Add unicast MAC address filtering support using install flow
message. Total of 8 MCAM entries are allocated for adding
unicast mac filtering rules. If the MCAM allocation fails,
the unicast filtering support will not be advertised.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds support for adding and deleting ethtool ntuple
filters. The filters for ether, ipv4, ipv6, tcp, udp and sctp
are supported. The mask is also supported. The supported actions
are drop and direct to a queue. Additionally we support FLOW_EXT
field vlan_tci and FLOW_MAC_EXT.
The NIX PF will allocate total 32 MCAM entries for the use of
ethtool ntuple filters. The Administrative Function(AF) will
install/delete the MCAM rules when NIX PF sends mailbox message
to install/delete the ntuple filters.
Ethtool ntuple filters support is restricted to PFs as of now
and PF can install ntuple filters to direct the traffic to its
VFs. Hence added a separate callback for VFs to get/set RSS
configuration.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Added new mailbox messages to install and delete MCAM rules.
These mailbox messages will be used for adding/deleting ethtool
n-tuple filters by NIX PF. The installed MCAM rules are stored
in a list that will be traversed later to delete the MCAM entries
when the interface is brought down or when PCIe FLR is received.
The delete mailbox supports deleting a single MCAM entry or range
of entries or all the MCAM entries owned by the pcifunc. Each MCAM
entry can be associated with a HW match stat entry if the mailbox
requester wants to check the hit count for debugging.
Modified adding default unicast DMAC match rule using install
flow API. The default unicast DMAC match entry installed by
Administrative Function is saved and can be changed later by the
mailbox user to fit additional fields, or the default MCAM entry
rule action can be used for other flow rules installed later.
Modified rvu_mbox_handler_nix_lf_free mailbox to add a flag to
disable or delete the MCAM entries. The MCAM entries are disabled
when the interface is brought down and deleted in FLR handler.
The disabled MCAM entries will be re-enabled when the interface
is brought up again.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Key Extraction(KEX) profile decides how the packet metadata such as
layer information and selected packet data bytes at each layer are
placed in MCAM search key. This patch reads the configured KEX profile
parameters to find out the bit position and bit mask for each field.
The information is used when programming the MCAM match data by SW
to match a packet flow and take appropriate action on the flow. This
patch also verifies the mandatory fields such as channel and DMAC
are not overwritten by the KEX configuration of other fields.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds support to verify the channel number sent by
mailbox requester before writing MCAM entry for Ingress packets.
Similarly for Egress packets, verifying the PF_FUNC sent by the
mailbox user.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current default Key Extraction(KEX) profile can only use RX
packet fields while generating the MCAM search key. The profile
can't be used for matching TX packet fields. This patch modifies
the default KEX profile to add support for extracting TX packet
fields into MCAM search key. Enabled Tx KPU packet parsing by
configuring TX PKIND in tx_parse_cfg.
Modified the KEX profile to extract 2 bytes of VLAN TCI from an
offset of 2 bytes from LB_PTR. The LB_PTR points to the byte offset
where the VLAN header starts. The NPC KPU parser profile has been
modified to point LB_PTR to the starting byte offset of VLAN header
which points to the tpid field.
Signed-off-by: Stanislaw Kardach <skardach@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The DLCI driver (dlci.c) implements the Frame Relay protocol. However,
we already have another newer and better implementation of Frame Relay
provided by the HDLC_FR driver (hdlc_fr.c).
The DLCI driver's implementation of Frame Relay is used by only one
hardware driver in the kernel - the SDLA driver (sdla.c).
The SDLA driver provides Frame Relay support for the Sangoma S50x devices.
However, the vendor provides their own driver (along with their own
multi-WAN-protocol implementations including Frame Relay), called WANPIPE.
I believe most users of the hardware would use the vendor-provided WANPIPE
driver instead.
(The WANPIPE driver was even once in the kernel, but was deleted in
commit 8db60bcf30 ("[WAN]: Remove broken and unmaintained Sangoma
drivers.") because the vendor no longer updated the in-kernel WANPIPE
driver.)
Cc: Mike McLagan <mike.mclagan@linux.org>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Link: https://lore.kernel.org/r/20201114150921.685594-1-xie.he.0141@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the new batched xsk interfaces for the Tx path in the i40e driver
to improve performance. On my machine, this yields a throughput
increase of 4% for the l2fwd sample app in xdpsock. If we instead just
look at the Tx part, this patch set increases throughput with above
20% for Tx.
