commit 34333cc6c2 upstream.
Regarding segments with a limit==0xffffffff, the SDM officially states:
When the effective limit is FFFFFFFFH (4 GBytes), these accesses may
or may not cause the indicated exceptions. Behavior is
implementation-specific and may vary from one execution to another.
In practice, all CPUs that support VMX ignore limit checks for "flat
segments", i.e. an expand-up data or code segment with base=0 and
limit=0xffffffff. This is subtly different than wrapping the effective
address calculation based on the address size, as the flat segment
behavior also applies to accesses that would wrap the 4g boundary, e.g.
a 4-byte access starting at 0xffffffff will access linear addresses
0xffffffff, 0x0, 0x1 and 0x2.
Fixes: f9eb4af67c ("KVM: nVMX: VMX instructions: add checks for #GP/#SS exceptions")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8570f9e881 upstream.
The address size of an instruction affects the effective address, not
the virtual/linear address. The final address may still be truncated,
e.g. to 32-bits outside of long mode, but that happens irrespective of
the address size, e.g. a 32-bit address size can yield a 64-bit virtual
address when using FS/GS with a non-zero base.
Fixes: 064aea7747 ("KVM: nVMX: Decoding memory operands of VMX instructions")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 946c522b60 upstream.
The VMCS.EXIT_QUALIFCATION field reports the displacements of memory
operands for various instructions, including VMX instructions, as a
naturally sized unsigned value, but masks the value by the addr size,
e.g. given a ModRM encoded as -0x28(%ebp), the -0x28 displacement is
reported as 0xffffffd8 for a 32-bit address size. Despite some weird
wording regarding sign extension, the SDM explicitly states that bits
beyond the instructions address size are undefined:
In all cases, bits of this field beyond the instruction’s address
size are undefined.
Failure to sign extend the displacement results in KVM incorrectly
treating a negative displacement as a large positive displacement when
the address size of the VMX instruction is smaller than KVM's native
size, e.g. a 32-bit address size on a 64-bit KVM.
The very original decoding, added by commit 064aea7747 ("KVM: nVMX:
Decoding memory operands of VMX instructions"), sort of modeled sign
extension by truncating the final virtual/linear address for a 32-bit
address size. I.e. it messed up the effective address but made it work
by adjusting the final address.
When segmentation checks were added, the truncation logic was kept
as-is and no sign extension logic was introduced. In other words, it
kept calculating the wrong effective address while mostly generating
the correct virtual/linear address. As the effective address is what's
used in the segment limit checks, this results in KVM incorreclty
injecting #GP/#SS faults due to non-existent segment violations when
a nested VMM uses negative displacements with an address size smaller
than KVM's native address size.
Using the -0x28(%ebp) example, an EBP value of 0x1000 will result in
KVM using 0x100000fd8 as the effective address when checking for a
segment limit violation. This causes a 100% failure rate when running
a 32-bit KVM build as L1 on top of a 64-bit KVM L0.
Fixes: f9eb4af67c ("KVM: nVMX: VMX instructions: add checks for #GP/#SS exceptions")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98ae70cc47 upstream.
Commit ca83b4a7f2 ("x86/KVM/VMX: Add find_msr() helper function")
introduces the helper function find_msr(), which returns -ENOENT when
not find the msr in vmx->msr_autoload.guest/host. Correct checking contion
of no more available entry in vmx->msr_autoload.
Fixes: ca83b4a7f2 ("x86/KVM/VMX: Add find_msr() helper function")
Cc: stable@vger.kernel.org
Signed-off-by: Xiaoyao Li <xiaoyao.li@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b1971c694 upstream.
SDM says MSR_IA32_VMX_PROCBASED_CTLS2 is only available "If
(CPUID.01H:ECX.[5] && IA32_VMX_PROCBASED_CTLS[63])". It was found that
some old cpus (namely "Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz (family: 0x6,
model: 0xf, stepping: 0x6") don't have it. Add the missing check.
Reported-by: Zdenek Kaspar <zkaspar82@gmail.com>
Tested-by: Zdenek Kaspar <zkaspar82@gmail.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b284909aba upstream.
With the following commit:
73d5e2b472 ("cpu/hotplug: detect SMT disabled by BIOS")
... the hotplug code attempted to detect when SMT was disabled by BIOS,
in which case it reported SMT as permanently disabled. However, that
code broke a virt hotplug scenario, where the guest is booted with only
primary CPU threads, and a sibling is brought online later.
The problem is that there doesn't seem to be a way to reliably
distinguish between the HW "SMT disabled by BIOS" case and the virt
"sibling not yet brought online" case. So the above-mentioned commit
was a bit misguided, as it permanently disabled SMT for both cases,
preventing future virt sibling hotplugs.
