Signed-off-by: popcornmix <popcornmix@gmail.com>
usb: dwc: fix lockdep false positive
Signed-off-by: Kari Suvanto <karis79@gmail.com>
usb: dwc: fix inconsistent lock state
Signed-off-by: Kari Suvanto <karis79@gmail.com>
Add FIQ patch to dwc_otg driver. Enable with dwc_otg.fiq_fix_enable=1. Should give about 10% more ARM performance.
Thanks to Gordon and Costas
Avoid dynamic memory allocation for channel lock in USB driver. Thanks ddv2005.
Add NAK holdoff scheme. Enabled by default, disable with dwc_otg.nak_holdoff_enable=0. Thanks gsh
Make sure we wait for the reset to finish
dwc_otg: fix bug in dwc_otg_hcd.c resulting in silent kernel
memory corruption, escalating to OOPS under high USB load.
dwc_otg: Fix unsafe access of QTD during URB enqueue
In dwc_otg_hcd_urb_enqueue during qtd creation, it was possible that the
transaction could complete almost immediately after the qtd was assigned
to a host channel during URB enqueue, which meant the qtd pointer was no
longer valid having been completed and removed. Usually, this resulted in
an OOPS during URB submission. By predetermining whether transactions
need to be queued or not, this unsafe pointer access is avoided.
This bug was only evident on the Pi model A where a device was attached
that had no periodic endpoints (e.g. USB pendrive or some wlan devices).
dwc_otg: Fix incorrect URB allocation error handling
If the memory allocation for a dwc_otg_urb failed, the kernel would OOPS
because for some reason a member of the *unallocated* struct was set to
zero. Error handling changed to fail correctly.
dwc_otg: fix potential use-after-free case in interrupt handler
If a transaction had previously aborted, certain interrupts are
enabled to track error counts and reset where necessary. On IN
endpoints the host generates an ACK interrupt near-simultaneously
with completion of transfer. In the case where this transfer had
previously had an error, this results in a use-after-free on
the QTD memory space with a 1-byte length being overwritten to
0x00.
dwc_otg: add handling of SPLIT transaction data toggle errors
Previously a data toggle error on packets from a USB1.1 device behind
a TT would result in the Pi locking up as the driver never handled
the associated interrupt. Patch adds basic retry mechanism and
interrupt acknowledgement to cater for either a chance toggle error or
for devices that have a broken initial toggle state (FT8U232/FT232BM).
dwc_otg: implement tasklet for returning URBs to usbcore hcd layer
The dwc_otg driver interrupt handler for transfer completion will spend
a very long time with interrupts disabled when a URB is completed -
this is because usb_hcd_giveback_urb is called from within the handler
which for a USB device driver with complicated processing (e.g. webcam)
will take an exorbitant amount of time to complete. This results in
missed completion interrupts for other USB packets which lead to them
being dropped due to microframe overruns.
This patch splits returning the URB to the usb hcd layer into a
high-priority tasklet. This will have most benefit for isochronous IN
transfers but will also have incidental benefit where multiple periodic
devices are active at once.
dwc_otg: fix NAK holdoff and allow on split transactions only
This corrects a bug where if a single active non-periodic endpoint
had at least one transaction in its qh, on frnum == MAX_FRNUM the qh
would get skipped and never get queued again. This would result in
a silent device until error detection (automatic or otherwise) would
either reset the device or flush and requeue the URBs.
Additionally the NAK holdoff was enabled for all transactions - this
would potentially stall a HS endpoint for 1ms if a previous error state
enabled this interrupt and the next response was a NAK. Fix so that
only split transactions get held off.
dwc_otg: Call usb_hcd_unlink_urb_from_ep with lock held in completion handler
usb_hcd_unlink_urb_from_ep must be called with the HCD lock held. Calling it
asynchronously in the tasklet was not safe (regression in
c4564d4a1a).
This change unlinks it from the endpoint prior to queueing it for handling in
the tasklet, and also adds a check to ensure the urb is OK to be unlinked
before doing so.
NULL pointer dereference kernel oopses had been observed in usb_hcd_giveback_urb
when a USB device was unplugged/replugged during data transfer. This effect
was reproduced using automated USB port power control, hundreds of replug
events were performed during active transfers to confirm that the problem was
eliminated.
USB fix using a FIQ to implement split transactions
This commit adds a FIQ implementaion that schedules
the split transactions using a FIQ so we don't get
held off by the interrupt latency of Linux
dwc_otg: fix device attributes and avoid kernel warnings on boot
dcw_otg: avoid logging function that can cause panics
See: https://github.com/raspberrypi/firmware/issues/21
Thanks to cleverca22 for fix
dwc_otg: mask correct interrupts after transaction error recovery
The dwc_otg driver will unmask certain interrupts on a transaction
that previously halted in the error state in order to reset the
QTD error count. The various fine-grained interrupt handlers do not
consider that other interrupts besides themselves were unmasked.
By disabling the two other interrupts only ever enabled in DMA mode
for this purpose, we can avoid unnecessary function calls in the
IRQ handler. This will also prevent an unneccesary FIQ interrupt
from being generated if the FIQ is enabled.
dwc_otg: fiq: prevent FIQ thrash and incorrect state passing to IRQ
In the case of a transaction to a device that had previously aborted
due to an error, several interrupts are enabled to reset the error
count when a device responds. This has the side-effect of making the
FIQ thrash because the hardware will generate multiple instances of
a NAK on an IN bulk/interrupt endpoint and multiple instances of ACK
on an OUT bulk/interrupt endpoint. Make the FIQ mask and clear the
associated interrupts.
Additionally, on non-split transactions make sure that only unmasked
interrupts are cleared. This caused a hard-to-trigger but serious
race condition when you had the combination of an endpoint awaiting
error recovery and a transaction completed on an endpoint - due to
the sequencing and timing of interrupts generated by the dwc_otg core,
it was possible to confuse the IRQ handler.
Fix function tracing
dwc_otg: whitespace cleanup in dwc_otg_urb_enqueue
dwc_otg: prevent OOPSes during device disconnects
The dwc_otg_urb_enqueue function is thread-unsafe. In particular the
access of urb->hcpriv, usb_hcd_link_urb_to_ep, dwc_otg_urb->qtd and
friends does not occur within a critical section and so if a device
was unplugged during activity there was a high chance that the
usbcore hub_thread would try to disable the endpoint with partially-
formed entries in the URB queue. This would result in BUG() or null
pointer dereferences.
