[ Upstream commit ec449ed823 ]
Under high stress, SW steering might get stuck on polling for completion
that never comes.
For such cases QP needs to have protocol retransmission mechanism enabled.
Currently the retransmission timeout is defined as 0 (unlimited). Fix this
by defining a real timeout.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6cc64770fb ]
In line 849 (#1), "mlx5dr_htbl_put(cur_htbl);" drops the reference to
cur_htbl and may cause cur_htbl to be freed.
However, cur_htbl is subsequently used in the next line, which may result
in an use-after-free bug.
Fix this by calling mlx5dr_err() before the cur_htbl is put.
Signed-off-by: Wentao_Liang <Wentao_Liang_g@163.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a76b57311b ]
When P2P roc is removed, the IWL_MVM_STATUS_NEED_FLUSH_P2P bit is set
to indicate to iwl_mvm_roc_done_wk() that the removed roc is a P2P
one, so it will flush the broadcast station and not the aux station.
However, since setting this bit and scheduling the worker is done
in roc ended flow as well as in case the roc is removed, there is
a race where the worker has already started running (but did not
test this bit yet) and then it is scheduled again. In this case,
the first run of the worker will clear this bit, and thus the second
run will find it already cleared and will try to flush and remove
the aux station by mistake.
Fix it by scheduling the worker only if this bit is not yet set. In
case this bit is already set, the worker is either running or
scheduled, so there is no need to re-schedule it.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210819183728.8c147659b331.If5924375e9bfd46214ab8ab81cb9d0f5c82fbcbc@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6ce1c74ef ]
When TVQM is enabled (iwl_mvm_has_new_tx_api() is true), then
queue numbers are just sequentially assigned 0, 1, 2, ...
Prior to TVQM, in DQA, there were some statically allocated
queue numbers:
* IWL_MVM_DQA_AUX_QUEUE == 1,
* both IWL_MVM_DQA_INJECT_MONITOR_QUEUE and
IWL_MVM_DQA_P2P_DEVICE_QUEUE == 2, and
* IWL_MVM_DQA_AP_PROBE_RESP_QUEUE == 9.
Now, these values are assigned to the members mvm->aux_queue,
mvm->snif_queue, mvm->probe_queue and mvm->p2p_dev_queue by
default. Normally, this doesn't really matter, and if TVQM is
in fact available we override them to the real values after
allocating a queue for use there.
However, this allocation doesn't always happen. For example,
for mvm->p2p_dev_queue (== 2) it only happens when the P2P
Device interface is started, if any. If it's not started, the
value in mvm->p2p_dev_queue remains 2. This wouldn't really
matter all that much if it weren't for iwl_mvm_is_static_queue()
which checks a queue number against one of those four static
numbers.
Now, if no P2P Device or monitor interface is added then queue
2 may be dynamically allocated, yet alias mvm->p2p_dev_queue or
mvm->snif_queue, and thus iwl_mvm_is_static_queue() erroneously
returns true for it. If it then gets full, all interface queues
are stopped, instead of just backpressuring against the one TXQ
that's really the only affected one.
This clearly can lead to issues, as everything is stopped even
if just a single TXQ filled its corresponding HW queue, if it
happens to have an appropriate number (2 or 9, AUX is always
reassigned.) Due to a mac80211 bug, this also led to a situation
in which the queues remained stopped across a deauthentication
and then attempts to connect to a new AP started failing, but
that's fixed separately.
Fix all of this by simply initializing the queue numbers to
the invalid value until they're used, if TVQM is enabled, and
also setting them back to that value when the queues are later
freed again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802172232.2e47e623f9e2.I9b0830dafbb68ef35b7b8f0f46160abec02ac7d0@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f657f8eef3 ]
NFS implements blocking locks by blocking inside its lock method. In
the reexport case, this blocks the nfs server thread, which could lead
to deadlocks since an nfs server thread might be required to unlock the
conflicting lock. It also causes a crash, since the nfs server thread
assumes it can free the lock when its lm_notify lock callback is called.