Going back and reviewing the original problems which were attempted to
be solved by that commit, when SMT was disabled in BIOS:
1) /sys/devices/system/cpu/smt/control showed "on" instead of
"notsupported"; and
2) vmx_vm_init() was incorrectly showing the L1TF_MSG_SMT warning.
I'd propose that we instead consider #1 above to not actually be a
problem. Because, at least in the virt case, it's possible that SMT
wasn't disabled by BIOS and a sibling thread could be brought online
later. So it makes sense to just always default the smt control to "on"
to allow for that possibility (assuming cpuid indicates that the CPU
supports SMT).
The real problem is #2, which has a simple fix: change vmx_vm_init() to
query the actual current SMT state -- i.e., whether any siblings are
currently online -- instead of looking at the SMT "control" sysfs value.
So fix it by:
a) reverting the original "fix" and its followup fix:
73d5e2b472 ("cpu/hotplug: detect SMT disabled by BIOS")
bc2d8d262c ("cpu/hotplug: Fix SMT supported evaluation")
and
b) changing vmx_vm_init() to query the actual current SMT state --
instead of the sysfs control value -- to determine whether the L1TF
warning is needed. This also requires the 'sched_smt_present'
variable to exported, instead of 'cpu_smt_control'.
Fixes: 73d5e2b472 ("cpu/hotplug: detect SMT disabled by BIOS")
Reported-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Joe Mario <jmario@redhat.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: kvm@vger.kernel.org
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/e3a85d585da28cc333ecbc1e78ee9216e6da9396.1548794349.git.jpoimboe@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2dd5146e9 upstream.
nested_get_vmcs12_pages() processes the posted_intr address in vmcs12. It
caches the kmap()ed page object and pointer, however, it doesn't handle
errors correctly: it's possible to cache a valid pointer, then release
the page and later dereference the dangling pointer.
I was able to reproduce with the following steps:
1. Call vmlaunch with valid posted_intr_desc_addr but an invalid
MSR_EFER. This causes nested_get_vmcs12_pages() to cache the kmap()ed
pi_desc_page and pi_desc. Later the invalid EFER value fails
check_vmentry_postreqs() which fails the first vmlaunch.
2. Call vmlanuch with a valid EFER but an invalid posted_intr_desc_addr
(I set it to 2G - 0x80). The second time we call nested_get_vmcs12_pages
pi_desc_page is unmapped and released and pi_desc_page is set to NULL
(the "shouldn't happen" clause). Due to the invalid
posted_intr_desc_addr, kvm_vcpu_gpa_to_page() fails and
nested_get_vmcs12_pages() returns. It doesn't return an error value so
vmlaunch proceeds. Note that at this time we have a dangling pointer in
vmx->nested.pi_desc and POSTED_INTR_DESC_ADDR in L0's vmcs.
3. Issue an IPI in L2 guest code. This triggers a call to
vmx_complete_nested_posted_interrupt() and pi_test_and_clear_on() which
dereferences the dangling pointer.
Vulnerable code requires nested and enable_apicv variables to be set to
true. The host CPU must also support posted interrupts.
Fixes: 5e2f30b756 "KVM: nVMX: get rid of nested_get_page()"
Cc: stable@vger.kernel.org
Reviewed-by: Andy Honig <ahonig@google.com>
Signed-off-by: Cfir Cohen <cfir@google.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1e4329ee2c ]
The inline keyword which is not at the beginning of the function
declaration may trigger the following build warnings, so let's fix it:
arch/x86/kvm/vmx.c:1309:1: warning: ‘inline’ is not at beginning of declaration [-Wold-style-declaration]
arch/x86/kvm/vmx.c:5947:1: warning: ‘inline’ is not at beginning of declaration [-Wold-style-declaration]
arch/x86/kvm/vmx.c:5985:1: warning: ‘inline’ is not at beginning of declaration [-Wold-style-declaration]
arch/x86/kvm/vmx.c:6023:1: warning: ‘inline’ is not at beginning of declaration [-Wold-style-declaration]
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f48b4711dd ]
When guest transitions from/to long-mode by modifying MSR_EFER.LMA,
the list of shared MSRs to be saved/restored on guest<->host
transitions is updated (See vmx_set_efer() call to setup_msrs()).
On every entry to guest, vcpu_enter_guest() calls
vmx_prepare_switch_to_guest(). This function should also take care
of setting the shared MSRs to be saved/restored. However, the
function does nothing in case we are already running with loaded
guest state (vmx->loaded_cpu_state != NULL).
This means that even when guest modifies MSR_EFER.LMA which results
in updating the list of shared MSRs, it isn't being taken into account
by vmx_prepare_switch_to_guest() because it happens while we are
running with loaded guest state.