Fix so that access of urb->hcpriv, enqueuing to the hardware and
adding to usbcore endpoint URB lists is contained within a single
critical section.
dwc_otg: prevent BUG() in TT allocation if hub address is > 16
A fixed-size array is used to track TT allocation. This was
previously set to 16 which caused a crash because
dwc_otg_hcd_allocate_port would read past the end of the array.
This was hit if a hub was plugged in which enumerated as addr > 16,
due to previous device resets or unplugs.
Also add #ifdef FIQ_DEBUG around hcd->hub_port_alloc[], which grows
to a large size if 128 hub addresses are supported. This field is
for debug only for tracking which frame an allocate happened in.
dwc_otg: make channel halts with unknown state less damaging
If the IRQ received a channel halt interrupt through the FIQ
with no other bits set, the IRQ would not release the host
channel and never complete the URB.
Add catchall handling to treat as a transaction error and retry.
dwc_otg: fiq_split: use TTs with more granularity
This fixes certain issues with split transaction scheduling.
- Isochronous multi-packet OUT transactions now hog the TT until
they are completed - this prevents hubs aborting transactions
if they get a periodic start-split out-of-order
- Don't perform TT allocation on non-periodic endpoints - this
allows simultaneous use of the TT's bulk/control and periodic
transaction buffers
This commit will mainly affect USB audio playback.
dwc_otg: fix potential sleep while atomic during urb enqueue
Fixes a regression introduced with eb1b482a. Kmalloc called from
dwc_otg_hcd_qtd_add / dwc_otg_hcd_qtd_create did not always have
the GPF_ATOMIC flag set. Force this flag when inside the larger
critical section.
dwc_otg: make fiq_split_enable imply fiq_fix_enable
Failing to set up the FIQ correctly would result in
"IRQ 32: nobody cared" errors in dmesg.
dwc_otg: prevent crashes on host port disconnects
Fix several issues resulting in crashes or inconsistent state
if a Model A root port was disconnected.
- Clean up queue heads properly in kill_urbs_in_qh_list by
removing the empty QHs from the schedule lists
- Set the halt status properly to prevent IRQ handlers from
using freed memory
- Add fiq_split related cleanup for saved registers
- Make microframe scheduling reclaim host channels if
active during a disconnect
- Abort URBs with -ESHUTDOWN status response, informing
device drivers so they respond in a more correct fashion
and don't try to resubmit URBs
- Prevent IRQ handlers from attempting to handle channel
interrupts if the associated URB was dequeued (and the
driver state was cleared)
dwc_otg: prevent leaking URBs during enqueue
A dwc_otg_urb would get leaked if the HCD enqueue function
failed for any reason. Free the URB at the appropriate points.
dwc_otg: Enable NAK holdoff for control split transactions
Certain low-speed devices take a very long time to complete a
data or status stage of a control transaction, producing NAK
responses until they complete internal processing - the USB2.0
spec limit is up to 500mS. This causes the same type of interrupt
storm as seen with USB-serial dongles prior to c8edb238.
In certain circumstances, usually while booting, this interrupt
storm could cause SD card timeouts.
dwc_otg: Fix for occasional lockup on boot when doing a USB reset
dwc_otg: Don't issue traffic to LS devices in FS mode
Issuing low-speed packets when the root port is in full-speed mode
causes the root port to stop responding. Explicitly fail when
enqueuing URBs to a LS endpoint on a FS bus.
Fix ARM architecture issue with local_irq_restore()
If local_fiq_enable() is called before a local_irq_restore(flags) where
the flags variable has the F bit set, the FIQ will be erroneously disabled.
Fixup arch_local_irq_restore to avoid trampling the F bit in CPSR.
Also fix some of the hacks previously implemented for previous dwc_otg
incarnations.
dwc_otg: fiq_fsm: Base commit for driver rewrite
This commit removes the previous FIQ fixes entirely and adds fiq_fsm.
This rewrite features much more complete support for split transactions
and takes into account several OTG hardware bugs. High-speed
isochronous transactions are also capable of being performed by fiq_fsm.
All driver options have been removed and replaced with:
- dwc_otg.fiq_enable (bool)
- dwc_otg.fiq_fsm_enable (bool)
- dwc_otg.fiq_fsm_mask (bitmask)
- dwc_otg.nak_holdoff (unsigned int)
Defaults are specified such that fiq_fsm behaves similarly to the
previously implemented FIQ fixes.
fiq_fsm: Push error recovery into the FIQ when fiq_fsm is used
If the transfer associated with a QTD failed due to a bus error, the HCD
would retry the transfer up to 3 times (implementing the USB2.0
three-strikes retry in software).
Due to the masking mechanism used by fiq_fsm, it is only possible to pass
a single interrupt through to the HCD per-transfer.
In this instance host channels would fall off the radar because the error
reset would function, but the subsequent channel halt would be lost.
Push the error count reset into the FIQ handler.
fiq_fsm: Implement timeout mechanism
For full-speed endpoints with a large packet size, interrupt latency
runs the risk of the FIQ starting a transaction too late in a full-speed
frame. If the device is still transmitting data when EOF2 for the
downstream frame occurs, the hub will disable the port. This change is
not reflected in the hub status endpoint and the device becomes
unresponsive.
Prevent high-bandwidth transactions from being started too late in a
frame. The mechanism is not guaranteed: a combination of bit stuffing
and hub latency may still result in a device overrunning.
fiq_fsm: fix bounce buffer utilisation for Isochronous OUT
Multi-packet isochronous OUT transactions were subject to a few bounday
bugs. Fix them.
Audio playback is now much more robust: however, an issue stands with
devices that have adaptive sinks - ALSA plays samples too fast.
dwc_otg: Return full-speed frame numbers in HS mode
The frame counter increments on every *microframe* in high-speed mode.
Most device drivers expect this number to be in full-speed frames - this
caused considerable confusion to e.g. snd_usb_audio which uses the
frame counter to estimate the number of samples played.
fiq_fsm: save PID on completion of interrupt OUT transfers
Also add edge case handling for interrupt transports.
