Pull SoC driver updates from Arnd Bergmann:
"Nothing particular important in the SoC driver updates, just the usual
improvements to for drivers/soc and a couple of subsystems that don't
fit anywhere else:
- The largest set of updates is for Qualcomm SoC drivers, extending
the set of supported features for additional SoCs in the QSEECOM,
LLCC and socinfo drivers.a
- The ti_sci firmware driver gains support for power managment
- The drivers/reset subsystem sees a rework of the microchip sparx5
and amlogic reset drivers to support additional chips, plus a few
minor updates on other platforms
- The SCMI firmware interface driver gains support for two protocol
extensions, allowing more flexible use of the shared memory area
and new DT binding properties for configurability.
- Mediatek SoC drivers gain support for power managment on the MT8188
SoC and a new driver for DVFS.
- The AMD/Xilinx ZynqMP SoC drivers gain support for system reboot
and a few bugfixes
- The Hisilicon Kunpeng HCCS driver gains support for configuring
lanes through sysfs
Finally, there are cleanups and minor fixes for drivers/{soc, bus,
memory}, including changing back the .remove_new callback to .remove,
as well as a few other updates for freescale (powerpc) soc drivers,
NXP i.MX soc drivers, cznic turris platform driver, memory controller
drviers, TI OMAP SoC drivers, and Tegra firmware drivers"
* tag 'soc-drivers-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (116 commits)
soc: fsl: cpm1: qmc: Set the ret error code on platform_get_irq() failure
soc: fsl: rcpm: fix missing of_node_put() in copy_ippdexpcr1_setting()
soc: fsl: cpm1: tsa: switch to for_each_available_child_of_node_scoped()
platform: cznic: turris-omnia-mcu: Rename variable holding GPIO line names
platform: cznic: turris-omnia-mcu: Document the driver private data structure
firmware: turris-mox-rwtm: Document the driver private data structure
bus: Switch back to struct platform_driver::remove()
soc: qcom: ice: Remove the device_link field in qcom_ice
drm/msm/adreno: Setup SMMU aparture for per-process page table
firmware: qcom: scm: Introduce CP_SMMU_APERTURE_ID
firmware: arm_scpi: Check the DVFS OPP count returned by the firmware
soc: qcom: socinfo: add IPQ5424/IPQ5404 SoC ID
dt-bindings: arm: qcom,ids: add SoC ID for IPQ5424/IPQ5404
soc: qcom: llcc: Flip the manual slice configuration condition
dt-bindings: firmware: qcom,scm: Document sm8750 SCM
firmware: qcom: uefisecapp: Allow X1E Devkit devices
misc: lan966x_pci: Fix dtc warn 'Missing interrupt-parent'
misc: lan966x_pci: Fix dtc warns 'missing or empty reg/ranges property'
soc: qcom: llcc: Add LLCC configuration for the QCS8300 platform
dt-bindings: cache: qcom,llcc: Document the QCS8300 LLCC
...
The QCOM_SCM_SVC_MP service provides QCOM_SCM_MP_CP_SMMU_APERTURE_ID,
which is used to trigger the mapping of register banks into the SMMU
context for per-processes page tables to function (in case this isn't
statically setup by firmware).
This is necessary on e.g. QCS6490 Rb3Gen2, in order to avoid "CP | AHB
bus error"-errors from the GPU.
Introduce a function to allow the msm driver to invoke this call.
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Link: https://lore.kernel.org/r/20241110-adreno-smmu-aparture-v2-1-9b1fb2ee41d4@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
When enabling SHM bridge, QTEE returns 0 and sets error 4 in result to
qcom_scm for unsupported platforms. Currently, tzmem interprets this as
an unknown error rather than recognizing it as an unsupported platform.
Error log:
[ 0.177224] qcom_scm firmware:scm: error (____ptrval____): Failed to enable the TrustZone memory allocator
[ 0.177244] qcom_scm firmware:scm: probe with driver qcom_scm failed with error 4
To address this, modify the function call qcom_scm_shm_bridge_enable()
to remap result to indicate an unsupported error. This way, tzmem will
correctly identify it as an unsupported platform case instead of
reporting it as an error.