To fix above mentioned issue, add a flag to mark that the list of
shared MSRs has been updated and modify vmx_prepare_switch_to_guest()
to set shared MSRs when running with host state *OR* list of shared
MSRs has been updated.
Note that this issue was mistakenly introduced by commit
678e315e78 ("KVM: vmx: add dedicated utility to access guest's
kernel_gs_base") because previously vmx_set_efer() always called
vmx_load_host_state() which resulted in vmx_prepare_switch_to_guest() to
set shared MSRs.
Fixes: 678e315e78 ("KVM: vmx: add dedicated utility to access guest's kernel_gs_base")
Reported-by: Eyal Moscovici <eyal.moscovici@oracle.com>
Reviewed-by: Mihai Carabas <mihai.carabas@oracle.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 326e742533 upstream.
Since commit e79f245dde ("X86/KVM: Properly update 'tsc_offset' to
represent the running guest"), vcpu->arch.tsc_offset meaning was
changed to always reflect the tsc_offset value set on active VMCS.
Regardless if vCPU is currently running L1 or L2.
However, above mentioned commit failed to also change
kvm_vcpu_write_tsc_offset() to set vcpu->arch.tsc_offset correctly.
This is because vmx_write_tsc_offset() could set the tsc_offset value
in active VMCS to given offset parameter *plus vmcs12->tsc_offset*.
However, kvm_vcpu_write_tsc_offset() just sets vcpu->arch.tsc_offset
to given offset parameter. Without taking into account the possible
addition of vmcs12->tsc_offset. (Same is true for SVM case).
Fix this issue by changing kvm_x86_ops->write_tsc_offset() to return
actually set tsc_offset in active VMCS and modify
kvm_vcpu_write_tsc_offset() to set returned value in
vcpu->arch.tsc_offset.
In addition, rename write_tsc_offset() callback to write_l1_tsc_offset()
to make it clear that it is meant to set L1 TSC offset.
Fixes: e79f245dde ("X86/KVM: Properly update 'tsc_offset' to represent the running guest")
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Reviewed-by: Mihai Carabas <mihai.carabas@oracle.com>
Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Signed-off-by: Leonid Shatz <leonid.shatz@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cfb634fe30 ]
According to volume 3 of the SDM, bits 63:15 and 12:4 of the exit
qualification field for debug exceptions are reserved (cleared to
0). However, the SDM is incorrect about bit 16 (corresponding to
DR6.RTM). This bit should be set if a debug exception (#DB) or a
breakpoint exception (#BP) occurred inside an RTM region while
advanced debugging of RTM transactional regions was enabled. Note that
this is the opposite of DR6.RTM, which "indicates (when clear) that a
debug exception (#DB) or breakpoint exception (#BP) occurred inside an
RTM region while advanced debugging of RTM transactional regions was
enabled."
There is still an issue with stale DR6 bits potentially being
misreported for the current debug exception. DR6 should not have been
modified before vectoring the #DB exception, and the "new DR6 bits"
should be available somewhere, but it was and they aren't.
Fixes: b96fb43977 ("KVM: nVMX: fixes to nested virt interrupt injection")
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I'm observing random crashes in multi-vCPU L2 guests running on KVM on
Hyper-V. I bisected the issue to the commit 877ad952be ("KVM: vmx: Add
tlb_remote_flush callback support"). Hyper-V TLFS states:
"AddressSpace specifies an address space ID (an EPT PML4 table pointer)"
So apparently, Hyper-V doesn't expect us to pass naked EPTP, only PML4
pointer should be used. Strip off EPT configuration information before
calling into vmx_hv_remote_flush_tlb().
Fixes: 877ad952be ("KVM: vmx: Add tlb_remote_flush callback support")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit b5861e5cf2 introduced a check on
the interrupt-window and NMI-window CPU execution controls in order to
inject an external interrupt vmexit before the first guest instruction
executes. However, when APIC virtualization is enabled the host does not
need a vmexit in order to inject an interrupt at the next interrupt window;
instead, it just places the interrupt vector in RVI and the processor will
inject it as soon as possible. Therefore, on machines with APICv it is
not enough to check the CPU execution controls: the same scenario can also
happen if RVI>vPPR.
Fixes: b5861e5cf2
Reviewed-by: Nikita Leshchenko <nikita.leshchenko@oracle.com>
Cc: Sean Christopherson <sean.j.christopherson@intel.com>
Cc: Liran Alon <liran.alon@oracle.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As of commit 8d860bbeed ("kvm: vmx: Basic APIC virtualization controls
have three settings"), KVM will disable VIRTUALIZE_APIC_ACCESSES when
a nested guest writes APIC_BASE MSR and kvm-intel.flexpriority=0,
whereas previously KVM would allow a nested guest to enable
VIRTUALIZE_APIC_ACCESSES so long as it's supported in hardware. That is,
KVM now advertises VIRTUALIZE_APIC_ACCESSES to a guest but doesn't
(always) allow setting it when kvm-intel.flexpriority=0, and may even
initially allow the control and then clear it when the nested guest
writes APIC_BASE MSR, which is decidedly odd even if it doesn't cause
functional issues.
