[ Upstream commit f42ae7b054 ]
The USB hub port-number range for USB 2.0 is 1-255 and not 1-31 which
reflects an arbitrary limit set by the current Linux implementation.
Note that for USB 3.1 hubs the valid range is 1-15.
Increase the documented valid range in the binding to 255, which is the
maximum allowed by the specifications.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68615eb01f upstream.
With a nxp,se97 chip on an atmel sama5d31 board, the I2C adapter driver
is not always capable of avoiding the 25-35 ms timeout as specified by
the SMBUS protocol. This may cause silent corruption of the last bit of
any transfer, e.g. a one is read instead of a zero if the sensor chip
times out. This also affects the eeprom half of the nxp-se97 chip, where
this silent corruption was originally noticed. Other I2C adapters probably
suffer similar issues, e.g. bit-banging comes to mind as risky...
The SMBUS register in the nxp chip is not a standard Jedec register, but
it is not special to the nxp chips either, at least the atmel chips
have the same mechanism. Therefore, do not special case this on the
manufacturer, it is opt-in via the device property anyway.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 729e55225b ]
This erratum describes a bug in logic outside the core, so MIDR can't be
used to identify its presence, and reading an SoC-specific revision
register from common arch timer code would be awkward. So, describe it
in the device tree.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 34c55cf2fc ]
Currently dp83867 driver returns error if phy interface type
PHY_INTERFACE_MODE_RGMII_RXID is used to set the rx only internal
delay. Similarly issue happens for PHY_INTERFACE_MODE_RGMII_TXID.
Fix this by checking also the interface type if a particular delay
value is missing in the phy dt bindings. Also update the DT document
accordingly.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 61976fff20 ]
When the binding was defined, I was not aware that mt2701 was an earlier
version of the SoC. For sake of consistency, the ethernet driver should
use mt2701 inside the compat string as this is the earliest SoC with the
ethernet core.
The ethernet driver is currently of no real use until we finish and
upstream the DSA driver. There are no users of this binding yet. It should
be safe to fix this now before it is too late and we need to provide
backward compatibility for the mt7623-eth compat string.
Reported-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: John Crispin <john@phrozen.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 308d3165d8 ]
The patches regarding eee-broken-modes was merged before all people
involved could find an agreement on the best way to move forward.
While we agreed on having a DT property to mark particular modes as broken,
the value used for eee-broken-modes mapped the phy register in very direct
way. Because of this, the concern is that it could be used to implement
configuration policies instead of describing a broken HW.
In the end, having a boolean property for each mode seems to be preferred
over one bit field value mapping the register (too) directly.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0b445549ea ]
In soft (no-reboot) mode, the driver self-pings watchdog upon expiration
of an interrupt. However the interrupt itself was not cleared thus on
first hit, the system enters infinite interrupt handling loop.
On Odroid U3 (Exynos4412), when booted with s3c2410_wdt.soft_noboot=1
argument the console is flooded:
# killall -9 watchdog
[ 60.523760] s3c2410-wdt 10060000.watchdog: watchdog timer expired (irq)
[ 60.536744] s3c2410-wdt 10060000.watchdog: watchdog timer expired (irq)
Fix this by writing something to the WTCLRINT register to clear the
interrupt. The register WTCLRINT however appeared in S3C6410 so a new
watchdog quirk and flavor are needed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d8ec7595a0 ]
The ARM specifies that the system counter "must be implemented in an
always-on power domain," and so we try to use the counter as a source of
timekeeping across suspend/resume. Unfortunately, some SoCs (e.g.,
Rockchip's RK3399) do not keep the counter ticking properly when
switched from their high-power clock to the lower-power clock used in
system suspend. Support this quirk by adding a new device tree property.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93a5ec14da upstream.
The A31 TCON has mux controls for how TCON outputs are routed to the
HDMI and MIPI DSI blocks.
Since the A31s does not have MIPI DSI, it only has a mux for the HDMI
controller input.
This patch only adds support for the compatible strings. Actual support
for the mux controls should be added with HDMI and MIPI DSI support.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 49c440e87c upstream.
The A31's display pipeline has 2 frontends, 2 backends, and 2 TCONs. It
also has new display enhancement blocks, such as the DRC (Dynamic Range
Controller), the DEU (Display Enhancement Unit), and the CMU (Color
Management Unit). It supports HDMI, MIPI DSI, and 2 LCD/LVDS channels.
