The ADIN1300/ADIN1200 support cable diagnostics using TDR.
The cable fault detection is automatically run on all four pairs looking at
all combinations of pair faults by first putting the PHY in standby (clear
the LINK_EN bit, PHY_CTRL_3 register, Address 0x0017) and then enabling the
diagnostic clock (set the DIAG_CLK_EN bit, PHY_CTRL_1 register, Address
0x0012).
Cable diagnostics can then be run (set the CDIAG_RUN bit in the
CDIAG_RUN register, Address 0xBA1B). The results are reported for each pair
in the cable diagnostics results registers, CDIAG_DTLD_RSLTS_0,
CDIAG_DTLD_RSLTS_1, CDIAG_DTLD_RSLTS_2, and CDIAG_DTLD_RSLTS_3, Address
0xBA1D to Address 0xBA20).
The distance to the first fault for each pair is reported in the cable
fault distance registers, CDIAG_FLT_DIST_0, CDIAG_FLT_DIST_1,
CDIAG_FLT_DIST_2, and CDIAG_FLT_DIST_3, Address 0xBA21 to Address 0xBA24).
This change implements support for this using phylib's cable-test support.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201103074436.93790-2-alexandru.ardelean@analog.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the PHY powers up, the diagnostics clock isn't enabled (bit 2 in
register PHY_CTRL_1 (0x0012)).
Also, the PHY is not in standby mode, so bit 13 in PHY_CTRL_3 (0x0017) is
always set at power up.
The standby mode and the diagnostics clock are both meant to be for the
cable diagnostics feature of the PHY (in phylib this would be equivalent to
the cable-test support), and for the frame-generator feature of the PHY.
In standby mode, the PHY doesn't negotiate links or manage links.
To use the cable diagnostics/test (or frame-generator), the PHY must be
first set in standby mode, so that the link operation doesn't interfere.
Then, the diagnostics clock must be enabled.
For the cable-test feature, when the operation finishes, the PHY goes into
PHY_UP state, and the config_aneg hook is called.
For the ADIN PHY, we need to make sure that during autonegotiation
configuration/setup the PHY is removed from standby mode and the
diagnostics clock is disabled, so that normal operation is resumed.
This change does that by moving the set of the ADIN1300_LINKING_EN bit (2)
in the config_aneg (to disable standby mode).
Previously, this was set in the downshift setup, because the downshift
retry value and the ADIN1300_LINKING_EN are in the same register.
And the ADIN1300_DIAG_CLK_EN bit (13) is cleared, to disable the
diagnostics clock.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201103074436.93790-1-alexandru.ardelean@analog.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We enable a channel doorbell engine only for IPA v3.5.1, and that is
now handled directly by gsi_channel_program().
When initially setting up a channel, we want that doorbell engine
enabled, and we can request that independent of the IPA version.
Doing that makes the "legacy" argument to gsi_channel_setup_one()
unnecessary. And with that gone we can get rid of the "legacy"
argument to gsi_channel_setup(), and gsi_setup() as well.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the IPA version in gsi_channel_program() to determine whether
we should enable the GSI doorbell engine when requested. This way,
callers only say whether or not it should be enabled if needed,
regardless of hardware version.
Rename the "legacy" argument to gsi_channel_reset(), and have
it indicate whether the doorbell engine should be enabled when
reprogramming following the reset.
Change all callers of gsi_channel_reset() to indicate whether to
enable the doorbell engine after reset, independent of hardware
version.
Rework a little logic in ipa_endpoint_reset() to get rid of the
"legacy" variable previously passed to gsi_channel_reset().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A quirk of IPA v3.5.1 requires a channel reset on an RX channel to
be performed twice. Use the IPA version in gsi_channel_reset()
rather than the passed-in legacy flag to determine that.
This is actually a bug fix, because this double reset is supposed
to occur independent of whether we're enabling the doorbell engine.
Now they will be independent.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A quirk of IPA v4.2 requires the AP to allocate the GSI channels
that are owned by the modem.