Note that for periodic split IN, data toggles are unimplemented in the
OTG host hardware - it unconditionally accepts any PID.
fiq_fsm: add missing case for fiq_fsm_tt_in_use()
Certain combinations of bitrate and endpoint activity could
result in a periodic transaction erroneously getting started
while the previous Isochronous OUT was still active.
fiq_fsm: clear hcintmsk for aborted transactions
Prevents the FIQ from erroneously handling interrupts
on a timed out channel.
fiq_fsm: enable by default
fiq_fsm: fix dequeues for non-periodic split transactions
If a dequeue happened between the SSPLIT and CSPLIT phases of the
transaction, the HCD would never receive an interrupt.
fiq_fsm: Disable by default
fiq_fsm: Handle HC babble errors
The HCTSIZ transfer size field raises a babble interrupt if
the counter wraps. Handle the resulting interrupt in this case.
dwc_otg: fix interrupt registration for fiq_enable=0
Additionally make the module parameter conditional for wherever
hcd->fiq_state is touched.
fiq_fsm: Enable by default
dwc_otg: Fix various issues with root port and transaction errors
Process the host port interrupts correctly (and don't trample them).
Root port hotplug now functional again.
Fix a few thinkos with the transaction error passthrough for fiq_fsm.
fiq_fsm: Implement hack for Split Interrupt transactions
Hubs aren't too picky about which endpoint we send Control type split
transactions to. By treating Interrupt transfers as Control, it is
possible to use the non-periodic queue in the OTG core as well as the
non-periodic FIFOs in the hub itself. This massively reduces the
microframe exclusivity/contention that periodic split transactions
otherwise have to enforce.
It goes without saying that this is a fairly egregious USB specification
violation, but it works.
Original idea by Hans Petter Selasky @ FreeBSD.org.
dwc_otg: FIQ support on SMP. Set up FIQ stack and handler on Core 0 only.
dwc_otg: introduce fiq_fsm_spin(un|)lock()
SMP safety for the FIQ relies on register read-modify write cycles being
completed in the correct order. Several places in the DWC code modify
registers also touched by the FIQ. Protect these by a bare-bones lock
mechanism.
This also makes it possible to run the FIQ and IRQ handlers on different
cores.
fiq_fsm: fix build on bcm2708 and bcm2709 platforms
dwc_otg: put some barriers back where they should be for UP
bcm2709/dwc_otg: Setup FIQ on core 1 if >1 core active
dwc_otg: fixup read-modify-write in critical paths
Be more careful about read-modify-write on registers that the FIQ
also touches.
Guard fiq_fsm_spin_lock with fiq_enable check
fiq_fsm: Falling out of the state machine isn't fatal
This edge case can be hit if the port is disabled while the FIQ is
in the middle of a transaction. Make the effects less severe.
Also get rid of the useless return value.
squash: dwc_otg: Allow to build without SMP
usb: core: make overcurrent messages more prominent
Hub overcurrent messages are more serious than "debug". Increase loglevel.
usb: dwc_otg: Don't use dma_to_virt()
Commit 6ce0d20 changes dma_to_virt() which breaks this driver.
Open code the old dma_to_virt() implementation to work around this.
Limit the use of __bus_to_virt() to cases where transfer_buffer_length
is set and transfer_buffer is not set. This is done to increase the
chance that this driver will also work on ARCH_BCM2835.
transfer_buffer should not be NULL if the length is set, but the
comment in the code indicates that there are situations where this
might happen. drivers/usb/isp1760/isp1760-hcd.c also has a similar
comment pointing to a possible: 'usb storage / SCSI bug'.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Fix crash when fiq_enable=0
dwc_otg: fiq_fsm: Make high-speed isochronous strided transfers work properly
Certain low-bandwidth high-speed USB devices (specialist audio devices,
compressed-frame webcams) have packet intervals > 1 microframe.
Stride these transfers in the FIQ by using the start-of-frame interrupt
to restart the channel at the right time.
dwc_otg: Force host mode to fix incorrect compute module boards
dwc_otg: Add ARCH_BCM2835 support
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Simplify FIQ irq number code
Dropping ATAGS means we can simplify the FIQ irq number code.
Also add error checking on the returned irq number.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Remove duplicate gadget probe/unregister function
dwc_otg: Properly set the HFIR
Douglas Anderson reported:
According to the most up to date version of the dwc2 databook, the FRINT
field of the HFIR register should be programmed to:
* 125 us * (PHY clock freq for HS) - 1
* 1000 us * (PHY clock freq for FS/LS) - 1
This is opposed to older versions of the doc that claimed it should be:
* 125 us * (PHY clock freq for HS)
* 1000 us * (PHY clock freq for FS/LS)
and reported lower timing jitter on a USB analyser
dcw_otg: trim xfer length when buffer larger than allocated size is received
dwc_otg: Don't free qh align buffers in atomic context
dwc_otg: Enable the hack for Split Interrupt transactions by default
dwc_otg.fiq_fsm_mask=0xF has long been a suggestion for users with audio stutters or other USB bandwidth issues.
So far we are aware of many success stories but no failure caused by this setting.
Make it a default to learn more.
See: https://www.raspberrypi.org/forums/viewtopic.php?f=28&t=70437
Signed-off-by: popcornmix <popcornmix@gmail.com>
dwc_otg: Use kzalloc when suitable
dwc_otg: Pass struct device to dma_alloc*()
This makes it possible to get the bus address from Device Tree.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: fix summarize urb->actual_length for isochronous transfers
Kernel does not copy input data of ISO transfers to userspace
if actual_length is set only in ISO transfers and not summarized
in urb->actual_length. Fixesraspberrypi/linux#903
fiq_fsm: Use correct states when starting isoc OUT transfers
In fiq_fsm_start_next_periodic() if an isochronous OUT transfer
was selected, no regard was given as to whether this was a single-packet
transfer or a multi-packet staged transfer.
For single-packet transfers, this had the effect of repeatedly sending
OUT packets with bogus data and lengths.
Eventually if the channel was repeatedly enabled enough times, this
would lock up the OTG core and no further bus transfers would happen.
Set the FSM state up properly if we select a single-packet transfer.
Fixes https://github.com/raspberrypi/linux/issues/1842
dwc_otg: make nak_holdoff work as intended with empty queues
If URBs reading from non-periodic split endpoints were dequeued and
the last transfer from the endpoint was a NAK handshake, the resulting
qh->nak_frame value was stale which would result in unnecessarily long
polling intervals for the first subsequent transfer with a fresh URB.