Ideal would be to make the nfs lock method return without blocking in
this case, but for now it works just not to attempt blocking locks. The
difference is just that the original client will have to poll (as it
does in the v4.0 case) instead of getting a callback when the lock's
available.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Acked-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ec06c2dee ]
On systems with multiple SH per SE compute_static_thread_mgmt_se#
is split into independent masks, one for each SH, in the upper and
lower 16 bits. We need to detect this and apply cu masking to each
SH. The cu mask bits are assigned first to each SE, then to
alternate SHs, then finally to higher CU id. This ensures that
the maximum number of SPIs are engaged as early as possible while
balancing CU assignment to each SH.
v2: Use max SH/SE rather than max SH in cu_per_sh.
v3: Fix comment blocks, ensure se_mask is initially zero filled,
and correctly assign se.sh.cu positions to unset bits in cu_mask.
Signed-off-by: Sean Keely <Sean.Keely@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c75fc7193 ]
When more than one FE is connected to a BE, e.g. in a mixing use case,
the BE can be triggered multiple times when the FE are opened/started
concurrently. This race condition is problematic in the case of
SoundWire BE dailinks, and this is not desirable in a general
case. The code carefully checks when the BE can be stopped or
hw_free'ed, but the trigger code does not use any mutual exclusion.
Fix by using the same spinlock already used to check FE states, and
set the state before the trigger. In case of errors, the initial
state will be restored.
This patch does not change how the triggers are handled, it only makes
sure the states are handled in critical sections.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Message-Id: <20210817164054.250028-2-pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b873120995 ]
xhci-mtk depends on xhci's internal virt_dev when it retrieves its
internal data from usb_host_endpoint both in add_endpoint and
drop_endpoint callbacks. But when setup packet was retired by
transaction errors in xhci_setup_device() path, a virt_dev for the slot
is newly created with real_port 0. This leads to xhci-mtks's NULL pointer
dereference from drop_endpoint callback as xhci-mtk assumes that virt_dev's
real_port is always started from one. The similar problems were addressed
by [1] but that can't cover the failure cases from setup_device.
This patch drops the usages of xhci's virt_dev in xhci-mtk's drop_endpoint
callback by adopting rhashtable for searching mtk's schedule entity
from a given usb_host_endpoint pointer instead of searching a linked list.
So mtk's drop_endpoint callback doesn't have to rely on virt_dev at all.
[1] https://lore.kernel.org/r/1617179142-2681-2-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Link: https://lore.kernel.org/r/20210805133731.1.Icc0f080e75b1312692d4c7c7d25e7df9fe1a05c2@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66cce9e73e ]
When a remote usb device is attached to the local Virtual USB
Host Controller Root Hub port, the bound device driver may send
a port reset command.
vhci_hcd accepts port resets only when the device doesn't have
port address assigned to it. When reset happens device is in
assigned/used state and vhci_hcd rejects it leaving the port in
a stuck state.
This problem was found when a blue-tooth or xbox wireless dongle
was passed through using usbip.
A few drivers reset the port during probe including mt76 driver
specific to this bug report. Fix the problem with a change to
honor reset requests when device is in used state (VDEV_ST_USED).
Reported-and-tested-by: Michael <msbroadf@gmail.com>
Suggested-by: Michael <msbroadf@gmail.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210819225937.41037-1-skhan@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c75bde329 ]
If IRQ occurs between calling dsps_setup_optional_vbus_irq()
and dsps_create_musb_pdev(), then null pointer dereference occurs
since glue->musb wasn't initialized yet.
The patch puts initializing of neccesery data before registration
of the interrupt handler.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Link: https://lore.kernel.org/r/20210819163323.17714-1-lutovinova@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2847c46c61 ]
This reverts commit 5d5323a6f3.
That commit effectively disabled Intel host initiated U1/U2 lpm for devices
with periodic endpoints.
