The bInterval is set to 4 (i.e. 8 microframes => 1ms) and the only bit
that the driver pays attention to is "link was reset". If there's a
flapping status bit in that endpoint data, (such as if PHY negotiation
needs a few tries to get a stable link) then polling at a slower rate
would act as a de-bounce.
See: https://github.com/raspberrypi/linux/issues/2447
Enable EEE mode as soon as possible after connecting to the PHY, and
before phy_start. This avoids a second link negotiation, which speeds
up booting and stops the interface failing to become ready.
See: https://github.com/raspberrypi/linux/issues/2437
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add two new DT properties:
* microchip,eee-enabled - a boolean to enable EEE
* microchip,tx-lpi-timer - time in microseconds to wait before entering
low power state
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
For applications of the LAN78xx that don't have valid programmed
EEPROMs or OTPs, enabling both LEDs and auto-negotiation by default
seems reasonable.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
smsc95xx is adjusting truesize when it shouldn't, and following a recent patch from Eric this is now triggering warnings.
This patch stops smsc95xx from changing truesize.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
[ Upstream commit 97dc47a130 ]
The 1199:68C0 USB ID is reused by Sierra WP7607 which requires the DTR
quirk to be detected. Apply QMI_QUIRK_SET_DTR unconditionally as
already done for other IDs shared between different devices.
Signed-off-by: Beniamino Galvani <bgalvani@redhat.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 822e44b45e ]
Quectel EG12 (module)/EM12 (M.2 card) is a Cat. 12 LTE modem. The modem
behaves in the same way as the EP06, so the "set DTR"-quirk must be
applied and the diagnostic-interface check performed. Since the
diagnostic-check now applies to more modems, I have renamed the function
from quectel_ep06_diag_detected() to quectel_diag_detected().
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6eea3527e6 ]
The ax88772_bind() should return error code immediately when the PHY
was not reset properly through ax88772a_hw_reset().
Otherwise, The asix_get_phyid() will block when get the PHY
Identifier from the PHYSID1 MII registers through asix_mdio_read()
due to the PHY isn't ready. Furthermore, it will produce a lot of
error message cause system crash.As follows:
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to write
reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to send
software reset: ffffffb9
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to write
reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to enable
software MII access
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to read
reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to write
reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to enable
software MII access
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to read
reg index 0x0000: -71
...
Signed-off-by: Zhang Run <zhang.run@zte.com.cn>
Reviewed-by: Yang Wei <yang.wei9@zte.com.cn>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 810eeb1f41 ]
The smsc95xx driver already takes into account the NET_IP_ALIGN
parameter when setting up the receive packet data, which means
we do not need to worry about aligning the packets in the usbnet
driver.
Adding the EVENT_NO_IP_ALIGN means that the IPv4 header is now
passed to the ip_rcv() routine with the start on an aligned address.
Tested on Raspberry Pi B3.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f87118d576 ]
This patch adds MTU default value to qmap network interface in
order to avoid "RTNETLINK answers: No buffer space available"
error when setting an ipv6 address.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d667044f49 ]
This patch fixes qmap header retrieval when modem is configured for
dl data aggregation.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15515aaaa6 ]
Current state for the lan78xx driver does not allow for changing the
MAC address of the interface, without either removing the module (if
you compiled it that way) or rebooting the machine. If you attempt to
change the MAC address, ifconfig will show the new address, however,
the system/interface will not respond to any traffic using that
configuration. A few short-term options to work around this are to
unload the module and reload it with the new MAC address, change the
interface to "promisc", or reboot with the correct configuration to
change the MAC.
This patch enables the ability to change the MAC address via fairly normal means...
ifdown <interface>
modify entry in /etc/network/interfaces OR a similar method
ifup <interface>
Then test via any network communication, such as ICMP requests to gateway.
My only test platform for this patch has been a raspberry pi model 3b+.
Signed-off-by: Jason Martinsen <jasonmartinsen@msn.com>
-----
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c3db4105c ]
Added support for Fibocom NL678 series cellular module QMI interface.
Using QMI_QUIRK_SET_DTR required for Qualcomm MDM9x40 series chipsets.
