The debug text for how many clocks have been registered
uses "%d" with a size_t. Correct it to "%zd".
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
The driver is based on the HiFiBerry DAC driver. However HiFiBerry DAC+ uses
a different codec chip (PCM5122), therefore a new driver is necessary.
Add support for the HiFiBerry DAC+ Pro.
The HiFiBerry DAC+ and DAC+ Pro products both use the existing bcm sound driver with the DAC+ Pro having a special clock device driver representing the two high precision oscillators.
An addition bug fix is included for the PCM512x codec where by the physical size of the sample frame is used in the calculation of the LRCK divisor as it was found to be wrong when using 24-bit depth sample contained in a little endian 4-byte sample frame.
Limit PCM512x "Digital" gain to 0dB by default with HiFiBerry DAC+
24db_digital_gain DT param can be used to specify that PCM512x
codec "Digital" volume control should not be limited to 0dB gain,
and if specified will allow the full 24dB gain.
Add dt param to force HiFiBerry DAC+ Pro into slave mode
"dtoverlay=hifiberry-dacplus,slave"
Add 'slave' param to use HiFiBerry DAC+ Pro in slave mode,
with Pi as master for bit and frame clock.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
Fixed a bug when using 352.8kHz sample rate
Signed-off-by: Daniel Matuschek <daniel@hifiberry.com>
ASoC: pcm512x: revert downstream changes
This partially reverts commit 185ea05465
which was added by https://github.com/raspberrypi/linux/pull/1152
The downstream pcm512x changes caused a regression, it broke normal
use of the 24bit format with the codec, eg when using simple-audio-card.
The actual bug with 24bit playback is the incorrect usage
of physical_width in various drivers in the downstream tree
which causes 24bit data to be transmitted with 32 clock
cycles. So it's not the pcm512x that needs fixing, it's the
soundcard drivers.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplus: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplus: transmit S24_LE with 64 BCLK cycles
Signed-off-by: Matthias Reichl <hias@horus.com>
These divide off of PLLD_PER and are used for the ethernet and wifi
PHYs source PLLs. Neither of them is currently represented by a phy
device that would grab the clock for us.
This keeps other drivers from killing the networking PHYs when they
disable their own clocks and trigger PLLD_PER's refcount going to 0.
v2: Skip marking as critical if they aren't on at boot.
Signed-off-by: Eric Anholt <eric@anholt.net>
The VPU is responsible for managing the core clock, usually under
direction from the bcm2835-cpufreq driver but not via the clk-bcm2835
driver. Since the core frequency can change without warning, it is
safer to report the maximum clock rate to users of the core clock -
I2C, SPI and the mini UART - to err on the safe side when calculating
clock divisors.
If the DT node for the clock driver includes a reference to the
firmware node, use the firmware API to query the maximum core clock
instead of reading the divider registers.
Prior to this patch, a "100KHz" I2C bus was sometimes clocked at about
160KHz. In particular, switching to the 4.9 kernel was likely to break
SenseHAT usage on a Pi3.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The claim-clocks property can be used to prevent PLLs and dividers
from being marked as critical. It contains a vector of clock IDs,
as defined by dt-bindings/clock/bcm2835.h.
Use this mechanism to claim PLLD_DSI0, PLLD_DSI1, PLLH_AUX and
PLLH_PIX for the vc4_kms_v3d driver.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The VPU configures and relies on several PLLs and dividers. Mark all
enabled dividers and their PLLs as CRITICAL to prevent the kernel from
switching them off.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
commit bc5d922c93 upstream.
Take a parent rate of 180 MHz, and a requested rate of 4.285715 MHz.
This results in a theorical divider of 41.999993 which is then rounded
up to 42. The .round_rate function would then return (180 MHz / 42) as
the clock, rounded down, so 4.285714 MHz.
Calling clk_set_rate on 4.285714 MHz would round the rate again, and
give a theorical divider of 42,0000028, now rounded up to 43, and the
rate returned would be (180 MHz / 43) which is 4.186046 MHz, aka. not
what we requested.
Fix this by rounding up the divisions.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Maarten ter Huurne <maarten@treewalker.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 785c9f411e upstream.
