commit d5d27fd982 upstream.
Disable BCH soft reset according to MX23 erratum #2847 ("BCH soft
reset may cause bus master lock up") for MX28 too. It has the same
problem.
Observed problem: once per 100,000+ MX28 reboots NAND read failed on
DMA timeout errors:
[ 1.770823] UBI: attaching mtd3 to ubi0
[ 2.768088] gpmi_nand: DMA timeout, last DMA :1
[ 3.958087] gpmi_nand: BCH timeout, last DMA :1
[ 4.156033] gpmi_nand: Error in ECC-based read: -110
[ 4.161136] UBI warning: ubi_io_read: error -110 while reading 64
bytes from PEB 0:0, read only 0 bytes, retry
[ 4.171283] step 1 error
[ 4.173846] gpmi_nand: Chip: 0, Error -1
Without BCH soft reset we successfully executed 1,000,000 MX28 reboots.
I have a quote from NXP regarding this problem, from July 18th 2016:
"As the i.MX23 and i.MX28 are of the same generation, they share many
characteristics. Unfortunately, also the erratas may be shared.
In case of the documented erratas and the workarounds, you can also
apply the workaround solution of one device on the other one. This have
been reported, but I’m afraid that there are not an estimated date for
updating the Errata documents.
Please accept our apologies for any inconveniences this may cause."
Fixes: 6f2a6a5256 ("mtd: nand: gpmi: reset BCH earlier, too, to avoid NAND startup problems")
Cc: stable@vger.kernel.org
Signed-off-by: Manfred Schlaegl <manfred.schlaegl@ginzinger.com>
Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c3c7dbf488 upstream.
The manufacturer specific initialization has already been done when
block unlocking takes place, and if anything goes wrong during this
procedure we should call spinand_manufacturer_cleanup().
Fixes: 7529df4652 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13c15e07ee upstream.
Looks like PROGRAM LOAD (AKA write cache) does not necessarily reset
the cache content to 0xFF (depends on vendor implementation), so we
must fill the page cache entirely even if we only want to program the
data portion of the page, otherwise we might corrupt the BBM or user
data previously programmed in OOB area.
Fixes: 7529df4652 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Reported-by: Stefan Roese <sr@denx.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81d9bdf590 upstream.
This patch fixes a memory corruption that occurred in the
qcom-nandc driver since it was converted to nand_scan().
On boot, an affected device will panic from a NPE at a weird place:
| Unable to handle kernel NULL pointer dereference at virtual address 0
| pgd = (ptrval)
| [00000000] *pgd=00000000
| Internal error: Oops: 80000005 [#1] SMP ARM
| CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.19.9 #0
| Hardware name: Generic DT based system
| PC is at (null)
| LR is at nand_block_isbad+0x90/0xa4
| pc : [<00000000>] lr : [<c0592240>] psr: 80000013
| sp : cf839d40 ip : 00000000 fp : cfae9e20
| r10: cf815810 r9 : 00000000 r8 : 00000000
| r7 : 00000000 r6 : 00000000 r5 : 00000001 r4 : cf815810
| r3 : 00000000 r2 : cfae9810 r1 : ffffffff r0 : cf815810
| Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
| Control: 10c5387d Table: 8020406a DAC: 00000051
| Process swapper/0 (pid: 1, stack limit = 0x(ptrval))
| [<c0592240>] (nand_block_isbad) from [<c0580a94>]
| [<c0580a94>] (allocate_partition) from [<c05811e4>]
| [<c05811e4>] (add_mtd_partitions) from [<c0581164>]
| [<c0581164>] (parse_mtd_partitions) from [<c057def4>]
| [<c057def4>] (mtd_device_parse_register) from [<c059d274>]
| [<c059d274>] (qcom_nandc_probe) from [<c0567f00>]
The problem is that the nand_scan()'s qcom_nand_attach_chip callback
is updating the nandc->max_cwperpage from 1 to 4. This causes the
sg_init_table of clear_bam_transaction() in the driver's
qcom_nandc_block_bad() to memset much more than what was initially
allocated by alloc_bam_transaction().
This patch restores the old behavior by reallocating the shared bam
transaction alloc_bam_transaction() after the chip was identified,
but before mtd_device_parse_register() (which is an alias for
mtd_device_register() - see panic) gets called. This fixes the
corruption and the driver is working again.
