I2C busses can be assigned specific bus numbers using aliases in
Device Tree - string properties where the name is the alias and the
value is the path to the node. The current DT parameter mechanism
does not allow property names to be derived from a parameter value
in any way, so it isn't possible to generate unique or matching
aliases for nodes from an overlay that can generate multiple
instances, e.g. i2c-gpio.
Work around this limitation (at least temporarily) by allowing
the i2c adapter number to be initialised from the "reg" property
if present.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
i2c-bcm2708: fixed baudrate
Fixed issue where the wrong CDIV value was set for baudrates below 3815 Hz (for 250MHz bus clock).
In that case the computed CDIV value was more than 0xffff. However the CDIV register width is only 16 bits.
This resulted in incorrect setting of CDIV and higher baudrate than intended.
Example: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0x1704 -> 42430Hz
After correction: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0xffff -> 3815Hz
The correct baudrate is shown in the log after the cdiv > 0xffff correction.
Perform I2C combined transactions when possible
Perform I2C combined transactions whenever possible, within the
restrictions of the Broadcomm Serial Controller.
Disable DONE interrupt during TA poll
Prevent interrupt from being triggered if poll is missed and transfer
starts and finishes.
i2c: Make combined transactions optional and disabled by default
i2c: bcm2708: add device tree support
Add DT support to driver and add to .dtsi file.
Setup pins in .dts file.
i2c is disabled by default.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
bcm2708: don't register i2c controllers when using DT
The devices for the i2c controllers are in the Device Tree.
Only register devices when not using DT.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
I2C: Only register the I2C device for the current board revision
i2c_bcm2708: Fix clock reference counting
Fix grabbing lock from atomic context in i2c driver
2 main changes:
- check for timeouts in the bcm2708_bsc_setup function as indicated by this comment:
/* poll for transfer start bit (should only take 1-20 polls) */
This implies that the setup function can now fail so account for this everywhere it's called
- Removed the clk_get_rate call from inside the setup function as it locks a mutex and that's not ok since we call it from under a spin lock.
i2c-bcm2708: When using DT, leave the GPIO setup to pinctrl
i2c-bcm2708: Increase timeouts to allow larger transfers
Use the timeout value provided by the I2C_TIMEOUT ioctl when waiting
for completion. The default timeout is 1 second.
See: https://github.com/raspberrypi/linux/issues/260
i2c-bcm2708/BCM270X_DT: Add support for I2C2
The third I2C bus (I2C2) is normally reserved for HDMI use. Careless
use of this bus can break an attached display - use with caution.
It is recommended to disable accesses by VideoCore by setting
hdmi_ignore_edid=1 or hdmi_edid_file=1 in config.txt.
The interface is disabled by default - enable using the
i2c2_iknowwhatimdoing DT parameter.
bcm2708-spi: Don't use static pin configuration with DT
Also remove superfluous error checking - the SPI framework ensures the
validity of the chip_select value.
i2c-bcm2708: Remove non-DT support
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Set the BSC_CLKT clock streching timeout to 35ms as per SMBus specs.
Fixes i2c_bcm2708: Write to FIFO correctly - v2 (#1574)
* i2c: fix i2c_bcm2708: Clear FIFO before sending data
Make sure FIFO gets cleared before trying to send
data in case of a repeated start (COMBINED=Y).
* i2c: fix i2c_bcm2708: Only write to FIFO when not full
Check if FIFO can accept data before writing.
To avoid a peripheral read on the last iteration of a loop,
both bcm2708_bsc_fifo_fill and ~drain are changed as well.