Fixup qh->nak_frame in dwc_otg_hcd_urb_dequeue and also guard against
a case where a single URB is submitted to the endpoint, a NAK was
received on the transfer immediately prior to receiving data and the
device subsequently resubmits another URB past the qh->nak_frame interval.
Fixes https://github.com/raspberrypi/linux/issues/1709
dwc_otg: fix split transaction data toggle handling around dequeues
See https://github.com/raspberrypi/linux/issues/1709
Fix several issues regarding endpoint state when URBs are dequeued
- If the HCD is disconnected, flush FIQ-enabled channels properly
- Save the data toggle state for bulk endpoints if the last transfer
from an endpoint where URBs were dequeued returned a data packet
- Reset hc->start_pkt_count properly in assign_and_init_hc()
dwc_otg: fix several potential crash sources
On root port disconnect events, the host driver state is cleared and
in-progress host channels are forcibly stopped. This doesn't play
well with the FIQ running in the background, so:
- Guard the disconnect callback with both the host spinlock and FIQ
spinlock
- Move qtd dereference in dwc_otg_handle_hc_fsm() after the early-out
so we don't dereference a qtd that has gone away
- Turn catch-all BUG()s in dwc_otg_handle_hc_fsm() into warnings.
dwc_otg: delete hcd->channel_lock
The lock serves no purpose as it is only held while the HCD spinlock
is already being held.
dwc_otg: remove unnecessary dma-mode channel halts on disconnect interrupt
Host channels are already halted in kill_urbs_in_qh_list() with the
subsequent interrupt processing behaving as if the URB was dequeued
via HCD callback.
There's no need to clobber the host channel registers a second time
as this exposes races between the driver and host channel resulting
in hcd->free_hc_list becoming corrupted.
dwcotg: Allow to build without FIQ on ARM64
Signed-off-by: popcornmix <popcornmix@gmail.com>
dwc_otg: make periodic scheduling behave properly for FS buses
If the root port is in full-speed mode, transfer times at 12mbit/s
would be calculated but matched against high-speed quotas.
Reinitialise hcd->frame_usecs[i] on each port enable event so that
full-speed bandwidth can be tracked sensibly.
Also, don't bother using the FIQ for transfers when in full-speed
mode - at the slower bus speed, interrupt frequency is reduced by
an order of magnitude.
Related issue: https://github.com/raspberrypi/linux/issues/2020
dwc_otg: fiq_fsm: Make isochronous compatibility checks work properly
Get rid of the spammy printk and local pointer mangling.
Also, there is a nominal benefit for using fiq_fsm for isochronous
transfers in FS mode (~1.1k IRQs per second vs 2.1k IRQs per second)
so remove the root port speed check.
dwc_otg: add module parameter int_ep_interval_min
Add a module parameter (defaulting to ignored) that clamps the polling rate
of high-speed Interrupt endpoints to a minimum microframe interval.
The parameter is modifiable at runtime as it is used when activating new
endpoints (such as on device connect).
dwc_otg: fiq_fsm: Add non-periodic TT exclusivity constraints
Certain hub types do not discriminate between pipe direction (IN or OUT)
when considering non-periodic transfers. Therefore these hubs get confused
if multiple transfers are issued in different directions with the same
device address and endpoint number.
Constrain queuing non-periodic split transactions so they are performed
serially in such cases.
Related: https://github.com/raspberrypi/linux/issues/2024
dwc_otg: Fixup change to DRIVER_ATTR interface
dwc_otg: Fix compilation warnings
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
USB_DWCOTG: Disable building dwc_otg as a module (#2265)
When dwc_otg is built as a module, build will fail with the following
error:
ERROR: "DWC_TASK_HI_SCHEDULE" [drivers/usb/host/dwc_otg/dwc_otg.ko] undefined!
scripts/Makefile.modpost:91: recipe for target '__modpost' failed
make[1]: *** [__modpost] Error 1
Makefile:1199: recipe for target 'modules' failed
make: *** [modules] Error 2
Even if the error is solved by including the missing
DWC_TASK_HI_SCHEDULE function, the kernel will panic when loading
dwc_otg.
As a workaround, simply prevent user from building dwc_otg as a module
as the current kernel does not support it.
See: https://github.com/raspberrypi/linux/issues/2258
Signed-off-by: Malik Olivier Boussejra <malik@boussejra.com>
dwc_otg: New timer API
dwc_otg: Fix removed ACCESS_ONCE->READ_ONCE
dwc_otg: don't unconditionally force host mode in dwc_otg_cil_init()
Add the ability to disable force_host_mode for those that want to use
dwc_otg in both device and host modes.
dwc_otg: Fix a regression when dequeueing isochronous transfers
In 282bed95 (dwc_otg: make nak_holdoff work as intended with empty queues)
the dequeue mechanism was changed to leave FIQ-enabled transfers to run
to completion - to avoid leaving hub TT buffers with stale packets lying
around.
This broke FIQ-accelerated isochronous transfers, as this then meant that
dozens of transfers were performed after the dequeue function returned.
Restore the state machine fence for isochronous transfers.
fiq_fsm: rewind DMA pointer for OUT transactions that fail (#2288)
See: https://github.com/raspberrypi/linux/issues/2140
dwc_otg: add smp_mb() to prevent driver state corruption on boot
Occasional crashes have been seen where the FIQ code dereferences
invalid/random pointers immediately after being set up, leading to
panic on boot.
The crash occurs as the FIQ code races against hcd_init_fiq() and
the hcd_init_fiq() code races against the outstanding memory stores
from dwc_otg_hcd_init(). Use explicit barriers after touching
driver state.
usb: dwc_otg: fix memory corruption in dwc_otg driver
[Upstream commit 51b1b64917]
The move from the staging tree to the main tree exposed a
longstanding memory corruption bug in the dwc2 driver. The
reordering of the driver initialization caused the dwc2 driver
to corrupt the initialization data of the sdhci driver on the
Raspberry Pi platform, which made the bug show up.
The error is in calling to_usb_device(hsotg->dev), since ->dev
is not a member of struct usb_device. The easiest fix is to
just remove the offending code, since it is not really needed.
Thanks to Stephen Warren for tracking down the cause of this.
