[ Upstream commit 935327a735 ]
Meraki MR26 is an EOL wireless access point featuring a
PoE ethernet port and two dual-band 3x3 MIMO 802.11n
radios and 1x1 dual-band WIFI dedicated to scanning.
Thank you Amir for the unit and PSU.
Hardware info:
SOC : Broadcom BCM53015A1KFEBG (dual-core Cortex-A9 CPU at 800 MHz)
RAM : SK Hynix Inc. H5TQ1G63EFR, 1 GBit DDR3 SDRAM = 128 MiB
NAND : Spansion S34ML01G100TF100, 1 GBit SLC NAND Flash = 128 MiB
ETH : 1 GBit Ethernet Port - PoE (TPS23754 PoE Interface)
WIFI0 : Broadcom BCM43431KMLG, BCM43431 802.11 abgn (3x3:3)
WIFI1 : Broadcom BCM43431KMLG, BCM43431 802.11 abgn (3x3:3)
WIFI2 : Broadcom BCM43428 "Air Marshal" 802.11 abgn (1x1:1)
BUTTON: One reset key behind a small hole next to the Ethernet Port
LEDS : One amber (fault), one white (indicator) LED, separate RGB-LED
MISC : Atmel AT24C64 8KiB EEPROM i2c
: Ti INA219 26V, 12-bit, i2c output current/voltage/power monitor
SERIAL:
WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
The Serial setting is 115200-8-N-1. The board has a populated
right angle 1x4 0.1" pinheader.
The pinout is: VCC (next to J3, has the pin 1 indicator), RX, TX, GND.
Odd stuff:
- uboot does not support lzma compression, but gzip'd uImage/DTB work.
- uboot claims to support FIT, but fails to pass the DTB to the kernel.
Appending the dtb after the kernel image works.
- RGB-controller is supported through an external userspace program.
- The ubi partition contains a "board-config" volume. It stores the
MAC Address (0x66 in binary) and Serial No. (0x7c alpha-numerical).
- SoC's temperature sensor always reports that it is on fire.
This causes the system to immediately shutdown! Looking at reported
"418 degree Celsius" suggests that this sensor is not working.
WIFI:
b43 is able to initialize all three WIFIs @ 802.11bg.
| b43-phy0: Broadcom 43431 WLAN found (core revision 29)
| bcma-pci-bridge 0000:01:00.0: bus1: Switched to core: 0x812
| b43-phy0: Found PHY: Analog 9, Type 7 (HT), Revision 1
| b43-phy0: Found Radio: Manuf 0x17F, ID 0x2059, Revision 0, Version 1
| b43-phy0 warning: 5 GHz band is unsupported on this PHY
| b43-phy1: Broadcom 43431 WLAN found (core revision 29)
| bcma-pci-bridge 0001:01:00.0: bus2: Switched to core: 0x812
| b43-phy1: Found PHY: Analog 9, Type 7 (HT), Revision 1
| b43-phy1: Found Radio: Manuf 0x17F, ID 0x2059, Revision 0, Version 1
| b43-phy1 warning: 5 GHz band is unsupported on this PHY
| b43-phy2: Broadcom 43228 WLAN found (core revision 30)
| bcma-pci-bridge 0002:01:00.0: bus3: Switched to core: 0x812
| b43-phy2: Found PHY: Analog 9, Type 4 (N), Revision 16
| b43-phy2: Found Radio: Manuf 0x17F, ID 0x2057, Revision 9, Version 1
| Broadcom 43xx driver loaded [ Features: NL ]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c6cf86e1a ]
imx6ul is not compatible to imx6sx, both have different erratas.