This adds a debug module parameter to aid in debugging transfer issues
by printing info to the kernel log. When enabled, status values are
collected in the interrupt routine and msg info in
bcm2835_i2c_start_transfer(). This is done in a way that tries to avoid
affecting timing. Having printk in the isr can mask issues.
debug values (additive):
1: Print info on error
2: Print info on all transfers
3: Print messages before transfer is started
The value can be changed at runtime:
/sys/module/i2c_bcm2835/parameters/debug
Example output, debug=3:
[ 747.114448] bcm2835_i2c_xfer: msg(1/2) write addr=0x54, len=2 flags= [i2c1]
[ 747.114463] bcm2835_i2c_xfer: msg(2/2) read addr=0x54, len=32 flags= [i2c1]
[ 747.117809] start_transfer: msg(1/2) write addr=0x54, len=2 flags= [i2c1]
[ 747.117825] isr: remain=2, status=0x30000055 : TA TXW TXD TXE [i2c1]
[ 747.117839] start_transfer: msg(2/2) read addr=0x54, len=32 flags= [i2c1]
[ 747.117849] isr: remain=32, status=0xd0000039 : TA RXR TXD RXD [i2c1]
[ 747.117861] isr: remain=20, status=0xd0000039 : TA RXR TXD RXD [i2c1]
[ 747.117870] isr: remain=8, status=0x32 : DONE TXD RXD [i2c1]
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
commit f4e3f4ae1d upstream.
Tegra186 and prior supports maximum 4K bytes per packet transfer
including 12 bytes of packet header.
This patch fixes max write length limit to account packet header
size for transfers.
Cc: stable@vger.kernel.org # 4.4+
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f275a46594 ]
The driver's interrupt handler checks whether a message is currently
being handled with the curr_msg pointer. When it is NULL, the interrupt
is considered to be unexpected. Similarly, the i2c_start_transfer
routine checks for the remaining number of messages to handle in
num_msgs.
However, these values are never cleared and always keep the message and
number relevant to the latest transfer (which might be done already and
the underlying message memory might have been freed).
When an unexpected interrupt hits with the DONE bit set, the isr will
then try to access the flags field of the curr_msg structure, leading
to a fatal page fault.
The msg_buf and msg_buf_remaining fields are also never cleared at the
end of the transfer, which can lead to similar pitfalls.
Fix these issues by introducing a cleanup function and always calling
it after a transfer is finished.
Fixes: e247454103 ("i2c: bcm2835: Fix hang for writing messages larger than 16 bytes")
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d358def706 ]
In case the hold bit is not needed we are carrying the old values.
Fix the same by resetting the bit when not needed.
Fixes the sporadic i2c bus lockups on National Instruments
Zynq-based devices.
Fixes: df8eb5691c ("i2c: Add driver for Cadence I2C controller")
Reported-by: Kyle Roeschley <kyle.roeschley@ni.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Tested-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6e2bd9569 ]
We currently get the following error with pixcir_ts driver during a
suspend resume cycle:
omap_i2c 4802a000.i2c: controller timed out
pixcir_ts 1-005c: pixcir_int_enable: can't read reg 0x34 : -110
pixcir_ts 1-005c: Failed to disable interrupt generation: -110
pixcir_ts 1-005c: Failed to stop
dpm_run_callback(): pixcir_i2c_ts_resume+0x0/0x98
[pixcir_i2c_ts] returns -110
PM: Device 1-005c failed to resume: error -110
And at least am437x based devices with pixcir_ts will fail to resume
to a touchscreen that is configured as the wakeup-source in device
tree for these devices.
This is because pixcir_ts tries to reconfigure it's registers for
noirq suspend which fails. This also leaves i2c-omap in enabled state
for suspend.
Let's fix the pixcir_ts issue and make sure i2c-omap is suspended by
adding SET_NOIRQ_SYSTEM_SLEEP_PM_OPS.
Let's also get rid of some ifdefs while at it and replace them with
__maybe_unused as SET_RUNTIME_PM_OPS and SET_NOIRQ_SYSTEM_SLEEP_PM_OPS
already deal with the various PM Kconfig options.
Reported-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51243b7345 ]
Similarly to R-Car E3, RZ/G2E doesn't come with automatic
transmission registers, as such it is not considered compatible
with the existing fallback bindings.