Fixes: 178e19c0df ("firmware: qcom: scm: add support for SHM bridge operations")
Signed-off-by: Qingqing Zhou <quic_qqzhou@quicinc.com>
Co-developed-by: Kuldeep Singh <quic_kuldsing@quicinc.com>
Signed-off-by: Kuldeep Singh <quic_kuldsing@quicinc.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>
Link: https://lore.kernel.org/r/20241022192148.1626633-1-quic_kuldsing@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Stop spamming the logs with errors about missing mechanism for setting
the so called download (or dump) mode for users that have not requested
that feature to be enabled in the first place.
This avoids the follow error being logged on boot as well as on
shutdown when the feature it not available and download mode has not
been enabled on the kernel command line:
qcom_scm firmware:scm: No available mechanism for setting download mode
Fixes: 79cb2cb8d8 ("firmware: qcom: scm: Disable SDI and write no dump to dump mode")
Fixes: 781d32d1c9 ("firmware: qcom_scm: Clear download bit during reboot")
Cc: Mukesh Ojha <quic_mojha@quicinc.com>
Cc: stable@vger.kernel.org # 6.4
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>
Link: https://lore.kernel.org/r/20241002100122.18809-2-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Pull SoC driver updates from Arnd Bergmann:
"The driver updates seem larger this time around, with changes is many
of the SoC specific drivers, both the custom drivers/soc ones and the
closely related subsystems (memory, bus, firmware, reset, ...).
The at91 platform gains support for sam9x7 chips in the soc and power
management code. This is the latest variant of one of the oldest still
supported SoC families, using the ARM9 (ARMv5) core.
As usual, the qualcomm snapdragon platform gets a ton of updates in
many of their drivers to add more features and additional SoC support.
Most of these are somewhat firmware related as the platform has a
number of firmware based interfaces to the kernel. A notable addition
here is the inclusion of trace events to two of these drivers.
Herve Codina and Christophe Leroy are now sending updates for
drivers/soc/fsl/ code through the SoC tree, this contains both PowerPC
and Arm specific platforms and has previously been problematic to
maintain. The first update here contains support for newer PowerPC
variants and some cleanups.
The turris mox firmware driver has a number of updates, mostly
cleanups.
The Arm SCMI firmware driver gets a major rework to modularize the
existing code into separately loadable drivers for the various
transports, the addition of custom NXP i.MX9 interfaces and a number
of smaller updates.
The Arm FF-A firmware driver gets a feature update to support the v1.2
version of the specification.
The reset controller drivers have some smaller cleanups and a newly
added driver for the Intel/Mobileye EyeQ5/EyeQ6 MIPS SoCs.
The memory controller drivers get some cleanups and refactoring for
Tegra, TI, Freescale/NXP and a couple more platforms.
Finally there are lots of minor updates to firmware (raspberry pi,
tegra, imx), bus (sunxi, omap, tegra) and soc (rockchips, tegra,
amlogic, mediatek) drivers and their DT bindings"
* tag 'soc-drivers-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (212 commits)
firmware: imx: remove duplicate scmi_imx_misc_ctrl_get()
platform: cznic: turris-omnia-mcu: Fix error check in omnia_mcu_register_trng()
bus: sunxi-rsb: Simplify code with dev_err_probe()
soc: fsl: qe: ucc: Export ucc_mux_set_grant_tsa_bkpt
soc: fsl: cpm1: qmc: Fix dependency on fsl_soc.h
dt-bindings: arm: rockchip: Add rk3576 compatible string to pmu.yaml
soc: fsl: qbman: Remove redundant warnings
soc: fsl: qbman: Use iommu_paging_domain_alloc()
MAINTAINERS: Add QE files related to the Freescale QMC controller
soc: fsl: cpm1: qmc: Handle QUICC Engine (QE) soft-qmc firmware
soc: fsl: cpm1: qmc: Add support for QUICC Engine (QE) implementation
soc: fsl: qe: Add missing PUSHSCHED command
soc: fsl: qe: Add resource-managed muram allocators
soc: fsl: cpm1: qmc: Introduce qmc_version
soc: fsl: cpm1: qmc: Rename SCC_GSMRL_MODE_QMC
soc: fsl: cpm1: qmc: Handle RPACK initialization
soc: fsl: cpm1: qmc: Rename qmc_chan_command()
soc: fsl: cpm1: qmc: Introduce qmc_{init,exit}_xcc() and their CPM1 version
soc: fsl: cpm1: qmc: Introduce qmc_init_resource() and its CPM1 version
soc: fsl: cpm1: qmc: Re-order probe() operations
...