The A31s display pipeline is almost the same, just without MIPI DSI.
Only the TCON seems to be different, due to the missing mux for MIPI
DSI.
Add compatible strings for both of them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e575cbc93 upstream.
The type of AVIC interrupt controller found on i.MX31 is one-cell,
namely 31 for CCM DVFS and 53 for CCM, however for clock control
module its interrupts are specified as 3-cells, fix it.
Fixes: ef0e4a606f ("ARM: mx31: Replace clk_register_clkdev with clock DT lookup")
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8ca5bd158 upstream.
The BUCK regulators 3, 4, and 5 also have a 10mV step mode,
adjust the tables and logic to reflect the data-sheet for
these regulators.
fixes: d2a2e729a6 ("regulator: tps65086: Add regulator driver for the TPS65086 PMIC")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RGMII requires special RX and/or TX delays depending on the actual
hardware circuit/wiring. These delays can be added by the MAC, the PHY
or the designer of the circuit (the latter means that no delay has to
be added by PHY or MAC).
There are 4 RGMII phy-modes used describe where a delay should be
applied:
- rgmii: the RX and TX delays are either added by the MAC (where the
exact delay is typically configurable, and can be turned off when no
extra delay is needed) or not needed at all (because the hardware
wiring adds the delay already). The PHY should neither add the RX nor
TX delay in this case.
- rgmii-rxid: configures the PHY to enable the RX delay. The MAC should
not add the RX delay in this case.
- rgmii-txid: configures the PHY to enable the TX delay. The MAC should
not add the TX delay in this case.
- rgmii-id: combines rgmii-rxid and rgmii-txid and thus configures the
PHY to enable the RX and TX delays. The MAC should neither add the RX
nor TX delay in this case.
Document these cases in the ethernet.txt documentation to make it clear
when to use each mode.
If applied incorrectly one might end up with MAC and PHY both enabling
for example the TX delay, which breaks ethernet TX traffic on 1000Mbit/s
links.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes for omaps for v4.9-rc cycle. Except for the omap3 fix for the SoC
features printed, all these are quite trivial and tiny. The omap5 jack
detection and gpadc patches are not strictly fixes, but I wanted to get
binding document typo fixed before it pops up on other boards. The
gpadc one liner was in the same series and I applied and pushed it out
already before noticing it could have waited. The list of changes is:
- Fix omap3 SoC features printed
- Make sure OMAP_INTERCONNECT is selected for am43xx only configurations
- Add missing memory node for torpedo
- Initialize uart4_mask properly to avoid writing garbage to PRM registers
- Fix NULL pointer dereference for omap4 volt_data
- Add alias for omap5 gpadc needed by iio drivers
- Enable omap5 jack headset jack detection and fix it's binding typo
- Add missing memory node for logicpd-som-lv
- Fix wrong SMPS6 voltage for VDD-DDR3 for omap5
* tag 'omap-for-v4.9/fixes-for-rc-cycle' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap5: board-common: fix wrong SMPS6 (VDD-DDR3) voltage
ARM: omap3: Add missing memory node in SOM-LV
ASoC: omap-abe-twl6040: fix typo in bindings documentation
dts: omap5: board-common: enable twl6040 headset jack detection
dts: omap5: board-common: add phandle to reference Palmas gpadc
ARM: OMAP2+: avoid NULL pointer dereference
ARM: OMAP2+: PRM: initialize en_uart4_mask and grpsel_uart4_mask
ARM: dts: omap3: Fix memory node in Torpedo board
ARM: AM43XX: Select OMAP_INTERCONNECT in Kconfig
ARM: OMAP3: Fix formatting of features printed
Signed-off-by: Olof Johansson <olof@lixom.net>
The Aspeed SoCs have two BT interfaces : one is IPMI compliant and the
other is H8S/2168 compliant.
