When driver was developed, FCC regulation didn't enable channel 144
and there was no demand for channel 144 at that time. Although HW
actually supports channel 144, driver didn't announce channel 144.
Therefore, channel 144 (20 MHz), channel 142 (40 MHz) and channel
138 (80 MHz) couldn't be used.
Today, channel 144 has been enabled by regulations and
is gradually being supported. With test requirements,
we declare hw supports channel 144.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201204013823.3729-1-pkshih@realtek.com
Also strip out other duplicates from driver specific headers.
Ensure 'main.h' is explicitly included in 'pci.h' since the latter
uses some defines from the former. It avoids issues like:
from drivers/net/wireless/realtek/rtw88/rtw8822be.c:5:
drivers/net/wireless/realtek/rtw88/pci.h:209:28: error: ‘RTK_MAX_TX_QUEUE_NUM’ undeclared here (not in a function); did you mean ‘RTK_MAX_RX_DESC_NUM’?
209 | DECLARE_BITMAP(tx_queued, RTK_MAX_TX_QUEUE_NUM);
| ^~~~~~~~~~~~~~~~~~~~
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/realtek/rtw88/pci.c:1488:5: warning: no previous prototype for ‘rtw_pci_probe’ [-Wmissing-prototypes]
1488 | int rtw_pci_probe(struct pci_dev *pdev,
| ^~~~~~~~~~~~~
drivers/net/wireless/realtek/rtw88/pci.c:1568:6: warning: no previous prototype for ‘rtw_pci_remove’ [-Wmissing-prototypes]
1568 | void rtw_pci_remove(struct pci_dev *pdev)
| ^~~~~~~~~~~~~~
drivers/net/wireless/realtek/rtw88/pci.c:1590:6: warning: no previous prototype for ‘rtw_pci_shutdown’ [-Wmissing-prototypes]
1590 | void rtw_pci_shutdown(struct pci_dev *pdev)
| ^~~~~~~~~~~~~~~~
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126133152.3211309-18-lee.jones@linaro.org
Incase of hardware encryption, WMI_PEER_AUTH flag will be set by firmware
during install key. Since install key wont be done for software encryption
mode, firmware will not set this flag. Due to this, seeing traffic failure
in software encryption. Hence, avoid resetting peer auth flag if hardware
encryption disabled.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01421-QCAHKSWPL_SILICONZ-1
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1606369414-25211-1-git-send-email-seevalam@codeaurora.org
cppcheck possible warnings: (new ones prefixed by >>, may not real problems)
drivers/net/wireless/ath/ath10k/sdio.c:2234:2:
warning: Non-boolean value returned from function returning bool [returnNonBoolInBooleanFunction]
return param & HI_OPTION_SDIO_CRASH_DUMP_ENHANCEMENT_FW;
Reported-by: kernel test robot <rong.a.chen@intel.com>
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00049
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1606103240-9868-1-git-send-email-wgong@codeaurora.org
In preparation to enable -Wimplicit-fallthrough for Clang, fix a
warning by replacing a /* fall through */ comment with the new
pseudo-keyword macro fallthrough; instead of letting the code fall
through to the next case.
Notice that Clang doesn't recognize /* fall through */ comments as
implicit fall-through markings.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The mcs value of HT mode reported by mt7915_mcu_get_rx_rate()
has already been converted to the expected format.
Tested-by: Yiwei Chung <yiwei.chung@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Kalle Valo says:
====================
wireless-drivers-next patches for v5.11
First set of patches for v5.11. rtw88 getting improvements to work
better with Bluetooth and other driver also getting some new features.
mhi-ath11k-immutable branch was pulled from mhi tree to avoid
conflicts with mhi tree.
