[ Upstream commit 2632f22ebd ]
When there are no SPQ entries left in the free_pool, new entries are
allocated and are added to the unlimited list. When an entry in the pool
is available, the content is copied from the original entry, and the new
entry is sent to the device. qed_spq_post() is not aware of that, so the
additional entry is stored in the original entry as p_post_ent, which can
later be returned to the pool.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba766b8b99 ]
Since commit bacd75cfac ("i40e/i40evf: Add capability exchange for
outer checksum", 2017-04-06) the i40e driver has not reported support
for IP-in-IP offloads. This likely occurred due to a bad rebase, as the
commit extracts hw_enc_features into its own variable. As part of this
change, it dropped the NETIF_F_FSO_IPXIP flags from the
netdev->hw_enc_features. This was unfortunately not caught during code
review.
Fix this by adding back the missing feature flags.
For reference, NETIF_F_GSO_IPXIP4 was added in commit 7e13318daa
("net: define gso types for IPx over IPv4 and IPv6", 2016-05-20),
replacing NETIF_F_GSO_IPIP and NETIF_F_GSO_SIT.
NETIF_F_GSO_IPXIP6 was added in commit bf2d1df395 ("intel: Add support
for IPv6 IP-in-IP offload", 2016-05-20).
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d944b46992 ]
Currently if the driver does a TSO offload the bytecount sent to
netdev_tx_sent_queue will be incorrect. This is because in ice_tso we
overwrite the initial value that we set in ice_tx_map. This creates a
mismatch between the Tx and Tx clean flow. In the Tx clean flow we
calculate the bytecount (called total_bytes) as we clean the
descriptors so the value used in the Tx clean path is correct. Fix this
by using += in ice_tso instead of =. This fixes the mismatch in
bytecount mentioned above.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8ccbb7d2f ]
The vport should be initialized to hdev->vport for each bp group,
otherwise it will cause out-of-bounds access and bp setting not
correct problem.
[ 35.254124] BUG: KASAN: slab-out-of-bounds in hclge_pause_setup_hw+0x2a0/0x3f8 [hclge]
[ 35.254126] Read of size 2 at addr ffff803b6651581a by task kworker/0:1/14
[ 35.254132] CPU: 0 PID: 14 Comm: kworker/0:1 Not tainted 4.19.0-rc7-hulk+ #85
[ 35.254133] Hardware name: Huawei D06/D06, BIOS Hisilicon D06 UEFI RC0 - B052 (V0.52) 09/14/2018
[ 35.254141] Workqueue: events work_for_cpu_fn
[ 35.254144] Call trace:
[ 35.254147] dump_backtrace+0x0/0x2f0
[ 35.254149] show_stack+0x24/0x30
[ 35.254154] dump_stack+0x110/0x184
[ 35.254157] print_address_description+0x168/0x2b0
[ 35.254160] kasan_report+0x184/0x310
[ 35.254162] __asan_load2+0x7c/0xa0
[ 35.254170] hclge_pause_setup_hw+0x2a0/0x3f8 [hclge]
[ 35.254177] hclge_tm_init_hw+0x794/0x9f0 [hclge]
[ 35.254184] hclge_tm_schd_init+0x48/0x58 [hclge]
[ 35.254191] hclge_init_ae_dev+0x778/0x1168 [hclge]
[ 35.254196] hnae3_register_ae_dev+0x14c/0x298 [hnae3]
[ 35.254206] hns3_probe+0x88/0xa8 [hns3]
[ 35.254210] local_pci_probe+0x7c/0xf0
[ 35.254212] work_for_cpu_fn+0x34/0x50
[ 35.254214] process_one_work+0x4d4/0xa38
[ 35.254216] worker_thread+0x55c/0x8d8
[ 35.254219] kthread+0x1b0/0x1b8
[ 35.254222] ret_from_fork+0x10/0x1c
[ 35.254224] The buggy address belongs to the page:
[ 35.254228] page:ffff7e00ed994400 count:1 mapcount:0 mapping:0000000000000000 index:0x0 compound_mapcount: 0
[ 35.273835] flags: 0xfffff8000008000(head)
[ 35.282007] raw: 0fffff8000008000 dead000000000100 dead000000000200 0000000000000000
[ 35.282010] raw: 0000000000000000 0000000000000000 00000001ffffffff 0000000000000000
[ 35.282012] page dumped because: kasan: bad access detected
[ 35.282014] Memory state around the buggy address:
[ 35.282017] ffff803b66515700: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282019] ffff803b66515780: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282021] >ffff803b66515800: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282022] ^
[ 35.282024] ffff803b66515880: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282026] ffff803b66515900: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282028] ==================================================================
[ 35.282029] Disabling lock debugging due to kernel taint
[ 35.282747] hclge driver initialization finished.