The current ipmi/bt-bmc driver implements the IPMI version and we
should reflect its nature in the compatible node name using
'aspeed,ast2400-ibt-bmc' instead of 'aspeed,ast2400-bt-bmc'. The
latter should be used for a H8S interface driver if it is implemented
one day.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull PCI fixes from Bjorn Helgaas:
- Update MAINTAINERS for Intel VMD driver filename
- Update Rockchip rk3399 host bridge driver DTS and resets
- Fix ROM shadow problem that made some video device initialization
fail
* tag 'pci-v4.9-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: VMD: Update filename to reflect move
arm64: dts: rockchip: add three new resets for rk3399 PCIe controller
PCI: rockchip: Add three new resets as required properties
PCI: Don't attempt to claim shadow copies of ROM
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Fix mmc card initialization for hosts not supporting HW busy
detection
- Fix mmc_test for sending commands during non-blocking write
MMC host:
- mxs: Avoid using an uninitialized
- sdhci: Restore enhanced strobe setting during runtime resume
- sdhci: Fix a couple of reset related issues
- dw_mmc: Fix a reset controller issue"
* tag 'mmc-v4.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: mxs: Initialize the spinlock prior to using it
mmc: mmc: Use 500ms as the default generic CMD6 timeout
mmc: mmc_test: Fix "Commands during non-blocking write" tests
mmc: sdhci: Fix missing enhanced strobe setting during runtime resume
mmc: sdhci: Reset cmd and data circuits after tuning failure
mmc: sdhci: Fix unexpected data interrupt handling
mmc: sdhci: Fix CMD line reset interfering with ongoing data transfer
mmc: dw_mmc: add the "reset" as name of reset controller
Documentation: synopsys-dw-mshc: add binding for reset-names
Pull pin control fixes from Linus Walleij:
"All is about drivers, no core business going on.
- Fix a host of runtime problems with the Intel Cherryview driver:
suspend/resume needs to be marshalled properly, and strange effects
from BIOS interaction during suspend/resume need to be dealt with.
- A single bit was being set wrong in the Aspeed driver.
- Fix an iProc probe ordering fallout resulting from v4.9
refactorings for bus population.
- Do not specify a default trigger in the ST Micro cascaded GPIO IRQ
controller: the kernel will moan.
- Make IRQs optional altogether on the STM32 driver, it turns out not
all systems have them or want them.
- Fix a re-probe bug in the i.MX driver, it will eventually crash if
probed repeatedly, not good"
* tag 'pinctrl-v4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl-aspeed-g5: Never set SCU90[6]
pinctrl: cherryview: Prevent possible interrupt storm on resume
pinctrl: cherryview: Serialize register access in suspend/resume
pinctrl: imx: reset group index on probe
pinctrl: stm32: move gpio irqs binding to optional
pinctrl: stm32: remove dependency with interrupt controller
pinctrl: st: don't specify default interrupt trigger
pinctrl: iproc: Fix iProc and NSP GPIO support
pm_rst, aclk_rst, pclk_rst was controlled by ROM code so the software
wasn't needed to control it again in theory. But it didn't work properly,
so we do need to do it again and add enough delay between the assert of
pm_rst and the deassert of pm_rst. The Soc intergrated with this
controller, rk3399, is still under MP test internally, so the backward
compatibility won't be a big deal.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Add reset-names property for binding dw-mmc controller.
It might be used together with "reset" property.
- Note: It must be "reset" as name.
Fixes: d6786fefe8 ("mmc: dw_mmc: add reset support to dwmmc host controller")
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
stm32 pinctrl driver could be probed even if no interrupt controller
is defined to manage gpio irqs. Entries related to gpio irq management
are moved to optional.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull networking fixes from David Miller:
"Lots of fixes, mostly drivers as is usually the case.
1) Don't treat zero DMA address as invalid in vmxnet3, from Alexey
Khoroshilov.
2) Fix element timeouts in netfilter's nft_dynset, from Anders K.
Pedersen.
3) Don't put aead_req crypto struct on the stack in mac80211, from
Ard Biesheuvel.
4) Several uninitialized variable warning fixes from Arnd Bergmann.
5) Fix memory leak in cxgb4, from Colin Ian King.
6) Fix bpf handling of VLAN header push/pop, from Daniel Borkmann.
7) Several VRF semantic fixes from David Ahern.
8) Set skb->protocol properly in ip6_tnl_xmit(), from Eli Cooper.
9) Socket needs to be locked in udp_disconnect(), from Eric Dumazet.
