commit 2419f30a4a upstream.
As commented in the struct's definition there shouldn't be anything
underneath its 'priv[0]' member as it would break some macros.
The patch converts the broken_suspend into a bit-field and relocates it
next to to the rest of bit-fields.
Fixes: a7d57abcc8 ("xhci: workaround CSS timeout on AMD SNPS 3.0 xHC")
Reported-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45f750c16c upstream.
The code to prevent a bus suspend if a USB3 port was still in link training
also reacted to USB2 port polling state.
This caused bus suspend to busyloop in some cases.
USB2 polling state is different from USB3, and should not prevent bus
suspend.
Limit the USB3 link training state check to USB3 root hub ports only.
The origial commit went to stable so this need to be applied there as well
Fixes: 2f31a67f01 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c9287fa657 ]
list_for_each_entry_safe() is not safe for deleting entries from the
list if the spin lock, which protects it, is released and reacquired during
the list iteration. Fix this issue by replacing this construction with
a simple check if list is empty and removing the first entry in each
iteration. This is almost equivalent to a revert of the commit mentioned in
the Fixes: tag.
This patch fixes following issue:
--->8---
Unable to handle kernel NULL pointer dereference at virtual address 00000104
pgd = (ptrval)
[00000104] *pgd=00000000
Internal error: Oops: 817 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 1 PID: 84 Comm: kworker/1:1 Not tainted 4.20.0-rc2-next-20181114-00009-g8266b35ec404 #1061
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
Workqueue: events eth_work
PC is at rx_fill+0x60/0xac
LR is at _raw_spin_lock_irqsave+0x50/0x5c
pc : [<c065fee0>] lr : [<c0a056b8>] psr: 80000093
sp : ee7fbee8 ip : 00000100 fp : 00000000
r10: 006000c0 r9 : c10b0ab0 r8 : ee7eb5c0
r7 : ee7eb614 r6 : ee7eb5ec r5 : 000000dc r4 : ee12ac00
r3 : ee12ac24 r2 : 00000200 r1 : 60000013 r0 : ee7eb5ec
Flags: Nzcv IRQs off FIQs on Mode SVC_32 ISA ARM Segment none
Control: 10c5387d Table: 6d5dc04a DAC: 00000051
Process kworker/1:1 (pid: 84, stack limit = 0x(ptrval))
Stack: (0xee7fbee8 to 0xee7fc000)
...
[<c065fee0>] (rx_fill) from [<c0143b7c>] (process_one_work+0x200/0x738)
[<c0143b7c>] (process_one_work) from [<c0144118>] (worker_thread+0x2c/0x4c8)
[<c0144118>] (worker_thread) from [<c014a8a4>] (kthread+0x128/0x164)
[<c014a8a4>] (kthread) from [<c01010b4>] (ret_from_fork+0x14/0x20)
Exception stack(0xee7fbfb0 to 0xee7fbff8)
...
---[ end trace 64480bc835eba7d6 ]---
Fixes: fea14e68ff ("usb: gadget: u_ether: use better list accessors")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 069caf5950 ]
Commit 387f869d25 ("usb: gadget: u_ether: conditionally align
transfer size") started aligning transfer size only if requested,
breaking omap_udc DMA mode. Set quirk_ep_out_aligned_size to restore
the old behaviour.
Fixes: 387f869d25 ("usb: gadget: u_ether: conditionally align transfer size")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c2322fbca ]
On Palm TE nothing happens when you try to use gadget drivers and plug
the USB cable. Fix by adding the board to the vbus sense quirk list.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ca6695f57 ]
On OMAP 15xx machines there are no transceivers, and omap_udc_start()
always fails as it forgot to adjust the default return value.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99f700366f ]
We currently crash if usb_add_gadget_udc_release() fails, since the
udc->done is not initialized until in the remove function.
Furthermore, on module removal the udc data is accessed although
the release function is already triggered by usb_del_gadget_udc()
early in the function.