Hide the control completely when the module parameter is cleared.
reported-by: Sean Christopherson <sean.j.christopherson@intel.com>
Fixes: 8d860bbeed ("kvm: vmx: Basic APIC virtualization controls have three settings")
Cc: Jim Mattson <jmattson@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Return early from vmx_set_virtual_apic_mode() if the processor doesn't
support VIRTUALIZE_APIC_ACCESSES or VIRTUALIZE_X2APIC_MODE, both of
which reside in SECONDARY_VM_EXEC_CONTROL. This eliminates warnings
due to VMWRITEs to SECONDARY_VM_EXEC_CONTROL (VMCS field 401e) failing
on processors without secondary exec controls.
Remove the similar check for TPR shadowing as it is incorporated in the
flexpriority_enabled check and the APIC-related code in
vmx_update_msr_bitmap() is further gated by VIRTUALIZE_X2APIC_MODE.
Reported-by: Gerhard Wiesinger <redhat@wiesinger.com>
Fixes: 8d860bbeed ("kvm: vmx: Basic APIC virtualization controls have three settings")
Cc: Jim Mattson <jmattson@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
L2 IA32_BNDCFGS should be updated with vmcs12->guest_bndcfgs only
when VM_ENTRY_LOAD_BNDCFGS is specified in vmcs12->vm_entry_controls.
Otherwise, L2 IA32_BNDCFGS should be set to vmcs01->guest_bndcfgs which
is L1 IA32_BNDCFGS.
Reviewed-by: Nikita Leshchenko <nikita.leshchenko@oracle.com>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit a87036add0 ("KVM: x86: disable MPX if host did not enable
MPX XSAVE features") introduced kvm_mpx_supported() to return true
iff MPX is enabled in the host.
However, that commit seems to have missed replacing some calls to
kvm_x86_ops->mpx_supported() to kvm_mpx_supported().
Complete original commit by replacing remaining calls to
kvm_mpx_supported().
Fixes: a87036add0 ("KVM: x86: disable MPX if host did not enable
MPX XSAVE features")
Suggested-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Before this commit, KVM exposes MPX VMX controls to L1 guest only based
on if KVM and host processor supports MPX virtualization.
However, these controls should be exposed to guest only in case guest
vCPU supports MPX.
Without this change, a L1 guest running with kernel which don't have
commit 691bd4340b ("kvm: vmx: allow host to access guest
MSR_IA32_BNDCFGS") asserts in QEMU on the following:
qemu-kvm: error: failed to set MSR 0xd90 to 0x0
qemu-kvm: .../qemu-2.10.0/target/i386/kvm.c:1801 kvm_put_msrs:
Assertion 'ret == cpu->kvm_msr_buf->nmsrs failed'
This is because L1 KVM kvm_init_msr_list() will see that
vmx_mpx_supported() (As it only checks MPX VMX controls support) and
therefore KVM_GET_MSR_INDEX_LIST IOCTL will include MSR_IA32_BNDCFGS.
However, later when L1 will attempt to set this MSR via KVM_SET_MSRS
IOCTL, it will fail because !guest_cpuid_has_mpx(vcpu).
Therefore, fix the issue by exposing MPX VMX controls to L1 guest only
when vCPU supports MPX.
Fixes: 36be0b9deb ("KVM: x86: Add nested virtualization support for MPX")
Reported-by: Eyal Moscovici <eyal.moscovici@oracle.com>
Reviewed-by: Nikita Leshchenko <nikita.leshchenko@oracle.com>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM has an old optimization whereby accesses to the kernel GS base MSR
are trapped when the guest is in 32-bit and not when it is in 64-bit mode.
The idea is that swapgs is not available in 32-bit mode, thus the
guest has no reason to access the MSR unless in 64-bit mode and
32-bit applications need not pay the price of switching the kernel GS
base between the host and the guest values.
However, this optimization adds complexity to the code for little
benefit (these days most guests are going to be 64-bit anyway) and in fact
broke after commit 678e315e78 ("KVM: vmx: add dedicated utility to
access guest's kernel_gs_base", 2018-08-06); the guest kernel GS base
can be corrupted across SMIs and UEFI Secure Boot is therefore broken
(a secure boot Linux guest, for example, fails to reach the login prompt
about half the time). This patch just removes the optimization; the
kernel GS base MSR is now never trapped by KVM, similarly to the FS and
GS base MSRs.