Platform driver driver_override field should not be initialized from
const memory because the core later kfree() it. If driver_override is
manually set later through sysfs, kfree() of old value leads to:
$ echo "new_value" > /sys/bus/platform/drivers/.../driver_override
kernel BUG at ../mm/slub.c:3960!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
...
(kfree) from [<c058e8c0>] (platform_set_driver_override+0x84/0xac)
(platform_set_driver_override) from [<c058e908>] (driver_override_store+0x20/0x34)
(driver_override_store) from [<c031f778>] (kernfs_fop_write+0x100/0x1dc)
(kernfs_fop_write) from [<c0296de8>] (__vfs_write+0x2c/0x17c)
(__vfs_write) from [<c02970c4>] (vfs_write+0xa4/0x188)
(vfs_write) from [<c02972e8>] (ksys_write+0x4c/0xac)
(ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x28)
The clk-exynos5-subcmu driver uses override only for the purpose of
creating meaningful names for children devices (matching names of power
domains, e.g. DISP, MFC). The driver_override was not developed for
this purpose so just switch to default names of devices to fix the
issue.
Fixes: b06a532bf1 ("clk: samsung: Add Exynos5 sub-CMU clock driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f0b6216ea upstream.
During initialization of subdevices if platform_device_alloc() failed,
returned NULL pointer will be later dereferenced. Add proper error
paths to exynos5_clk_register_subcmu(). The return value of this
function is still ignored because at this stage of init there is nothing
we can do.
Fixes: b06a532bf1 ("clk: samsung: Add Exynos5 sub-CMU clock driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ae51d67ae upstream.
I noticed that modprobe clk-twl6040 can fail after a cold boot with:
abe_cm:clk:0010:0: failed to enable
...
Unhandled fault: imprecise external abort (0x1406) at 0xbe896b20
WARNING: CPU: 1 PID: 29 at drivers/clk/clk.c:828 clk_core_disable_lock+0x18/0x24
...
(clk_core_disable_lock) from [<c0123534>] (_disable_clocks+0x18/0x90)
(_disable_clocks) from [<c0124040>] (_idle+0x17c/0x244)
(_idle) from [<c0125ad4>] (omap_hwmod_idle+0x24/0x44)
(omap_hwmod_idle) from [<c053a038>] (sysc_runtime_suspend+0x48/0x108)
(sysc_runtime_suspend) from [<c06084c4>] (__rpm_callback+0x144/0x1d8)
(__rpm_callback) from [<c0608578>] (rpm_callback+0x20/0x80)
(rpm_callback) from [<c0607034>] (rpm_suspend+0x120/0x694)
(rpm_suspend) from [<c0607a78>] (__pm_runtime_idle+0x60/0x84)
(__pm_runtime_idle) from [<c053aaf0>] (sysc_probe+0x874/0xf2c)
(sysc_probe) from [<c05fecd4>] (platform_drv_probe+0x48/0x98)
After searching around for a similar issue, I came across an earlier fix
that never got merged upstream in the Android tree for glass-omap-xrr02.
There is patch "MFD: twl6040-codec: Implement PDMCLK cold temp errata"
by Misael Lopez Cruz <misael.lopez@ti.com>.
Based on my observations, this fix is also needed when cold booting
devices, and not just for deeper idle modes. Since we now have a clock
driver for pdmclk, let's fix the issue in twl6040_pdmclk_prepare().
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ee0b27a3a4 ]
According to the manual the gate clock for MMC3 is at bit 11, and NAND1
is controlled by bit 12.
Fix the gate bit definitions in the clock driver.
Fixes: c6e6c96d8f ("clk: sunxi-ng: Add A31/A31s clocks")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c59801f70 ]
According to the datasheet and the reference code from Allwinner, the
bit used to de-assert the TCON reset is bit 4, not bit 3.
Fix it in the V3s CCU driver.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ff1a3b491 ]
The clocks of the CPUSS such as "gcc_cpuss_ahb_clk_src" is a CRITICAL
clock and needs to vote on the active only source of XO, so as to keep
the vote as long as CPUSS is active. Similar rbcpr_clk_src is also has
the same requirement.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Fixes: 06391eddb6 ("clk: qcom: Add Global Clock controller (GCC) driver for SDM845")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 303aef8b84 ]
The ti_clk_parse_divider_data() function is only called from
_get_div_table_from_setup(). That function doesn't look at the return
value but instead looks at the "*table" pointer. In this case, if the
kcalloc() fails then *table is NULL (which means success). It should
instead be an error pointer.