Rather than pass a flag argument to gsi_channel_init(), use the
IPA version directly in that function to determine whether modem
channels need to be allocated.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Record the IPA version passed to gsi_init() in the GSI structure.
This allows that value to be used directly where needed, rather than
passing and storing certain flag arguments through the code.
In particular, for all but one supported version of IPA, the command
channel is programmed to only use an "escape buffer". By storing
the IPA version, we can do a simple version check in one location,
and avoid storing a flag field in every channel (and passing a flag
along while initializing channels to set that field properly).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Although GSI is integral to IPA, it is a separate hardware component
and the IPA code supporting it has been structured to avoid explicit
dependence on IPA details. An example of this is that gsi_init() is
passed a number of Boolean flags to indicate special behaviors,
whose values are dependent on the IPA hardware version. Looking
ahead, newer hardware versions would require even more such special
behaviors.
For any given version of IPA hardware (like 3.5.1 or 4.2), the GSI
hardware version is fixed (in this case, 1.3 and 2.2, respectively).
So the IPA version *implies* the GSI version, and the IPA version
can be used as effectively the equivalent of the GSI hardware version.
Rather than proliferating new special behavior flags, just provide
the IPA version to the GSI layer when it is initialized. The GSI
code can then use that directly to determine whether special
behaviors are required. The IPA version enumerated type is already
isolated to its own header file, so the exposure of this IPA detail
is very limited.
For now, just change gsi_init() to pass the version rather than the
Boolean flags, and set the flag values internal to that function.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Marc Kleine-Budde says:
====================
pull-request: can 2020-11-03
The first two patches are by Oleksij Rempel and they add a generic
can-controller Device Tree yaml binding and convert the text based binding
of the flexcan driver to a yaml based binding.
Zhang Changzhong's patch fixes a remove_proc_entry warning in the AF_CAN
core.
A patch by me fixes a kfree_skb() call from IRQ context in the rx-offload
helper.
Vincent Mailhol contributes a patch to prevent a call to kfree_skb() in
hard IRQ context in can_get_echo_skb().
Oliver Hartkopp's patch fixes the length calculation for RTR CAN frames
in the __can_get_echo_skb() helper.
Oleksij Rempel's patch fixes a use-after-free that shows up with j1939 in
can_create_echo_skb().
Yegor Yefremov contributes 4 patches to enhance the j1939 documentation.
Zhang Changzhong's patch fixes a hanging task problem in j1939_sk_bind()
if the netdev is down.
Then there are three patches for the newly added CAN_ISOTP protocol. Geert
Uytterhoeven enhances the kconfig help text. Oliver Hartkopp's patch adds
missing RX timeout handling in listen-only mode and Colin Ian King's patch
decreases the generated object code by 926 bytes.
Zhang Changzhong contributes a patch for the ti_hecc driver that fixes the
error path in the probe function.
Navid Emamdoost's patch for the xilinx_can driver fixes the error handling
in case of failing pm_runtime_get_sync().
There are two patches for the peak_usb driver. Dan Carpenter adds range
checking in decode operations and Stephane Grosjean's patch fixes
a timestamp wrapping problem.
Stephane Grosjean's patch for th peak_canfd driver fixes echo management if
loopback is on.
The next three patches all target the mcp251xfd driver. The first one is
by me and it increased the severity of CRC read error messages. The kernel
test robot removes an unneeded semicolon and Tom Rix removes unneeded
break in several switch-cases.
The last 4 patches are by Joakim Zhang and target the flexcan driver,
the first three fix ECC related device specific quirks for the LS1021A,
LX2160A and the VF610 SoC. The last patch disable wakeup completely upon
driver remove.