Before that commit we disabled host initiated U1/U2 lpm if the exit latency
was larger than any periodic endpoint service interval, this is according
to xhci spec xhci 1.1 specification section 4.23.5.2
After that commit we incorrectly checked that service interval was smaller
than U1/U2 inactivity timeout. This is not relevant, and can't happen for
Intel hosts as previously set U1/U2 timeout = 105% * service interval.
Patch claimed it solved cases where devices can't be enumerated because of
bandwidth issues. This might be true but it's a side effect of accidentally
turning off lpm.
exit latency calculations have been revised since then
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210820123503.2605901-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d72c74197b ]
smb_buf is allocated by small_smb_init_no_tc(), and buf type is
CIFS_SMALL_BUFFER, so we should use cifs_small_buf_release() to
release it in failed path.
Signed-off-by: Ding Hui <dinghui@sangfor.com.cn>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0e9422c4e ]
Currently, most pktgen samples print the execution result when the
program is terminated normally. However, sample03 doesn't work
appropriately.
This is results of samples:
# DEV=eth0 DEST_IP=10.1.0.1 DST_MAC=00:11:22:33:44:55 ./pktgen_sample04_many_flows.sh -n 1
Running... ctrl^C to stop
Device: eth0@0
Result: OK: 19(c5+d13) usec, 1 (60byte,0frags)
51762pps 24Mb/sec (24845760bps) errors: 0
# DEV=eth0 DEST_IP=10.1.0.1 DST_MAC=00:11:22:33:44:55 ./pktgen_sample03_burst_single_flow.sh -n 1
Running... ctrl^C to stop
The reason why it doesn't print the execution result when the program is
terminated usually is that sample03 doesn't call the function which
prints the result, unlike other samples.
So, this commit solves this issue by calling the function before
termination. Also, this commit changes control_c function to
print_result to maintain consistency with other samples.
Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 039190bb35 ]
Unlike OcteonTx2, the channel numbers used by CGX/RPM
and LBK on CN10K silicons aren't fixed in HW. They are
SW programmable, hence we cannot derive transmit link
from static channel numbers anymore. Get the same from
admin function via mailbox.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e72a55f2e5 ]
When a read/write command is sent via ioctl to the kernel,
and the command fails, the actual error response of the emmc
is not sent to the user.
IOCTL read/write tests are carried out using commands
17 (Single BLock Read), 24 (Single Block Write),
18 (Multi Block Read), 25 (Multi Block Write)
The tests are carried out on a 64Gb emmc device. All of these
tests try to access an "out of range" sector address (0x09B2FFFF).
It is seen that without the patch the response received by the user
is not OUT_OF_RANGE error (R1 response 31st bit is not set) as per
JEDEC specification. After applying the patch proper response is seen.
This is because the function returns without copying the response to
the user in case of failure. This patch fixes the issue.
Hence, this memcpy is required whether we get an error response or not.
Therefor it is moved up from the current position up to immediately
after we have called mmc_wait_for_req().
The test code and the output of only the CMD17 is included in the
commit to limit the message length.
CMD17 (Test Code Snippet):
==========================
printf("Forming CMD%d\n", opt_idx);
/* single block read */
cmd.blksz = 512;
cmd.blocks = 1;
cmd.write_flag = 0;
cmd.opcode = 17;
//cmd.arg = atoi(argv[3]);
cmd.arg = 0x09B2FFFF;
/* Expecting response R1B */
cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_ADTC;
memset(data, 0, sizeof(__u8) * 512);
mmc_ioc_cmd_set_data(cmd, data);
printf("Sending CMD%d: ARG[0x%08x]\n", opt_idx, cmd.arg);
if(ioctl(fd, MMC_IOC_CMD, &cmd))
perror("Error");
printf("\nResponse: %08x\n", cmd.response[0]);
CMD17 (Output without patch):
=============================
test@test-LIVA-Z:~$ sudo ./mmc cmd_test /dev/mmcblk0 17
Entering the do_mmc_commands:Device: /dev/mmcblk0 nargs:4
Entering the do_mmc_commands:Device: /dev/mmcblk0 options[17, 0x09B2FFF]
Forming CMD17
Sending CMD17: ARG[0x09b2ffff]
Error: Connection timed out
Response: 00000000
(Incorrect response)
CMD17 (Output with patch):
==========================
test@test-LIVA-Z:~$ sudo ./mmc cmd_test /dev/mmcblk0 17
[sudo] password for test:
Entering the do_mmc_commands:Device: /dev/mmcblk0 nargs:4
Entering the do_mmc_commands:Device: /dev/mmcblk0 options[17, 09B2FFFF]
Forming CMD17
Sending CMD17: ARG[0x09b2ffff]
Error: Connection timed out
Response: 80000900
(Correct OUT_OF_ERROR response as per JEDEC specification)
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20210824191726.8296-1-nishadkamdar@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d82d73da3 ]
0Day robot observed that it's easily timeout on a heavy load host.