Fixes the dt_binding_check warning:
spi@21e0000: compatible: 'oneOf' conditional failed, one must be fixed:
['fsl,imx6ul-qspi', 'fsl,imx6sx-qspi'] is too long
Additional items are not allowed ('fsl,imx6sx-qspi' was unexpected)
'fsl,imx6ul-qspi' is not one of ['fsl,ls1043a-qspi']
'fsl,imx6ul-qspi' is not one of ['fsl,imx8mq-qspi']
'fsl,ls1021a-qspi' was expected
'fsl,imx7d-qspi' was expected
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a884d17ca ]
In yaml binding "fsl,imx6ul-lcdif" is listed as compatible to imx6sx-lcdif,
but not imx28-lcdif. Change the list accordingly. Fixes the
dt_binding_check warning:
lcdif@21c8000: compatible: 'oneOf' conditional failed, one must be fixed:
['fsl,imx6ul-lcdif', 'fsl,imx28-lcdif'] is too long
Additional items are not allowed ('fsl,imx28-lcdif' was unexpected)
'fsl,imx6ul-lcdif' is not one of ['fsl,imx23-lcdif', 'fsl,imx28-lcdif',
'fsl,imx6sx-lcdif']
'fsl,imx6sx-lcdif' was expected
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0aca931a2 ]
"fsl,imx6ul-csi" was never listed as compatible to "fsl,imx7-csi", neither
in yaml bindings, nor previous txt binding. Remove the imx7 part. Fixes
the dt schema check warning:
csi@21c4000: compatible: 'oneOf' conditional failed, one must be fixed:
['fsl,imx6ul-csi', 'fsl,imx7-csi'] is too long
Additional items are not allowed ('fsl,imx7-csi' was unexpected)
'fsl,imx8mm-csi' was expected
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d15e0c9a5 ]
According to binding, the compatible shall only contain imx6ul and imx21
compatibles. Fixes the dt_binding_check warning:
keypad@20b8000: compatible: 'oneOf' conditional failed, one must be fixed:
['fsl,imx6ul-kpp', 'fsl,imx6q-kpp', 'fsl,imx21-kpp'] is too long
Additional items are not allowed ('fsl,imx6q-kpp', 'fsl,imx21-kpp' were
unexpected)
Additional items are not allowed ('fsl,imx21-kpp' was unexpected)
'fsl,imx21-kpp' was expected
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit edb6784398 ]
operating-points is a uint32-matrix as per opp-v1.yaml. Change it
accordingly. While at it, change fsl,soc-operating-points as well,
although there is no bindings file (yet). But they should have the same
format. Fixes the dt_binding_check warning:
cpu@0: operating-points:0: [696000, 1275000, 528000, 1175000, 396000,
1025000, 198000, 950000] is too long
cpu@0: operating-points:0: Additional items are not allowed (528000,
1175000, 396000, 1025000, 198000, 950000 were unexpected)
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5655699cf5 ]
All 3 properties are required by sram.yaml. Fixes the dtbs_check
warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d0c1aadf1 ]
The USBH composed of EHCI and OHCI controllers needs the PHY clock to be
initialized first, before enabling (gating) them. The reverse is also
required when going to suspend.
So, add USBPHY clock as 1st entry in both controllers, so the USBPHY PLL
gets enabled 1st upon controller init. Upon suspend/resume, this also makes
the clock to be disabled/re-enabled in the correct order.
This fixes some IRQ storm conditions seen when going to low-power, due to
PHY PLL being disabled before all clocks are cleanly gated.
Fixes: 949a0c0dec ("ARM: dts: stm32: add USB Host (USBH) support to stm32mp157c")
Fixes: db7be2cb87 ("ARM: dts: stm32: use usbphyc ck_usbo_48m as USBH OHCI clock on stm32mp151")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db7be2cb87 ]
Referring to the note under USBH reset and clocks chapter of RM0436,
"In order to access USBH_OHCI registers it is necessary to activate the USB
clocks by enabling the PLL controlled by USBPHYC" (ck_usbo_48m).
The point is, when USBPHYC PLL is not enabled, OHCI register access
freezes the resume from STANDBY. It is the case when dual USBH is enabled,
instead of OTG + single USBH.
When OTG is probed, as ck_usbo_48m is USBO clock parent, then USBPHYC PLL
is enabled and OHCI register access is OK.
This patch adds ck_usbo_48m (provided by USBPHYC PLL) as clock of USBH
OHCI, thus USBPHYC PLL will be enabled and OHCI register access will be OK.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 93a8ba2a61 upstream.
Contrary to what was believed at the time, the ramp delay of 150us is not
plenty for the PU LDO with the default step time of 512 pulses of the 24MHz
clock. Measurements have shown that after enabling the LDO the voltage on
VDDPU_CAP jumps to ~750mV in the first step and after that the regulator
executes the normal ramp up as defined by the step size control.