Reported-by: Andre Heider <a.heider@gmail.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[lukas: port from upstream dwc2 to out-of-tree dwc_otg driver]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
usb: dwb_otg: Fix unreachable switch statement warning
This warning appears with GCC 7.3.0 from toolchains.bootlin.com:
../drivers/usb/host/dwc_otg/dwc_otg_fiq_fsm.c: In function ‘fiq_fsm_update_hs_isoc’:
../drivers/usb/host/dwc_otg/dwc_otg_fiq_fsm.c:595:61: warning: statement will never be executed [-Wswitch-unreachable]
st->hctsiz_copy.b.xfersize = nrpackets * st->hcchar_copy.b.mps;
~~~~~~~~~~~~~~~~~^~~~
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
dwc_otg: fiq_fsm: fix incorrect DMA register offset calculation
Rationalise the offset and update all call sites.
Fixes https://github.com/raspberrypi/linux/issues/2408
[ Upstream commit e86108940e ]
When initializing a hub we want to give a USB3 port in link training
the same debounce delay time before autosuspening the hub as already
trained, connected enabled ports.
USB3 ports won't reach the enabled state with "current connect status" and
"connect status change" bits set until the USB3 link training finishes.
Catching the port in link training (polling) and adding the debounce delay
prevents unnecessary failed attempts to autosuspend the hub.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 22454b79e6 upstream.
This will clear the USB_PORT_FEAT_C_CONNECTION bit in case of a hub port reset
only if a device is was attached to the hub port before resetting the hub port.
Using a Lenovo T480s attached to the ultra dock it was not possible to detect
some usb-c devices at the dock usb-c ports because the hub_port_reset code
will clear the USB_PORT_FEAT_C_CONNECTION bit after the actual hub port reset.
Using this device combo the USB_PORT_FEAT_C_CONNECTION bit was set between the
actual hub port reset and the clear of the USB_PORT_FEAT_C_CONNECTION bit.
This ends up with clearing the USB_PORT_FEAT_C_CONNECTION bit after the
new device was attached such that it was not detected.
This patch will not clear the USB_PORT_FEAT_C_CONNECTION bit if there is
currently no device attached to the port before the hub port reset.
This will avoid clearing the connection bit for new attached devices.
Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 781f0766cc upstream.
Devices connected under Terminus Technology Inc. Hub (1a40:0101) may
fail to work after the system resumes from suspend:
[ 206.063325] usb 3-2.4: reset full-speed USB device number 4 using xhci_hcd
[ 206.143691] usb 3-2.4: device descriptor read/64, error -32
[ 206.351671] usb 3-2.4: device descriptor read/64, error -32
Info for this hub:
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=480 MxCh= 4
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1a40 ProdID=0101 Rev=01.11
S: Product=USB 2.0 Hub
C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
Some expirements indicate that the USB devices connected to the hub are
innocent, it's the hub itself is to blame. The hub needs extra delay
time after it resets its port.
Hence wait for extra delay, if the device is connected to this quirky
hub.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on USB2.0 Spec Section 11.12.5,
"If a hub has per-port power switching and per-port current limiting,
an over-current on one port may still cause the power on another port
to fall below specific minimums. In this case, the affected port is
placed in the Power-Off state and C_PORT_OVER_CURRENT is set for the
port, but PORT_OVER_CURRENT is not set."
so let's check C_PORT_OVER_CURRENT too for over current condition.
Fixes: 08d1dec6f4 ("usb:hub set hub->change_bits when over-current happens")
Cc: <stable@vger.kernel.org>
Tested-by: Alessandro Antenucci <antenucci@korg.it>
Signed-off-by: Bin Liu <b-liu@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a USB device attached to a root-hub port sends a wakeup request
to a sleeping system, we do not report the wakeup event to the PM
core. This is because a system resume involves waking up all
suspended USB ports as quickly as possible; without the normal
USB_RESUME_TIMEOUT delay, the host controller driver doesn't set the
USB_PORT_STAT_C_SUSPEND flag and so usb_port_resume() doesn't realize
that a wakeup request was received.
However, some environments (such as Chrome OS) want to have all wakeup
events reported so they can be ascribed to the appropriate device. To
accommodate these environments, this patch adds a new routine to the
hub driver and a corresponding new HCD method to be used when a root
hub resumes. The HCD method returns a bitmap of ports that have
initiated a wakeup signal but not yet completed resuming. The hub
driver can then report to the PM core that the child devices attached
to these ports initiated a wakeup event.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the USB hub core waits for 50 ms after enumerating the
device. This was added to help "some high speed devices" to
enumerate (b789696af8 "[PATCH] USB: relax usbcore reset timings").
On some devices, the time-to-active is important, so we provide
a per-port option to reduce the time to what the USB specification
requires: 10 ms.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "old" enumeration scheme is considerably faster (it takes
~244ms instead of ~356ms to get the descriptor).
It is currently only possible to use the old scheme globally
(/sys/module/usbcore/parameters/old_scheme_first), which is not
desirable as the new scheme was introduced to increase compatibility
with more devices.
However, in our case, we care about time-to-active for a specific
USB device (which we make the firmware for), on a specific port
(that is pogo-pin based: not a standard USB port). This new
sysfs option makes it possible to use the old scheme on a single
port only.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some low-speed and full-speed devices (for example, bluetooth)
do not have time to initialize. For them, ETIMEDOUT is a valid error.
We need to give them another try. Otherwise, they will
never be initialized correctly and in dmesg will be messages
"Bluetooth: hci0 command 0x1002 tx timeout" or similars.
Fixes: 264904ccc3 ("usb: retry reset if a device times out")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Maxim Moseychuk <franchesko.salias.hudro.pedros@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB 3.2 specification adds a Gen XxY notion for USB3 devices where
X is the signaling rate on the wire. Gen 1xY is 5Gbps Superspeed
and Gen 2xY is 10Gbps SuperSpeedPlus. Y is the lane count.
For normal, non inter-chip (SSIC) devies the rx and tx lane count is
symmetric, and the maximum lane count for USB 3.2 devices is 2 (dual-lane).
SSIC devices may have asymmetric lane counts, with up to four
lanes per direction. The USB 3.2 specification doesn't point out
how to use the Gen XxY notion for these devices, so we limit the Gen Xx2
notion to symmertic Dual lane devies.
For other devices just show Gen1 or Gen2
Gen 1 5Gbps
Gen 2 10Gbps
Gen 1x2 10Gbps Dual-lane (USB 3.2)
Gen 2x2 20Gbps Dual-lane (USB 3.2)
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB 3.2 specification adds Dual-lane support, doubling the maximum
SuperSpeedPlus data rate from 10Gbps to 20Gbps.