10) Div-by-zero on 32-bit fix in mlx4 driver, from Eugenia Emantayev.
11) Fix stale link state during failover in NCSCI driver, from Gavin
Shan.
12) Fix netdev lower adjacency list traversal, from Ido Schimmel.
13) Propvide proper handle when emitting notifications of filter
deletes, from Jamal Hadi Salim.
14) Memory leaks and big-endian issues in rtl8xxxu, from Jes Sorensen.
15) Fix DESYNC_FACTOR handling in ipv6, from Jiri Bohac.
16) Several routing offload fixes in mlxsw driver, from Jiri Pirko.
17) Fix broadcast sync problem in TIPC, from Jon Paul Maloy.
18) Validate chunk len before using it in SCTP, from Marcelo Ricardo
Leitner.
19) Revert a netns locking change that causes regressions, from Paul
Moore.
20) Add recursion limit to GRO handling, from Sabrina Dubroca.
21) GFP_KERNEL in irq context fix in ibmvnic, from Thomas Falcon.
22) Avoid accessing stale vxlan/geneve socket in data path, from
Pravin Shelar"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (189 commits)
geneve: avoid using stale geneve socket.
vxlan: avoid using stale vxlan socket.
qede: Fix out-of-bound fastpath memory access
net: phy: dp83848: add dp83822 PHY support
enic: fix rq disable
tipc: fix broadcast link synchronization problem
ibmvnic: Fix missing brackets in init_sub_crq_irqs
ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context
Revert "ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context"
arch/powerpc: Update parameters for csum_tcpudp_magic & csum_tcpudp_nofold
net/mlx4_en: Save slave ethtool stats command
net/mlx4_en: Fix potential deadlock in port statistics flow
net/mlx4: Fix firmware command timeout during interrupt test
net/mlx4_core: Do not access comm channel if it has not yet been initialized
net/mlx4_en: Fix panic during reboot
net/mlx4_en: Process all completions in RX rings after port goes up
net/mlx4_en: Resolve dividing by zero in 32-bit system
net/mlx4_core: Change the default value of enable_qos
net/mlx4_core: Avoid setting ports to auto when only one port type is supported
net/mlx4_core: Fix the resource-type enum in res tracker to conform to FW spec
...
The MAC is capable of RGMII mode and that is probably a more typical
connection type than GMII today (eg it is used by Marvell Reference
designs for several SOCs). Let DT users specify the standard
phy-connection-type = "rgmii-id";
On a phy node.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull ARM SoC fixes from Olof Johansson:
"We haven't seen a whole lot of fixes for the first two weeks since the
merge window, but here is the batch that we have at the moment.
Nothing sticks out as particularly bad or scary, it's mostly a handful
of smaller fixes to several platforms. The Uniphier reset controller
changes could probably have been delayed to 4.10, but they're not
scary and just plumbing up driver changes that went in during the
merge window.
We're also adding another maintainer to Marvell Berlin platforms, to
help out when Sebastian is too busy. Yay teamwork!"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: imx: mach-imx6q: Fix the PHY ID mask for AR8031
ARM: dts: vf610: fix IRQ flag of global timer
ARM: imx: gpc: Fix the imx_gpc_genpd_init() error path
ARM: imx: gpc: Initialize all power domains
arm64: dts: Updated NAND DT properties for NS2 SVK
arm64: dts: uniphier: change MIO node to SD control node
ARM: dts: uniphier: change MIO node to SD control node
reset: uniphier: rename MIO reset to SD reset for Pro5, PXs2, LD20 SoCs
arm64: uniphier: select ARCH_HAS_RESET_CONTROLLER
ARM: uniphier: select ARCH_HAS_RESET_CONTROLLER
arm64: dts: Add timer erratum property for LS2080A and LS1043A
arm64: dts: rockchip: remove the abuse of keep-power-in-suspend
ARM: multi_v7_defconfig: Enable Intel e1000e driver
MAINTAINERS: add myself as Marvell berlin SoC maintainer
bus: qcom-ebi2: depend on ARCH_QCOM or COMPILE_TEST
ARM: dts: fix the SD card on the Snowball
arm64: dts: rockchip: remove always-on and boot-on from vcc_sd
arm64: dts: marvell: fix clocksource for CP110 master SPI0
ARM: mvebu: Select corediv clk for all mvebu v7 SoC
Pull tty/serial driver fixes from Greg KH:
"Here are a number of small tty and serial driver fixes for reported
issues for 4.9-rc3. Nothing major, but they do resolve a bunch of
problems with the tty core changes that are in 4.9-rc1, and finally
the atmel serial driver is back working properly.