Fixes: 678e315e78
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
According to section "Checks on VMX Controls" in Intel SDM vol 3C, the
following check needs to be enforced on vmentry of L2 guests:
If the 'enable VPID' VM-execution control is 1, the value of the
of the VPID VM-execution control field must not be 0000H.
Signed-off-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Reviewed-by: Mark Kanda <mark.kanda@oracle.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
According to section "Checks on VMX Controls" in Intel SDM vol 3C,
the following check needs to be enforced on vmentry of L2 guests:
- Bits 5:0 of the posted-interrupt descriptor address are all 0.
- The posted-interrupt descriptor address does not set any bits
beyond the processor's physical-address width.
Signed-off-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Reviewed-by: Mark Kanda <mark.kanda@oracle.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Reviewed-by: Karl Heubaum <karl.heubaum@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In case L1 do not intercept L2 HLT or enter L2 in HLT activity-state,
it is possible for a vCPU to be blocked while it is in guest-mode.
According to Intel SDM 26.6.5 Interrupt-Window Exiting and
Virtual-Interrupt Delivery: "These events wake the logical processor
if it just entered the HLT state because of a VM entry".
Therefore, if L1 enters L2 in HLT activity-state and L2 has a pending
deliverable interrupt in vmcs12->guest_intr_status.RVI, then the vCPU
should be waken from the HLT state and injected with the interrupt.
In addition, if while the vCPU is blocked (while it is in guest-mode),
it receives a nested posted-interrupt, then the vCPU should also be
waken and injected with the posted interrupt.
To handle these cases, this patch enhances kvm_vcpu_has_events() to also
check if there is a pending interrupt in L2 virtual APICv provided by
L1. That is, it evaluates if there is a pending virtual interrupt for L2
by checking RVI[7:4] > VPPR[7:4] as specified in Intel SDM 29.2.1
Evaluation of Pending Interrupts.
Note that this also handles the case of nested posted-interrupt by the
fact RVI is updated in vmx_complete_nested_posted_interrupt() which is
called from kvm_vcpu_check_block() -> kvm_arch_vcpu_runnable() ->
kvm_vcpu_running() -> vmx_check_nested_events() ->
vmx_complete_nested_posted_interrupt().
Reviewed-by: Nikita Leshenko <nikita.leshchenko@oracle.com>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
VMX cannot be enabled under SMM, check it when CR4 is set and when nested
virtualization state is restored.
This should fix some WARNs reported by syzkaller, mostly around
alloc_shadow_vmcs.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A VMX preemption timer value of '0' is guaranteed to cause a VMExit
prior to the CPU executing any instructions in the guest. Use the
preemption timer (if it's supported) to trigger immediate VMExit
in place of the current method of sending a self-IPI. This ensures
that pending VMExit injection to L1 occurs prior to executing any
instructions in the guest (regardless of nesting level).
When deferring VMExit injection, KVM generates an immediate VMExit
from the (possibly nested) guest by sending itself an IPI. Because
hardware interrupts are blocked prior to VMEnter and are unblocked
(in hardware) after VMEnter, this results in taking a VMExit(INTR)
before any guest instruction is executed. But, as this approach
relies on the IPI being received before VMEnter executes, it only
works as intended when KVM is running as L0. Because there are no
architectural guarantees regarding when IPIs are delivered, when
running nested the INTR may "arrive" long after L2 is running e.g.
L0 KVM doesn't force an immediate switch to L1 to deliver an INTR.
For the most part, this unintended delay is not an issue since the
events being injected to L1 also do not have architectural guarantees
regarding their timing. The notable exception is the VMX preemption
timer[1], which is architecturally guaranteed to cause a VMExit prior
to executing any instructions in the guest if the timer value is '0'
at VMEnter. Specifically, the delay in injecting the VMExit causes
the preemption timer KVM unit test to fail when run in a nested guest.
Note: this approach is viable even on CPUs with a broken preemption
timer, as broken in this context only means the timer counts at the
wrong rate. There are no known errata affecting timer value of '0'.
[1] I/O SMIs also have guarantees on when they arrive, but I have
no idea if/how those are emulated in KVM.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
[Use a hook for SVM instead of leaving the default in x86.c - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Provide a singular location where the VMX preemption timer bit is
set/cleared so that future usages of the preemption timer can ensure
the VMCS bit is up-to-date without having to modify unrelated code
paths. For example, the preemption timer can be used to force an
immediate VMExit. Cache the status of the timer to avoid redundant
VMREAD and VMWRITE, e.g. if the timer stays armed across multiple
VMEnters/VMExits.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A VMX preemption timer value of '0' at the time of VMEnter is
architecturally guaranteed to cause a VMExit prior to the CPU
executing any instructions in the guest. This architectural
definition is in place to ensure that a previously expired timer
is correctly recognized by the CPU as it is possible for the timer
to reach zero and not trigger a VMexit due to a higher priority
VMExit being signalled instead, e.g. a pending #DB that morphs into
a VMExit.