Add SoC specific binding compatibility to allow for later
support for automatic transmission.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f5c85fe3a ]
It was observed that when using seqentional mode contrary to the
documentation, the SS bit (which is supposed to only be set if
automatic/sequence command completed normally), is sometimes set
together with NA (NAK in address phase) causing transfer to falsely be
considered successful.
My assumption is that this does not happen during manual mode since the
controller is stopping its work the moment it sets NA/ND bit in status
register. This is not the case in Automatic/Sequentional mode where it
is still working to send STOP condition and the actual status we get
depends on the time when the ISR is run.
This patch changes the order of checking status bits in ISR - error
conditions are checked first and only if none of them occurred, the
transfer may be considered successful. This is required to introduce
using of sequentional mode in next patch.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5eb316e636 ]
Add support for the IIC code for the r8a77990 (R-Car E3).
It is not considered compatible with existing fallback bindings
due to the documented absence of automatic transmission registers.
These registers are currently not used by the driver and
thus the provides the same behaviour for "renesas,iic-r8a77990" and
"renesas,rcar-gen3-iic". The point of declaring incompatibility is
to allow for automatic transmission register support to be added to
"renesas,iic-r8a77990" and "renesas,rcar-gen3-iic" in future.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6ebec961d5 upstream.
If adapter->retries is set to a minus value from user space via ioctl,
it will make __i2c_transfer and __i2c_smbus_xfer skip the calling to
adapter->algo->master_xfer and adapter->algo->smbus_xfer that is
registered by the underlying bus drivers, and return value 0 to all the
callers. The bus driver will never be accessed anymore by all users,
besides, the users may still get successful return value without any
error or information log print out.
If adapter->timeout is set to minus value from user space via ioctl,
it will make the retrying loop in __i2c_transfer and __i2c_smbus_xfer
always break after the the first try, due to the time_after always
returns true.
Signed-off-by: Yi Zeng <yizeng@asrmicro.com>
[wsa: minor grammar updates to commit message]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ece27a337d ]
Currently, the clock duty is set as tLOW/tHIGH = 1/1. For Fast-mode,
tLOW is set to 1.25 us while the I2C spec requires tLOW >= 1.3 us.
tLOW/tHIGH = 5/4 would meet both Standard-mode and Fast-mode:
Standard-mode: tLOW = 5.56 us, tHIGH = 4.44 us
Fast-mode: tLOW = 1.39 us, tHIGH = 1.11 us
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8469636ab5 ]
Currently, the clock duty is set as tLOW/tHIGH = 1/1. For Fast-mode,
tLOW is set to 1.25 us while the I2C spec requires tLOW >= 1.3 us.
tLOW/tHIGH = 5/4 would meet both Standard-mode and Fast-mode:
Standard-mode: tLOW = 5.56 us, tHIGH = 4.44 us
Fast-mode: tLOW = 1.39 us, tHIGH = 1.11 us
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0544ee4b1a ]
Some AMD based HP laptops have a SMB0001 ACPI device node which does not
define any methods.
This leads to the following error in dmesg:
[ 5.222731] cmi: probe of SMB0001:00 failed with error -5
This commit makes acpi_smbus_cmi_add() return -ENODEV instead in this case
silencing the error. In case of a failure of the i2c_add_adapter() call
this commit now propagates the error from that call instead of -EIO.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c7f25cae5 ]
According to Intel (R) Axxia TM Lionfish Communication Processor
Peripheral Subsystem Hardware Reference Manual, the AXXIA I2C module
have a programmable Master Wait Timer, which among others, checks the
time between commands send in manual mode. When a timeout (25ms) passes,
TSS bit is set in Master Interrupt Status register and a Stop command is
issued by the hardware.
The axxia_i2c_xfer(), does not properly handle this situation, however.