All have been in linux-next with no reported issues"
* tag 'tty-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial_core: fix NULL struct tty pointer access in uart_write_wakeup
tty: serial_core: Fix serial console crash on port shutdown
tty/serial: at91: fix hardware handshake on Atmel platforms
vt: clear selection before resizing
sc16is7xx: always write state when configuring GPIO as an output
sh-sci: document R8A7743/5 support
tty: serial: 8250: 8250_core: NXP SC16C2552 workaround
tty: limit terminal size to 4M chars
tty: serial: fsl_lpuart: Fix Tx DMA edge case
serial: 8250_lpss: enable MSI for sure
serial: core: fix console problems on uart_close
serial: 8250_uniphier: fix clearing divisor latch access bit
serial: 8250_uniphier: fix more unterminated string
serial: pch_uart: add terminate entry for dmi_system_id tables
devicetree: bindings: uart: Add new compatible string for ZynqMP
serial: xuartps: Add new compatible string for ZynqMP
serial: SERIAL_STM32 should depend on HAS_DMA
serial: stm32: Fix comparisons with undefined register
tty: vt, fix bogus division in csi_J
Pull USB fixes from Greg KH:
"Here are a number of small USB driver fixes for 4.9-rc3.
There is the usual number of gadget and xhci patches in here to
resolved reported issues, as well as some usb-serial driver fixes and
new device ids.
All have been in linux-next with no reported issues"
* tag 'usb-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (26 commits)
usb: chipidea: host: fix NULL ptr dereference during shutdown
usb: renesas_usbhs: add wait after initialization for R-Car Gen3
usb: increase ohci watchdog delay to 275 msec
usb: musb: Call pm_runtime from musb_gadget_queue
usb: musb: Fix hardirq-safe hardirq-unsafe lock order error
usb: ehci-platform: increase EHCI_MAX_RSTS to 4
usb: ohci-at91: Set RemoteWakeupConnected bit explicitly.
USB: serial: fix potential NULL-dereference at probe
xhci: use default USB_RESUME_TIMEOUT when resuming ports.
xhci: workaround for hosts missing CAS bit
xhci: add restart quirk for Intel Wildcatpoint PCH
USB: serial: cp210x: fix tiocmget error handling
wusb: fix error return code in wusb_prf()
Revert "Documentation: devicetree: dwc2: Deprecate g-tx-fifo-size"
Revert "usb: dwc2: gadget: fix TX FIFO size and address initialization"
Revert "usb: dwc2: gadget: change variable name to more meaningful"
USB: serial: ftdi_sio: add support for Infineon TriBoard TC2X7
wusb: Stop using the stack for sg crypto scratch space
usb: dwc3: Fix size used in dma_free_coherent()
usb: gadget: f_fs: stop sleeping in ffs_func_eps_disable
...
Pull clk fixes from Stephen Boyd:
"This is the first batch of clk driver fixes for this release.
We have a handful of fixes for the uniphier clk driver that was
introduced recently, as well as Kconfig option hiding, module
autoloading markings, and a few fixes for clk_hw based registration
patches that went in this merge window"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: at91: Fix a return value in case of error
clk: uniphier: rename MIO clock to SD clock for Pro5, PXs2, LD20 SoCs
clk: uniphier: fix memory overrun bug
clk: hi6220: use CLK_OF_DECLARE_DRIVER for sysctrl and mediactrl clock init
clk: mvebu: armada-37xx-periph: Fix the clock gate flag
clk: bcm2835: Clamp the PLL's requested rate to the hardware limits.
clk: max77686: fix number of clocks setup for clk_hw based registration
clk: mvebu: armada-37xx-periph: Fix the clock provider registration
clk: core: add __init decoration for CLK_OF_DECLARE_DRIVER function
clk: mediatek: Add hardware dependency
clk: samsung: clk-exynos-audss: Fix module autoload
clk: uniphier: fix type of variable passed to regmap_read()
clk: uniphier: add system clock support for sLD3 SoC
Pull IPMI updates from Corey Minyard:
"A small bug fix and a new driver for acting as an IPMI device.