Whether by design or coincidence, commit f4124500c2 ("KVM: nVMX:
Fully emulate preemption timer") special cased timer values of '0'
and '1' to ensure prompt delivery of the VMExit. Unlike '0', a
timer value of '1' has no has no architectural guarantees regarding
when it is delivered.
Modify the timer emulation to trigger immediate VMExit if and only
if the timer value is '0', and document precisely why '0' is special.
Do this even if calibration of the virtual TSC failed, i.e. VMExit
will occur immediately regardless of the frequency of the timer.
Making only '0' a special case gives KVM leeway to be more aggressive
in ensuring the VMExit is injected prior to executing instructions in
the nested guest, and also eliminates any ambiguity as to why '1' is
a special case, e.g. why wasn't the threshold for a "short timeout"
set to 10, 100, 1000, etc...
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Consider the case L1 had a IRQ/NMI event until it executed
VMLAUNCH/VMRESUME which wasn't delivered because it was disallowed
(e.g. interrupts disabled). When L1 executes VMLAUNCH/VMRESUME,
L0 needs to evaluate if this pending event should cause an exit from
L2 to L1 or delivered directly to L2 (e.g. In case L1 don't intercept
EXTERNAL_INTERRUPT).
Usually this would be handled by L0 requesting a IRQ/NMI window
by setting VMCS accordingly. However, this setting was done on
VMCS01 and now VMCS02 is active instead. Thus, when L1 executes
VMLAUNCH/VMRESUME we force L0 to perform pending event evaluation by
requesting a KVM_REQ_EVENT.
Note that above scenario exists when L1 KVM is about to enter L2 but
requests an "immediate-exit". As in this case, L1 will
disable-interrupts and then send a self-IPI before entering L2.
Reviewed-by: Nikita Leshchenko <nikita.leshchenko@oracle.com>
Co-developed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Lack of the kvm_ prefix gives the impression that it's a VMX or SVM
specific function, and there's no conflict that prevents adding the
kvm_ prefix.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Re-execution after an emulation decode failure is only intended to
handle a case where two or vCPUs race to write a shadowed page, i.e.
we should never re-execute an instruction as part of MMIO emulation.
As handle_ept_misconfig() is only used for MMIO emulation, it should
pass EMULTYPE_NO_REEXECUTE when using the emulator to skip an instr
in the fast-MMIO case where VM_EXIT_INSTRUCTION_LEN is invalid.
And because the cr2 value passed to x86_emulate_instruction() is only
destined for use when retrying or reexecuting, we can simply call
emulate_instruction().
Fixes: d391f12070 ("x86/kvm/vmx: do not use vm-exit instruction length
for fast MMIO when running nested")
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Pull x86 fixes from Thomas Gleixner:
- Correct the L1TF fallout on 32bit and the off by one in the 'too much
RAM for protection' calculation.
- Add a helpful kernel message for the 'too much RAM' case
- Unbreak the VDSO in case that the compiler desides to use indirect
jumps/calls and emits retpolines which cannot be resolved because the
kernel uses its own thunks, which does not work for the VDSO. Make it
use the builtin thunks.
- Re-export start_thread() which was unexported when the 32/64bit
implementation was unified. start_thread() is required by modular
binfmt handlers.
- Trivial cleanups
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/speculation/l1tf: Suggest what to do on systems with too much RAM
x86/speculation/l1tf: Fix off-by-one error when warning that system has too much RAM
x86/kvm/vmx: Remove duplicate l1d flush definitions
x86/speculation/l1tf: Fix overflow in l1tf_pfn_limit() on 32bit
x86/process: Re-export start_thread()
x86/mce: Add notifier_block forward declaration
x86/vdso: Fix vDSO build if a retpoline is emitted
Two bug fixes:
1) missing entries in the l1d_param array; this can cause a host crash
if an access attempts to reach the missing entry. Future-proof the get
function against any overflows as well. However, the two entries
VMENTER_L1D_FLUSH_EPT_DISABLED and VMENTER_L1D_FLUSH_NOT_REQUIRED must
not be accepted by the parse function, so disable them there.
2) invalid values must be rejected even if the CPU does not have the
bug, so test for them before checking boot_cpu_has(X86_BUG_L1TF)
... and a small refactoring, since the .cmd field is redundant with
the index in the array.
Reported-by: Bandan Das <bsd@redhat.com>
Cc: stable@vger.kernel.org
Fixes: a7b9020b06
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Virtualization of Intel SGX depends on Enclave Page Cache (EPC)
management that is not yet available in the kernel, i.e. KVM support
for exposing SGX to a guest cannot be added until basic support
for SGX is upstreamed, which is a WIP[1].