* tag 'linux-can-fixes-for-5.10-20201103' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can: (27 commits)
can: flexcan: flexcan_remove(): disable wakeup completely
can: flexcan: add ECC initialization for VF610
can: flexcan: add ECC initialization for LX2160A
can: flexcan: remove FLEXCAN_QUIRK_DISABLE_MECR quirk for LS1021A
can: mcp251xfd: remove unneeded break
can: mcp251xfd: mcp251xfd_regmap_nocrc_read(): fix semicolon.cocci warnings
can: mcp251xfd: mcp251xfd_regmap_crc_read(): increase severity of CRC read error messages
can: peak_canfd: pucan_handle_can_rx(): fix echo management when loopback is on
can: peak_usb: peak_usb_get_ts_time(): fix timestamp wrapping
can: peak_usb: add range checking in decode operations
can: xilinx_can: handle failure cases of pm_runtime_get_sync
can: ti_hecc: ti_hecc_probe(): add missed clk_disable_unprepare() in error path
can: isotp: padlen(): make const array static, makes object smaller
can: isotp: isotp_rcv_cf(): enable RX timeout handling in listen-only mode
can: isotp: Explain PDU in CAN_ISOTP help text
can: j1939: j1939_sk_bind(): return failure if netdev is down
can: j1939: use backquotes for code samples
can: j1939: swap addr and pgn in the send example
can: j1939: fix syntax and spelling
can: j1939: rename jacd tool
...
====================
Link: https://lore.kernel.org/r/<20201103220636.972106-1-mkl@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With IPA v3.5.1, if IPA aggregation is active at the time an
underlying GSI channel reset is performed, some special handling
is required.
There is logic in ipa_endpoint_reset() that arranges for that
special handling, but it's done for all hardware versions, not
just IPA v3.5.1.
Fix the logic to properly restrict the special behavior.
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20201102173435.5987-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Realtek single-port 2.5Gbps Ethernet PHYs are list as below:
RTL8226-CG: the 1st generation 2.5Gbps single port PHY
RTL8226B-CG/RTL8221B-CG: the 2nd generation 2.5Gbps single port PHY
RTL8221B-VB-CG: the 3rd generation 2.5Gbps single port PHY
RTL8221B-VM-CG: the 2.5Gbps single port PHY with MACsec feature
This patch adds the minimal drivers to manage these transceivers.
Signed-off-by: Willy Liu <willy.liu@realtek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/1604281927-9874-1-git-send-email-willy.liu@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver uses in_irq() + in_serving_softirq() magic to decide if NAPI
scheduling is required or packet processing.
The usage of in_*() in drivers is phased out and Linus clearly requested
that code which changes behaviour depending on context should either be
separated or the context be conveyed in an argument passed by the caller,
which usually knows the context.
Use the `sched_napi' argument passed by the callback. It is set true if
called from the interrupt handler and NAPI should be scheduled.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Aymen Sghaier <aymen.sghaier@nxp.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Tested-by: Camelia Groza <camelia.groza@nxp.com>
dpaa_eth_napi_schedule() and caam_qi_napi_schedule() schedule NAPI if
invoked from:
- Hard interrupt context
- Any context which is not serving soft interrupts
Any context which is not serving soft interrupts includes hard interrupts
so the in_irq() check is redundant. caam_qi_napi_schedule() has a comment
about this:
/*
* In case of threaded ISR, for RT kernels in_irq() does not return
* appropriate value, so use in_serving_softirq to distinguish between
* softirq and irq contexts.
*/
if (in_irq() || !in_serving_softirq())
This has nothing to do with RT. Even on a non RT kernel force threaded
interrupts run obviously in thread context and therefore in_irq() returns
false when invoked from the handler.
The extension of the in_irq() check with !in_serving_softirq() was there
when the drivers were added, but in the out of tree FSL BSP the original
condition was in_irq() which got extended due to failures on RT.
The usage of in_xxx() in drivers is phased out and Linus clearly requested
that code which changes behaviour depending on context should either be
separated or the context be conveyed in an argument passed by the caller,
which usually knows the context. Right he is, the above construct is
clearly showing why.