Fix by rewriting the release and remove functions, basically moving
all the cleanup into the release function, and doing the completion
only in the module removal case.
The patch fixes omap_udc module probe with a failing gadged, and also
allows the removal of omap_udc. Tested by running "modprobe omap_udc;
modprobe -r omap_udc" in a loop.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 286afdde16 ]
The current code fails to release the third irq on the error path
(observed by reading the code), and we get also multiple WARNs with
failing gadget drivers due to duplicate IRQ releases. Fix by using
devm_request_irq().
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0472bf06c6 upstream.
Don't allow USB3 U1 or U2 if the latency to wake up from the U-state
reaches the service interval for a periodic endpoint.
This is according to xhci 1.1 specification section 4.23.5.2 extra note:
"Software shall ensure that a device is prevented from entering a U-state
where its worst case exit latency approaches the ESIT."
Allowing too long exit latencies for periodic endpoint confuses xHC
internal scheduling, and new devices may fail to enumerate with a
"Not enough bandwidth for new device state" error from the host.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a7d57abcc8 upstream.
Occasionally AMD SNPS 3.0 xHC does not respond to
CSS when set, also it does not flag anything on SRE and HCE
to point the internal xHC errors on USBSTS register. This stalls
the entire system wide suspend and there is no point in stalling
just because of xHC CSS is not responding.
To work around this problem, if the xHC does not flag
anything on SRE and HCE, we can skip the CSS
timeout and allow the system to continue the suspend. Once the
system resume happens we can internally reset the controller
using XHCI_RESET_ON_RESUME quirk
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com>
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Cc: <stable@vger.kernel.org>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f51ccf4621 upstream.
The USB-serial console implementation has never reported the actual
terminal settings used. Despite storing the corresponding cflags in its
struct console, these were never honoured on later tty open() where the
tty termios would be left initialised to the driver defaults.
Unlike the serial console implementation, the USB-serial code calls
subdriver open() already at console setup. While calling set_termios()
and write() before open() looks like it could work for some USB-serial
drivers, others definitely do not expect this, so modelling this after
serial core is going to be intrusive, if at all possible.
Instead, use a (renamed) tty helper to save the termios data used at
console setup so that the tty termios reflects the actual terminal
settings after a subsequent tty open().
Note that the calls to tty_init_termios() (tty_driver_install()) and
tty_save_termios() are serialised using the disconnect mutex.
This specifically fixes a regression that was triggered by a recent
change adding software flow control to the pl2303 driver: a getty trying
to disable flow control while leaving the baud rate unchanged would now
also set the baud rate to the driver default (prior to the flow-control
change this had been a noop).
Fixes: 7041d9c3f0 ("USB: serial: pl2303: add support for tx xon/xoff flow control")
Cc: stable <stable@vger.kernel.org> # 4.18
Cc: Florian Zumbiehl <florz@florz.de>
Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f2dde6ba8 upstream.
Some lower volume SanDisk Ultra Flair in 16GB, which the VID:PID is
in 0781:5591, will aggressively request LPM of U1/U2 during runtime,
when using this thumb drive as the OS installation key we found the
device will generate failure during U1 exit path making it dropped
from the USB bus, this causes a corrupted installation in system at
the end.
i.e.,
[ 166.918296] hub 2-0:1.0: state 7 ports 7 chg 0000 evt 0004
[ 166.918327] usb usb2-port2: link state change
[ 166.918337] usb usb2-port2: do warm reset
[ 166.970039] usb usb2-port2: not warm reset yet, waiting 50ms
[ 167.022040] usb usb2-port2: not warm reset yet, waiting 200ms
[ 167.276043] usb usb2-port2: status 02c0, change 0041, 5.0 Gb/s
[ 167.276050] usb 2-2: USB disconnect, device number 2
[ 167.276058] usb 2-2: unregistering device
[ 167.276060] usb 2-2: unregistering interface 2-2:1.0
[ 167.276170] xhci_hcd 0000:00:15.0: shutdown urb ffffa3c7cc695cc0 ep1in-bulk
[ 167.284055] sd 0:0:0:0: [sda] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ 167.284064] sd 0:0:0:0: [sda] tag#0 CDB: Read(10) 28 00 00 33 04 90 00 01 00 00
...
