Pull tty / serial driver updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.0-rc1.
It was delayed from last week as I wanted to make sure the last commit
here got some good testing in linux-next and elsewhere as it seemed to
show up only late in testing for some reason.
Nothing major here, just lots of cleanups from Jiri and Ilpo to make
the tty core cleaner (Jiri) and the rs485 code simpler to use (Ilpo).
Also included in here is the obligatory n_gsm updates from Daniel
Starke and lots of tiny driver updates and minor fixes and tweaks for
other smaller serial drivers.
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (186 commits)
tty: serial: qcom-geni-serial: Fix %lu -> %u in print statements
tty: amiserial: Fix comment typo
tty: serial: document uart_get_console()
tty: serial: serial_core, reformat kernel-doc for functions
Documentation: serial: link uart_ops properly
Documentation: serial: move GPIO kernel-doc to the functions
Documentation: serial: dedup kernel-doc for uart functions
Documentation: serial: move uart_ops documentation to the struct
dt-bindings: serial: snps-dw-apb-uart: Document Rockchip RV1126
serial: mvebu-uart: uart2 error bits clearing
tty: serial: fsl_lpuart: correct the count of break characters
serial: stm32: make info structs static to avoid sparse warnings
serial: fsl_lpuart: zero out parity bit in CS7 mode
tty: serial: qcom-geni-serial: Fix get_clk_div_rate() which otherwise could return a sub-optimal clock rate.
serial: 8250_bcm2835aux: Add missing clk_disable_unprepare()
tty: vt: initialize unicode screen buffer
serial: remove VR41XX serial driver
serial: 8250: lpc18xx: Remove redundant sanity check for RS485 flags
serial: 8250_dwlib: remove redundant sanity check for RS485 flags
dt_bindings: rs485: Correct delay values
...
The error path when get clock frequency fails in bcm2835aux_serial
driver does not correctly disable the clock.
This flaw was found using a static analysis tool "Hulk Robot", which
reported the following warning when analyzing linux-next/master:
drivers/tty/serial/8250/8250_bcm2835aux.c:
warning: clk_disable_unprepare_missing.cocci
The cocci script checks for the existence of clk_disable_unprepare()
paired with clk_prepare_enable().
Add the missing clk_disable_unprepare() to the error path.
Fixes: fcc446c8aa ("serial: 8250_bcm2835aux: Add ACPI support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Guo Mengqi <guomengqi3@huawei.com>
Link: https://lore.kernel.org/r/20220715023312.37808-1-guomengqi3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In serial8250_em485_config() the termination GPIO is set with the uart_port
spinlock held. This is an issue if setting the GPIO line can sleep (e.g.
since the concerning GPIO expander is connected via SPI or I2C).
Fix this by setting the termination line outside of the uart_port spinlock
in the serial core and using gpiod_set_value_cansleep() which instead of
gpiod_set_value() allows it to sleep.
Beside fixing the termination GPIO line setting for the 8250 driver this
change also makes setting the termination GPIO generic for all UART
drivers.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20220710164442.2958979-4-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With PSLVERR_RESP_EN parameter set to 1, the device generates an error
response when an attempt to read an empty RBR with FIFO enabled.
This happens when LCR writes are ignored when UART is busy.
dw8250_check_lcr() in retries to update LCR, invokes dw8250_force_idle()
to clear and reset FIFO and eventually reads UART_RX causing the error.
Avoid this by not reading RBR/UART_RX when no data is available.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: VAMSHI GAJJELA <vamshigajjela@google.com>
Link: https://lore.kernel.org/r/20220713131722.2316829-1-vamshigajjela@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some Freescale 8250 implementations have the problem that a single long
break results in one irq per character frame time. The code in
fsl8250_handle_irq() that is supposed to handle that uses the BI bit in
lsr_saved_flags to detect such a situation and then skip the second
received character. However it also stores other error bits and so after
a single frame error the character received in the next irq handling is
passed to the upper layer with a frame error, too.
So after a spike on the data line (which is correctly recognized as a
frame error) the following valid character is thrown away, because the
driver reports a frame error for that one, too.
To weaken this problem restrict saving LSR to only the BI bit.
Note however that the handling is still broken:
- lsr_saved_flags is updated using orig_lsr which is the LSR content
for the first received char, but there might be more in the FIFO, so
a character is thrown away that is received later and not necessarily
the one following the break.
- The doubled break might be the 2nd and 3rd char in the FIFO, so the
workaround doesn't catch these, because serial8250_rx_chars() doesn't
handle the workaround.
- lsr_saved_flags might have set UART_LSR_BI at the entry of
fsl8250_handle_irq() which doesn't originate from
fsl8250_handle_irq()'s "up->lsr_saved_flags |= orig_lsr &
UART_LSR_BI;" but from e.g. from serial8250_tx_empty().
- For a long or a short break this isn't about two characters, but more
or only a single one.
Fixes: 9deaa53ac7 ("serial: add irq handler for Freescale 16550 errata.")