Until SGX is properly supported in KVM, ensure a guest sees expected
behavior for ENCLS, i.e. all ENCLS #UD. Because SGX does not have a
true software enable bit, e.g. there is no CR4.SGXE bit, the ENCLS
instruction can be executed[1] by the guest if SGX is supported by the
system. Intercept all ENCLS leafs (via the ENCLS- exiting control and
field) and unconditionally inject #UD.
[1] https://www.spinics.net/lists/kvm/msg171333.html or
https://lkml.org/lkml/2018/7/3/879
[2] A guest can execute ENCLS in the sense that ENCLS will not take
an immediate #UD, but no ENCLS will ever succeed in a guest
without explicit support from KVM (map EPC memory into the guest),
unless KVM has a *very* egregious bug, e.g. accidentally mapped
EPC memory into the guest SPTEs. In other words this patch is
needed only to prevent the guest from seeing inconsistent behavior,
e.g. #GP (SGX not enabled in Feature Control MSR) or #PF (leaf
operand(s) does not point at EPC memory) instead of #UD on ENCLS.
Intercepting ENCLS is not required to prevent the guest from truly
utilizing SGX.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20180814163334.25724-3-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pull first set of KVM updates from Paolo Bonzini:
"PPC:
- minor code cleanups
x86:
- PCID emulation and CR3 caching for shadow page tables
- nested VMX live migration
- nested VMCS shadowing
- optimized IPI hypercall
- some optimizations
ARM will come next week"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (85 commits)
kvm: x86: Set highest physical address bits in non-present/reserved SPTEs
KVM/x86: Use CC_SET()/CC_OUT in arch/x86/kvm/vmx.c
KVM: X86: Implement PV IPIs in linux guest
KVM: X86: Add kvm hypervisor init time platform setup callback
KVM: X86: Implement "send IPI" hypercall
KVM/x86: Move X86_CR4_OSXSAVE check into kvm_valid_sregs()
KVM: x86: Skip pae_root shadow allocation if tdp enabled
KVM/MMU: Combine flushing remote tlb in mmu_set_spte()
KVM: vmx: skip VMWRITE of HOST_{FS,GS}_BASE when possible
KVM: vmx: skip VMWRITE of HOST_{FS,GS}_SEL when possible
KVM: vmx: always initialize HOST_{FS,GS}_BASE to zero during setup
KVM: vmx: move struct host_state usage to struct loaded_vmcs
KVM: vmx: compute need to reload FS/GS/LDT on demand
KVM: nVMX: remove a misleading comment regarding vmcs02 fields
KVM: vmx: rename __vmx_load_host_state() and vmx_save_host_state()
KVM: vmx: add dedicated utility to access guest's kernel_gs_base
KVM: vmx: track host_state.loaded using a loaded_vmcs pointer
KVM: vmx: refactor segmentation code in vmx_save_host_state()
kvm: nVMX: Fix fault priority for VMX operations
kvm: nVMX: Fix fault vector for VMX operation at CPL > 0
...
Merge L1 Terminal Fault fixes from Thomas Gleixner:
"L1TF, aka L1 Terminal Fault, is yet another speculative hardware
engineering trainwreck. It's a hardware vulnerability which allows
unprivileged speculative access to data which is available in the
Level 1 Data Cache when the page table entry controlling the virtual
address, which is used for the access, has the Present bit cleared or
other reserved bits set.
If an instruction accesses a virtual address for which the relevant
page table entry (PTE) has the Present bit cleared or other reserved
bits set, then speculative execution ignores the invalid PTE and loads
the referenced data if it is present in the Level 1 Data Cache, as if
the page referenced by the address bits in the PTE was still present
and accessible.
While this is a purely speculative mechanism and the instruction will
raise a page fault when it is retired eventually, the pure act of
loading the data and making it available to other speculative
instructions opens up the opportunity for side channel attacks to
unprivileged malicious code, similar to the Meltdown attack.
While Meltdown breaks the user space to kernel space protection, L1TF
allows to attack any physical memory address in the system and the
attack works across all protection domains. It allows an attack of SGX
and also works from inside virtual machines because the speculation
bypasses the extended page table (EPT) protection mechanism.
The assoicated CVEs are: CVE-2018-3615, CVE-2018-3620, CVE-2018-3646
The mitigations provided by this pull request include:
- Host side protection by inverting the upper address bits of a non
present page table entry so the entry points to uncacheable memory.
- Hypervisor protection by flushing L1 Data Cache on VMENTER.