Analyzed the USB trace in the link layer we realized it is because
of the 6-ms timer of tRecoveryConfigurationTimeout which documented
on the USB 3.2 Revision 1.0, the section 7.5.10.4.2 of "Exit from
Recovery.Configuration"; device initiates U1 exit -> Recovery.Active
-> Recovery.Configuration, then the host timer timeout makes the link
transits to eSS.Inactive -> Rx.Detect follows by a Warm Reset.
Interestingly, the other higher volume of SanDisk Ultra Flair sharing
the same VID:PID, such as 64GB, would not request LPM during runtime,
it sticks at U0 always, thus disabling LPM does not affect those thumb
drives at all.
The same odd occures in SanDisk Ultra Fit 16GB, VID:PID in 0781:5583.
Signed-off-by: Harry Pan <harry.pan@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit effd14f66c upstream.
Cherry G230 Stream 2.0 (G85-231) and 3.0 (G85-232) need this quirk to
function correctly. This fixes a but where double pressing numlock locks
up the device completely with need to replug the keyboard.
Signed-off-by: Michael Niewöhner <linux@mniewoehner.de>
Tested-by: Michael Niewöhner <linux@mniewoehner.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f31a67f01 upstream.
USB3 roothub might autosuspend before a plugged USB3 device is detected,
causing USB3 device enumeration failure.
USB3 devices don't show up as connected and enabled until USB3 link trainig
completes. On a fast booting platform with a slow USB3 link training the
link might reach the connected enabled state just as the bus is suspending.
If this device is discovered first time by the xhci_bus_suspend() routine
it will be put to U3 suspended state like the other ports which failed to
suspend earlier.
The hub thread will notice the connect change and resume the bus,
moving the port back to U0
This U0 -> U3 -> U0 transition right after being connected seems to be
too much for some devices, causing them to first go to SS.Inactive state,
and finally end up stuck in a polling state with reset asserted
Fix this by failing the bus suspend if a port has a connect change or is
in a polling state in xhci_bus_suspend().
Don't do any port changes until all ports are checked, buffer all port
changes and only write them in the end if suspend can proceed
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 11644a7659 upstream.
Implement workaround for ThunderX2 Errata-129 (documented in
CN99XX Known Issues" available at Cavium support site).
As per ThunderX2errata-129, USB 2 device may come up as USB 1
if a connection to a USB 1 device is followed by another connection to
a USB 2 device, the link will come up as USB 1 for the USB 2 device.
Resolution: Reset the PHY after the USB 1 device is disconnected.
The PHY reset sequence is done using private registers in XHCI register
space. After the PHY is reset we check for the PLL lock status and retry
the operation if it fails. From our tests, retrying 4 times is sufficient.
Add a new quirk flag XHCI_RESET_PLL_ON_DISCONNECT to invoke the workaround
in handle_xhci_port_status().
Cc: stable@vger.kernel.org
Signed-off-by: George Cherian <george.cherian@cavium.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5baeaeabc upstream.
This definition is used by msecs_to_jiffies in milliseconds.
According to the comments, max rexit timeout should be 20ms.
Align with the comments to properly calculate the delay.
Verified on Sunrise Point-LP and Cannon Lake.
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 958c0bd860 upstream.
Realtek USB3.0 Card Reader [0bda:0328] reports wrong port status on
Cannon lake PCH USB3.1 xHCI [8086:a36d] after resume from S3,
after clear port reset it works fine.