The following callchains have been analyzed to end up in
dpaa_eth_napi_schedule():
qman_p_poll_dqrr()
__poll_portal_fast()
fq->cb.dqrr()
dpaa_eth_napi_schedule()
portal_isr()
__poll_portal_fast()
fq->cb.dqrr()
dpaa_eth_napi_schedule()
Both need to schedule NAPI.
The crypto part has another code path leading up to this:
kill_fq()
empty_retired_fq()
qman_p_poll_dqrr()
__poll_portal_fast()
fq->cb.dqrr()
dpaa_eth_napi_schedule()
kill_fq() is called from task context and ends up scheduling NAPI, but
that's pointless and an unintended side effect of the !in_serving_softirq()
check.
The code path:
caam_qi_poll() -> qman_p_poll_dqrr()
is invoked from NAPI and I *assume* from crypto's NAPI device and not
from qbman's NAPI device. I *guess* it is okay to skip scheduling NAPI
(because this is what happens now) but could be changed if it is wrong
due to `budget' handling.
Add an argument to __poll_portal_fast() which is true if NAPI needs to be
scheduled. This requires propagating the value to the caller including
`qman_cb_dqrr' typedef which is used by the dpaa and the crypto driver.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Aymen Sghaier <aymen.sghaier@nxp.com>
Cc: Herbert XS <herbert@gondor.apana.org.au>
Cc: Li Yang <leoyang.li@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Tested-by: Camelia Groza <camelia.groza@nxp.com>
This is the 3rd revision of the patch fix for potential null pointer dereference
with lan743x card.
The simpliest way to reproduce: boot with bare lan743x and issue "ethtool ethN"
commant where ethN is the interface with lan743x card. Example:
$ sudo ethtool eth7
dmesg:
[ 103.510336] BUG: kernel NULL pointer dereference, address: 0000000000000340
...
[ 103.510836] RIP: 0010:phy_ethtool_get_wol+0x5/0x30 [libphy]
...
[ 103.511629] Call Trace:
[ 103.511666] lan743x_ethtool_get_wol+0x21/0x40 [lan743x]
[ 103.511724] dev_ethtool+0x1507/0x29d0
[ 103.511769] ? avc_has_extended_perms+0x17f/0x440
[ 103.511820] ? tomoyo_init_request_info+0x84/0x90
[ 103.511870] ? tomoyo_path_number_perm+0x68/0x1e0
[ 103.511919] ? tty_insert_flip_string_fixed_flag+0x82/0xe0
[ 103.511973] ? inet_ioctl+0x187/0x1d0
[ 103.512016] dev_ioctl+0xb5/0x560
[ 103.512055] sock_do_ioctl+0xa0/0x140
[ 103.512098] sock_ioctl+0x2cb/0x3c0
[ 103.512139] __x64_sys_ioctl+0x84/0xc0
[ 103.512183] do_syscall_64+0x33/0x80
[ 103.512224] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 103.512274] RIP: 0033:0x7f54a9cba427
...
Previous versions can be found at:
v1:
initial version
https://lkml.org/lkml/2020/10/28/921
v2:
do not return from lan743x_ethtool_set_wol if netdev->phydev == NULL, just skip
the call of phy_ethtool_set_wol() instead.
https://lkml.org/lkml/2020/10/31/380
v3:
in function lan743x_ethtool_set_wol:
use ternary operator instead of if-else sentence (review by Markus Elfring)
return -ENETDOWN insted of -EIO (review by Andrew Lunn)
Signed-off-by: Sergej Bauer <sbauer@blackbox.su>
Link: https://lore.kernel.org/r/20201101223556.16116-1-sbauer@blackbox.su
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation for support of XM router implementation which uses
different registers to work with trees and FIB entries, introduce
a structure to hold low-level ops and implement tree manipulation
register ops.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a couple of registers used to manipulate LPM trees on XM:
The XRALTA is used to allocate the XLT LPM trees.
The XRALST is used to set and query the structure of an XLT LPM tree.