Dual-lane takes into use a second set of rx and tx wires/pins in the
Type-C cable and connector.
Add "rx_lanes" and "tx_lanes" variables to struct usb_device to store
the numer of lanes in use. Number of lanes can be read using the extended
port status hub request that was introduced in USB 3.1.
Extended port status rx and tx lane count are zero based, maximum
lanes supported by non inter-chip (SSIC) USB 3.2 is 2 (dual lane) with
rx and tx lane count symmetric. SSIC devices support asymmetric lanes
up to 4 lanes per direction.
If extended port status is not available then default to one lane.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wait_for_connected() wait till a port change status to
USB_PORT_STAT_CONNECTION, but this is not possible if
the port is unpowered. The loop will only exit at timeout.
Such case take place if an over-current incident happen
while system is in S3. Then during resume wait_for_connected()
will wait 2s, which may be noticeable by the user.
Signed-off-by: Dominik Bozek <dominikx.bozek@intel.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On chromebooks we depend on wakeup count to identify the wakeup source.
But currently USB devices do not increment the wakeup count when they
trigger the remote wake. This patch addresses the same.
Resume condition is reported differently on USB 2.0 and USB 3.0 devices.
On USB 2.0 devices, a wake capable device, if wake enabled, drives
resume signal to indicate a remote wake (USB 2.0 spec section 7.1.7.7).
The upstream facing port then sets C_PORT_SUSPEND bit and reports a
port change event (USB 2.0 spec section 11.24.2.7.2.3). Thus if a port
has resumed before driving the resume signal from the host and
C_PORT_SUSPEND is set, then the device attached to the given port might
be the reason for the last system wakeup. Increment the wakeup count for
the same.
On USB 3.0 devices, a function may signal that it wants to exit from device
suspend by sending a Function Wake Device Notification to the host (USB3.0
spec section 8.5.6.4) Thus on receiving the Function Wake, increment the
wakeup count.
Signed-off-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Print bcdDevice which is used by vendors to identify different versions
of the same product (or different versions of firmware).
Adding this to the logs will be useful for support purposes.
Match the %2x.%02x formatting that's used by lsusb -v for this same value.
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we warn the user when the root hub lost power after resume,
but the user cannot do anything about it so it should probably be a
notice.
This will reduce the noise in the console during suspend and resume,
which is already quite significant in many systems.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For some userspace applications information on the number of
over-current conditions at specific USB hub ports is relevant.
In our case we have a series of USB hardware (using the cp210x driver)
which communicates using a proprietary protocol. These devices sometimes
trigger an over-current situation on some hubs. In case of such an
over-current situation the USB devices offer an interface for reducing
the max used power. As these conditions are quite rare and imply
performance reductions of the device we don't want to reduce the max
power always.
Therefore give user-space applications the possibility to react
adequately by introducing an over_current_counter in the usb port struct
which is exported via sysfs.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disabing Latency Tolerance Messaging before port reset is unnecessary.
LTM is automatically disabled at port reset.
If host can't communicate with the device the LTM message will fail, and
the hub driver will unnecessarily do a logical disconnect.
Broken communication is ofter the reason for a reset in the first place.
Additionally we can't guarantee device is in a configured state,
epecially in reset-resume case when root hub lost power.
LTM can't be modified unless device is in a configured state.
Just remove LTM disabling before port reset.
Details about LTM and port reset in USB 3 specification:
USB 3 spec section 9.4.5
"The LTM Enable field can be modified by the SetFeature() and
ClearFeature() requests using the LTM_ENABLE feature selector.
This field is reset to zero when the device is reset."
USB 3 spec section 9.4.1
"The device shall process a Clear Feature (U1_Enable or U2_Enable or
LTM_Enable) only if the device is in the configured state."
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB SS and SSP hubs provide wHubDelay values on their hub descriptor
which we should inform the USB Device about.
The USB Specification 3.0 explains, on section 9.4.11, how to
calculate the value and how to issue the request. Note that a
USB_REQ_SET_ISOCH_DELAY is valid on all device states (Default,
Address, Configured), we just *chose* to issue it from Address state
right after successfully fetching the USB Device Descriptor.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using a period after a newline causes bad output.
Miscellanea:
o Coalesce formats too
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes the USB device gets confused about the state of the initialization and
the connection fails. In particular, the device thinks that it's already set up
and running while the host thinks the device still needs to be configured. To
work around this issue, power-cycle the hub's output to issue a sort of "reset"
to the device. This makes the device restart its state machine and then the
initialization succeeds.
This fixes problems where the kernel reports a list of errors like this:
usb 1-1.3: device not accepting address 19, error -71
The end result is a non-functioning device. After this patch, the sequence
becomes like this:
usb 1-1.3: new high-speed USB device number 18 using ci_hdrc
usb 1-1.3: device not accepting address 18, error -71
usb 1-1.3: new high-speed USB device number 19 using ci_hdrc
usb 1-1.3: device not accepting address 19, error -71
usb 1-1-port3: attempt power cycle
usb 1-1.3: new high-speed USB device number 21 using ci_hdrc
usb-storage 1-1.3:1.2: USB Mass Storage device detected
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This new helper is a simple wrapper around usb_get_status(). This
patch is in preparation to adding support for fetching PTM_STATUS
types. No functional changes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To match the rest of the kernel, the SPDX tags for the drivers/usb/core/
files are moved to the first line of the file. This makes it more
obvious the tag is present as well as making it match the other 12k
files in the tree with this location.
It also uses // to match the "expected style" as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the connect status change is set during reset signaling, but
the status remains connected just retry port reset.
This solves an issue with connecting a 90W HP Thunderbolt 3 dock
with a Lenovo Carbon x1 (5th generation) which causes a 30min loop
of a high speed device being re-discovererd before usb ports starts
working.
[...]
[ 389.023845] usb 3-1: new high-speed USB device number 55 using xhci_hcd
[ 389.491841] usb 3-1: new high-speed USB device number 56 using xhci_hcd
[ 389.959928] usb 3-1: new high-speed USB device number 57 using xhci_hcd
[...]
This is caused by a high speed device that doesn't successfully go to the
enabled state after the second port reset. Instead the connection bounces
(connected, with connect status change), bailing out completely from
enumeration just to restart from scratch.