Acked-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220704085119.55900-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When console is enabled, univ8250_console_setup() calls
serial8250_console_setup() before .dev is set to uart_port. Therefore,
it will not call pm_runtime_get_sync(). Later, when the actual driver
is going to take over univ8250_console_exit() is called. As .dev is
already set, serial8250_console_exit() makes pm_runtime_put_sync() call
with usage count being zero triggering PM usage count warning
(extra debug for univ8250_console_setup(), univ8250_console_exit(), and
serial8250_register_ports()):
[ 0.068987] univ8250_console_setup ttyS0 nodev
[ 0.499670] printk: console [ttyS0] enabled
[ 0.717955] printk: console [ttyS0] printing thread started
[ 1.960163] serial8250_register_ports assigned dev for ttyS0
[ 1.976830] printk: console [ttyS0] disabled
[ 1.976888] printk: console [ttyS0] printing thread stopped
[ 1.977073] univ8250_console_exit ttyS0 usage:0
[ 1.977075] serial8250 serial8250: Runtime PM usage count underflow!
[ 1.977429] dw-apb-uart.6: ttyS0 at MMIO 0x4010006000 (irq = 33, base_baud = 115200) is a 16550A
[ 1.977812] univ8250_console_setup ttyS0 usage:2
[ 1.978167] printk: console [ttyS0] printing thread started
[ 1.978203] printk: console [ttyS0] enabled
To fix the issue, call pm_runtime_get_sync() in
serial8250_register_ports() as soon as .dev is set for an uart_port
if it has console enabled.
This problem became apparent only recently because 82586a7215 ("PM:
runtime: Avoid device usage count underflows") added the warning
printout. I confirmed this problem also occurs with v5.18 (w/o the
warning printout, obviously).
Fixes: bedb404e91 ("serial: 8250_port: Don't use power management for kernel console")
Cc: stable <stable@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/b4f428e9-491f-daf2-2232-819928dc276e@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If port->mapbase = NULL in serial8250_request_std_resource() , it need
return a error code instead of 0. If uart_set_info() fail to request new
regions by serial8250_request_std_resource() but the return value of
serial8250_request_std_resource() is 0, The system incorrectly considers
that the resource application is successful and does not attempt to
restore the old setting. A null pointer reference is triggered when the
port resource is later invoked.
Signed-off-by: Yi Yang <yiyang13@huawei.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220628083515.64138-1-yiyang13@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e8ffbb71f7 ("serial: 8250: use THRE & __stop_tx also with
DMA") changed __dma_tx_complete() to enable THRI that is cleared in
__stop_tx() once THRE is asserted as UART runs out bits to transmit. It
is possible, however, that more data arrives in between in which case
serial8250_tx_dma() resumes Tx. THRI is not supposed to be on during
DMA Tx because DMA is based on completion handler, therefore THRI must
be cleared unconditionally in serial8250_tx_dma().
When Tx is about to start, another race window exists with
serial8250_handle_irq() leading to a call into __stop_tx() while the
Tx has already been resumed:
__tx_complete():
-> spin_lock(port->lock)
-> dma->tx_running = 0
-> serial8250_set_THRI()
-> spin_unlock(port->lock)
uart_start():
serial8250_handle_irq():
-> spin_lock(port->lock)
-> serial8250_tx_dma():
-> dma->tx_running = 1
-> spin_unlock(port->lock)
-> spin_lock(port->lock)
-> __stop_tx()
Close this race by checking !dma->tx_running before calling into
__stop_tx().
Fixes: e8ffbb71f7 ("serial: 8250: use THRE & __stop_tx also with DMA")
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220615090651.15340-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use 32-bit reads in order to not lose higher bits of DW UART regs. This
change does not fix any known issue as the high bits are not used for
anything related to 8250 driver (dw8250_readl_ext and dw8250_writel_ext
used within the dwlib are already doing
readl/writel/ioread32be/iowrite32be anyway).
This change is necessary to enables 9th bit address mode. DW UART
reports address frames with BIT(8) of LSR.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624204210.11112-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Serial core handles serial_rs485 sanitization.
When em485 init fails, there are two possible paths of entry:
1) uart_rs485_config (init path) that fully clears port->rs485 on
error.
2) ioctl path with a pre-existing, valid port->rs485 unto which the
kernel falls back on error and port->rs485 should therefore be
kept untouched. The temporary rs485 struct is not returned to
userspace in case of error so its flag don't matter.
...Thus SER_RS485_ENABLED clearing on error can/should be dropped.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-37-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A few serial drivers make a call to rs485_config() themselves (all
these seem to relate to init). Convert them all to use a common helper
which makes it easy to make adjustments on tasks related to it as
serial_rs485 struct sanitization is going to be added.
In pci_fintek_setup() (in 8250_pci.c), the rs485_config() call was made
with NULL, however, it can be changed to pass uart_port's rs485 struct.
No other callers should pass NULL into rs485_config() so the NULL check
can now be eliminated.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