Currently on Qualcomm SoC, download_mode is enabled if
CONFIG_QCOM_SCM_DOWNLOAD_MODE_DEFAULT is selected or
passed a boolean value from command line.
Refactor the code such that it supports multiple download
modes and drop CONFIG_QCOM_SCM_DOWNLOAD_MODE_DEFAULT config
instead, give interface to set the download mode from
module parameter while being backword compatible at the
same time.
Signed-off-by: Mukesh Ojha <quic_mojha@quicinc.com>
Link: https://lore.kernel.org/r/20240715155655.1811178-1-quic_mojha@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Currently get_wq_ctx() is wrongly configured as a standard call. When two
SMC calls are in sleep and one SMC wakes up, it calls get_wq_ctx() to
resume the corresponding sleeping thread. But if get_wq_ctx() is
interrupted, goes to sleep and another SMC call is waiting to be allocated
a waitq context, it leads to a deadlock.
To avoid this get_wq_ctx() must be an atomic call and can't be a standard
SMC call. Hence mark get_wq_ctx() as a fast call.
Fixes: 6bf3259922 ("firmware: qcom: scm: Add wait-queue handling logic")
Cc: stable@vger.kernel.org
Signed-off-by: Murali Nalajala <quic_mnalajal@quicinc.com>
Signed-off-by: Unnathi Chalicheemala <quic_uchalich@quicinc.com>
Reviewed-by: Elliot Berman <quic_eberman@quicinc.com>
Link: https://lore.kernel.org/r/20240814223244.40081-1-quic_uchalich@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
SDI is enabled for most of the Qualcomm SoCs and as per commit
ff4aa3bc98 ("firmware: qcom_scm: disable SDI if required")
it was recommended to disable SDI by mentioning it in device tree
to avoid hang during watchdog or during reboot.
However, for some cases if download mode tcsr register already
configured from boot firmware to collect dumps and if SDI is
disabled via means of mentioning it in device tree we could
still end up with dump collection. Disabling SDI alone is
not completely enough to disable dump mode and we also need to
zero out the bits download bits from tcsr register.
Current commit now, unconditionally call qcom_scm_set_download_mode()
based on download_mode flag, at max if TCSR register is not mentioned
or available for a SoC it will fallback to legacy way of setting
download mode through command which may be no-ops or return error
in case current firmware does not implements QCOM_SCM_INFO_IS_CALL_AVAIL
so, at worst it does nothing if it fails.
It also does to call SDI disable call if dload mode is disabled, which
looks fine to do as intention is to disable dump collection even if
system crashes.
Fixes: ff4aa3bc98 ("firmware: qcom_scm: disable SDI if required")
Signed-off-by: Mukesh Ojha <quic_mojha@quicinc.com>
Link: https://lore.kernel.org/r/20240708155332.4056479-1-quic_mojha@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
SHM Bridge is a safety mechanism allowing to limit the amount of memory
shared between the kernel and the TrustZone to regions explicitly marked
as such.
Add a variant of the tzmem allocator that configures the memory pools as
SHM bridges. It also enables the SHM bridge globally so non-SHM bridge
memory will no longer work with SCM calls.