I was on vacation during the merge window (a long vacation) but this
is a bug fix that should go in and a new driver that shouldn't hurt
anything.
This has been in linux-next for a month or so"
* tag 'for-linus-4.9-2' of git://git.code.sf.net/p/openipmi/linux-ipmi:
ipmi: fix crash on reading version from proc after unregisted bmc
ipmi/bt-bmc: remove redundant return value check of platform_get_resource()
ipmi/bt-bmc: add a dependency on ARCH_ASPEED
ipmi: Fix ioremap error handling in bt-bmc
ipmi: add an Aspeed BT IPMI BMC driver
Pull timer updates from Thomas Gleixner:
"This updates contains:
- A revert which addresses a boot failure on ARM Sun5i platforms
- A new clocksource driver, which has been delayed beyond rc1 due to
an interrupt driver issue which was unearthed by this driver. The
debugging of that issue and the discussion about the proper
solution made this driver miss the merge window. There is no point
in delaying it for a full cycle as it completes the basic mainline
support for the new JCore platform and does not create any risk
outside of that platform"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "clocksource/drivers/timer_sun5i: Replace code by clocksource_mmio_init"
clocksource: Add J-Core timer/clocksource driver
of: Add J-Core timer bindings
I made a mistake as for naming for this block. The MIO block is not
implemented for these 3 SoCs in the first place. The current naming
will be a trouble if an SoC with both MIO and SD-ctrl blocks appear
in the future.
This driver has just been merged in the previous merge window.
Rename it before the release.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
I made a mistake as for naming for this block. The MIO block is not
implemented for these 3 SoCs in the first place. The current naming
will be a trouble if an SoC with both MIO and SD-ctrl blocks appear
in the future.
This driver has just been merged in the previous merge window.
Rename it before the release.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The SPI1 function was associated with the wrong pins: The functions that
those pins provide is either an SPI debug or passthrough function
coupled to SPI1. Make the SPI1 mux function configure the relevant pins
and associate new SPI1DEBUG and SPI1PASSTHRU functions with the pins
that were already defined.
The notation used in the datasheet's multi-function pin table for the SoC is
often creative: in this case the SYS* signals are enabled by a single bit,
which is nothing unusual on its own, but in this case the bit was also
participating in a multi-bit bitfield and therefore represented multiple
functions. This fact was overlooked in the original patch.
Fixes: 56e57cb6c0 (pinctrl: Add pinctrl-aspeed-g5 driver)
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This binding was deprecated due to commit aa381a7259 ("usb: dwc2:
gadget: fix TX FIFO size and address initialization"). However that
commit is now reverted, so also revert this commit.
The binding is valid and shouldn't be deprecated.
This reverts commit 65e1ff7f4b ("Documentation: devicetree: dwc2:
Deprecate g-tx-fifo-size").
Signed-off-by: John Youn <johnyoun@synopsys.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Pull MIPS updates from Ralf Baechle:
"This is the main MIPS pull request for 4.9:
MIPS core arch code:
- traps: 64bit kernels should read CP0_EBase 64bit
- traps: Convert ebase to KSEG0
- c-r4k: Drop bc_wback_inv() from icache flush
- c-r4k: Split user/kernel flush_icache_range()
- cacheflush: Use __flush_icache_user_range()
- uprobes: Flush icache via kernel address
- KVM: Use __local_flush_icache_user_range()
- c-r4k: Fix flush_icache_range() for EVA
- Fix -mabi=64 build of vdso.lds
- VDSO: Drop duplicated -I*/-E* aflags
- tracing: move insn_has_delay_slot to a shared header
- tracing: disable uprobe/kprobe on compact branch instructions
- ptrace: Fix regs_return_value for kernel context
- Squash lines for simple wrapper functions
- Move identification of VP(E) into proc.c from smp-mt.c
- Add definitions of SYNC barrierstype values
- traps: Ensure full EBase is written
- tlb-r4k: If there are wired entries, don't use TLBINVF
- Sanitise coherentio semantics
- dma-default: Don't check hw_coherentio if device is non-coherent
- Support per-device DMA coherence
- Adjust MIPS64 CAC_BASE to reflect Config.K0
- Support generating Flattened Image Trees (.itb)
- generic: Introduce generic DT-based board support
- generic: Convert SEAD-3 to a generic board
- Enable hardened usercopy
- Don't specify STACKPROTECTOR in defconfigs
Octeon:
- Delete dead code and files across the platform.