Signed-off-by: Jörgen Storvist <jorgen.storvist@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1986af16e8 ]
Added support for the Telit LN940 series cellular modules QMI interface.
QMI_QUIRK_SET_DTR quirk requied for Qualcomm MDM9x40 chipset.
Signed-off-by: Jörgen Storvist <jorgen.storvist@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 110a1cc28b ]
Added support for Fibocom NL668 series QMI interface.
Using QMI_QUIRK_SET_DTR required for Qualcomm MDM9x07 chipsets.
Signed-off-by: Jörgen Storvist <jorgen.storvist@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5146f95df7 upstream.
The function hso_probe reads if_num from the USB device (as an u8) and uses
it without a length check to index an array, resulting in an OOB memory read
in hso_probe or hso_get_config_data.
Add a length check for both locations and updated hso_probe to bail on
error.
This issue has been assigned CVE-2018-19985.
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: Hui Peng <benquike@gmail.com>
Signed-off-by: Mathias Payer <mathias.payer@nebelwelt.net>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7b900ead6c ]
We need to make sure, that the carrier check polling is disabled
while suspending. Otherwise we can end up with usbnet_read_cmd()
being issued when only usbnet_read_cmd_nopm() is allowed. If this
happens, read operations lock up.
Fixes: d69d169493 ("usbnet: smsc95xx: fix link detection for disabled autonegotiation")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Raghuram Chary J <RaghuramChary.Jallipalli@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 85b18b0237 ]
The commit f77f0aee4d ("net: use core MTU range checking in USB NIC
drivers") introduce a common MTU handling for usbnet. But it's missing
the necessary changes for smsc95xx. So set the MTU range accordingly.
This patch has been tested on a Raspberry Pi 3.
Fixes: f77f0aee4d ("net: use core MTU range checking in USB NIC drivers")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added support for Gemalto's Cinterion ALASxx WWAN interfaces
by adding QMI_FIXED_INTF with Cinterion's VID and PID.
Signed-off-by: Giacinto Cifelli <gciofono@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cancel pending work before freeing smsc75xx private data structure
during binding. This fixes the following crash in the driver:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000050
IP: mutex_lock+0x2b/0x3f
<snipped>
Workqueue: events smsc75xx_deferred_multicast_write [smsc75xx]
task: ffff8caa83e85700 task.stack: ffff948b80518000
RIP: 0010:mutex_lock+0x2b/0x3f
<snipped>
Call Trace:
smsc75xx_deferred_multicast_write+0x40/0x1af [smsc75xx]
process_one_work+0x18d/0x2fc
worker_thread+0x1a2/0x269
? pr_cont_work+0x58/0x58
kthread+0xfa/0x10a
? pr_cont_work+0x58/0x58
? rcu_read_unlock_sched_notrace+0x48/0x48
ret_from_fork+0x22/0x40
Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver does not check for Wake-on-LAN modes specified by an user,
but will conditionally set the device as wake-up enabled or not based on
that, which could be a very confusing user experience.
Fixes: e0e474a83c ("smsc95xx: add wol magic packet support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver does not check for Wake-on-LAN modes specified by an user,
but will conditionally set the device as wake-up enabled or not based on
that, which could be a very confusing user experience.
Fixes: 6c63650326 ("smsc75xx: add wol magic packet support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver does not check for Wake-on-LAN modes specified by an user,
but will conditionally set the device as wake-up enabled or not based on
that, which could be a very confusing user experience.
Fixes: 21ff2e8976 ("r8152: support WOL")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently silently accepts unsupported Wake-on-LAN modes
(other than WAKE_PHY or WAKE_MAGIC) without reporting that to the user,
which is confusing.
Fixes: 19a38d8e0a ("USB2NET : SR9800 : One chip USB2.0 USB2NET SR9800 Device Driver Support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver supports a fair amount of Wake-on-LAN modes, but is not
checking that the user specified one that is supported.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Woojung Huh <Woojung.Huh@Microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently silently accepts unsupported Wake-on-LAN modes
(other than WAKE_PHY or WAKE_MAGIC) without reporting that to the user,
which is confusing.