For each message a separate axxia_i2c_xfer_msg() is called and this
function incorrectly assumes that any interrupt might happen only when
waiting for completion. This is mostly correct but there is one
exception - a master timeout can trigger if enough time has passed
between individual transfers. It will, by definition, happen between
transfers when the interrupts are disabled by the code. If that happens,
the hardware issues Stop command.
The interrupt indicating timeout will not be triggered as soon as we
enable them since the Master Interrupt Status is cleared when master
mode is entered again (which happens before enabling irqs) meaning this
error is lost and the transfer is continued even though the Stop was
issued on the bus. The subsequent operations completes without error but
a bogus value (0xFF in case of read) is read as the client device is
confused because aborted transfer. No error is returned from
master_xfer() making caller believe that a valid value was read.
To fix the problem, the TSS bit (indicating timeout) in Master Interrupt
Status register is checked before each transfer. If it is set, there was
a timeout before this transfer and (as described above) the hardware
already issued Stop command so the transaction should be aborted thus
-ETIMEOUT is returned from the master_xfer() callback. In order to be
sure no timeout was issued we can't just read the status just before
starting new transaction as there will always be a small window of time
(few CPU cycles at best) where this might still happen. For this reason
we have to temporally disable the timer before checking for TSS bit.
Disabling it will, however, clear the TSS bit so in order to preserve
that information, we have to read it in ISR so we have to ensure that
the TSS interrupt is not masked between transfers of one transaction.
There is no need to call bus recovery or controller reinitialization if
that happens so it's skipped.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b57436f15 ]
We should check the bus state before reinitializing the IP core.
Otherwise, the internal bus busy state which also tracks multi-master
activity is lost.
Credits go to the Renesas BSP team for suggesting this change.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Fixes: ae481cc139 ("i2c: rcar: fix resume by always initializing registers before transfer")
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Upstream commit 3e9efc3299 ("i2c: aspeed: Handle master/slave combined irq events
properly") reworked the interrupt handling and fixed a warning in the process:
drivers/i2c/busses/i2c-aspeed.c: In function 'aspeed_i2c_bus_irq':
drivers/i2c/busses/i2c-aspeed.c:567:1: error: label 'out' defined but not used [-Werror=unused-label]
The warning is still present in v4.19.8 and can be fixed either by applying
that original patch, or by adding a simple #ifdef.
Here, I choose the second simpler option as the original patch seems too
invasive for a stable backport.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 848bd3f3de ]
We need to enable runtime PM on this i2c controller before populating
child devices with i2c_add_adapter(). Otherwise, if a child device uses
runtime PM and stays runtime PM enabled we'll get the following warning
at boot.
Enabling runtime PM for inactive device (a98000.i2c) with active children
[...]
Call trace:
pm_runtime_enable+0xd8/0xf8
geni_i2c_probe+0x440/0x460
platform_drv_probe+0x74/0xc8
[...]
Let's move the runtime PM enabling and setup to before we add the
adapter, so that this device can respond to runtime PM requests from
children.
Fixes: 37692de5d5 ("i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
DMA needs to be cleaned up not only on timeout, but on all errors where
it has been setup before.
Fixes: 73e8b05283 ("i2c: rcar: add DMA support")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This function was renamed in commit 82fe39a6bc ("i2c: refactor
function to release a DMA safe buffer") but this kernel doc wasn't
updated to point at the new function. Rename it.
Fixes: 82fe39a6bc ("i2c: refactor function to release a DMA safe buffer")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There are platforms which don't provide input clock rate but provide
I2C timing parameters. Commit 3bd4f27727 ("i2c: designware: Call
i2c_dw_clk_rate() only once in i2c_dw_init_master()") causes needless
warning during probe on those platforms since i2c_dw_clk_rate(), which
causes the warning when input clock is unknown, is called even when
there is no need to calculate timing parameters.