If enabled at build-time, it will still be checked for availability at
run-time. If the architecture doesn't support SHM Bridge, the allocator
will fall back to the generic mode.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sc8280xp-lenovo-thinkpad-x13s
Tested-by: Deepti Jaggi <quic_djaggi@quicinc.com> #sa8775p-ride
Reviewed-by: Elliot Berman <quic_eberman@quicinc.com>
Link: https://lore.kernel.org/r/20240527-shm-bridge-v10-11-ce7afaa58d3a@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
We need to allocate, map and pass a buffer to the trustzone if we have
more than 4 arguments for a given SCM call. Let's use the new TrustZone
allocator for that memory and shrink the code in process.
As this code lives in a different compilation unit than the rest of the
SCM code, we need to provide a helper in the form of
qcom_scm_get_tzmem_pool() that allows the SMC low-level routines to
access the SCM memory pool.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sc8280xp-lenovo-thinkpad-x13s
Tested-by: Deepti Jaggi <quic_djaggi@quicinc.com> #sa8775p-ride
Reviewed-by: Elliot Berman <quic_eberman@quicinc.com>
Link: https://lore.kernel.org/r/20240527-shm-bridge-v10-4-ce7afaa58d3a@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Select the TrustZone memory allocator in Kconfig and create a pool of
memory shareable with the TrustZone when probing the SCM driver.
This will allow a gradual conversion of all relevant SCM calls to using
the dedicated allocator.
The policy used for the pool is "on-demand" and the initial size is 0
as - depending on the config - it's possible that no SCM calls needing
to allocate memory will be called. The sizes of possible allocations also
vary substiantially further warranting the "on-demand" approach.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sc8280xp-lenovo-thinkpad-x13s
Tested-by: Deepti Jaggi <quic_djaggi@quicinc.com> #sa8775p-ride
Reviewed-by: Elliot Berman <quic_eberman@quicinc.com>
Link: https://lore.kernel.org/r/20240527-shm-bridge-v10-3-ce7afaa58d3a@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
We have several SCM calls that require passing buffers to the TrustZone
on top of the SMC core which allocates memory for calls that require
more than 4 arguments.
Currently every user does their own thing which leads to code
duplication. Many users call dma_alloc_coherent() for every call which
is terribly unperformant (speed- and size-wise).
Provide a set of library functions for creating and managing pools of
memory which is suitable for sharing with the TrustZone, that is:
page-aligned, contiguous and non-cachable as well as provides a way of
mapping of kernel virtual addresses to physical space.
Make the allocator ready for extending with additional modes of operation
which will allow us to support the SHM bridge safety mechanism once all
users convert.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sc8280xp-lenovo-thinkpad-x13s
Tested-by: Deepti Jaggi <quic_djaggi@quicinc.com> #sa8775p-ride
Reviewed-by: Elliot Berman <quic_eberman@quicinc.com>
Link: https://lore.kernel.org/r/20240527-shm-bridge-v10-2-ce7afaa58d3a@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Pull SoC driver updates from Arnd Bergmann:
"As usual, these are updates for drivers that are specific to certain
SoCs or firmware running on them.
