority
of links in the kernel sources still work because of the work Fangrui
has done turning the dynamic Phabricator instance into a static archive,
there are some issues with that work, so preemptively convert all the
links in the kernel sources to point to the commit on GitHub.
Most of the commits have the corresponding differential review link in
the commit message itself so there should not be any loss of fidelity in
the relevant information.
Additionally, fix a typo in the xdpwall.c print ("LLMV" -> "LLVM") while
in the area.
Link: https://discourse.llvm.org/t/update-on-github-pull-requests/71540/172
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20240111-bpf-update-llvm-phabricator-links-v2-1-9a7ae976bd64@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Various tests specify extra testing prog_flags when loading BPF
programs, like BPF_F_TEST_RND_HI32, and more recently also
BPF_F_TEST_REG_INVARIANTS. While BPF_F_TEST_RND_HI32 is old enough to
not cause much problem on older kernels, BPF_F_TEST_REG_INVARIANTS is
very fresh and unconditionally specifying it causes selftests to fail on
even slightly outdated kernels.
This breaks libbpf CI test against 4.9 and 5.15 kernels, it can break
some local development (done outside of VM), etc.
To prevent this, and guard against similar problems in the future, do
runtime detection of supported "testing flags", and only provide those
that host kernel recognizes.
Acked-by: Song Liu <song@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20240109231738.575844-1-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The test uses bpf_prog_get_info_by_fd() to obtain the xlated
instructions of the program first. Since these instructions have
already been rewritten by the verifier, the tests then checks whether
the rewritten instructions are as expected. And to ensure LLVM generates
code exactly as expected, use inline assembly and a naked function.
Suggested-by: Eduard Zingerman <eddyz87@gmail.com>
Signed-off-by: Hou Tao <houtao1@huawei.com>
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20240105104819.3916743-4-houtao@huaweicloud.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add feature detector of kernel-side arg:ctx (__arg_ctx) tag support. If
this is detected, libbpf will avoid doing any __arg_ctx-related BTF
rewriting and checks in favor of letting kernel handle this completely.
test_global_funcs/ctx_arg_rewrite subtest is adjusted to do the same
feature detection (albeit in much simpler, though round-about and
inefficient, way), and skip the tests. This is done to still be able to
execute this test on older kernels (like in libbpf CI).
Note, BPF token series ([0]) does a major refactor and code moving of
libbpf-internal feature detection "framework", so to avoid unnecessary
conflicts we keep newly added feature detection stand-alone with ad-hoc
result caching. Once things settle, there will be a small follow up to
re-integrate everything back and move code into its final place in
newly-added (by BPF token series) features.c file.
[0] https://patchwork.kernel.org/project/netdevbpf/list/?series=814209&state=*
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20240118033143.3384355-2-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The patch adds a test to exercise the bpf_iter_udp batching
logic. It specifically tests the case that there are multiple
so_reuseport udp_sk in a bucket of the udp_table.
The test creates two sets of so_reuseport sockets and
each set on a different port. Meaning there will be
two buckets in the udp_table.
The test does the following:
1. read() 3 out of 4 sockets in the first bucket.
2. close() all sockets in the first bucket. This
will ensure the current bucket's offset in
the kernel does not affect the read() of the
following bucket.
3. read() all 4 sockets in the second bucket.
The test also reads one udp_sk at a time from
the bpf_iter_udp prog. The true case in
"do_test(..., bool onebyone)". This is the buggy case
that the previous patch fixed.
It also tests the "false" case in "do_test(..., bool onebyone)",
meaning the userspace reads the whole bucket. There is
no bug in this case but adding this test also while
at it.
Considering the way to have multiple tcp_sk in the same
bucket is similar (by using so_reuseport),
this patch also tests the bpf_iter_tcp even though the
bpf_iter_tcp batching logic works correctly.
Both IP v4 and v6 are exercising the same bpf_iter batching
code path, so only v6 is tested.
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://lore.kernel.org/r/20240112190530.3751661-4-martin.lau@linux.dev
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
In the previous patch, the maximum data size for bpf_global_percpu_ma
is 512 bytes. This breaks selftest test_bpf_ma. The test is adjusted
in two aspects:
- Since the maximum allowed data size for bpf_global_percpu_ma is
512, remove all tests beyond that, names sizes 1024, 2048 and 4096.
- Previously the percpu data size is bucket_size - 8 in order to
avoid percpu allocation into the next bucket. This patch removed
such data size adjustment thanks to Patch 1.
Also, a better way to generate BTF type is used than adding
a member to the value struct.