- Change to use all memory into use by default.
- Rename upper case variables in setup code to lowercase.
- Delete legacy hack for broken bootloaders.
- Leave maintaining the link state to the actual ethernet/PHY drivers.
- Add DTS for D-Link DSR-500N.
- Fix PCI interrupt routing on D-Link DSR-500N.
Pistachio:
- Remove ANDROID_TIMED_OUTPUT from defconfig
TX39xx:
- Move GPIO setup from .mem_setup() to .arch_init()
- Convert to Common Clock Framework
TX49xx:
- Move GPIO setup from .mem_setup() to .arch_init()
- Convert to Common Clock Framework
txx9wdt:
- Add missing clock (un)prepare calls for CCF
BMIPS:
- Add PW, GPIO SDHCI and NAND device node names
- Support APPENDED_DTB
- Add missing bcm97435svmb to DT_NONE
- Rename bcm96358nb4ser to bcm6358-neufbox4-sercom
- Add DT examples for BCM63268, BCM3368 and BCM6362
- Add support for BCM3368 and BCM6362
PCI
- Reduce stack frame usage
- Use struct list_head lists
- Support for CONFIG_PCI_DOMAINS_GENERIC
- Make pcibios_set_cache_line_size an initcall
- Inline pcibios_assign_all_busses
- Split pci.c into pci.c & pci-legacy.c
- Introduce CONFIG_PCI_DRIVERS_LEGACY
- Support generic drivers
CPC
- Convert bare 'unsigned' to 'unsigned int'
- Avoid lock when MIPS CM >= 3 is present
GIC:
- Delete unused file smp-gic.c
mt7620:
- Delete unnecessary assignment for the field "owner" from PCI
BCM63xx:
- Let clk_disable() return immediately if clk is NULL
pm-cps:
- Change FSB workaround to CPU blacklist
- Update comments on barrier instructions
- Use MIPS standard lightweight ordering barrier
- Use MIPS standard completion barrier
- Remove selection of sync types
- Add MIPSr6 CPU support
- Support CM3 changes to Coherence Enable Register
SMP:
- Wrap call to mips_cpc_lock_other in mips_cm_lock_other
- Introduce mechanism for freeing and allocating IPIs
cpuidle:
- cpuidle-cps: Enable use with MIPSr6 CPUs.
SEAD3:
- Rewrite to use DT and generic kernel feature.
USB:
- host: ehci-sead3: Remove SEAD-3 EHCI code
FBDEV:
- cobalt_lcdfb: Drop SEAD3 support
dt-bindings:
- Document a binding for simple ASCII LCDs
auxdisplay:
- img-ascii-lcd: driver for simple ASCII LCD displays
irqchip i8259:
- i8259: Add domain before mapping parent irq
- i8259: Allow platforms to override poll function
- i8259: Remove unused i8259A_irq_pending
Malta:
- Rewrite to use DT
of/platform:
- Probe "isa" busses by default
CM:
- Print CM error reports upon bus errors
Module:
- Migrate exception table users off module.h and onto extable.h
- Make various drivers explicitly non-modular:
- Audit and remove any unnecessary uses of module.h
mailmap:
- Canonicalize to Qais' current email address.