The XRALTB register is used to bind virtual router and protocol to
an allocated LPM tree.
Since the XM registers are identical to the legacy router registers
with a fixed offset, re-use their pack functions.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Virtual netdevs should use NETIF_F_GSO_SOFTWARE to forward GSO skbs
as-is and let the final drivers deal with them when supported.
Also remove NETIF_F_GSO_UDP_L4 from bonding and team drivers as it's
now included in the "software" list.
Suggested-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/net/net_failover.c:711: warning: Function parameter or member 'standby_dev' not described in 'net_failover_create'
drivers/net/net_failover.c:711: warning: Excess function parameter 'dev' description in 'net_failover_create'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201102114512.1062724-30-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/net/macvlan.c:1350: warning: Function parameter or member 'vlan' not described in 'macvlan_changelink_sources'
drivers/net/macvlan.c:1350: warning: Function parameter or member 'mode' not described in 'macvlan_changelink_sources'
drivers/net/macvlan.c:1350: warning: Function parameter or member 'data' not described in 'macvlan_changelink_sources'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201102114512.1062724-27-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/net/usb/lan78xx.c: In function ‘lan78xx_read_raw_otp’:
drivers/net/usb/lan78xx.c:825:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_write_raw_otp’:
drivers/net/usb/lan78xx.c:879:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_deferred_multicast_write’:
drivers/net/usb/lan78xx.c:1041:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_update_flowcontrol’:
drivers/net/usb/lan78xx.c:1127:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_init_mac_address’:
drivers/net/usb/lan78xx.c:1666:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_link_status_change’:
drivers/net/usb/lan78xx.c:1841:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_irq_bus_sync_unlock’:
drivers/net/usb/lan78xx.c:1920:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan8835_fixup’:
drivers/net/usb/lan78xx.c:1994:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_set_rx_max_frame_length’:
drivers/net/usb/lan78xx.c:2192:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_change_mtu’:
drivers/net/usb/lan78xx.c:2270:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_set_mac_addr’:
drivers/net/usb/lan78xx.c:2299:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_set_features’:
drivers/net/usb/lan78xx.c:2333:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_set_suspend’:
drivers/net/usb/lan78xx.c:3807:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201102114512.1062724-25-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/net/usb/r8152.c:934: warning: Function parameter or member 'blk_hdr' not described in 'fw_mac'
drivers/net/usb/r8152.c:934: warning: Function parameter or member 'reserved' not described in 'fw_mac'
drivers/net/usb/r8152.c:947: warning: Function parameter or member 'blk_hdr' not described in 'fw_phy_patch_key'
drivers/net/usb/r8152.c:947: warning: Function parameter or member 'reserved' not described in 'fw_phy_patch_key'
drivers/net/usb/r8152.c:986: warning: Function parameter or member 'blk_hdr' not described in 'fw_phy_nc'
drivers/net/usb/r8152.c:986: warning: Function parameter or member 'mode_pre' not described in 'fw_phy_nc'
drivers/net/usb/r8152.c:986: warning: Function parameter or member 'mode_post' not described in 'fw_phy_nc'
drivers/net/usb/r8152.c:986: warning: Function parameter or member 'reserved' not described in 'fw_phy_nc'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20201102114512.1062724-23-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/net/ieee802154/ca8210.c:326: warning: Function parameter or member 'readq' not described in 'ca8210_test'
drivers/net/ieee802154/ca8210.c:375: warning: Function parameter or member 'spi_transfer_complete' not described in 'ca8210_priv'
drivers/net/ieee802154/ca8210.c:375: warning: Function parameter or member 'sync_exchange_complete' not described in 'ca8210_priv'
drivers/net/ieee802154/ca8210.c:375: warning: Function parameter or member 'promiscuous' not described in 'ca8210_priv'
drivers/net/ieee802154/ca8210.c:430: warning: Function parameter or member 'short_address' not described in 'macaddr'
drivers/net/ieee802154/ca8210.c:723: warning: Function parameter or member 'cas_ctl' not described in 'ca8210_rx_done'
drivers/net/ieee802154/ca8210.c:723: warning: Excess function parameter 'arg' description in 'ca8210_rx_done'
drivers/net/ieee802154/ca8210.c:1289: warning: Excess function parameter 'device_ref' description in 'tdme_checkpibattribute'
drivers/net/ieee802154/ca8210.c:3054: warning: Function parameter or member 'spi_device' not described in 'ca8210_remove'
drivers/net/ieee802154/ca8210.c:3054: warning: Excess function parameter 'priv' description in 'ca8210_remove'
drivers/net/ieee802154/ca8210.c:3104: warning: Function parameter or member 'spi_device' not described in 'ca8210_probe'
drivers/net/ieee802154/ca8210.c:3104: warning: Excess function parameter 'priv' description in 'ca8210_probe'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Link: https://lore.kernel.org/r/20201102114512.1062724-21-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This variable is present in many source files and has not been used
anywhere (at least internally) since it was introduced.