Acked-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Yonghong Song <yonghong.song@linux.dev>
Link: https://lore.kernel.org/r/20231222031807.1292853-1-yonghong.song@linux.dev
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Daniel Borkmann says:
====================
bpf-next-for-netdev
The following pull-request contains BPF updates for your *net-next* tree.
We've added 22 non-merge commits during the last 3 day(s) which contain
a total of 23 files changed, 652 insertions(+), 431 deletions(-).
The main changes are:
1) Add verifier support for annotating user's global BPF subprogram arguments
with few commonly requested annotations for a better developer experience,
from Andrii Nakryiko.
These tags are:
- Ability to annotate a special PTR_TO_CTX argument
- Ability to annotate a generic PTR_TO_MEM as non-NULL
2) Support BPF verifier tracking of BPF_JNE which helps cases when the compiler
transforms (unsigned) "a > 0" into "if a == 0 goto xxx" and the like, from
Menglong Dong.
3) Fix a warning in bpf_mem_cache's check_obj_size() as reported by LKP, from Hou Tao.
4) Re-support uid/gid options when mounting bpffs which had to be reverted with
the prior token series revert to avoid conflicts, from Daniel Borkmann.
5) Fix a libbpf NULL pointer dereference in bpf_object__collect_prog_relos() found
from fuzzing the library with malformed ELF files, from Mingyi Zhang.
6) Skip DWARF sections in libbpf's linker sanity check given compiler options to
generate compressed debug sections can trigger a rejection due to misalignment,
from Alyssa Ross.
7) Fix an unnecessary use of the comma operator in BPF verifier, from Simon Horman.
8) Fix format specifier for unsigned long values in cpustat sample, from Colin Ian King.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test validating that freplace'ing another main (entry) BPF program
fails if the target BPF program doesn't have valid/expected func proto BTF.
We extend fexit_bpf2bpf test to allow to specify expected log message
for negative test cases (where freplace program is expected to fail to
load).
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20231215011334.2307144-11-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Instead of btf_check_subprog_arg_match(), use btf_prepare_func_args()
logic to validate "trustworthiness" of main BPF program's BTF information,
if it is present.
We ignored results of original BTF check anyway, often times producing
confusing and ominously-sounding "reg type unsupported for arg#0
function" message, which has no apparent effect on program correctness
and verification process.
All the -EFAULT returning sanity checks are already performed in
check_btf_info_early(), so there is zero reason to have this duplication
of logic between btf_check_subprog_call() and btf_check_subprog_arg_match().
Dropping btf_check_subprog_arg_match() simplifies
btf_check_func_arg_match() further removing `bool processing_call` flag.
One subtle bit that was done by btf_check_subprog_arg_match() was
potentially marking main program's BTF as unreliable. We do this
explicitly now with a dedicated simple check, preserving the original
behavior, but now based on well factored btf_prepare_func_args() logic.
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20231215011334.2307144-3-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The edge range checking for the registers is supported by the verifier
now, so we can activate the extended logic in
tools/testing/selftests/bpf/prog_tests/reg_bounds.c/range_cond() to test
such logic.
Besides, I added some cases to the "crafted_cases" array for this logic.
These cases are mainly used to test the edge of the src reg and dst reg.
All reg bounds testings has passed in the SLOW_TESTS mode:
$ export SLOW_TESTS=1 && ./test_progs -t reg_bounds -j
Summary: 65/18959832 PASSED, 0 SKIPPED, 0 FAILED
Signed-off-by: Menglong Dong <menglong8.dong@gmail.com>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20231219134800.1550388-4-menglong8.dong@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2023-12-18
This PR is larger than usual and contains changes in various parts
of the kernel.
The main changes are:
1) Fix kCFI bugs in BPF, from Peter Zijlstra.
End result: all forms of indirect calls from BPF into kernel
and from kernel into BPF work with CFI enabled. This allows BPF
to work with CONFIG_FINEIBT=y.
2) Introduce BPF token object, from Andrii Nakryiko.
It adds an ability to delegate a subset of BPF features from privileged
daemon (e.g., systemd) through special mount options for userns-bound
BPF FS to a trusted unprivileged application. The design accommodates
suggestions from Christian Brauner and Paul Moore.
Example:
$ sudo mkdir -p /sys/fs/bpf/token
$ sudo mount -t bpf bpffs /sys/fs/bpf/token \
-o delegate_cmds=prog_load:MAP_CREATE \
-o delegate_progs=kprobe \
-o delegate_attachs=xdp
3) Various verifier improvements and fixes, from Andrii Nakryiko, Andrei Matei.
- Complete precision tracking support for register spills
- Fix verification of possibly-zero-sized stack accesses
- Fix access to uninit stack slots
- Track aligned STACK_ZERO cases as imprecise spilled registers.