The ti_clk_parse_divider_data() function has two callers. One checks
for errors and the other doesn't. I have fixed it so now both handle
errors.
Fixes: 4f6be5655d ("clk: ti: divider: add driver internal API for parsing divider data")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2137a109a5 ]
In case the upstream clock are not set, which can happen in case the
VC5 has no valid upstream clock, the $src variable is used uninited
by regmap_update_bits(). Check for this condition and return -EINVAL
in such case.
Note that in case the VC5 has no valid upstream clock, the VC5 can
not operate correctly. That is a hardware property of the VC5. The
internal oscilator present in some VC5 models is also considered
upstream clock.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Alexey Firago <alexey_firago@mentor.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-renesas-soc@vger.kernel.org
[sboyd@kernel.org: Added comment about probe preventing this from
happening in the first place]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d39eca547f ]
If tegra_dfll_unregister() fails then "soc" is an error pointer. We
should just return instead of dereferencing it.
Fixes: 1752c9ee23 ("clk: tegra: dfll: Fix drvdata overwriting issue")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0efcc2c0fd ]
Same as other i.MX6 SoCs, ensure unused MMDC channel's
handshake is bypassed, this is to make sure no request
signal will be generated when periphe_clk_sel is changed
or SRC warm reset is triggered.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e6da2039c ]
All the audio interfaces on Allwinner SoCs need to change their module
clocks during operation, to switch between support for 44.1 kHz and 48
kHz family sample rates. The clock rate for the module clocks is
governed by their upstream audio PLL. The module clocks themselves only
have a gate, and sometimes a divider or mux. Thus any rate changes need
to be propagated upstream.
Set the CLK_SET_RATE_PARENT flag for all audio module clocks to achieve
this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0dad1ec65b ]
We don't want the common clock framework to disable the "cpu_clk" if
it's not used by any device. The cpufreq-dt driver does not enable the
CPU clocks. However, even if it would we would still want the CPU clock
to be enabled at all times because the CPU clock is also required even
if we disable CPU frequency scaling on a specific board.
The reason why we want the CPU clock to be enabled is a clock further up
in the tree:
Since commit 6f888e7bc7bd58 ("clk: meson: clk-pll: add enable bit") the
sys_pll can be disabled. However, since the CPU clock is derived from
sys_pll we don't want sys_pll to get disabled. The common clock
framework takes care of that for us by enabling all parent clocks of our
CPU clock when we mark the CPU clock with CLK_IS_CRITICAL.
Until now this is not a problem yet because all clocks in the CPU
clock's tree (including sys_pll) are read-only. However, once we allow
modifications to the clocks in that tree we will need this.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20181115224048.13511-4-martin.blumenstingl@googlemail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8662eadd1 ]
According to the public S805 datasheet HHI_SYS_CPU_CLK_CNTL1[29:20] is
the register for the CPU scale_div clock. This matches the code in
Amlogic's 3.10 GPL kernel sources:
N = (aml_read_reg32(P_HHI_SYS_CPU_CLK_CNTL1) >> 20) & 0x3FF;
This means that the divider register is 10 bit wide instead of 9 bits.
So far this is not a problem since all u-boot versions I have seen are
not using the cpu_scale_div clock at all (instead they are configuring
the CPU clock to run off cpu_in_sel directly).
The fixes tag points to the latest rework of the CPU clocks. However,
even before the rework it was wrong. Commit 7a29a86943 ("clk: meson:
Add support for Meson clock controller") defines MESON_N_WIDTH as 9 (in
drivers/clk/meson/clk-cpu.c). But since the old clk-cpu implementation
this only carries the fixes tag for the CPU clock rewordk.
Fixes: 251b6fd38b ("clk: meson: rework meson8b cpu clock")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20180927085921.24627-3-martin.blumenstingl@googlemail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5ac1ead32 ]
The cpu_div3 clock (cpu_in divided by 3) generates a signal with a duty
cycle of 33%. The CPU clock however requires a clock signal with a duty
cycle of 50% to run stable.
cpu_div3 was observed to be problematic when cycling through all
available CPU frequencies (with additional patches on top of this one)
while running "stress --cpu 4" in the background. This caused sporadic
hangs where the whole system would fully lock up.