Fixes: 67bf2541f4 ("net: hns3: Fixes the back pressure setting when sriov is enabled")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6702185c1f ]
This change resolves a driver bug where the driver is logging a
message that says "Spoofed packets detected". This can occur on the PF
(host) when a VF has VLAN+MACVLAN enabled and is re-started with a
different MAC address.
MAC and VLAN anti-spoofing filters are to be enabled together.
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: Piotr Skajewski <piotrx.skajewski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2f74dbaf1 ]
The spin lock of the command queue only need to be initialized once
when the driver initializes the command queue. It is not necessary to
initialize the spin lock when resetting. At the same time, the
modification of the queue member should be performed after acquiring
the lock.
Fixes: 3efb960f05 ("net: hns3: Refactor the initialization of command queue")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c88ed1d79 ]
In a multi-core machine, the mailbox service and reset service
will be executed at the same time. The reset service will re-initialize
the command queue, before that, the mailbox handler can only get some
invalid messages.
The HCLGE_STATE_CMD_DISABLE flag means that the command queue is not
available and needs to be reinitialized. Therefore, when the mailbox
handler recognizes this flag, it should not process the command.
Fixes: dde1a86e93 ("net: hns3: Add mailbox support to PF driver")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a963052e53 ]
Since hclge_reset_wait() is used to wait for the hardware to complete
the reset, it is not necessary to hold the rtnl_lock during
hclge_reset_wait(). So this patch releases the lock for the duration
of hclge_reset_wait().
Fixes: 6d4fab3953 ("net: hns3: Reset net device with rtnl_lock")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 29118ab962 ]
Since hclgevf_reset_wait() is used to wait for the hardware to complete
the reset, it is not necessary to hold the rtnl_lock during
hclgevf_reset_wait(). So this patch releases the lock for the duration
of hclgevf_reset_wait().
Fixes: 6988eb2a9b ("net: hns3: Add support to reset the enet/ring mgmt layer")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b900ead6c ]
We need to make sure, that the carrier check polling is disabled
while suspending. Otherwise we can end up with usbnet_read_cmd()
being issued when only usbnet_read_cmd_nopm() is allowed. If this
happens, read operations lock up.
Fixes: d69d169493 ("usbnet: smsc95xx: fix link detection for disabled autonegotiation")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Raghuram Chary J <RaghuramChary.Jallipalli@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 85b18b0237 ]
The commit f77f0aee4d ("net: use core MTU range checking in USB NIC
drivers") introduce a common MTU handling for usbnet. But it's missing
the necessary changes for smsc95xx. So set the MTU range accordingly.
This patch has been tested on a Raspberry Pi 3.
Fixes: f77f0aee4d ("net: use core MTU range checking in USB NIC drivers")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 96801552f8 ]
The CPU policer used to police packets being trapped via a local route
(IP2ME) was incorrectly configured to police based on bytes per second
instead of packets per second.
Change the policer to police based on packets per second and avoid
packet loss under certain circumstances.
Fixes: 9148e7cf73 ("mlxsw: spectrum: Add policers for trap groups")
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit df5a8ec64e ]
Up until commit 7e5fbd1e07 ("net: mdio-gpio: Convert to use gpiod
functions where possible"), the _cansleep variants of the gpio_ API was
used. After that commit and the change to gpiod_ API, the _cansleep()
was dropped. This then results in WARN_ON() when used with GPIO
devices which do sleep. Add back the _cansleep() to avoid this.