Since this device is registered on USB3 roothub at boot,
when port status reports not superspeed, xhci_get_port_status will call
an uninitialized completion in bus_state[0].
Kernel will hang because of NULL pointer.
Restrict the USB2 resume status check in USB2 roothub to fix hang issue.
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1245374e9b upstream.
At xhci removal the USB3 hcd (shared_hcd) is removed before the primary
USB2 hcd. Interrupts for port status changes may still occur for USB3
ports after the shared_hcd is freed, causing NULL pointer dereference.
Check if xhci->shared_hcd is still valid before handing USB3 port events
Cc: <stable@vger.kernel.org>
Reported-by: Peter Chen <peter.chen@nxp.com>
Tested-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f068090426 upstream.
Ensure that the shared_hcd pointer is valid when calling usb_put_hcd()
The shared_hcd is removed and freed in xhci by first calling
usb_remove_hcd(xhci->shared_hcd), and later
usb_put_hcd(xhci->shared_hcd)
Afer commit fe190ed0d6 ("xhci: Do not halt the host until both HCD have
disconnected their devices.") the shared_hcd was never properly put as
xhci->shared_hcd was set to NULL before usb_put_hcd(xhci->shared_hcd) was
called.
shared_hcd (USB3) is removed before primary hcd (USB2).
While removing the primary hcd we might need to handle xhci interrupts
to cleanly remove last USB2 devices, therefore we need to set
xhci->shared_hcd to NULL before removing the primary hcd to let xhci
interrupt handler know shared_hcd is no longer available.
xhci-plat.c, xhci-histb.c and xhci-mtk first create both their hcd's before
adding them. so to keep the correct reverse removal order use a temporary
shared_hcd variable for them.
For more details see commit 4ac53087d6 ("usb: xhci: plat: Create both
HCDs before adding them")
Fixes: fe190ed0d6 ("xhci: Do not halt the host until both HCD have disconnected their devices.")
Cc: Joel Stanley <joel@jms.id.au>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Jianguo Sun <sunjianguo1@huawei.com>
Cc: <stable@vger.kernel.org>
Reported-by: Jack Pham <jackp@codeaurora.org>
Tested-by: Jack Pham <jackp@codeaurora.org>
Tested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b412b04a0 upstream.
In dwc3_pci_quirks() function, gpiod lookup table is only registered for
baytrail SOC. But in dwc3_pci_remove(), we try to unregistered it
without any checks. This leads to NULL pointer de-reference exception in
gpiod_remove_lookup_table() when unloading the module for non baytrail
SOCs. This patch fixes this issue.
Fixes: 5741022cbd ("usb: dwc3: pci: Add GPIO lookup table on platforms
without ACPI GPIO resources")
Cc: <stable@vger.kernel.org>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08fd9a82fd upstream.
If dwc3_core_init_mode() fails with deferred probe,
next probe fails on sysfs with
sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:11.0/dwc3.0.auto/dwc3.0.auto.ulpi'
To avoid this failure, clean up ULPI device.
Cc: <stable@vger.kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba3a51ac32 upstream.
Current check for the last extra TRB for zero and unaligned transfers
does not account for isoc OUT. The last TRB of the Buffer Descriptor for
isoc OUT transfers will be retired with HWO=0. As a result, we won't
return early. The req->remaining will be updated to include the BUFSIZ
count of the extra TRB, and the actual number of transferred bytes
calculation will be wrong.
To fix this, check whether it's a short or zero packet and the last TRB
chain bit to return early.
Fixes: c6267a5163 ("usb: dwc3: gadget: align transfers to wMaxPacketSize")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2fc6d4be35 upstream.
When chaining ISOC TRBs together, only the first ISOC TRB should be of
type ISOC_FIRST, all others should be of type ISOC. This patch fixes
that.
Fixes: c6267a5163 ("usb: dwc3: gadget: align transfers to wMaxPacketSize")
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22454b79e6 upstream.