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1716332
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e0429362ab
("usb: Add device quirk for Logitech HD Pro Webcams C920 and C930e")
introduced quirk to workaround an issue with some Logitech webcams.
The workaround is introducing delay for some USB operations.
According to our testing, delay introduced by original commit
is not long enough and in rare cases we still see issues described
by the aforementioned commit.
This patch increases delays introduced by original commit.
Having this patch applied we do not see those problems anymore.
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Save 80ms device enumeration time by increasing root hub port reset time
The 50ms reset signaling time is not enough for most root hub ports.
Increasing the reset time to 60ms allows host controllers to finish port
reset and removes a retry causing an extra 50ms delay.
The USB 2 specification requires "at least 50ms" for driving root
port reset. The current msleep is exactly 50ms which may not be
enough if there are any delays between writing the reset bit to host
controller portsc register and phy actually driving reset.
On Haswell, Skylake and Kabylake xHC port reset took in average 52-59ms
The 80ms improvement comes from (40ms * 2 port resets) save at enumeration
for each device connected to a root hub port.
more details about root port reset in USB2 section 7.1.7.5:.
"Software must ensure that resets issued to the root ports drive reset
long enough to overwhelm any concurrent resume attempts by downstream
devices. It is required that resets from root ports have a duration of
at least 50 ms (TDRSTR).
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some buggy USB disk adapters disconnect and reconnect multiple times
during the enumeration procedure. This may lead to a device
connecting at full speed instead of high speed, because when the USB
stack sees that a device isn't able to enumerate at high speed, it
tries to hand the connection over to a full-speed companion
controller.
The logic for doing this is careful to check that the device is still
connected. But this check is inadequate if the device disconnects and
reconnects before the check is done. The symptom is that a device
works, but much more slowly than it is capable of operating.
The situation was made worse recently by commit 22547c4cc4 ("usb:
hub: Wait for connection to be reestablished after port reset"), which
increases the delay following a reset before a disconnect is
recognized, thus giving the device more time to reconnect.
This patch makes the check more robust. If the device was
disconnected at any time during enumeration, we will now skip the
full-speed handover.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Zdenek Kabelac <zkabelac@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The controller driver may be NULL if the controller device
is the middle device between platform device and roothub.
This middle device may not need a device driver due to all
hardware control can be at platform device driver, this
platform device is usually a dual-role USB controller device.
The benefit of using this middle device is we can keep both
controller device's private data (known as struct usb_hcd)
for USB core use, and platform device's private data for
platform driver use.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rework smelling code (goto inside compound statement). Perhaps this is
legacy. Anyway such code is not appropriate for Linux kernel.
Signed-off-by: Eugene Korenevsky <ekorenevsky@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original motivation for disabling/enabling Link PM at device
suspend/resume was to force link state to go via U0 before suspend sets
the link state to U3. Going directly from U2 to U3 is not allowed.
Disabling LPM will forced the link state to U0, but will send a lot of
Set port feature requests for evert suspend and resume.
This is not needed as Hub hardware will take care of going via U0
when a U2 -> U3 transition is requested [1]
[1] USB 3.1 specification section 10.16.2.10 Set Port Feature:
"If the value is 3, then host software wants to selectively suspend the
device connected to this port. The hub shall transition the link to U3
from any of the other U states using allowed link state transitions.
If the port is not already in the U0 state, then it shall transition the
port to the U0 state and then initiate the transition to U3.
While this state is active, the hub does not propagate downstream-directed
traffic to this port, but the hub will respond to resume signaling from the
port"
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add define for the maximum number of ports on a SuperSpeed hub as per
USB 3.1 spec Table 10-5, and use it when verifying the retrieved hub
descriptor.
This specifically avoids benign attempts to update the DeviceRemovable
mask for non-existing ports (should we get that far).
Fixes: dbe79bbe9d ("USB 3.0 Hub Changes")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing sanity check on the non-SuperSpeed hub-descriptor length in
order to avoid parsing and leaking two bytes of uninitialised slab data
through sysfs removable-attributes (or a compound-device debug
statement).
Note that we only make sure that the DeviceRemovable field is always
present (and specifically ignore the unused PortPwrCtrlMask field) in
order to continue support any hubs with non-compliant descriptors. As a
further safeguard, the descriptor buffer is also cleared.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org> # 2.6.12
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A SuperSpeed hub descriptor does not have any variable-length fields so
bail out when reading a short descriptor.
This avoids parsing and leaking two bytes of uninitialised slab data
through sysfs removable-attributes.
Fixes: dbe79bbe9d ("USB 3.0 Hub Changes")
Cc: stable <stable@vger.kernel.org> # 2.6.39
Cc: John Youn <John.Youn@synopsys.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves a merge issue in the gadget code, and we want the USB
fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While running a bind/unbind stress test with the dwc3 usb driver on rk3399,
the following crash was observed.
Unable to handle kernel NULL pointer dereference at virtual address 00000218
pgd = ffffffc00165f000
[00000218] *pgd=000000000174f003, *pud=000000000174f003,
*pmd=0000000001750003, *pte=00e8000001751713
Internal error: Oops: 96000005 [#1] PREEMPT SMP
Modules linked in: uinput uvcvideo videobuf2_vmalloc cmac
ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat rfcomm
xt_mark fuse bridge stp llc zram btusb btrtl btbcm btintel bluetooth
ip6table_filter mwifiex_pcie mwifiex cfg80211 cdc_ether usbnet r8152 mii joydev
snd_seq_midi snd_seq_midi_event snd_rawmidi snd_seq snd_seq_device ppp_async
ppp_generic slhc tun
CPU: 1 PID: 29814 Comm: kworker/1:1 Not tainted 4.4.52 #507
Hardware name: Google Kevin (DT)
Workqueue: pm pm_runtime_work
task: ffffffc0ac540000 ti: ffffffc0af4d4000 task.ti: ffffffc0af4d4000
PC is at autosuspend_check+0x74/0x174
LR is at autosuspend_check+0x70/0x174
...