Note that I had to explicitly loop unroll the inner loop to get to
this performance level, by using a pragma. It is honored by both clang
and gcc and should be ignored by versions that do not support
it. Using the -funroll-loops compiler command line switch on the
source file resulted in a loop unrolling on a higher level that
lead to a performance decrease instead of an increase.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/1605525167-14450-6-git-send-email-magnus.karlsson@gmail.com
Due to a hardware issue, an access to MDIO registers
that is concurrent with other ENETC register accesses
may lead to the MDIO access being dropped or corrupted.
The workaround introduces locking for all register accesses
to the ENETC register space. To reduce performance impact,
a readers-writers locking scheme has been implemented.
The writer in this case is the MDIO access code (irrelevant
whether that MDIO access is a register read or write), and
the reader is any access code to non-MDIO ENETC registers.
Also, the datapath functions acquire the read lock fewer times
and use _hot accessors. All the rest of the code uses the _wa
accessors which lock every register access.
The commit introducing MDIO support is -
commit ebfcb23d62 ("enetc: Add ENETC PF level external MDIO support")
but due to subsequent refactoring this patch is applicable on
top of a later commit.
Fixes: 6517798dd3 ("enetc: Make MDIO accessors more generic and export to include/linux/fsl")
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20201112182608.26177-1-claudiu.manoil@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: aedd133d17 ("net/mlx5e: Support CT offload for tc nic flows")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Avoid calling mlx5_esw_modify_vport_rate() if qos is not enabled and
avoid unnecessary syndrome messages from firmware.
Fixes: fcb64c0f56 ("net/mlx5: E-Switch, add ingress rate support")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently when QoS is enabled for VF and any min_rate is configured,
the driver sets bw_share value to at least 1 and doesn’t allow to set
it to 0 to make minimal rate unlimited. It means there is always a
minimal rate configured for every VF, even if user tries to remove it.
In order to make QoS disable possible, check whether all vports have
configured min_rate = 0. If this is true, set their bw_share to 0 to
disable min_rate limitations.
Fixes: c9497c9890 ("net/mlx5: Add support for setting VF min rate")
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently, if user disables VFs with some min and max rates configured,
they are cleared. But QoS data is not cleared and restored upon next VF
enable placing limits on minimal rate for given VF, when user expects
none.
To match cleared vport->info struct with QoS-related min and max rates
upon VF disable, clear vport->qos struct too.
Fixes: 556b9d16d3 ("net/mlx5: Clear VF's configuration on disabling SRIOV")
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Bond events handler uses bond_slave_get_rtnl to check if net device
is bond slave. bond_slave_get_rtnl return the rcu rx_handler pointer
from the netdev which exists for bond slaves but also exists for
devices that are attached to linux bridge so using it as indication
for bond slave is wrong.
Fix by using netif_is_lag_port instead.
Fixes: 7e51891a23 ("net/mlx5e: Use netdev events to set/del egress acl forward-to-vport rule")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Both TC and IPsec crypto offload use metadata_regB to store
private information. Since TC does not use bit 31 of regB, IPsec
will use bit 31 as the IPsec packet marker. The IPsec's regB usage
is changed to:
Bit31: IPsec marker
Bit30-24: IPsec syndrome
Bit23-0: IPsec obj id
Fixes: b2ac7541e3 ("net/mlx5e: IPsec: Add Connect-X IPsec Rx data path offload")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The IP's checksum partial still requires L4 csum flag on Ethernet WQE.
Make the IPsec WAs only for the IP's non checksum partial case
(for example icmd packet)
Fixes: 5be019040c ("net/mlx5e: IPsec: Add Connect-X IPsec Tx data path offload")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Alaa Hleihel <alaa@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
On resync, the driver calls inet_lookup_established
(__inet6_lookup_established) that increases sk_refcnt of the socket. To
decrease it, the driver set skb->destructor to sock_edemux. However, it
didn't work well, because the TCP stack also sets this destructor for
early demux, and the refcount gets decreased only once, while increased
two times (in mlx5e and in the TCP stack). It leads to a socket leak, a
TLS context leak, which in the end leads to calling tls_dev_del twice:
on socket close and on driver unload, which in turn leads to a crash.
This commit fixes the refcount leak by calling sock_gen_put right away
after using the socket, thus fixing all the subsequent issues.