Fixes: 7e5fbd1e07 ("net: mdio-gpio: Convert to use gpiod functions where possible")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d02854dc19 ]
A null dereference was observed when a sysctl was being set
from userspace and rmnet was stuck trying to complete some actions
in the NETDEV_REGISTER callback. This is because the real_dev is set
only after the device registration handler completes.
sysctl call stack -
<6> Unable to handle kernel NULL pointer dereference at
virtual address 00000108
<2> pc : rmnet_vnd_get_iflink+0x1c/0x28
<2> lr : dev_get_iflink+0x2c/0x40
<2> rmnet_vnd_get_iflink+0x1c/0x28
<2> inet6_fill_ifinfo+0x15c/0x234
<2> inet6_ifinfo_notify+0x68/0xd4
<2> ndisc_ifinfo_sysctl_change+0x1b8/0x234
<2> proc_sys_call_handler+0xac/0x100
<2> proc_sys_write+0x3c/0x4c
<2> __vfs_write+0x54/0x14c
<2> vfs_write+0xcc/0x188
<2> SyS_write+0x60/0xc0
<2> el0_svc_naked+0x34/0x38
device register call stack -
<2> notifier_call_chain+0x84/0xbc
<2> raw_notifier_call_chain+0x38/0x48
<2> call_netdevice_notifiers_info+0x40/0x70
<2> call_netdevice_notifiers+0x38/0x60
<2> register_netdevice+0x29c/0x3d8
<2> rmnet_vnd_newlink+0x68/0xe8
<2> rmnet_newlink+0xa0/0x160
<2> rtnl_newlink+0x57c/0x6c8
<2> rtnetlink_rcv_msg+0x1dc/0x328
<2> netlink_rcv_skb+0xac/0x118
<2> rtnetlink_rcv+0x24/0x30
<2> netlink_unicast+0x158/0x1f0
<2> netlink_sendmsg+0x32c/0x338
<2> sock_sendmsg+0x44/0x60
<2> SyS_sendto+0x150/0x1ac
<2> el0_svc_naked+0x34/0x38
Fixes: b752eff5be ("net: qualcomm: rmnet: Implement ndo_get_iflink")
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0432e83319 ]
Since 4.19 the following error in sysfs has appeared when using the
r8169 NIC driver:
$cd /sys/module/realtek/drivers
$ls -l
ls: cannot access 'mdio_bus:RTL8201F 10/100Mbps Ethernet': No such file or directory
[..garbled dir entries follow..]
Apparently the forward slash in "10/100Mbps Ethernet" is interpreted
as directory separator that leads nowhere, and was introduced in commit
513588dd44 ("net: phy: realtek: add RTL8201F phy-id and functions").
Fix this by removing the offending slash in the driver name.
Other drivers in net/phy seem to have the same problem, but I cannot
test/verify them.
Fixes: 513588dd44 ("net: phy: realtek: add RTL8201F phy-id and functions")
Signed-off-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a9049ff921 ]
The mv88e6161 would sometime fail to probe with a timeout waiting for
the switch to complete an operation. This operation is supposed to
clear the statistics counters. However, due to a read/modify/write,
without the needed mask, the operation actually carried out was more
random, with invalid parameters, resulting in the switch not
responding. We need to preserve the histogram mode bits, so apply a
mask to keep them.
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Fixes: 40cff8fca9 ("net: dsa: mv88e6xxx: Fix stats histogram mode")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit acf3766b36 ]
The mlx5e channels should be closed before mlx5i_uninit_underlay_qp
puts the QP into RST (reset) state during mlx5i_close. Currently QP
state incorrectly set to RST before channels got deactivated and closed,
since mlx5_post_send request expects QP in RTS (Ready To Send) state.
The fix is to keep QP in RTS state until mlx5e channels get closed
and to reset QP afterwards.
Also this fix is simply correct in order to keep the open/close flow
symmetric, i.e mlx5i_init_underlay_qp() is called first thing at open,
the correct thing to do is to call mlx5i_uninit_underlay_qp() last thing
at close, which is exactly what this patch is doing.