Major changes:
rtw88
* major bluetooth co-existance improvements
wilc1000
* Wi-Fi Multimedia (WMM) support
ath11k
* Fast Initial Link Setup (FILS) discovery and unsolicited broadcast
probe response support
* qcom,ath11k-calibration-variant Device Tree setting
* cold boot calibration support
* new DFS region: JP
wnc36xx
* enable connection monitoring and keepalive in firmware
ath10k
* firmware IRAM recovery feature
mhi
* merge mhi-ath11k-immutable branch to make MHI API change go smoothly
* tag 'wireless-drivers-next-2020-12-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (180 commits)
wl1251: remove trailing semicolon in macro definition
airo: remove trailing semicolon in macro definition
wilc1000: added queue support for WMM
wilc1000: call complete() for failure in wilc_wlan_txq_add_cfg_pkt()
wilc1000: free resource in wilc_wlan_txq_add_mgmt_pkt() for failure path
wilc1000: free resource in wilc_wlan_txq_add_net_pkt() for failure path
wilc1000: added 'ndo_set_mac_address' callback support
brcmfmac: expose firmware config files through modinfo
wlcore: Switch to using the new API kobj_to_dev()
rtw88: coex: add feature to enhance HID coexistence performance
rtw88: coex: upgrade coexistence A2DP mechanism
rtw88: coex: add action for coexistence in hardware initial
rtw88: coex: add function to avoid cck lock
rtw88: coex: change the coexistence mechanism for WLAN connected
rtw88: coex: change the coexistence mechanism for HID
rtw88: coex: update AFH information while in free-run mode
rtw88: coex: update the mechanism for A2DP + PAN
rtw88: coex: add debug message
rtw88: coex: run coexistence when WLAN entering/leaving LPS
Revert "rtl8xxxu: Add Buffalo WI-U3-866D to list of supported devices"
...
====================
Link: https://lore.kernel.org/r/20201203185732.9CFA5C433ED@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Instead of stopping and waking only a single queue, handle all phy tx queues
mapped ot the same hardware queue.
Also allow the driver to block tx queues
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7915 automatically detects dbdc feature so drop debugfs knob.
Move if_comb, mt7915_rates, if_limits structs and mt7915_regd_notifier(),
mt7915_init_wiphy() routines at the begging of init.c in order to make
mt7915_register_ext_phy routine static
Co-developed-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to properly support mt7915 dbdc
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to introduce dbdc support to mt7915 devices
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to properly support mt7915 dbdc
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to move properly support mt7915 dbdc
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move hw data queues in mt76_phy from mt76_dev since mt7915 supports per
phy hw queues in dbdc mode
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mcu queue to a dedicated array q_mcu in mt76_dev structure.
This is a preliminary patch to move data queues in mt76_phy and properly
support dbdc
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to move data queues in mt76_phy and properly
support dbdc
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76_init_mcu_queue utility routine in order to allocate
dedicate q_mcu pointers for mcu hw queues. This is a preliminary patch
to move data queues in mt76_phy and add dbdc support to mt7915 driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rely on mt76_queue instead of qid in tx_queue_skb signature.
This is a preliminary patch to move data queues in mt76_phy and add
dbdc support to mt7915 driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to move data queues in mt76_phy and properly
support dbdc
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to move data queues in mt76_phy and properly
support dbdc for mt7915
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to move data queues in mt76_phy and properly
support dbdc for mt7915
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to move hw data queues in mt76_phy for
mt7915 dbdc support
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_init_tx_queue in mac80211.c since it is shared by all
drivers.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to make the code more readable, rely on mt7915_eeprom_field
definitions for eeprom parsing
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since wtbl workqueue is used only for rate handling, refactor code to
make it more clear
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When looking for a MAC address slot, start by using main BSSID slots 1-3,
afterwards use 16 repeater mode BSSID slots, then start using the slots
usually used for AP mode.
This search order should prevent unnecessary conflicts with AP mode interfaces
on the same PHY.
Note that two PHYs share global 32 omac slots with each other.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7915_mcu_bss_sync_tlv() is no longer used, so remove it.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The omac_idx variable is u64 so we should use the 64-bit BIT_ULL().
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Make mt7915_eeprom_read routine static since it is used only in eeprom.c
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Support to set tx frequency offset in testmode, which is usally used in
the pre-calibration stage.
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Support tx_power setting in testmode. Note that the tx power value of
antenna 1-3 equal to antenna 0.
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Support testmode rx and display rx statistic by parsing RXV packet
type, which is currently only enabled in testmode.
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