- SMT (HyperThreading) control knobs, which allow to 'turn off' SMT
by offlining the sibling CPU threads. The knobs are available on
the kernel command line and at runtime via sysfs
- Control knobs for the hypervisor mitigation, related to L1D flush
and SMT control. The knobs are available on the kernel command line
and at runtime via sysfs
- Extensive documentation about L1TF including various degrees of
mitigations.
Thanks to all people who have contributed to this in various ways -
patches, review, testing, backporting - and the fruitful, sometimes
heated, but at the end constructive discussions.
There is work in progress to provide other forms of mitigations, which
might be less horrible performance wise for a particular kind of
workloads, but this is not yet ready for consumption due to their
complexity and limitations"
* 'l1tf-final' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (75 commits)
x86/microcode: Allow late microcode loading with SMT disabled
tools headers: Synchronise x86 cpufeatures.h for L1TF additions
x86/mm/kmmio: Make the tracer robust against L1TF
x86/mm/pat: Make set_memory_np() L1TF safe
x86/speculation/l1tf: Make pmd/pud_mknotpresent() invert
x86/speculation/l1tf: Invert all not present mappings
cpu/hotplug: Fix SMT supported evaluation
KVM: VMX: Tell the nested hypervisor to skip L1D flush on vmentry
x86/speculation: Use ARCH_CAPABILITIES to skip L1D flush on vmentry
x86/speculation: Simplify sysfs report of VMX L1TF vulnerability
Documentation/l1tf: Remove Yonah processors from not vulnerable list
x86/KVM/VMX: Don't set l1tf_flush_l1d from vmx_handle_external_intr()
x86/irq: Let interrupt handlers set kvm_cpu_l1tf_flush_l1d
x86: Don't include linux/irq.h from asm/hardirq.h
x86/KVM/VMX: Introduce per-host-cpu analogue of l1tf_flush_l1d
x86/irq: Demote irq_cpustat_t::__softirq_pending to u16
x86/KVM/VMX: Move the l1tf_flush_l1d test to vmx_l1d_flush()
x86/KVM/VMX: Replace 'vmx_l1d_flush_always' with 'vmx_l1d_flush_cond'
x86/KVM/VMX: Don't set l1tf_flush_l1d to true from vmx_l1d_flush()
cpu/hotplug: detect SMT disabled by BIOS
...
Remove open-coded uses of set instructions to use CC_SET()/CC_OUT() in
arch/x86/kvm/vmx.c.
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
[Mark error paths as unlikely while touching this. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The host's FS.base and GS.base rarely change, e.g. ~0.1% of host/guest
swaps on my system. Cache the last value written to the VMCS and skip
the VMWRITE to the associated VMCS fields when loading host state if
the value hasn't changed since the last VMWRITE.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
On a 64-bit host, FS.sel and GS.sel are all but guaranteed to be 0,
which in turn means they'll rarely change. Skip the VMWRITE for the
associated VMCS fields when loading host state if the selector hasn't
changed since the last VMWRITE.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The HOST_{FS,GS}_BASE fields are guaranteed to be written prior to
VMENTER, by way of vmx_prepare_switch_to_guest(). Initialize the
fields to zero for 64-bit kernels instead of pulling the base values
from their respective MSRs. In addition to eliminating two RDMSRs,
vmx_prepare_switch_to_guest() can safely assume the initial value of
the fields is zero in all cases.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make host_state a property of a loaded_vmcs so that it can be
used as a cache of the VMCS fields, e.g. to lazily VMWRITE the
corresponding VMCS field. Treating host_state as a cache does
not work if it's not VMCS specific as the cache would become
incoherent when switching between vmcs01 and vmcs02.
Move vmcs_host_cr3 and vmcs_host_cr4 into host_state.
Explicitly zero out host_state when allocating a new VMCS for a
loaded_vmcs. Unlike the pre-existing vmcs_host_cr{3,4} usage,
the segment information is not guaranteed to be (re)initialized
when running a new nested VMCS, e.g. HOST_FS_BASE is not written
in vmx_set_constant_host_state().
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove fs_reload_needed and gs_ldt_reload_needed from host_state
and instead compute whether we need to reload various state at
the time we actually do the reload. The state that is tracked
by the *_reload_needed variables is not any more volatile than
the trackers themselves.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
prepare_vmcs02() has an odd comment that says certain fields are
"not in vmcs02". AFAICT the intent of the comment is to document
that various VMCS fields are not handled by prepare_vmcs02(),
e.g. HOST_{FS,GS}_{BASE,SELECTOR}. While technically true, the
comment is misleading, e.g. it can lead the reader to think that
KVM never writes those fields to vmcs02.
Remove the comment altogether as the handling of FS and GS is
not specific to nested VMX, and GUEST_PML_INDEX has been written
by prepare_vmcs02() since commit "4e59516a12a6 (kvm: vmx: ensure
VMCS is current while enabling PML)"
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