-------------------
# selftests: bpf: test_maps
# Fork 1024 tasks to 'test_update_delete'
# Fork 1024 tasks to 'test_update_delete'
# Fork 100 tasks to 'test_hashmap'
# Fork 100 tasks to 'test_hashmap_percpu'
# Fork 100 tasks to 'test_hashmap_sizes'
# Fork 100 tasks to 'test_hashmap_walk'
# Fork 100 tasks to 'test_arraymap'
# Fork 100 tasks to 'test_arraymap_percpu'
# Failed sockmap unexpected timeout
not ok 3 selftests: bpf: test_maps # exit=1
# selftests: bpf: test_lru_map
# nr_cpus:8
-------------------
Since this test will be scheduled by 0Day to a random host that could have
only a few cpus(2-8), enlarge the timeout to avoid a false NG report.
In practice, i tried to pin it to only one cpu by 'taskset 0x01 ./test_maps',
and knew 10S is likely enough, but i still perfer to a larger value 30.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20210820015556.23276-2-lizhijian@cn.fujitsu.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ac5e45291 ]
For unexplained reasons, the prescaler register for this device needs to
be cleared (set to 1) while performing a data read or else the command
will hang. This does not appear to affect the real clock rate sent out
on the bus, so I assume it's purely to work around a hardware bug.
During normal operation, the prescaler is already set to 1, so nothing
needs to be done. However, in "initial mode" (which is used for sub-MHz
clock speeds, like the core sets while enumerating cards), it's set to
128 and so we need to reset it during data reads. We currently fail to
do this for long reads.
This has no functional affect on the driver's operation currently
written, as the MMC core always sets a clock above 1MHz before
attempting any long reads. However, the core could conceivably set any
clock speed at any time and the driver should still work, so I think
this fix is worthwhile.
I personally encountered this issue while performing data recovery on an
external chip. My connections had poor signal integrity, so I modified
the core code to reduce the clock speed. Without this change, I saw the
card enumerate but was unable to actually read any data.
Writes don't seem to work in the situation described above even with
this change (and even if the workaround is extended to encompass data
write commands). I was not able to find a way to get them working.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Link: https://lore.kernel.org/r/2fef280d8409ab0100c26c6ac7050227defd098d.1627818365.git.tommyhebb@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6966e6094c ]
When mmc_blk_card_busy() calls card_busy_detect() to poll for the card's
state with CMD13, this is done without any delays in between the commands
being sent.
Rather than fixing card_busy_detect() in this regards, let's instead
convert into using the common __mmc_poll_for_busy(), which also helps us to
avoid open-coding.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210702134229.357717-4-ulf.hansson@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 468108155b ]
When __mmc_blk_ioctl_cmd() calls card_busy_detect() to verify that the
card's states moves back into transfer state, the polling with CMD13 is
done without any delays in between the commands being sent.