Cc: stable@vger.kernel.org
Fixes: 6a3cec64f1 ("mtd: rawnand: qcom: convert driver to nand_scan()")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cafb56dd74 upstream.
marvell_nfc_wait_op() waits for completion during 'timeout_ms'
milliseconds before throwing an error. While the logic is fine, the
value of 'timeout_ms' is given by the core and actually correspond to
the maximum time the NAND chip will take to complete the
operation. Assuming there is no overhead in the propagation of the
interrupt signal to the the NAND controller (through the Ready/Busy
line), this delay does not take into account the latency of the
operating system. For instance, for a page write, the delay given by
the core is rounded up to 1ms. Hence, when the machine is over loaded,
there is chances that this timeout will be reached.
There are two ways to solve this issue that are not incompatible:
1/ Enlarge the timeout value (if so, how much?).
2/ Check after the waiting method if we did not miss any interrupt
because of the OS latency (an interrupt is still pending). In this
case, we assume the operation exited successfully.
We choose the second approach that is a must in all cases, with the
possibility to also modify the timeout value to be, e.g. at least 1
second in all cases.
Fixes: 02f26ecf8c ("mtd: nand: add reworked Marvell NAND controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 33bf5519ae ]
PAGE_READ is used by RISC-V arch code included through mm headers,
and it makes sense to bring in a prefix on these in the driver.
drivers/mtd/nand/raw/qcom_nandc.c:153: warning: "PAGE_READ" redefined
#define PAGE_READ 0x2
In file included from include/linux/memremap.h:7,
from include/linux/mm.h:27,
from include/linux/scatterlist.h:8,
from include/linux/dma-mapping.h:11,
from drivers/mtd/nand/raw/qcom_nandc.c:17:
arch/riscv/include/asm/pgtable.h:48: note: this is the location of the previous definition
Caught by riscv allmodconfig.
Signed-off-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5d1e9c2212 upstream.
Use the new of_get_compatible_child() helper to lookup the nfc child
node instead of using of_find_compatible_node(), which searches the
entire tree from a given start node and thus can return an unrelated
(i.e. non-child) node.
This also addresses a potential use-after-free (e.g. after probe
deferral) as the tree-wide helper drops a reference to its first
argument (i.e. the node of the device being probed).
While at it, also fix a related nfc-node reference leak.
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Cc: stable <stable@vger.kernel.org> # 4.11
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Josh Wu <rainyfeeling@outlook.com>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fbed20280d ]
There is a potential execution path in which function
of_find_compatible_node() returns NULL. In such a case,
we end up having a NULL pointer dereference when accessing
pointer *nfc_np* in function of_clk_get().
So, we better don't take any chances and fix this by null
checking pointer *nfc_np* before calling of_clk_get().
Addresses-Coverity-ID: 1473052 ("Dereference null return value")
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0d55c668b2 ]
NAND devices need additional data area (OOB) for error correction,
but it is also used for Bad Block Marker (BBM). In many cases, the
first byte in OOB is used for BBM, but the location actually depends
on chip vendors. The NAND controller should preserve the precious
BBM to keep track of bad blocks.
In Denali IP, the SPARE_AREA_SKIP_BYTES register is used to specify
the number of bytes to skip from the start of OOB. The ECC engine
will automatically skip the specified number of bytes when it gets
access to OOB area.
The same value for SPARE_AREA_SKIP_BYTES should be used between
firmware and the operating system if you intend to use the NAND
device across the control hand-off.
In fact, the current denali.c code expects firmware to have already
set the SPARE_AREA_SKIP_BYTES register, then reads the value out.
If no firmware (or bootloader) has initialized the controller, the
register value is zero, which is the default after power-on-reset.
In other words, the Linux driver cannot initialize the controller
by itself.
Some possible solutions are:
[1] Add a DT property to specify the skipped bytes in OOB
[2] Associate the preferred value with compatible
[3] Hard-code the default value in the driver
My first attempt was [1], but in the review process, [3] was suggested
as a counter-implementation.
(https://lore.kernel.org/patchwork/patch/983055/)
The default value 8 was chosen to match to the boot ROM of the UniPhier
platform. The preferred value may vary by platform. If so, please
trade up to a different solution.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 53c83b5975 upstream.
With the current implementation, the complete() in the IRQ handler is
supposed to be called only if the register status has one or the other
RDY bit set. Other events might trigger an interrupt as well if
enabled, but should not end-up with a complete() call.
For this purpose, the code was checking if the other bits were set, in
this case complete() was not called. This is wrong as two events might
happen in a very tight time-frame and if the NDSR status read reports
two bits set (eg. RDY(0) and RDDREQ) at the same time, complete() was
not called.
This logic would lead to timeouts in marvell_nfc_wait_op() and has
been observed on PXA boards (NFCv1) in the Hamming write path.