Fixes: 3bd4f27727 ("i2c: designware: Call i2c_dw_clk_rate() only once in i2c_dw_init_master()")
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: <stable@vger.kernel.org> # 4.19
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c-scmi driver crashes when the SMBus Write Block transaction is
executed:
WARNING: CPU: 9 PID: 2194 at mm/page_alloc.c:3931 __alloc_pages_slowpath+0x9db/0xec0
Call Trace:
? get_page_from_freelist+0x49d/0x11f0
? alloc_pages_current+0x6a/0xe0
? new_slab+0x499/0x690
__alloc_pages_nodemask+0x265/0x280
alloc_pages_current+0x6a/0xe0
kmalloc_order+0x18/0x40
kmalloc_order_trace+0x24/0xb0
? acpi_ut_allocate_object_desc_dbg+0x62/0x10c
__kmalloc+0x203/0x220
acpi_os_allocate_zeroed+0x34/0x36
acpi_ut_copy_eobject_to_iobject+0x266/0x31e
acpi_evaluate_object+0x166/0x3b2
acpi_smbus_cmi_access+0x144/0x530 [i2c_scmi]
i2c_smbus_xfer+0xda/0x370
i2cdev_ioctl_smbus+0x1bd/0x270
i2cdev_ioctl+0xaa/0x250
do_vfs_ioctl+0xa4/0x600
SyS_ioctl+0x79/0x90
do_syscall_64+0x73/0x130
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
ACPI Error: Evaluating _SBW: 4 (20170831/smbus_cmi-185)
This problem occurs because the length of ACPI Buffer object is not
defined/initialized in the code before a corresponding ACPI method is
called. The obvious patch below fixes this issue.
Signed-off-by: Edgar Cherkasov <echerkasov@dev.rtsoft.ru>
Acked-by: Viktor Krasnov <vkrasnov@dev.rtsoft.ru>
Acked-by: Michael Brunner <Michael.Brunner@kontron.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We shouldn't attempt to DMA map the message buffers passed into this
driver from the i2c core unless the message we're mapping have been
properly setup for DMA. The i2c core indicates such a situation by
setting the I2C_M_DMA_SAFE flag, so check for that flag before using DMA
mode. We can also bounce the buffer if it isn't already mapped properly
by using the i2c_get_dma_safe_msg_buf() APIs, so do that when we
want to use DMA for a message.
This fixes a problem where the kernel oopses cleaning pages for a buffer
that's mapped into the vmalloc space. The pages are returned from
request_firmware() and passed down directly to the i2c master to write
to the i2c touchscreen device. Mapping vmalloc buffers with
dma_map_single() won't work reliably, causing an oops like below:
Unable to handle kernel paging request at virtual address ffffffc01391d000
...
Reported-by: Philip Chen <philipchen@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Disable interrupts while configuring the transfer and enable them back.
We have below as the programming sequence
1. start and slave address
2. byte count and stop
In some customer platform there was a lot of interrupts between 1 and 2
and after slave address (around 7 clock cyles) if 2 is not executed
then the transaction is nacked.
To fix this case make the 2 writes atomic.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[wsa: added a newline for better readability]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
DNV's iTCO is slightly different with SMBCTRL sitting at a different
offset when compared to all other devices. Let's fix so that we can
properly use iTCO watchdog.
Fixes: 84d7f2ebd7 ("i2c: i801: Add support for Intel DNV")
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
mx8dv never entered into production and there is no other place
in the kernel referring to this SoC, so remove it from the
driver's compatible entry.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver currently emits a STOP if the next message is not
I2C_MD_RD. It should not do it because it disturbs the I2C_RDWR
ioctl, where read/write transactions are combined without STOP
between.
Issue STOP only when the message is the last one _or_ flagged with
I2C_M_STOP.
Fixes: 6a62974b66 ("i2c: uniphier_f: add UniPhier FIFO-builtin I2C driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver currently emits a STOP if the next message is not
I2C_MD_RD. It should not do it because it disturbs the I2C_RDWR
ioctl, where read/write transactions are combined without STOP
between.