Notable updates include
- The new STMicroelectronics STM32 "firewall" bus driver that is used
to provide a barrier between different parts of an SoC
- Lots of updates for the Qualcomm platform drivers, in particular
SCM, which gets a rewrite of its initialization code
- Firmware driver updates for Arm FF-A notification interrupts and
indirect messaging, SCMI firmware support for pin control and
vendor specific interfaces, and TEE firmware interface changes
across multiple TEE drivers
- A larger cleanup of the Mediatek CMDQ driver and some related bits
- Kconfig changes for riscv drivers to prepare for adding Kanaan k230
support
- Multiple minor updates for the TI sysc bus driver, memory
controllers, hisilicon hccs and more"
* tag 'soc-drivers-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (103 commits)
firmware: qcom: uefisecapp: Allow on sc8180x Primus and Flex 5G
soc: qcom: pmic_glink: Make client-lock non-sleeping
dt-bindings: soc: qcom,wcnss: fix bluetooth address example
soc/tegra: pmc: Add EQOS wake event for Tegra194 and Tegra234
bus: stm32_firewall: fix off by one in stm32_firewall_get_firewall()
bus: etzpc: introduce ETZPC firewall controller driver
firmware: arm_ffa: Avoid queuing work when running on the worker queue
bus: ti-sysc: Drop legacy idle quirk handling
bus: ti-sysc: Drop legacy quirk handling for smartreflex
bus: ti-sysc: Drop legacy quirk handling for uarts
bus: ti-sysc: Add a description and copyrights
bus: ti-sysc: Move check for no-reset-on-init
soc: hisilicon: kunpeng_hccs: replace MAILBOX dependency with PCC
soc: hisilicon: kunpeng_hccs: Add the check for obtaining complete port attribute
firmware: arm_ffa: Fix memory corruption in ffa_msg_send2()
bus: rifsc: introduce RIFSC firewall controller driver
of: property: fw_devlink: Add support for "access-controller"
soc: mediatek: mtk-socinfo: Correct the marketing name for MT8188GV
soc: mediatek: mtk-socinfo: Add entry for MT8395AV/ZA Genio 1200
soc: mediatek: mtk-mutex: Add support for MT8188 VPPSYS
...
It is possible qcom_scm_is_available() gives wrong indication that
if __scm is initialized while __scm->dev is not and similar issue
is also possible with __scm->waitq_comp.
Fix this appropriately by the use of release barrier and read barrier
that will make sure if __scm is initialized so, is all of its field
variable.
Fixes: d0f6fa7ba2 ("firmware: qcom: scm: Convert SCM to platform driver")
Fixes: 6bf3259922 ("firmware: qcom: scm: Add wait-queue handling logic")
Signed-off-by: Mukesh Ojha <quic_mojha@quicinc.com>
Link: https://lore.kernel.org/r/1711034642-22860-4-git-send-email-quic_mojha@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
QCOM_SCM_BOOT_SET_DLOAD_MODE scm command is applicable for very
older SoCs where this command is supported from firmware and
for newer SoCs, dload mode tcsr registers is used for setting
the download mode.
Currently, qcom_scm_set_download_mode() checks for availability
of QCOM_SCM_BOOT_SET_DLOAD_MODE command even for SoCs where this
is not used. Fix this by switching the condition to keep the
command availability check only if dload mode registers are not
available.
Signed-off-by: Mukesh Ojha <quic_mojha@quicinc.com>
Reviewed-by: Elliot Berman <quic_eberman@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/1711034642-22860-3-git-send-email-quic_mojha@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
It turns out that while the QSEECOM APP_SEND command has specific fields
for request and response buffers, uefisecapp expects them both to be in
a single memory region. Failure to adhere to this has (so far) resulted
in either no response being written to the response buffer (causing an
EIO to be emitted down the line), the SCM call to fail with EINVAL
(i.e., directly from TZ/firmware), or the device to be hard-reset.
While this issue can be triggered deterministically, in the current form
it seems to happen rather sporadically (which is why it has gone
unnoticed during earlier testing). This is likely due to the two
kzalloc() calls (for request and response) being directly after each
other. Which means that those likely return consecutive regions most of
the time, especially when not much else is going on in the system.
Fix this by allocating a single memory region for both request and
response buffers, properly aligning both structs inside it. This
unfortunately also means that the qcom_scm_qseecom_app_send() interface
needs to be restructured, as it should no longer map the DMA regions
separately. Therefore, move the responsibility of DMA allocation (or
mapping) to the caller.
Fixes: 759e7a2b62 ("firmware: Add support for Qualcomm UEFI Secure Application")
Cc: stable@vger.kernel.org # 6.7
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Tested-by: Konrad Dybcio <konrad.dybcio@linaro.org> # X13s
Link: https://lore.kernel.org/r/20240406130125.1047436-1-luzmaximilian@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