Fixes: 02f26ecf8c ("mtd: nand: add reworked Marvell NAND controller driver")
Cc: stable@vger.kernel.org
Reported-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I thought the read-back of the DMA_ENABLE register was unnecessary
(at least it is working on my boards), then deleted it in commit
586a2c5290 ("mtd: nand: denali: squash denali_enable_dma() helper
into caller"). Sorry, I was wrong - it caused a timing issue on
Cyclone5 SoCFPGAs.
Revive the register read-back, commenting why this is necessary.
Fixes: 586a2c5290 ("mtd: nand: denali: squash denali_enable_dma() helper into caller")
Cc: <stable@vger.kernel.org>
Reported-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Since the addition of WARN_ON() in nand_subop_get_data/addr_len()
helpers, this driver will produce harmless warnings (mostly at probe)
just because it always calls the nand_subop_get_data_len() helper in
the parsing function (even on non-data instructions, where this value
is meaningless and unneeded).
Fix these warnings by deriving the length only when it is relevant.
Fixes: 760c435e0f ("mtd: rawnand: make subop helpers return unsigned values")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Commit 49aa76b166 ("mtd: rawnand: do not execute nand_scan_ident()
if maxchips is zero") gave a new meaning for calling nand_scan_ident()
with maxchips=0.
It is a special usage for some drivers such as docg4, but actually
the Denali driver may pass maxchips=0 to nand_scan() when the driver
is enabled but no NAND chip is found on the board for some reasons.
If nand_scan_with_ids() is called with maxchips=0, nand_scan_ident()
is skipped, then nand_set_defaults() is skipped as well. Thus, the
driver must set chip->controller beforehand. Otherwise, nand_attach()
causes NULL pointer dereference.
In fact, the Denali controller knows the number of connected chips
before calling nand_scan_ident(); if DEVICE_RESET fails, there is no
chip in that chip select. Then, denali_reset_banks() sets the maxchips
to the number of detected chips. If no chip is found, maxchips is zero.
In this case, there is no point for calling nand_scan() because we know
it will fail for sure. Let's make the probe function fail immediately.
Fixes: 49aa76b166 ("mtd: rawnand: do not execute nand_scan_ident() if maxchips is zero")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
If gcc (e.g. 4.1.2) decides not to inline init_mtd_structs() and
read_id_reg(), this will cause section mismatches, and crashes:
WARNING: drivers/mtd/nand/raw/docg4.o(.text+0xc10): Section mismatch in reference from the function docg4_attach_chip() to the function .init.text:init_mtd_structs()
The function docg4_attach_chip() references
the function __init init_mtd_structs().
This is often because docg4_attach_chip lacks a __init
annotation or the annotation of init_mtd_structs is wrong.
WARNING: drivers/mtd/nand/raw/docg4.o(.text+0xc3e): Section mismatch in reference from the function docg4_attach_chip() to the function .init.text:read_id_reg()
The function docg4_attach_chip() references
the function __init read_id_reg().
This is often because docg4_attach_chip lacks a __init
annotation or the annotation of read_id_reg is wrong.
Fix this by dropping the now incorrect __init annotations from
init_mtd_structs() and read_id_reg().
Fixes: 66a38478dc ("mtd: rawnand: docg4: convert driver to nand_scan()")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
Pull sound updates from Takashi Iwai:
"It's been busy summer weeks and hence lots of changes, partly for a
few new drivers and partly for a wide range of fixes.