It improves the verifier "instructions processed" metric from single
digit to 50-60% for some programs.
- Fix verifier retval logic
4) Support for VLAN tag in XDP hints, from Larysa Zaremba.
5) Allocate BPF trampoline via bpf_prog_pack mechanism, from Song Liu.
End result: better memory utilization and lower I$ miss for calls to BPF
via BPF trampoline.
6) Fix race between BPF prog accessing inner map and parallel delete,
from Hou Tao.
7) Add bpf_xdp_get_xfrm_state() kfunc, from Daniel Xu.
It allows BPF interact with IPSEC infra. The intent is to support
software RSS (via XDP) for the upcoming ipsec pcpu work.
Experiments on AWS demonstrate single tunnel pcpu ipsec reaching
line rate on 100G ENA nics.
8) Expand bpf_cgrp_storage to support cgroup1 non-attach, from Yafang Shao.
9) BPF file verification via fsverity, from Song Liu.
It allows BPF progs get fsverity digest.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (164 commits)
bpf: Ensure precise is reset to false in __mark_reg_const_zero()
selftests/bpf: Add more uprobe multi fail tests
bpf: Fail uprobe multi link with negative offset
selftests/bpf: Test the release of map btf
s390/bpf: Fix indirect trampoline generation
selftests/bpf: Temporarily disable dummy_struct_ops test on s390
x86/cfi,bpf: Fix bpf_exception_cb() signature
bpf: Fix dtor CFI
cfi: Add CFI_NOSEAL()
x86/cfi,bpf: Fix bpf_struct_ops CFI
x86/cfi,bpf: Fix bpf_callback_t CFI
x86/cfi,bpf: Fix BPF JIT call
cfi: Flip headers
selftests/bpf: Add test for abnormal cnt during multi-kprobe attachment
selftests/bpf: Don't use libbpf_get_error() in kprobe_multi_test
selftests/bpf: Add test for abnormal cnt during multi-uprobe attachment
bpf: Limit the number of kprobes when attaching program to multiple kprobes
bpf: Limit the number of uprobes when attaching program to multiple uprobes
bpf: xdp: Register generic_kfunc_set with XDP programs
selftests/bpf: utilize string values for delegate_xxx mount options
...
====================
Link: https://lore.kernel.org/r/20231219000520.34178-1-alexei.starovoitov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When there is bpf_list_head or bpf_rb_root field in map value, the free
of map btf and the free of map value may run concurrently and there may
be use-after-free problem, so add two test cases to demonstrate it. And
the use-after-free problem can been easily reproduced by using bpf_next
tree and a KASAN-enabled kernel.
The first test case tests the racing between the free of map btf and the
free of array map. It constructs the racing by releasing the array map in
the end after other ref-counter of map btf has been released. To delay
the free of array map and make it be invoked after btf_free_rcu() is
invoked, it stresses system_unbound_wq by closing multiple percpu array
maps before it closes the array map.
The second case tests the racing between the free of map btf and the
free of inner map. Beside using the similar method as the first one
does, it uses bpf_map_delete_elem() to delete the inner map and to defer
the release of inner map after one RCU grace period.
The reason for using two skeletons is to prevent the release of outer
map and inner map in map_in_map_btf.c interfering the release of bpf
map in normal_map_btf.c.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Link: https://lore.kernel.org/bpf/20231216035510.4030605-1-houtao@huaweicloud.com
If an abnormally huge cnt is used for multi-kprobes attachment, the
following warning will be reported:
------------[ cut here ]------------
WARNING: CPU: 1 PID: 392 at mm/util.c:632 kvmalloc_node+0xd9/0xe0
Modules linked in: bpf_testmod(O)
CPU: 1 PID: 392 Comm: test_progs Tainted: G ...... 6.7.0-rc3+ #32
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996)
......
RIP: 0010:kvmalloc_node+0xd9/0xe0
? __warn+0x89/0x150
? kvmalloc_node+0xd9/0xe0
bpf_kprobe_multi_link_attach+0x87/0x670
__sys_bpf+0x2a28/0x2bc0
__x64_sys_bpf+0x1a/0x30
do_syscall_64+0x36/0xb0
entry_SYSCALL_64_after_hwframe+0x6e/0x76
RIP: 0033:0x7fbe067f0e0d
......
</TASK>
---[ end trace 0000000000000000 ]---
So add a test to ensure the warning is fixed.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20231215100708.2265609-6-houtao@huaweicloud.com
Since libbpf v1.0, libbpf doesn't return error code embedded into the
pointer iteself, libbpf_get_error() is deprecated and it is basically
the same as using -errno directly.