Issue STOP only when the message is the last one _or_ flagged with
I2C_M_STOP.
Fixes: dd6fd4a327 ("i2c: uniphier: add UniPhier FIFO-less I2C driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We only freed the bounce buffer after successful DMA, missing the cases
where DMA setup may have gone wrong. Use a better location which always
gets called after each message and use 'stop_after_dma' as a flag for a
successful transfer.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
After various refactoring over the years, start_ch() doesn't return
errno anymore, so make the function return void. This saves the error
handling when calling it which in turn eases cleanup of resources of a
future patch.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
a) rename to 'put' instead of 'release' to match 'get' when obtaining
the buffer
b) change the argument order to have the buffer as first argument
c) add a new argument telling the function if the message was
transferred. This allows the function to be used also in cases
where setting up DMA failed, so the buffer needs to be freed without
syncing to the message buffer.
Also convert the only user.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Yep, I went looking for one of these, and I wasn't able to find it
easily. That's worse than a line which is 82-chars long, IMHO.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On Bay Trail and Cherry Trail devices we set the pm_disabled flag for I2C
busses which the OS shares with the PUNIT as these need special handling.
Until now we called dev_pm_syscore_device(dev, true) for I2C controllers
with this flag set to keep these I2C controllers always on.
After commit 12864ff854 ("ACPI / LPSS: Avoid PM quirks on suspend and
resume from hibernation"), this no longer works. This commit modifies
lpss_iosf_exit_d3_state() to only run if lpss_iosf_enter_d3_state() has ran
before it, so that it does not run on a resume from hibernate (or from S3).
On these systems the conditions for lpss_iosf_enter_d3_state() to run
never become true, so lpss_iosf_exit_d3_state() never gets called and
the 2 LPSS DMA controllers never get forced into D0 mode, instead they
are left in their default automatic power-on when needed mode.
The not forcing of D0 mode for the DMA controllers enables these systems
to properly enter S0ix modes, which is a good thing.
But after entering S0ix modes the I2C controller connected to the PMIC
no longer works, leading to e.g. broken battery monitoring.
The _PS3 method for this I2C controller looks like this:
Method (_PS3, 0, NotSerialized) // _PS3: Power State 3
{
If ((((PMID == 0x04) || (PMID == 0x05)) || (PMID == 0x06)))
{
Return (Zero)
}
PSAT |= 0x03
Local0 = PSAT /* \_SB_.I2C5.PSAT */
}
Where PMID = 0x05, so we enter the Return (Zero) path on these systems.
So even if we were to not call dev_pm_syscore_device(dev, true) the
I2C controller will be left in D0 rather then be switched to D3.
Yet on other Bay and Cherry Trail devices S0ix is not entered unless *all*
I2C controllers are in D3 mode. This combined with the I2C controller no
longer working now that we reach S0ix states on these systems leads to me
believing that the PUNIT itself puts the I2C controller in D3 when all
other conditions for entering S0ix states are true.
Since now the I2C controller is put in D3 over a suspend/resume we must
re-initialize it afterwards and that does indeed fix it no longer working.
This commit implements this fix by:
1) Making the suspend_late callback a no-op if pm_disabled is set and
making the resume_early callback skip the clock re-enable (since it now was
not disabled) while still doing the necessary I2C controller re-init.
2) Removing the dev_pm_syscore_device(dev, true) call, so that the suspend
and resume callbacks are actually called. Normally this would cause the
ACPI pm code to call _PS3 putting the I2C controller in D3, wreaking havoc
since it is shared with the PUNIT, but in this special case the _PS3 method
is a no-op so we can safely allow a "fake" suspend / resume.
Fixes: 12864ff854 ("ACPI / LPSS: Avoid PM quirks on suspend and resume ...")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200861
Cc: 4.15+ <stable@vger.kernel.org> # 4.15+
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 7ae81952cda ("i2c: i801: Allow ACPI SystemIO OpRegion to conflict
with PCI BAR") made it possible for AML code to access SMBus I/O ports
by installing custom SystemIO OpRegion handler and blocking i80i driver
access upon first AML read/write to this OpRegion.