Fixes: 0419d8c9d8 ("net/mlx5e: kTLS, Add kTLS RX resync support")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Besides GL(Gap Limiting), QL(Quantity Limiting) can be modified
dynamically when DIM is supported. So rename gl_adapt_enable as
adapt_enable in struct hns3_enet_coalesce.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For device whose version is above V3(include V3), the GL
configuration can set as 1us unit, so adds support for
configuring this field.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For maintainability and compatibility, add support for querying
the maximum value of GL.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
QL(quantity limiting) means that hardware supports the interrupt
coalesce based on the frame quantity. QL can be configured when
int_ql_max in device's specification is non-zero, so add support
to configure it. Also, rename two coalesce init function to fit
their purpose.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Andre Edich <andre.edich@microchip.com>
Cc: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Andre Edich <andre.edich@microchip.com>
Cc: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Marek Vasut <marex@denx.de>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Marek Vasut <marex@denx.de>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Maxim Kochetkov <fido_max@inbox.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Maxim Kochetkov <fido_max@inbox.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Nisar Sayed <Nisar.Sayed@microchip.com>
Cc: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Nisar Sayed <Nisar.Sayed@microchip.com>
Cc: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When removing the driver we would hit BUG_ON(!list_empty(&dev->ptype_specific))
in net/core/dev.c due to still having the NC-SI packet handler
registered.
# echo 1e660000.ethernet > /sys/bus/platform/drivers/ftgmac100/unbind
------------[ cut here ]------------
kernel BUG at net/core/dev.c:10254!
Internal error: Oops - BUG: 0 [#1] SMP ARM
CPU: 0 PID: 115 Comm: sh Not tainted 5.10.0-rc3-next-20201111-00007-g02e0365710c4 #46
Hardware name: Generic DT based system
PC is at netdev_run_todo+0x314/0x394
LR is at cpumask_next+0x20/0x24
pc : [<806f5830>] lr : [<80863cb0>] psr: 80000153
sp : 855bbd58 ip : 00000001 fp : 855bbdac
r10: 80c03d00 r9 : 80c06228 r8 : 81158c54
r7 : 00000000 r6 : 80c05dec r5 : 80c05d18 r4 : 813b9280
r3 : 813b9054 r2 : 8122c470 r1 : 00000002 r0 : 00000002
Flags: Nzcv IRQs on FIQs off Mode SVC_32 ISA ARM Segment none
Control: 00c5387d Table: 85514008 DAC: 00000051
Process sh (pid: 115, stack limit = 0x7cb5703d)
...
Backtrace:
[<806f551c>] (netdev_run_todo) from [<80707eec>] (rtnl_unlock+0x18/0x1c)
r10:00000051 r9:854ed710 r8:81158c54 r7:80c76bb0 r6:81158c10 r5:8115b410
r4:813b9000
[<80707ed4>] (rtnl_unlock) from [<806f5db8>] (unregister_netdev+0x2c/0x30)
[<806f5d8c>] (unregister_netdev) from [<805a8180>] (ftgmac100_remove+0x20/0xa8)
r5:8115b410 r4:813b9000
[<805a8160>] (ftgmac100_remove) from [<805355e4>] (platform_drv_remove+0x34/0x4c)
Fixes: bd466c3fb5 ("net/faraday: Support NCSI mode")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20201117024448.1170761-1-joel@jms.id.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The code in this driver which parses the devicetree to determine
the phy/fixed link setup, can be replaced by a single library
function: of_phy_get_and_connect().
Behaviour is identical, except that the library function will
complain when 'phy-connection-type' is omitted, instead of
blindly using PHY_INTERFACE_MODE_NA, which would result in an
invalid phy configuration.
The library function no longer brings out the exact phy_mode,
but the driver doesn't need this, because phy_interface_is_rgmii()
queries the phydev directly. Remove 'phy_mode' from the private
adapter struct.
While we're here, log info about the attached phy on connect,
this is useful because the phy type and connection method is now
fully configurable via the devicetree.
Tested on a lan7430 chip with built-in phy. Verified that adding
fixed-link/phy-connection-type in the devicetree results in a
fixed-link setup. Used ethtool to verify that the devicetree
settings are used.
Tested-by: Sven Van Asbroeck <thesven73@gmail.com> # lan7430
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201116170155.26967-1-TheSven73@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently we print the driver name twice in phy_attached_print():
- phy_dev_info() prints it as part of the device info
- and we print it as part of the info string
This is a little bit ugly, it makes the info harder to read,
especially if the driver name is a little bit longer.
Therefore omit the driver name (if set) in the info string.
Example from r8169 that uses phylib:
old: Generic FE-GE Realtek PHY r8169-300:00: attached PHY driver \
[Generic FE-GE Realtek PHY] (mii_bus:phy_addr=r8169-300:00, irq=IGNORE)
new: Generic FE-GE Realtek PHY r8169-300:00: attached PHY driver \
(mii_bus:phy_addr=r8169-300:00, irq=IGNORE)
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/8ab72586-f079-41d8-84ee-9f6a5bd97b2a@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
VFs do not have access permissions to issue NVM_GET_DEV_INFO
firmware command.
Fixes: 4933f6753b ("bnxt_en: Add bnxt_hwrm_nvm_get_dev_info() to query NVM info.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