Rather than fixing card_busy_detect() in this regards, let's instead
convert into using the common mmc_poll_for_busy(), which also helps us to
avoid open-coding.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210702134229.357717-3-ulf.hansson@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 972d508483 ]
When mmc_blk_fix_state() sends a CMD12 to try to move the card into the
transfer state, it calls card_busy_detect() to poll for the card's state
with CMD13. This is done without any delays in between the commands being
sent.
Rather than fixing card_busy_detect() in this regards, let's instead
convert into using the common mmc_poll_for_busy(), which also helps us to
avoid open-coding.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210702134229.357717-2-ulf.hansson@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6211e9cb2f ]
Trying to boot without SYSFS, but with OF_DYNAMIC quickly
results in a crash:
[ 0.088460] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000070
[...]
[ 0.103927] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 5.14.0-rc3 #4179
[ 0.105810] Hardware name: linux,dummy-virt (DT)
[ 0.107147] pstate: 80000005 (Nzcv daif -PAN -UAO -TCO BTYPE=--)
[ 0.108876] pc : kernfs_find_and_get_ns+0x3c/0x7c
[ 0.110244] lr : kernfs_find_and_get_ns+0x3c/0x7c
[...]
[ 0.134087] Call trace:
[ 0.134800] kernfs_find_and_get_ns+0x3c/0x7c
[ 0.136054] safe_name+0x4c/0xd0
[ 0.136994] __of_attach_node_sysfs+0xf8/0x124
[ 0.138287] of_core_init+0x90/0xfc
[ 0.139296] driver_init+0x30/0x4c
[ 0.140283] kernel_init_freeable+0x160/0x1b8
[ 0.141543] kernel_init+0x30/0x140
[ 0.142561] ret_from_fork+0x10/0x18
While not having sysfs isn't a very common option these days,
it is still expected that such configuration would work.
Paper over it by bailing out from __of_attach_node_sysfs() if
CONFIG_SYSFS isn't enabled.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210820144722.169226-1-maz@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3736127a3a ]
Function btrfs_lookup_data_extent calls btrfs_search_slot to verify if
the EXTENT_ITEM exists in the extent tree. btrfs_search_slot can return
values bellow zero if an error happened.
Function replay_one_extent currently checks if the search found
something (0 returned) and increments the reference, and if not, it
seems to evaluate as 'not found'.
Fix the condition by checking if the value was bellow zero and return
early.
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Marcos Paulo de Souza <mpdesouza@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cceaa89f02 ]
When using the NO_HOLES feature and expanding the size of an inode, we
update the inode's last_trans, last_sub_trans and last_log_commit fields
at maybe_insert_hole() so that a fsync does know that the inode needs to
be logged (by making sure that btrfs_inode_in_log() returns false). This
happens for expanding truncate operations, buffered writes, direct IO
writes and when cloning extents to an offset greater than the inode's
i_size.
However the way we do it is racy, because in between setting the inode's
last_sub_trans and last_log_commit fields, the log transaction ID that was
assigned to last_sub_trans might be committed before we read the root's
last_log_commit and assign that value to last_log_commit. If that happens
it would make a future call to btrfs_inode_in_log() return true. This is
a race that should be extremely unlikely to be hit in practice, and it is
the same that was described by commit bc0939fcfa ("btrfs: fix race
between marking inode needs to be logged and log syncing").
The fix would simply be to set last_log_commit to the value we assigned
to last_sub_trans minus 1, like it was done in that commit. However
updating these two fields plus the last_trans field is pointless here
because all the callers of btrfs_cont_expand() (which is the only
caller of maybe_insert_hole()) always call btrfs_set_inode_last_trans()
or btrfs_update_inode() after calling btrfs_cont_expand(). Calling either
btrfs_set_inode_last_trans() or btrfs_update_inode() guarantees that the
next fsync will log the inode, as it makes btrfs_inode_in_log() return
false.