Amlogic's 3.10 kernel code also does not use the cpu_div3 clock either
when changing the CPU clock.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20181115224048.13511-3-martin.blumenstingl@googlemail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46fda5b506 ]
Smatch report warnings:
drivers/clk/imgtec/clk-boston.c:76 clk_boston_setup() warn: possible memory leak of 'onecell'
drivers/clk/imgtec/clk-boston.c:83 clk_boston_setup() warn: possible memory leak of 'onecell'
drivers/clk/imgtec/clk-boston.c:90 clk_boston_setup() warn: possible memory leak of 'onecell'
'onecell' is malloced in clk_boston_setup(), but not be freed
before leaving from the error handling cases.
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b488517b28 upstream.
The fixed clocks in the DTS file have a hyphen, but the clock driver has
the fixed clocks using underbar. Thus the clock driver cannot detect the
other fixed clocks correctly. Change the fixed clock names to a hyphen.
Fixes: 07afb8db73 ("clk: socfpga: stratix10: add clock driver for
Stratix10 platform")
Cc: linux-stable@vger.kernel.org
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f7542d8177 ]
The exclusive gates may be set up in the wrong way by software running
before the clock driver comes up. In that case the exclusive setup is
locked in its initial state, as the complementary function can't be
activated without disabling the initial setup first.
To avoid this lock situation, reset the exclusive gates to the off
state and allow the kernel to provide the proper setup.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Dong Aisheng <Aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e5ef7a57c ]
As the commit 2893c37946 ("clk: make strings in parent name arrays
const"), let's make the parent strings const, otherwise we may meet
the following warning when compiling:
drivers/clk/imx/clk-imx7ulp.c: In function 'imx7ulp_clocks_init':
drivers/clk/imx/clk-imx7ulp.c:73:35: warning: passing argument 5 of
'imx_clk_mux_flags' discards 'const' qualifier from pointer target type
clks[IMX7ULP_CLK_APLL_PRE_SEL] = imx_clk_mux_flags("apll_pre_sel", base + 0x508, 0,
1, pll_pre_sels, ARRAY_SIZE(pll_pre_sels), CLK_SET_PARENT_GATE);
^
In file included from drivers/clk/imx/clk-imx7ulp.c:23:0:
drivers/clk/imx/clk.h:200:27: note: expected 'const char **' but argument is
of type 'const char * const*'
...
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad9b2b8e53 ]
The public S805 datasheet only mentions that
HHI_SYS_CPU_CLK_CNTL1[20:29] contains a divider called "cpu_scale_div".
Unfortunately it does not mention how to use the register contents.
The Amlogic 3.10 GPL kernel sources are using the following code to
calculate the CPU clock based on that register (taken from
arch/arm/mach-meson8/clock.c in the 3.10 Amlogic kernel, shortened to
make it easier to read):
N = (aml_read_reg32(P_HHI_SYS_CPU_CLK_CNTL1) >> 20) & 0x3FF;
if (sel == 3) /* use cpu_scale_div */
div = 2 * N;
else
div = ... /* not relevant for this example */
cpu_clk = parent_clk / div;
This suggests that the formula is: parent_rate / 2 * register_value
However, running perf (which can measure the CPU clock rate thanks to
the ARM PMU) shows that this formula is not correct.
This can be reproduced with the following steps:
1. boot into u-boot
2. let the CPU clock run off the XTAL clock:
mw.l 0xC110419C 0x30 1
3. set the cpu_scale_div register:
to value 0x1: mw.l 0xC110415C 0x801016A2 1
to value 0x2: mw.l 0xC110415C 0x802016A2 1
to value 0x5: mw.l 0xC110415C 0x805016A2 1
4. let the CPU clock run off cpu_scale_div:
mw.l 0xC110419C 0xbd 1
5. boot Linux
6. run: perf stat -aB stress --cpu 4 --timeout 10
7. check the "cycles" value
I get the following results depending on the cpu_scale_div value:
- (cpu_in_sel - this is the input clock for cpu_scale_div - runs at
1.2GHz)
- 0x1 = 300MHz
- 0x2 = 200MHz
- 0x5 = 100MHz
This means that the actual formula to calculate the output of the
cpu_scale_div clock is: parent_rate / 2 * (register value + 1).