Fixes: dae37456c8 ("net/mlx5: Support for attaching multiple underlay QPs to root flow table")
Signed-off-by: Denis Drozdov <denisd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f2b18732ee ]
The commit "net/mlx5: Refactor accel IPSec code" introduced a
bug where asynchronous short time change in hash key value
by create/release SA context might happen during an asynchronous
hash resize operation this could cause a subsequent remove SA
context operation to fail as the key value used during resize is
not the same key value used when remove SA context operation is
invoked.
This commit fixes the bug by defining the SA context hash key
such that it includes only fields that never change during the
lifetime of the SA context object.
Fixes: d6c4f0298c ("net/mlx5: Refactor accel IPSec code")
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 64e2833484 ]
Querying interface FEC caps with 'ethtool [int]' after link reset
throws warning regading link speed.
This warning is not needed as there is already an indication in
user space that the link is not up.
Fixes: 0696d60853 ("net/mlx5e: Receive buffer configuration")
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 228c4cd04d ]
Loopback test had fixed packet size, which can be bigger than configured
MTU. Shorten the loopback packet size to be bigger than minimal MTU
allowed by the device. Text field removed from struct 'mlx5ehdr'
as redundant to allow send small packets as minimal allowed MTU.
Fixes: d605d66 ("net/mlx5e: Add support for ethtool self diagnostics test")
Signed-off-by: Valentine Fatiev <valentinef@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 83621b7df6 ]
We get the match level (none, l2, l3, l4) while going over the match
dissectors of an offloaded tc rule. When doing this, the match level
enum and the not min inline enum values should be used, fix that.
This worked accidentally b/c both enums have the same numerical values.
Fixes: d708f90298 ('net/mlx5e: Get the required HW match level while parsing TC flow matches')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0073c8f727 ]
In case of striding RQ, we use MPWRQ (Multi Packet WQE RQ), which means
that WQE (RX descriptor) can be used for many packets and so the WQE is
much bigger than MTU. In virtualization setups where the port mtu can
be larger than the vf mtu, if received packet is bigger than MTU, it
won't be dropped by HW on too small receive WQE. If we use linear SKB in
striding RQ, since each stride has room for mtu size payload and skb
info, an oversized packet can lead to crash for crossing allocated page
boundary upon the call to build_skb. So driver needs to check packet
size and drop it.
Introduce new SW rx counter, rx_oversize_pkts_sw_drop, which counts the
number of packets dropped by the driver for being too large.
As a new field is added to the RQ struct, re-open the channels whenever
this field is being used in datapath (i.e., in the case of linear
Striding RQ).
Fixes: 619a8f2a42 ("net/mlx5e: Use linear SKB in Striding RQ")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 077ecd785d ]
Currently, we are only supporting tc hw offloads when the eswitch
support is compiled in, but we are not gating the adevertizment
of the NETIF_F_HW_TC feature on this config being set.
Fix it, and while doing that, also avoid dealing with the feature
on ethtool when the config is not set.
Fixes: e8f887ac6a ('net/mlx5e: Introduce tc offload support')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d3a80bb5a3 ]
For the "all" ethertype we should not care whether the packet has
vlans. Besides being wrong, the way we did it caused FW error
for rules such as:
tc filter add dev eth0 protocol all parent ffff: \
prio 1 flower skip_sw action drop
b/c the matching meta-data (outer headers bit in struct mlx5_flow_spec)
wasn't set. Fix that by matching on vlan non-existence only if we were
also told to match on the ethertype.
Fixes: cee2648762 ('net/mlx5e: Set vlan masks for all offloaded TC rules')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Slava Ovsiienko <viacheslavo@mellanox.com>
Reviewed-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7cb6a2a2c7 ]
A timing hazard exists when the network interface is stopped that
allows a watchdog timeout to be processed by a separate core in
parallel. This creates the potential for the timeout handler to
wake the queues while the driver is shutting down, or access
registers after their clocks have been removed.
The more common case is that the watchdog timeout will produce a
warning message which doesn't lead to a crash. The chances of this
are greatly increased by the fact that bcm_sysport_netif_stop stops
the transmit queues which can easily precipitate a watchdog time-
out because of stale trans_start data in the queues.