So replace the invocations of libbpf_get_error() by -errno in
kprobe_multi_test. For libbpf_get_error() in test_attach_api_fails(),
saving -errno before invoking ASSERT_xx() macros just in case that
errno is overwritten by these macros. However, the invocation of
libbpf_get_error() in get_syms() should be kept intact, because
hashmap__new() still returns a pointer with embedded error code.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20231215100708.2265609-5-houtao@huaweicloud.com
If an abnormally huge cnt is used for multi-uprobes attachment, the
following warning will be reported:
------------[ cut here ]------------
WARNING: CPU: 7 PID: 406 at mm/util.c:632 kvmalloc_node+0xd9/0xe0
Modules linked in: bpf_testmod(O)
CPU: 7 PID: 406 Comm: test_progs Tainted: G ...... 6.7.0-rc3+ #32
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996) ......
RIP: 0010:kvmalloc_node+0xd9/0xe0
......
Call Trace:
<TASK>
? __warn+0x89/0x150
? kvmalloc_node+0xd9/0xe0
bpf_uprobe_multi_link_attach+0x14a/0x480
__sys_bpf+0x14a9/0x2bc0
do_syscall_64+0x36/0xb0
entry_SYSCALL_64_after_hwframe+0x6e/0x76
......
</TASK>
---[ end trace 0000000000000000 ]---
So add a test to ensure the warning is fixed.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20231215100708.2265609-4-houtao@huaweicloud.com
With previous patch, one of subtests in test_btf_id becomes
flaky and may fail. The following is a failing example:
Error: #26 btf
Error: #26/174 btf/BTF ID
Error: #26/174 btf/BTF ID
btf_raw_create:PASS:check 0 nsec
btf_raw_create:PASS:check 0 nsec
test_btf_id:PASS:check 0 nsec
...
test_btf_id:PASS:check 0 nsec
test_btf_id:FAIL:check BTF lingersdo_test_get_info:FAIL:check failed: -1
The test tries to prove a btf_id not available after the map is closed.
But btf_id is freed only after workqueue and a rcu grace period, compared
to previous case just after a rcu grade period.
Depending on system workload, workqueue could take quite some time
to execute function bpf_map_free_deferred() which may cause the test failure.
Instead of adding arbitrary delays, let us remove the logic to
check btf_id availability after map is closed.
Signed-off-by: Yonghong Song <yonghong.song@linux.dev>
Link: https://lore.kernel.org/r/20231214203820.1469402-1-yonghong.song@linux.dev
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The easiest way to simulate stripped VLAN tag in veth is to send a packet
from VLAN interface, attached to veth. Unfortunately, this approach is
incompatible with AF_XDP on TX side, because VLAN interfaces do not have
such feature.
Check both packets sent via AF_XDP TX and regular socket.
AF_INET packet will also have a filled-in hash type (XDP_RSS_TYPE_L4),
unlike AF_XDP packet, so more values can be checked.
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Acked-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/r/20231205210847.28460-18-larysa.zaremba@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
We're observing test flakiness on an arm64 platform which might not
have timestamps as precise as x86. The test log looks like:
test_time_tai:PASS:tai_open 0 nsec
test_time_tai:PASS:test_run 0 nsec
test_time_tai:PASS:tai_ts1 0 nsec
test_time_tai:PASS:tai_ts2 0 nsec
test_time_tai:FAIL:tai_forward unexpected tai_forward: actual 1702348135471494160 <= expected 1702348135471494160
test_time_tai:PASS:tai_gettime 0 nsec
test_time_tai:PASS:tai_future_ts1 0 nsec
test_time_tai:PASS:tai_future_ts2 0 nsec
test_time_tai:PASS:tai_range_ts1 0 nsec
test_time_tai:PASS:tai_range_ts2 0 nsec
#199 time_tai:FAIL
This patch changes ASSERT_GT to ASSERT_GE in the tai_forward assertion
so that equal timestamps are permitted.
Fixes: 64e15820b9 ("selftests/bpf: Add BPF-helper test for CLOCK_TAI access")
Signed-off-by: YiFei Zhu <zhuyifei@google.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20231212182911.3784108-1-zhuyifei@google.com
Add selftest that establishes dead code-eliminated valid global subprog
(global_dead) and makes sure that it's not possible to freplace it, as
it's effectively not there. This test will fail with unexpected success
before 2afae08c9d ("bpf: Validate global subprogs lazily").
v2->v3:
- add missing err assignment (Alan);
- undo unnecessary signature changes in verifier_global_subprogs.c (Eduard);
v1->v2:
- don't rely on assembly output in verifier log, which changes between
compiler versions (CI).
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Reviewed-by: Alan Maguire <alan.maguire@oracle.com>
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/r/20231211174131.2324306-1-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