The register value 0x0 is reserved. When letting the CPU clock run off
the cpu_scale_div while the value is 0x0 the whole board hangs (even in
u-boot).
I also verified this with the TWD timer: when adding this to the .dts
without specifying it's clock it will auto-detect the PERIPH (which is
the input clock of the TWD) clock rate (and the result is shown in the
kernel log). On Meson8, Meson8b and Meson8m2 the PERIPH clock is CPUCLK
divided by 4. This also matched for all three test-cases from above (in
all cases the TWD timer clock rate was approx. one fourth of the CPU
clock rate).
A small note regarding the "fixes" tag: the original issue seems to
exist virtually since forever. Even commit 28b9fcd016 ("clk:
meson8b: Add support for Meson8b clocks") seems to handle this wrong. I
still decided to use commit 251b6fd38b ("clk: meson: rework meson8b
cpu clock") because this is the first commit which gets the CPU hiearchy
correct and thus it's the first commit where the cpu_scale_div register
is used correctly (apart from the bug in the cpu_scale_table).
Fixes: 251b6fd38b ("clk: meson: rework meson8b cpu clock")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20180927085921.24627-2-martin.blumenstingl@googlemail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 65b6657672 upstream.
Allwinner H6 SoC has multiplier N range between 1 and 254. Since parent
rate is 24MHz, intermediate result when calculating final rate easily
overflows 32 bit variable.
Because of that, introduce function for calculating clock rate which
uses 64 bit variable for intermediate result.
Fixes: 6174a1e24b ("clk: sunxi-ng: Add N-M-factor clock support")
Fixes: ee28648cb2 ("clk: sunxi-ng: Remove the use of rational computations")
CC: <stable@vger.kernel.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2e85c57493 ]
The > comparison should be >= or we write one element beyond the end of
the unit->clk_table[] array.
(The unit->clk_table[] array is allocated in the mmp_clk_init() function
and it has unit->nr_clks elements).
Fixes: 4661fda10f ("clk: mmp: add basic support functions for DT support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9f5b7f5dd ]
These > comparisons should be >= to prevent reading beyond the end of
of the clk_data->hws[] buffer.
The clk_data->hws[] array is allocated in cp110_syscon_common_probe()
when we do:
cp110_clk_data = devm_kzalloc(dev, sizeof(*cp110_clk_data) +
sizeof(struct clk_hw *) * CP110_CLK_NUM,
GFP_KERNEL);
As you can see, it has CP110_CLK_NUM elements which is equivalent to
CP110_MAX_CORE_CLOCKS + CP110_MAX_GATABLE_CLOCKS.
Fixes: d3da3eaef7 ("clk: mvebu: new driver for Armada CP110 system controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f98e8a572b ]
When the fixed factor clock is created by devicetree,
of_clk_add_provider is called. Add a call to
of_clk_del_provider in the remove function to balance
it out.
Reported-by: Alan Tull <atull@kernel.org>
Fixes: 971451b3b1 ("clk: fixed-factor: Convert into a module platform driver")
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 00a461cc32 ]
Fix child-node lookup which by using the wrong OF helper was searching
the whole tree depth-first, something which could end up matching an
unrelated node.
Also fix the related node-reference leaks.
Fixes: 5b385a45e0 ("clk: ti: add support for clkctrl aliases")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee02950d53 ]
The clock for UARTs 0 through 2 is UART012, the clock for UARTs 3 through
7 is UART34567.
For UART012, we stop the clock driver from changing the clock rate. This
is because the Synopsys UART driver simply sets the reference clock to 16x
the baud rate, but doesn't check if the actual rate is within the required
tolerance. The RZ/N1 clock divider can't provide this (we have to rely on
the UART's internal divider to set the correct clock rate), so you end up
with a clock rate that is way off what you wanted.
In addition, since the clock is shared between multiple UARTs, you don't
want the driver trying to change the clock rate as it may affect the other
UARTs (which may not have been configured yet, so you don't know what baud
rate they will use). Normally, the clock rate is set early on before Linux
to some very high rate that supports all of the clock rates you want.