Documentation:
- MIPS supports HAVE_REGS_AND_STACK_ACCESS_API
Loongson1C:
- Add CPU support for Loongson1C
- Add board support
- Add defconfig
- Add RTC support for Loongson1C board
All this except one Documentation fix has sat in linux-next and has
survived Imagination's automated build test system"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (127 commits)
Documentation: MIPS supports HAVE_REGS_AND_STACK_ACCESS_API
MIPS: ptrace: Fix regs_return_value for kernel context
MIPS: VDSO: Drop duplicated -I*/-E* aflags
MIPS: Fix -mabi=64 build of vdso.lds
MIPS: Enable hardened usercopy
MIPS: generic: Convert SEAD-3 to a generic board
MIPS: generic: Introduce generic DT-based board support
MIPS: Support generating Flattened Image Trees (.itb)
MIPS: Adjust MIPS64 CAC_BASE to reflect Config.K0
MIPS: Print CM error reports upon bus errors
MIPS: Support per-device DMA coherence
MIPS: dma-default: Don't check hw_coherentio if device is non-coherent
MIPS: Sanitise coherentio semantics
MIPS: PCI: Support generic drivers
MIPS: PCI: Introduce CONFIG_PCI_DRIVERS_LEGACY
MIPS: PCI: Split pci.c into pci.c & pci-legacy.c
MIPS: PCI: Inline pcibios_assign_all_busses
MIPS: PCI: Make pcibios_set_cache_line_size an initcall
MIPS: PCI: Support for CONFIG_PCI_DOMAINS_GENERIC
MIPS: PCI: Use struct list_head lists
...
Pull more rdma updates from Doug Ledford:
"This merge window was the first where Huawei had to try and coordinate
their patches between their net driver and their new roce driver
(similar to mlx4 and mlx5).
They didn't do horribly, but there were some issues (and we knew that
because they simply didn't know what to do in the beginning). As a
result, I had a set of patches that depended on some patches that
normally would have come to you via Dave's tree. Those patches have
been on netdev@ for a while, so I got Dave to give me his approval to
send them to you. As such, the other 29 patches I had behind them are
also now ready to go.
This catches the hns and hns-roce drivers up to current, and for
future patches we are working with them to get them up to speed on how
to do joint driver development so that they don't have these sorts of
cross tree dependency issues again. BTW, Dave gave me permission to
add his Acked-by: to the patches against the net tree, but I've had
this branch through 0day (but not linux-next since it was off by
itself) and I didn't want to rebase the series just to add Dave's ack
for the 8 patches in the net area.
Updates to the hns drivers:
- Small patch set for hns net driver that the roce patches depend on
- Various fixes to the hns-roce driver
- Add connection manager support to the hns-roce driver"
* tag 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (36 commits)
IB/hns: Fix for removal of redundant code
IB/hns: Delete the redundant lines in hns_roce_v1_m_qp()
IB/hns: Fix the bug when platform_get_resource() exec fail
IB/hns: Update the rq head when modify qp state
IB/hns: Cq has not been freed
IB/hns: Validate mtu when modified qp
IB/hns: Some items of qpc need to take user param
IB/hns: The Ack timeout need a lower limit value
IB/hns: Return bad wr while post send failed
IB/hns: Fix bug of memory leakage for registering user mr
IB/hns: Modify the init of iboe lock
IB/hns: Optimize code of aeq and ceq interrupt handle and fix the bug of qpn
IB/hns: Delete the sqp_start from the structure hns_roce_caps
IB/hns: Fix bug of clear hem
IB/hns: Remove unused parameter named qp_type
IB/hns: Simplify function of pd alloc and qp alloc
IB/hns: Fix bug of using uninit refcount and free
IB/hns: Remove parameters of resize cq
IB/hns: Remove unused parameters in some functions
IB/hns: Add node_guid definition to the bindings document
...
Pull some more input subsystem updates from Dmitry Torokhov:
"An update to the ALPS driver to support the V8 protocol with
touchstick, a change for i8042 to skip selftest on many Asus laptops
which helps to keep their touchpads working after resume, and a couple
other driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - skip selftest on ASUS laptops
Input: melfas_mip4 - add ic_name sysfs attribute
Input: melfas_mip4 - add maintainer information
Input: melfas_mip4 - add devicetree binding documentations
Input: elantech - add Fujitsu Lifebook E556 to force crc_enabled
Input: synaptics-rmi4 - fix error handling in I2C transport driver
Input: synaptics-rmi4 - fix error handling in SPI transport driver
Input: ALPS - add V8 protocol documentation
Input: ALPS - set DualPoint flag for 74 03 28 devices
Input: ALPS - allow touchsticks to report pressure
Input: ALPS - handle 0-pressure 1F events
Input: ALPS - add touchstick support for SS5 hardware
Input: elantech - force needed quirks on Fujitsu H760
Input: elantech - fix Lenovo version typo