This means it takes the regulator between 360us and 370us to ramp up to
the nominal 1.15V voltage for this power domain. With the old setting of
the ramp delay the power up of the PU GPC domain would happen in the middle
of the regulator ramp with the voltage being at around 900mV. Apparently
this was enough for most units to properly power up the peripherals in the
domain and execute the reset. Some units however, fail to power up properly,
especially when the chip is at a low temperature. In that case any access
to the GPU registers would yield an incorrect result with no way to recover
from this situation.
Change the ramp delay to 380us to cover the measured ramp up time with a
bit of additional slack.
Fixes: 40130d327f ("ARM: dts: imx6qdl: Allow disabling the PU regulator, add a enable ramp delay")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 552ca27929 upstream.
Move the power domain to its actual user. This keeps the power domain
enabled even when the USB host is runtime suspended. This is necessary
to detect any downstream events, like device attach.
Fixes: 02f8eb40ef ("ARM: dts: imx7s: Add power domain for imx7d HSIC")
Suggested-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 57f718aa4b ]
The red LED on the Raspberry Pi 3 B Plus is the power LED.
So fix the GPIO line name accordingly.
Fixes: 71c0cd2283 ("ARM: dts: bcm2837: Add Raspberry Pi 3 B+")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fd26fd027 ]
The GPIOs 46 & 47 are already used for a I2C interface to a SMPS.
So fix the GPIO line names accordingly.
Fixes: a54fe8a6cf ("ARM: dts: add Raspberry Pi Compute Module 3 and IO board")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c663e5e5b ]
The GPIOs 30 to 39 are connected to the Cypress CYW43438 (Wifi/BT).
So fix the GPIO line names accordingly.
Fixes: 2c7c040c73 ("ARM: dts: bcm2835: Add Raspberry Pi Zero W")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f5c579a34 ]
Fix names of extra pingroup node and property for gpio bus recovery.
Without the change i2c2 is not functional.
Fixes: 56f0df6b6b ("ARM: dts: imx*(colibri|apalis): add missing recovery modes to i2c")
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d397a1277 ]
Commit f3e7dae323 ("ARM: dts: imx6qdl: add enet_out clk
support") added another item to the list of clocks for the fec
device. As imx6dl-eckelmann-ci4x10.dts only overwrites clocks,
but not clock-names this resulted in an inconsistency with
clocks having one item more than clock-names.
Also overwrite clock-names with the same value as in
imx6qdl.dtsi. This is a no-op today, but prevents similar
inconsistencies if the soc file will be changed in a similar way
in the future.
Signed-off-by: Thorsten Scherer <t.scherer@eckelmann.de>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: f3e7dae323 ("ARM: dts: imx6qdl: add enet_out clk support")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01a850ee61 ]
The F1C100 series of SoCs actually have their watchdog IP being
compatible with the newer Allwinner generation, not the older one.
The currently described sun4i-a10-wdt actually does not work, neither
the watchdog functionality (just never fires), nor the reset part
(reboot hangs).
Replace the compatible string with the one used by the newer generation.
Verified to work with both the watchdog and reboot functionality on a
LicheePi Nano.
Also add the missing interrupt line and clock source, to make it binding
compliant.
Fixes: 4ba16d17ef ("ARM: dts: suniv: add initial DTSI file for F1C100s")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220317162349.739636-4-andre.przywara@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 130b5e32ba ]
This fixes:
arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dtb: cru-bus@100: 'pin-controller@1c0' does not match any of the regexes: '^clock-controller@[a-f0-9]+$', '^phy@[a-f0-9]+$', '^pinctrl@[a-f0-9]+$', '^syscon@[a-f0-9]+$', '^thermal@[a-f0-9]+$'
From schema: Documentation/devicetree/bindings/mfd/brcm,cru.yaml
arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dtb: pin-controller@1c0: $nodename:0: 'pin-controller@1c0' does not match '^(pinctrl|pinmux)(@[0-9a-f]+)?$'
From schema: Documentation/devicetree/bindings/pinctrl/brcm,ns-pinmux.yaml
Ref: e7391b021e ("dt-bindings: mfd: brcm,cru: Rename pinctrl node")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31fd9b79dc ]
This describes CRU in a way matching documentation and fixes:
arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dt.yaml: cru@100: $nodename:0: 'cru@100' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
From schema: /lib/python3.6/site-packages/dtschema/schemas/simple-bus.yaml
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