This commit corrects the behavior by ensuring that the watchdog
timeout is disabled before enterring bcm_sysport_netif_stop. There
are currently only two users of the bcm_sysport_netif_stop function:
close and suspend.
The close case already handles the issue by exiting the RUNNING
state before invoking the driver close service.
The suspend case now performs the netif_device_detach to exit the
PRESENT state before the call to bcm_sysport_netif_stop rather than
after it.
These behaviors prevent any future scheduling of the driver timeout
service during the window. The netif_tx_stop_all_queues function
in bcm_sysport_netif_stop is replaced with netif_tx_disable to ensure
synchronization with any transmit or timeout threads that may
already be executing on other cores.
For symmetry, the netif_device_attach call upon resume is moved to
after the call to bcm_sysport_netif_start. Since it wakes the transmit
queues it is not necessary to invoke netif_tx_start_all_queues from
bcm_sysport_netif_start so it is moved into the driver open service.
Fixes: 40755a0fce ("net: systemport: add suspend and resume support")
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8ebebcba55 ]
When writing packets to a descriptor associated with a combined queue, the
packets should end up on that queue.
Before this change all packets written to any descriptor associated with a
tap interface end up on rx-0, even when the descriptor is associated with a
different queue.
The rx traffic can be generated by either of the following.
1. a simple tap program which spins up multiple queues and writes packets
to each of the file descriptors
2. tx from a qemu vm with a tap multiqueue netdev
The queue for rx traffic can be observed by either of the following (done
on the hypervisor in the qemu case).
1. a simple netmap program which opens and reads from per-queue
descriptors
2. configuring RPS and doing per-cpu captures with rxtxcpu
Alternatively, if you printk() the return value of skb_get_rx_queue() just
before each instance of netif_receive_skb() in tun.c, you will get 65535
for every skb.
Calling skb_record_rx_queue() to set the rx queue to the queue_index fixes
the association between descriptor and rx queue.
Signed-off-by: Matthew Cover <matthew.cover@stackpath.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 59663e4219 ]
This patch has the fix to avoid PHY lockup with 5717/5719/5720 in change
ring and flow control paths. This patch solves the RX hang while doing
continuous ring or flow control parameters with heavy traffic from peer.
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A timing hazard exists when the network interface is stopped that
allows a watchdog timeout to be processed by a separate core in
parallel. This creates the potential for the timeout handler to
wake the queues while the driver is shutting down, or access
registers after their clocks have been removed.
The more common case is that the watchdog timeout will produce a
warning message which doesn't lead to a crash. The chances of this
are greatly increased by the fact that bcmgenet_netif_stop stops
the transmit queues which can easily precipitate a watchdog time-
out because of stale trans_start data in the queues.
This commit corrects the behavior by ensuring that the watchdog
timeout is disabled before enterring bcmgenet_netif_stop. There
are currently only two users of the bcmgenet_netif_stop function:
close and suspend.
The close case already handles the issue by exiting the RUNNING
state before invoking the driver close service.
The suspend case now performs the netif_device_detach to exit the
PRESENT state before the call to bcmgenet_netif_stop rather than
after it.
These behaviors prevent any future scheduling of the driver timeout
service during the window. The netif_tx_stop_all_queues function
in bcmgenet_netif_stop is replaced with netif_tx_disable to ensure
synchronization with any transmit or timeout threads that may
already be executing on other cores.
For symmetry, the netif_device_attach call upon resume is moved to
after the call to bcmgenet_netif_start. Since it wakes the transmit
queues it is not necessary to invoke netif_tx_start_all_queues from
bcmgenet_netif_start so it is moved into the driver open service.
[ Upstream commit 09e805d257 ]
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea53abfab9 upstream.
Commit 4d2c0cda07 set slave->link to
BOND_LINK_DOWN for 802.3ad bonds whenever invalid speed/duplex values
were read, to fix a problem with slaves getting into weird states, but
in the process, broke tracking of link failures, as going straight to
BOND_LINK_DOWN when a link is indeed down (cable pulled, switch rebooted)
means we broke out of bond_miimon_inspect()'s BOND_LINK_DOWN case because
!link_state was already true, we never incremented commit, and never got
a chance to call bond_miimon_commit(), where slave->link_failure_count
would be incremented. I believe the simple fix here is to mark the slave
as BOND_LINK_FAIL, and let bond_miimon_inspect() transition the link from
_FAIL to either _UP or _DOWN, and in the latter case, we now get proper
incrementing of link_failure_count again.