Fixes: e2ca90c276 ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently silently accepts unsupported Wake-on-LAN modes
(other than WAKE_PHY or WAKE_MAGIC) without reporting that to the user,
which is confusing.
Fixes: 2e55cc7210 ("[PATCH] USB: usbnet (3/9) module for ASIX Ethernet adapters")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent firmware revisions have added the ability to force
these modems to USB2 mode, hiding their SuperSpeed
capabilities from the host. The driver has been using the
SuperSpeed capability, as shown by the bcdUSB field of the
device descriptor, to detect the need to enable the DTR
quirk. This method fails when the modems are forced to
USB2 mode by the modem firmware.
Fix by unconditionally enabling the DTR quirk for the
affected device IDs.
Reported-by: Fred Veldini <fred.veldini@gmail.com>
Reported-by: Deshu Wen <dwen@sierrawireless.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Reported-by: Fred Veldini <fred.veldini@gmail.com>
Reported-by: Deshu Wen <dwen@sierrawireless.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quectel EP06 (and EM06/EG06) supports dynamic configuration of USB
interfaces, without the device changing VID/PID or configuration number.
When the configuration is updated and interfaces are added/removed, the
interface numbers change. This means that the current code for matching
EP06 does not work.
This patch removes the current EP06 interface number match, and replaces
it with a match on class, subclass and protocol. Unfortunately, matching
on those three alone is not enough, as the diag interface exports the
same values as QMI. The other serial interfaces + adb export different
values and do not match.
The diag interface only has two endpoints, while the QMI interface has
three. I have therefore added a check for number of interfaces, and we
ignore the interface if the number of endpoints equals two.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl8152_system_suspend defines the variable "ret", but it is not modified
after initialization. So just remove it.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use ARRAY_SIZE to replace open code sizeof(lan78xx_regs) / sizeof(u32).
It make the code concise.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BTF conflicts were simple overlapping changes.
The virtio_net conflict was an overlap of a fix of statistics counter,
happening alongisde a move over to a bonafide statistics structure
rather than counting value on the stack.
Signed-off-by: David S. Miller <davem@davemloft.net>
As long the bh tasklet isn't scheduled once, no packet from the rx path
will be handled. Since the tx path also schedule the same tasklet
this situation only persits until the first packet transmission.
So fix this issue by scheduling the tasklet after link reset.
Link: https://github.com/raspberrypi/linux/issues/2617
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet")
Suggested-by: Floris Bos <bos@je-eigen-domein.nl>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sr9700_bind() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
setup_pegasus_II() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mii_nway_restart is not pm aware which results in a rtnl deadlock.
Implement mii_nway_restart manual by setting BMCR_ANRESTART if
BMCR_ANENABLE is set.
To reproduce:
* plug an asix based usb network interface
* wait until the device enters PM (~5 sec)
* `ip link set eth1 up` will never return
Fixes: d9fe64e511 ("net: asix: Add in_pm parameter")
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver can spam the kernel log with multiple messages of:
net eth0: eth0: allmulti set
Usually 4 or 8 at a time (probably because of using ConnMan).
This message doesn't seem useful, so let's demote it from dev_info()
to dev_dbg().
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb size calculation in lan78xx_tx_bh is in race with the start_xmit,
which could lead to rare kernel oopses. So protect the whole skb walk with
a spin lock. As a benefit we can unlink the skb directly.
This patch was tested on Raspberry Pi 3B+
Link: https://github.com/raspberrypi/linux/issues/2608
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Floris Bos <bos@je-eigen-domein.nl>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the swap macro and remove unnecessary variable *temp*.
This makes the code easier to read and maintain. Also, slightly
refactor some code due to the removal of *temp*.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the USB id of LTE modem Quectel EG91. It requires the
same quirk as other Quectel modems to make it work.
Signed-off-by: Matevz Vucnik <vucnikm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
In certain conditions, the device may not be able to link in gigabit mode. This software workaround ensures that the device will not enter the failure state.
Fixes: d0cad87170 ("SMSC75XX USB 2.0 Gigabit Ethernet Devices")
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