However, while ThinkPad T560 does have SystemIO OpRegion declared under
the SMBus device, it does not access any of the SMBus registers:
Device (SMBU)
{
...
OperationRegion (SMBP, PCI_Config, 0x50, 0x04)
Field (SMBP, DWordAcc, NoLock, Preserve)
{
, 5,
TCOB, 11,
Offset (0x04)
}
Name (TCBV, 0x00)
Method (TCBS, 0, NotSerialized)
{
If ((TCBV == 0x00))
{
TCBV = (\_SB.PCI0.SMBU.TCOB << 0x05)
}
Return (TCBV) /* \_SB_.PCI0.SMBU.TCBV */
}
OperationRegion (TCBA, SystemIO, TCBS (), 0x10)
Field (TCBA, ByteAcc, NoLock, Preserve)
{
Offset (0x04),
, 9,
CPSC, 1
}
}
Problem with the current approach is that it blocks all I/O port access
and because this system has touchpad connected to the SMBus controller
after first AML access (happens during suspend/resume cycle) the
touchpad fails to work anymore.
Fix this so that we allow ACPI AML I/O port access if it does not touch
the region reserved for the SMBus.
Fixes: 7ae81952cda ("i2c: i801: Allow ACPI SystemIO OpRegion to conflict with PCI BAR")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200737
Reported-by: Yussuf Khalil <dev@pp3345.net>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This can be dropped with commit 771c035372
("deprecate the '__deprecated' attribute warnings entirely and for good")
now in upstream.
And we got rid of the last __deprecated use, too.
Signed-off-by: Sedat Dilek <sedat.dilek@credativ.de>
[wsa: shortened commit message to reflect the current situation]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The old @sunsite.dk address is no longer active, so update the references.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There aren't any users left. Remove this callback from the 2.4 times.
Phew, finally, that took years to reach...
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
- the core has now a lockless variant of i2c_smbus_xfer. Some open
coded versions of this got removed in drivers. This also enables
proper SCCB support in regmap.
- locking got a more precise naming. i2c_{un}lock_adapter() had to go,
and we know use i2c_lock_bus() consistently with flags like
I2C_LOCK_ROOT_ADAPTER and I2C_LOCK_SEGMENT to avoid ambiguity.
- the gpio fault injector got a new delicate testcase
- the bus recovery procedure got fixed to handle the new testcase
correctly
- a new quirk flag for controllers not able to handle zero length
messages together with driver updates to use it
- new drivers: FSI bus attached I2C masters, GENI I2C controller, Owl
family S900
- and a good set of driver improvements and bugfixes
* 'i2c/for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (77 commits)
i2c: rcar: implement STOP and REP_START according to docs
i2c: rcar: refactor private flags
i2c: core: ACPI: Make acpi_gsb_i2c_read_bytes() check i2c_transfer return value
i2c: core: ACPI: Properly set status byte to 0 for multi-byte writes
dt-bindings: i2c: rcar: Add r8a774a1 support
dt-bindings: i2c: sh_mobile: Add r8a774a1 support
i2c: imx: Simplify stopped state tracking
i2c: imx: Fix race condition in dma read
i2c: pasemi: remove hardcoded bus numbers on smbus
i2c: designware: Add SPDX license tag
i2c: designware: Convert to use struct i2c_timings
i2c: core: Parse SDA hold time from firmware
i2c: designware-pcidrv: Mark expected switch fall-through
i2c: amd8111: Mark expected switch fall-through
i2c: sh_mobile: use core to detect 'no zero length read' quirk
i2c: xlr: use core to detect 'no zero length' quirk
i2c: rcar: use core to detect 'no zero length' quirk
i2c: stu300: use core to detect 'no zero length' quirk
i2c: pmcmsp: use core to detect 'no zero length' quirk
i2c: mxs: use core to detect 'no zero length' quirk
...