So just remove the code that explicitly sets the inode's last_trans,
last_sub_trans and last_log_commit fields.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db87db65c1 ]
> Hi Arnd,
>
> First bad commit (maybe != root cause):
>
> tree: https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git master
> head: 2f73937c9aa561e2082839bc1a8efaac75d6e244
> commit: 47fd22f2b8 [4771/5318] cs89x0: rework driver configuration
> config: m68k-randconfig-c003-20210804 (attached as .config)
> compiler: m68k-linux-gcc (GCC) 10.3.0
> reproduce (this is a W=1 build):
> wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
> chmod +x ~/bin/make.cross
> # https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/?id=47fd22f2b84765a2f7e3f150282497b902624547
> git remote add linux-next https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git
> git fetch --no-tags linux-next master
> git checkout 47fd22f2b8
> # save the attached .config to linux build tree
> COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-10.3.0 make.cross ARCH=m68k
>
> If you fix the issue, kindly add following tag as appropriate
> Reported-by: kernel test robot <lkp@intel.com>
>
> All errors (new ones prefixed by >>):
>
> In file included from include/linux/kernel.h:19,
> from include/linux/list.h:9,
> from include/linux/module.h:12,
> from drivers/net/ethernet/cirrus/cs89x0.c:51:
> drivers/net/ethernet/cirrus/cs89x0.c: In function 'net_open':
> drivers/net/ethernet/cirrus/cs89x0.c:897:20: error: implicit declaration of function 'isa_virt_to_bus'; did you mean 'virt_to_bus'? [-Werror=implicit-function-declaration]
> 897 | (unsigned long)isa_virt_to_bus(lp->dma_buff));
> | ^~~~~~~~~~~~~~~
> include/linux/printk.h:141:17: note: in definition of macro 'no_printk'
> 141 | printk(fmt, ##__VA_ARGS__); \
> | ^~~~~~~~~~~
> drivers/net/ethernet/cirrus/cs89x0.c:86:3: note: in expansion of macro 'pr_debug'
> 86 | pr_##level(fmt, ##__VA_ARGS__); \
> | ^~~
> drivers/net/ethernet/cirrus/cs89x0.c:894:3: note: in expansion of macro 'cs89_dbg'
> 894 | cs89_dbg(1, debug, "%s: dma %lx %lx\n",
> | ^~~~~~~~
> >> drivers/net/ethernet/cirrus/cs89x0.c:914:3: error: implicit declaration of function 'disable_dma'; did you mean 'disable_irq'? [-Werror=implicit-function-declaration]
As far as I can tell, this is a bug with the m68kmmu architecture, not
with my driver:
The CONFIG_ISA_DMA_API option is provided for coldfire, which implements it,
but dragonball also sets the option as a side-effect, without actually
implementing
the interfaces. The patch below should fix it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8fb4df1f5 ]
'bp_ena' in Aura context is NIX block index, setting it
zero will always backpressure NIX0 block, even if NIXLF
belongs to NIX1. Hence fix this by setting it appropriately
based on NIX block address.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05e4588738 ]
The kernel test robot reports undefined reference after we report wakeup
reason to mac80211. This is because CONFIG_PM is not defined in the testing
configuration file. In fact, functions within wow.c are used if CONFIG_PM
is defined, so use CONFIG_PM to decide whether we build this file or not.
The reported messages are:
hppa-linux-ld: drivers/net/wireless/realtek/rtw88/wow.o: in function `rtw_wow_show_wakeup_reason':
>> (.text+0x6c4): undefined reference to `ieee80211_report_wowlan_wakeup'
>> hppa-linux-ld: (.text+0x6e0): undefined reference to `ieee80211_report_wowlan_wakeup'
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210728014335.8785-4-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02a55c0009 ]
In current wow flow, driver calls rtw_wow_fw_start and sleep for 100ms,
to wait firmware finish preliminary work and then update the value of
WOWLAN_WAKE_REASON register to zero. But later firmware will start wow
function with power-saving mode, in which mode the value of
WOWLAN_WAKE_REASON register is 0xea. So driver may get 0xea value and
return fail. We use read_poll_timeout instead to check the value to avoid
this issue.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210728014335.8785-2-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