Here are highlights:
ALSA Core:
- Fix rawmidi buffer management, code cleanup / refactoring
- Fix the SG-buffer page handling with incorrect fallback size
- Fix the stall at virmidi trigger callback with a large buffer; also
offloading and code-refactoring along with it
- Various ALSA sequencer code cleanups
ASoC:
- Deploy the standard snd_pcm_stop_xrun() helper in several drivers
- Support for providing name prefixes to generic component nodes
- Quite a few fixes for DPCM as it gains a bit wider use and more
robust testing
- Generalization of the DIO2125 support to a simple amplifier driver
- Accessory detection support for the audio graph card
- DT support for PXA AC'97 devices
- Quirks for a number of new x86 systems
- Support for AM Logic Meson, Everest ES7154, Intel systems with
RT5682, Qualcomm QDSP6 and WCD9335, Realtek RT5682 and TI TAS5707
HD-audio:
- Code refactoring in HD-audio ext codec codes to drop own classes;
preliminary works for the upcoming legacy codec support
- Generalized DRM audio component for the upcoming radeon / amdgpu
support
- Unification of mic mute-LED and GPIO support for various codecs
- Further improvement of CA0132 codec support including Recon3D
- Proper vga_switcheroo handling for AMD i-GPU
- Update of model list in documentation
- Fixups for another HP Spectre x360, Conexant codecs, power-save
blacklist update
USB-audio:
- Fix the invalid sample rate setup with external clock
- Support of UAC3 selector units and processing units
- Basic UAC3 power-domain support
- Support for Encore mDSD and Thesycon-based DSD devices
- Preparation for future complete callback changes
Firewire:
- Add support for MOTU Traveler
Misc:
- The endianess notation fixes in various drivers
- Add fall-through comment in lots of drivers
- Various sparse warning fixes, e.g. about PCM format types"
* tag 'sound-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (529 commits)
ASoC: adav80x: mark expected switch fall-through
ASoC: da7219: Add delays to capture path to remove DC offset noise
ALSA: usb-audio: Mark expected switch fall-through
ALSA: mixart: Mark expected switch fall-through
ALSA: opl3: Mark expected switch fall-through
ALSA: hda/ca0132 - Add exit commands for Recon3D
ALSA: hda/ca0132 - Change mixer controls for Recon3D
ALSA: hda/ca0132 - Add Recon3D input and output select commands
ALSA: hda/ca0132 - Add DSP setup defaults for Recon3D
ALSA: hda/ca0132 - Add Recon3D startup functions and setup
ALSA: hda/ca0132 - Add bool variable to enable/disable pci region2 mmio
ALSA: hda/ca0132 - Add Recon3D pincfg
ALSA: hda/ca0132 - Add quirk ID and enum for Recon3D
ALSA: hda/ca0132 - Add alt_functions unsolicited response
ALSA: hda/ca0132 - Clean up ca0132_init function.
ALSA: hda/ca0132 - Create mmio gpio function to make code clearer
ASoC: wm_adsp: Make DSP name configurable by codec driver
ASoC: wm_adsp: Declare firmware controls from codec driver
ASoC: max98373: Added software reset register to readable registers
ASoC: wm_adsp: Correct DSP pointer for preloader control
...
The driver uses genalloc functions. Select GENERIC_ALLOCATOR to prevent
build errors when selected through COMPILE_TEST.
Fixes: 88a40e7dca ("mtd: rawnand: atmel: Allow selection of this driver when COMPILE_TEST=y")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Now that it is possible to do dynamic allocations during the
identification phase, convert the onfi_params structure (which is only
needed with ONFI compliant chips) into a pointer that will be allocated
only if needed.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Thanks to the migration of all drivers to use nand_scan() and the
related nand_controller_ops, we can now allocate data during the
detection phase. Let's do it first for the NAND model parameter which
is allocated in nand_detect().
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Both nand_scan_ident() and nand_scan_tail() helpers used to be called
directly from controller drivers that needed to tweak some ECC-related
parameters before nand_scan_tail(). This separation prevented dynamic
allocations during the phase of NAND identification, which was
inconvenient.
All controller drivers have been moved to use nand_scan(), in
conjunction with the chip->ecc.[attach|detach]_chip() hooks that
actually do the required tweaking sequence between both ident/tail
calls, allowing programmers to use dynamic allocation as they need all
across the scanning sequence.
Declare nand_scan_[ident|tail]() statically now.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
A comment in the probe declares that values are assigned to ecc.size
and ecc.bytes, but these values will be overwritten. This is not
entirely right as they are overwritten only if
mtd->writesize >= 512. Let's clarify this by moving these assignations
to txx9ndfmc_nand_scan().
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Prepare the migration to nand_scan() by moving both calls to
nand_scan_ident() and nand_scan_tail() in a single spot.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
An error after nand_scan_tail() should trigger a nand_cleanup(), not a
nand_release() as mtd_device_register() (or one of its variants) has not
been called and there is no need to deregister any MTD device yet.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Some driver (eg. docg4) will need to handle themselves the
identification phase. As part of the migration to use nand_scan()
everywhere (which will unconditionnaly call nand_scan_ident()), we add
a condition at the start of nand_scan_with_ids() to jump over
nand_scan_ident() if the maxchips parameters is zero, meaning that the
driver does not want the core to handle this phase.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
No need for an atmel_nand_register() function, let's move the code in
it directly where the function was called: in
atmel_nand_controller_add_nand(). To make things consistent, also
rename atmel_nand_unregister() into
atmel_nand_controller_remove_nand().
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan_with_ids() (alternative to nand_scan() for passing
a flash IDs table) instead of the nand_scan_ident() + nand_scan_tail()
pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
nand_cleanup() should be called upon error after a successful
nand_scan_tail().
Rework the error path to follow this rule .
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
As already done in the core, calling a struct nand_controller
'hw_control' is misleading. Use the same name as in nand_base.c:
'controller'.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