Fixes: 4d2c0cda07 ("bonding: speed/duplex update at NETDEV_UP event")
CC: Mahesh Bandewar <maheshb@google.com>
CC: David S. Miller <davem@davemloft.net>
CC: netdev@vger.kernel.org
CC: stable@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d397dbe606 upstream.
Use the new of_get_compatible_child() helper to lookup the mdio child
node instead of using of_find_compatible_node(), which searches the
entire tree from a given start node and thus can return an unrelated
(i.e. non-child) node.
This also addresses a potential use-after-free (e.g. after probe
deferral) as the tree-wide helper drops a reference to its first
argument (i.e. the node of the device being probed).
Fixes: aa09677cba ("net: bcmgenet: add MDIO routines")
Cc: stable <stable@vger.kernel.org> # 3.15
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d71c3f1f5 upstream.
The rs_rate_from_ucode_rate() function may return -EINVAL if the rate
is invalid, but none of the callsites check for the error, potentially
making us access arrays with index IWL_RATE_INVALID, which is larger
than the arrays, causing an out-of-bounds access. This will trigger
KASAN warnings, such as the one reported in the bugzilla issue
mentioned below.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=200659
Cc: stable@vger.kernel.org
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5289976ad8 upstream.
If the first virtual interface is a station (or an AP with beacons
temporarily disabled), the beacon of the second interface needs to
occupy hardware beacon slot 0.
For some reason the beacon index was incorrectly masked with the
virtual interface beacon mask, which prevents the secondary
interface from sending beacons unless the first one also does.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ac63043d8c ]
Use the new of_get_compatible_child() helper to lookup the mdio-internal
child node instead of using of_find_compatible_node(), which searches
the entire tree from a given start node and thus can return an unrelated
(i.e. non-child) node.
This also addresses a potential use-after-free (e.g. after probe
deferral) as the tree-wide helper drops a reference to its first
argument (i.e. the mdio-mux node). Fortunately, this was inadvertently
balanced by a failure to drop the mdio-mux reference after lookup.
While at it, also fix the related mdio-internal- and phy-node reference
leaks.
Fixes: 634db83b82 ("net: stmmac: dwmac-sun8i: Handle integrated/external MDIOs")
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a9911937e7 ]
When running in AP mode, ath10k sometimes suffers from TX credit
starvation. The issue is hard to reproduce and shows up once in a
few days, but has been repeatedly seen with QCA9882 and a large
range of firmwares, including 10.2.4.70.67.
Once the module is in this state, TX credits are never replenished,
which results in "SWBA overrun" errors, as no beacons can be sent.
Even worse, WMI commands run in a timeout while holding the conf
mutex for three seconds each, making any further operations slow
and the whole system unresponsive.
The firmware/driver never recovers from that state automatically,
and triggering TX flush or warm restarts won't work over WMI. So
issue a hardware restart if a WMI command times out due to missing
TX credits. This implies a connectivity outage of about 1.4s in AP
mode, but brings back the interface and the whole system to a usable
state. WMI command timeouts have not been seen in absent of this
specific issue, so taking such drastic actions seems legitimate.
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 84f16fbb62 ]
RX SKBs are released in both wil6210 rmmod and RX handle.
As there is no lock to protect the buffers DMA unmap,
the SKB pointer in buff_arr is used to check if the buffer
memory was already released.
Setting wil->rx_buff_mgmt.buff_arr[buff_id].skb to NULL before the DMA
memory unmap will prevent duplicate unmapping of the same memory.
Move the buffer ID to the free list also in case the SKB is NULL.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7fb94bd58d ]
While VF2VF with RSS communication, RSS Type were wrongly recognized
and RSS hash was not calculated as it should be. Packets was
distributed on various queues by accident.
This commit fixes that behaviour and causes proper RSS Type recognition.