This change stops the UART34567 clock rate from changing for the same
reasons.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Fixes: 4c3d88526e ("clk: renesas: Renesas R9A06G032 clock driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2303a9ca69 ]
CLK_GET_RATE_NOCACHE should only be necessary when the registers
controlling the rate of clock may change outside of CCF. On Amlogic,
it should only be the case for the hdmi pll which is directly controlled
by the display driver (WIP to fix this).
The other plls should not require this flag.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69b93104c7 ]
We found the PCIe driver doesn't really work with
the mpll3 clock which is actually reserved for debug,
So drop it from the mux list.
Fixes: 33b89db68236 ("clk: meson-axg: add clocks required by pcie driver")
Tested-by: Jianxin Qin <jianxin.qin@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52091c256b ]
When the fixed rate clock is created by devicetree,
of_clk_add_provider is called. Add a call to
of_clk_del_provider in the remove function to balance
it out.
Signed-off-by: Alan Tull <atull@kernel.org>
Fixes: 435779fe13 ("clk: fixed-rate: Convert into a module platform driver")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e9a2310fb6 upstream.
There is a potential execution path in which function
platform_get_resource() returns NULL. If this happens,
we will end up having a NULL pointer dereference.
Fix this by replacing devm_ioremap with devm_ioremap_resource,
which has the NULL check and the memory region request.
This code was detected with the help of Coccinelle.
Cc: stable@vger.kernel.org
Fixes: 97b7129cd2 ("reset: hisilicon: change the definition of hisi_reset_init")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 665636b294 upstream.
Fixes the signedness bug returning '(-22)' on the return type by removing the
sanity checker in rockchip_ddrclk_get_parent(). The function should return
and unsigned value only and it's safe to remove the sanity checker as the
core functions that call get_parent like clk_core_get_parent_by_index already
ensures the validity of the clk index returned (index >= core->num_parents).
Fixes: a4f182bf81 ("clk: rockchip: add new clock-type for the ddrclk")
Cc: stable@vger.kernel.org
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2852bfbf4f upstream.
The bus clocks (AHB/APB) on Allwinner H6 have their second divider start
at bit 8, according to the user manual and the BSP code. However,
currently the divider offset is incorrectly set to 16, thus the divider
is not correctly read and the clock frequency is not correctly calculated.
Fix this bit offset on all affected bus clocks in ccu-sun50i-h6.
Cc: stable@vger.kernel.org # v4.17.y
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f5cb0e622 upstream.
Commit a982e45dc1 ("clk: at91: PLL recalc_rate() now using cached MUL
and DIV values") removed a check that prevents a division by zero. This
now causes a stacktrace when booting the kernel on a at91 platform if
the PLL DIV register contains zero. This commit reintroduces this check.
Fixes: a982e45dc1 ("clk: at91: PLL recalc_rate() now using cached...")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ronald Wahl <rwahl@gmx.de>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8985167ecf upstream.
When driver is built as module and DT node contains clocks compatible
(e.g. "samsung,s2mps11-clk"), the module will not be autoloaded because
module aliases won't match.
The modalias from uevent: of:NclocksT<NULL>Csamsung,s2mps11-clk
The modalias from driver: platform:s2mps11-clk
The devices are instantiated by parent's MFD. However both Device Tree
bindings and parent define the compatible for clocks devices. In case
of module matching this DT compatible will be used.
The issue will not happen if this is a built-in (no need for module
matching) or when clocks DT node does not contain compatible (not
correct from bindings perspective but working for driver).
Note when backporting to stable kernels: adjust the list of device ID
entries.
Cc: <stable@vger.kernel.org>
Fixes: 53c31b3437 ("mfd: sec-core: Add of_compatible strings for clock MFD cells")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d6ee1e7e90 ]
Similar to gxbb and gxl platforms, axg SCPI Cortex-M co-processor
uses the fdiv2 and fdiv3 to, among other things, provide the cpu
clock.
Until clock hand-off mechanism makes its way to CCF and the generic
SCPI claims platform specific clocks, these clocks must be marked as
critical to make sure they are never disabled when needed by the
co-processor.
Fixes: 05f814402d ("clk: meson: add fdiv clock gates")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