Fixes the following W=1 kernel build warning(s):
drivers/net/fddi/skfp/ecm.c: In function ‘ecm_fsm’:
drivers/net/fddi/skfp/ecm.c:44:19: warning: ‘ID_sccs’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201102114512.1062724-3-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When AIX_EVENT is not defined, the 'if' body will be empty, which
makes GCC complain. Place bracketing around the invocation to protect
it.
Fixes the following W=1 kernel build warning(s):
drivers/net/fddi/skfp/ecm.c: In function ‘ecm_fsm’:
drivers/net/fddi/skfp/ecm.c:153:29: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201102114512.1062724-2-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The nexthop notification chain is a per-namespace chain and not a global
one like the netdev notification chain.
Therefore, a single (global) listener cannot be registered to all these
chains simultaneously as it will result in list corruptions whenever
listeners are registered / unregistered.
Instead, register a different listener in each namespace.
Currently this is not an issue because only the VXLAN driver registers a
listener to this chain, but this is going to change with netdevsim and
mlxsw also registering their own listeners.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20201101113926.705630-1-idosch@idosch.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Change the fr_rx function to make this driver support any Ethertype
when receiving skbs on normal (non-Ethernet-emulating) PVC devices.
(This driver is already able to handle any Ethertype when sending.)
Originally in the fr_rx function, the code that parses the long (10-byte)
header only recognizes a few Ethertype values and drops frames with other
Ethertype values. This patch replaces this code to make fr_rx support
any Ethertype. This patch also creates a new function fr_snap_parse as
part of the new code.
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
1.
Change the skb->len check from "<= 4" to "< 4".
At first we only need to ensure a 4-byte header is present. We indeed
normally need the 5th byte, too, but it'd be more logical and cleaner
to check its existence when we actually need it.
2.
Add an fh->ea2 check to the initial checks in fr_rx. fh->ea2 == 1 means
the second address byte is the final address byte. We only support the
case where the address length is 2 bytes.
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When an skb is received on a normal (non-Ethernet-emulating) PVC device,
call skb_reset_mac_header before we pass it to upper layers.
This is because normal PVC devices don't have header_ops, so any header we
have would not be visible to upper layer code when sending, so the header
shouldn't be visible to upper layer code when receiving, either.
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The eth_type_trans function is called when we receive frames carrying
Ethernet frames. This function expects a non-NULL pointer as an argument,
and assigns it directly to skb->dev.
However, the code handling other types of frames first assigns the pointer
to "dev", and then at the end checks whether the value is NULL, and if it
is not NULL, assigns it to skb->dev.
The two flows are different. Mixing them in this function makes the code
messy. It's better that we convert the second flow to align with how
eth_type_trans does things.
So this patch changes the code to: first make sure the pointer is not
NULL, then assign it directly to skb->dev. "dev" is no longer needed until
the end where we use it to update stats.
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