When doing a REP_START after a read message, the driver used to trigger
a STOP first which would then be overwritten by REP_START. This was the
only stable method found when doing the last refactoring. However, this
was not in accordance with the documentation.
After research from our BSP team and myself, we now can implement a
version which works and is according to the documentation. The new
approach ensures the ICMCR register is only changed when really needed.
Tested on a R-Car Gen2 (H2) and Gen3 with DMA (M3N).
Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently acpi_gsb_i2c_read_bytes() directly returns i2c_transfer's return
value. i2c_transfer returns a value < 0 on error and 2 (for 2 successfully
executed transfers) on success. But the ACPI code expects 0 on success, so
currently acpi_gsb_i2c_read_bytes()'s caller does:
if (status > 0)
status = 0;
This commit makes acpi_gsb_i2c_read_bytes() return a value which can be
directly consumed by the ACPI code, mirroring acpi_gsb_i2c_write_bytes(),
this commit also makes acpi_gsb_i2c_read_bytes() explitcly check that
i2c_transfer returns 2, rather then accepting any value > 0.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
acpi_gsb_i2c_write_bytes() returns i2c_transfer()'s return value, which
is the number of transfers executed on success, so 1.
The ACPI code expects us to store 0 in gsb->status for success, not 1.
Specifically this breaks the following code in the Thinkpad 8 DSDT:
ECWR = I2CW = ECWR /* \_SB_.I2C1.BAT0.ECWR */
If ((ECST == Zero))
{
ECRD = I2CR /* \_SB_.I2C1.I2CR */
}
Before this commit we set ECST to 1, causing the read to never happen
breaking battery monitoring on the Thinkpad 8.
This commit makes acpi_gsb_i2c_write_bytes() return 0 when i2c_transfer()
returns 1, so the single write transfer completed successfully, and
makes it return -EIO on for other (unexpected) return values >= 0.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Always update the stopped state when busy status have been checked.
This is identical to what was done before, with the exception of error
handling.
Without this change, some errors cause the stopped state to be left in
incorrect state in i2c_imx_stop(), i2c_imx_dma_read(), i2c_imx_read() and
i2c_imx_xfer().
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This fixes a race condition, where the DMAEN bit ends up being set after
I2C slave has transmitted a byte following the dummy read. When that
happens, an interrupt is generated instead, and no DMA request is generated
to kickstart the DMA read, and a timeout happens after DMA_TIMEOUT (1 sec).
Fixed by setting the DMAEN bit before the dummy read.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
The pasemi smbus controller uses PCI_FUNC(dev->devfn) to define which
number bus to attach to, however this fails when something else is
probed first, for example an ATI Radeon graphics card will claim 9 or
10 busses, including the ones the pasemi wants.
Patch the driver to call i2c_add_adapter rather than
i2c_add_numbered_adapter.
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Replace short statement in comment with proper SPDX license tag.
Note, for i2c-desingware-slave.c the identifier is chosen
in accordance with MODULE_LICENSE() macro since it is visible to user.
Another point to this choice is that the header seems to be copy'n'paste
from the other file of this very driver.
Acked-by: Luis Oliveira <Luis.Oliveira@synopsys.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull regmap updates from Mark Brown:
"Several small new features for regmap this time around:
- Support for SCCB, an I2C variant used on some media cards. This has
also pulled in an I2C commit from Peter Rosin as a dependency.
- Addition of an API for reading repeatedly from registers where the
address doesn't automatically increment like some ADC outputs or
GPIO status registers.
- Support for bulk I/O on Slimbus"
* tag 'regmap-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Add regmap_noinc_read API
regmap: sccb: fix typo and sort headers alphabetically
i2c: smbus: add unlocked __i2c_smbus_xfer variant
regmap: add SCCB support
regmap: slimbus: add support to multi read/write