Call trace:
[<ffffffc00080dcc0>] autosuspend_check+0x74/0x174
[<ffffffc000810500>] usb_runtime_idle+0x20/0x40
[<ffffffc000785ae0>] __rpm_callback+0x48/0x7c
[<ffffffc000786af0>] rpm_idle+0x1e8/0x498
[<ffffffc000787cdc>] pm_runtime_work+0x88/0xcc
[<ffffffc000249bb8>] process_one_work+0x390/0x6b8
[<ffffffc00024abcc>] worker_thread+0x480/0x610
[<ffffffc000251a80>] kthread+0x164/0x178
[<ffffffc0002045d0>] ret_from_fork+0x10/0x40
Source:
(gdb) l *0xffffffc00080dcc0
0xffffffc00080dcc0 is in autosuspend_check
(drivers/usb/core/driver.c:1778).
1773 /* We don't need to check interfaces that are
1774 * disabled for runtime PM. Either they are unbound
1775 * or else their drivers don't support autosuspend
1776 * and so they are permanently active.
1777 */
1778 if (intf->dev.power.disable_depth)
1779 continue;
1780 if (atomic_read(&intf->dev.power.usage_count) > 0)
1781 return -EBUSY;
1782 w |= intf->needs_remote_wakeup;
Code analysis shows that intf is set to NULL in usb_disable_device() prior
to setting actconfig to NULL. At the same time, usb_runtime_idle() does not
lock the usb device, and neither does any of the functions in the
traceback. This means that there is no protection against a race condition
where usb_disable_device() is removing dev->actconfig->interface[] pointers
while those are being accessed from autosuspend_check().
To solve the problem, synchronize and validate device state between
autosuspend_check() and usb_disconnect().
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If usb_get_bos_descriptor() returns an error, usb->bos will be NULL.
Nevertheless, it is dereferenced unconditionally in
hub_set_initial_usb2_lpm_policy() if usb2_hw_lpm_capable is set.
This results in a crash.
usb 5-1: unable to get BOS descriptor
...
Unable to handle kernel NULL pointer dereference at virtual address 00000008
pgd = ffffffc00165f000
[00000008] *pgd=000000000174f003, *pud=000000000174f003,
*pmd=0000000001750003, *pte=00e8000001751713
Internal error: Oops: 96000005 [#1] PREEMPT SMP
Modules linked in: uinput uvcvideo videobuf2_vmalloc cmac [ ... ]
CPU: 5 PID: 3353 Comm: kworker/5:3 Tainted: G B 4.4.52 #480
Hardware name: Google Kevin (DT)
Workqueue: events driver_set_config_work
task: ffffffc0c3690000 ti: ffffffc0ae9a8000 task.ti: ffffffc0ae9a8000
PC is at hub_port_init+0xc3c/0xd10
LR is at hub_port_init+0xc3c/0xd10
...
Call trace:
[<ffffffc0007fbbfc>] hub_port_init+0xc3c/0xd10
[<ffffffc0007fbe2c>] usb_reset_and_verify_device+0x15c/0x82c
[<ffffffc0007fc5e0>] usb_reset_device+0xe4/0x298
[<ffffffbffc0e3fcc>] rtl8152_probe+0x84/0x9b0 [r8152]
[<ffffffc00080ca8c>] usb_probe_interface+0x244/0x2f8
[<ffffffc000774a24>] driver_probe_device+0x180/0x3b4
[<ffffffc000774e48>] __device_attach_driver+0xb4/0xe0
[<ffffffc000772168>] bus_for_each_drv+0xb4/0xe4
[<ffffffc0007747ec>] __device_attach+0xd0/0x158
[<ffffffc000775080>] device_initial_probe+0x24/0x30
[<ffffffc0007739d4>] bus_probe_device+0x50/0xe4
[<ffffffc000770bd0>] device_add+0x414/0x738
[<ffffffc000809fe8>] usb_set_configuration+0x89c/0x914
[<ffffffc00080a120>] driver_set_config_work+0xc0/0xf0
[<ffffffc000249bb8>] process_one_work+0x390/0x6b8
[<ffffffc00024abcc>] worker_thread+0x480/0x610
[<ffffffc000251a80>] kthread+0x164/0x178
[<ffffffc0002045d0>] ret_from_fork+0x10/0x40
Since we don't know anything about LPM capabilities without BOS descriptor,
don't attempt to enable LPM if it is not available.
Fixes: 890dae8867 ("xhci: Enable LPM support only for hardwired ...")
Cc: stable <stable@vger.kernel.org>
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_PM=n:
drivers/usb/core/hub.c:107: warning: ‘hub_usb3_port_prepare_disable’ declared inline after being called
drivers/usb/core/hub.c:107: warning: previous declaration of ‘hub_usb3_port_prepare_disable’ was here
To fix this, move hub_port_disable() after
hub_usb3_port_prepare_disable(), and adjust forward declarations.
Fixes: 37be66767e ("usb: hub: Fix auto-remount of safely removed or ejected USB-3 devices")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On a system with a defective USB device connected to an USB hub,
an endless sequence of port connect events was observed. The sequence
of events as observed is as follows:
- Port reports connected event (port status=USB_PORT_STAT_CONNECTION).
- Event handler debounces port and resets it by calling hub_port_reset().
- hub_port_reset() calls hub_port_wait_reset() to wait for the reset
to complete.
- The reset completes, but USB_PORT_STAT_CONNECTION is not immediately
set in the port status register.
- hub_port_wait_reset() returns -ENOTCONN.
- Port initialization sequence is aborted.
- A few milliseconds later, the port again reports a connected event,
and the sequence repeats.
This continues either forever or, randomly, stops if the connection
is already re-established when the port status is read. It results in
a high rate of udev events. This in turn destabilizes userspace since
the above sequence holds the device mutex pretty much continuously
and prevents userspace from actually reading the device status.
To prevent the problem from happening, let's wait for the connection
to be re-established after a port reset. If the device was actually
disconnected, the code will still return an error, but it will do so
only after the long reset timeout.
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB-3 does not have any link state that will avoid negotiating a connection
with a plugged-in cable but will signal the host when the cable is
unplugged.
For USB-3 we used to first set the link to Disabled, then to RxDdetect to
be able to detect cable connects or disconnects. But in RxDetect the
connected device is detected again and eventually enabled.
Instead set the link into U3 and disable remote wakeups for the device.
This is what Windows does, and what Alan Stern suggested.
Cc: stable@vger.kernel.org
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of the USB core files were missing explicit license information.
As all files in the kernel tree are implicitly licensed under the
GPLv2-only, be explicit in case someone get confused looking at
individual files by using the SPDX nomenclature.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