Signed-off-by: Sebastian Basierski <sebastianx.basierski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 47b6f50077 ]
There seems to be a problem in the x540's internal switch wherein if SR-IOV
mode is enabled and an offloaded IPsec packet is sent to a local VF,
the packet is silently dropped. This might never be a problem as it is
somewhat a corner case, but if someone happens to be using IPsec offload
from the PF to a VF that just happens to get migrated to the local box,
communication will mysteriously fail.
Not good.
A simple way to protect from this is to simply not allow any IPsec offloads
for outgoing packets when num_vfs != 0. This doesn't help any offloads that
were created before SR-IOV was enabled, but we'll get to that later.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 941ab4eb66 ]
There is a bug in FW where the sequence control may be
incorrect, and the driver overrides it with the value
of the ieee80211 header.
However, in BAR there is no sequence control in the header,
which result with arbitrary sequence.
This access to an unknown location is bad and it makes the
logs very confusing - so fix it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit baa8caf4ab ]
During testing in ARM32 platforms, observed below kernel panic, as driver
accessing data beyond the allocated memory while submitting URB to USB.
Fix: Resolved this by specifying correct length by considering 64 bit
alignment. so that, USB bus driver will access only allocated memory.
Unit-test: Tested and confirm that driver bring up and scanning,
connection and data transfer works fine with this fix.
...skipping...
[ 25.389450] Unable to handle kernel paging request at virtual
address 5aa11422
[ 25.403078] Internal error: Oops: 5 [#1] SMP ARM
[ 25.407703] Modules linked in: rsi_usb
[ 25.411473] CPU: 1 PID: 317 Comm: RX-Thread Not tainted 4.18.0-rc7 #1
[ 25.419221] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[ 25.425764] PC is at skb_release_data+0x90/0x168
[ 25.430393] LR is at skb_release_all+0x28/0x2c
[ 25.434842] pc : [<807435b0>] lr : [<80742ba0>] psr: 200e0013 5aa1141e
[ 25.464633] Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
[ 25.477524] Process RX-Thread (pid: 317, stack limit = 0x(ptrval))
[ 25.483709] Stack: (0xedf69ed8 to 0xedf6a000)
[ 25.569907] Backtrace:
[ 25.572368] [<80743520>] (skb_release_data) from [<80742ba0>]
(skb_release_all+0x28/0x2c)
[ 25.580555] r9:7f00258c r8:00000001 r7:ee355000 r6:eddab0d0
r5:eddab000 r4:eddbb840
[ 25.588308] [<80742b78>] (skb_release_all) from [<807432cc>]
(consume_skb+0x30/0x50)
[ 25.596055] r5:eddab000 r4:eddbb840
[ 25.599648] [<8074329c>] (consume_skb) from [<7f00117c>]
(rsi_usb_rx_thread+0x64/0x12c [rsi_usb])
[ 25.608524] r5:eddab000 r4:eddbb840
[ 25.612116] [<7f001118>] (rsi_usb_rx_thread [rsi_usb]) from
[<80142750>] (kthread+0x11c/0x15c)
[ 25.620735] r10:ee9ff9e0 r9:edcde3b8 r8:ee355000 r7:edf68000
r6:edd3a780 r5:00000000
[ 25.628567] r4:edcde380
[ 25.631110] [<80142634>] (kthread) from [<801010e8>]
(ret_from_fork+0x14/0x2c)
[ 25.638336] Exception stack(0xedf69fb0 to 0xedf69ff8)
[ 25.682929] ---[ end trace 8236a5496f5b5d3b ]---
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c309b15809 ]
After changing to the needed page, actually write the value to the
register!
Fixes: 09cb7dfd3f ("net: dsa: mv88e6xxx: describe PHY page and SerDes")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 41dafea2af ]
There are only 128 entries in vf vlan table, if user has added
more than 128 vlan, fw will ignore it and disable the vf vlan
table. So when user deletes the vlan entry that has not been
set to vf vlan table, fw will return not found result and driver
treat that as error, which will cause vlan delete failed problem.
This patch fixes it by returning ok when fw returns not found
result.
Fixes: 6c251711b3 ("net: hns3: Disable vf vlan filter when vf vlan table is full")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