This will clear the USB_PORT_FEAT_C_CONNECTION bit in case of a hub port reset
only if a device is was attached to the hub port before resetting the hub port.
Using a Lenovo T480s attached to the ultra dock it was not possible to detect
some usb-c devices at the dock usb-c ports because the hub_port_reset code
will clear the USB_PORT_FEAT_C_CONNECTION bit after the actual hub port reset.
Using this device combo the USB_PORT_FEAT_C_CONNECTION bit was set between the
actual hub port reset and the clear of the USB_PORT_FEAT_C_CONNECTION bit.
This ends up with clearing the USB_PORT_FEAT_C_CONNECTION bit after the
new device was attached such that it was not detected.
This patch will not clear the USB_PORT_FEAT_C_CONNECTION bit if there is
currently no device attached to the port before the hub port reset.
This will avoid clearing the connection bit for new attached devices.
Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a771125776 upstream.
Following on from this patch: https://lkml.org/lkml/2017/11/3/516,
Corsair K70 LUX RGB keyboards also require the DELAY_INIT quirk to
start correctly at boot.
Dmesg output:
usb 1-6: string descriptor 0 read error: -110
usb 1-6: New USB device found, idVendor=1b1c, idProduct=1b33
usb 1-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-6: can't set config #1, error -110
Signed-off-by: Emmanuel Pescosta <emmanuelpescosta099@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 781f0766cc upstream.
Devices connected under Terminus Technology Inc. Hub (1a40:0101) may
fail to work after the system resumes from suspend:
[ 206.063325] usb 3-2.4: reset full-speed USB device number 4 using xhci_hcd
[ 206.143691] usb 3-2.4: device descriptor read/64, error -32
[ 206.351671] usb 3-2.4: device descriptor read/64, error -32
Info for this hub:
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=480 MxCh= 4
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1a40 ProdID=0101 Rev=01.11
S: Product=USB 2.0 Hub
C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
Some expirements indicate that the USB devices connected to the hub are
innocent, it's the hub itself is to blame. The hub needs extra delay
time after it resets its port.
Hence wait for extra delay, if the device is connected to this quirky
hub.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit deefd24228 upstream.
Raydium USB touchscreen fails to set config if LPM is enabled:
[ 2.030658] usb 1-8: New USB device found, idVendor=2386, idProduct=3119
[ 2.030659] usb 1-8: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.030660] usb 1-8: Product: Raydium Touch System
[ 2.030661] usb 1-8: Manufacturer: Raydium Corporation
[ 7.132209] usb 1-8: can't set config #1, error -110
Same behavior can be observed on 2386:3114.
Raydium claims the touchscreen supports LPM under Windows, so I used
Microsoft USB Test Tools (MUTT) [1] to check its LPM status. MUTT shows
that the LPM doesn't work under Windows, either. So let's just disable LPM
for Raydium touchscreens.
[1] https://docs.microsoft.com/en-us/windows-hardware/drivers/usbcon/usb-test-tools
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63529eaa61 upstream.
The cdc-acm kernel module currently does not support the Hiro (Conexant)
H05228 USB modem. The patch below adds the device specific information:
idVendor 0x0572
idProduct 0x1349
Signed-off-by: Maarten Jacobs <maarten256@outlook.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit afc92514a3 upstream.
If the "workaround_for_vbus" is true, the driver will not call
usb_disconnect(). So, since the controller keeps some registers'
value, the driver doesn't re-enumarate suitable speed after
the b-device mode is disabled. To fix the issue, this patch
adds usb_disconnect() calling in renesas_usb3_b_device_write()
if workaround_for_vbus is true.
Fixes: 43ba968b00 ("usb: gadget: udc: renesas_usb3: add debugfs to set the b-device mode")
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b6af2f58c upstream.
Current code mistakenly checks against max current to determine
order but this should be max voltage. This commit fixes the issue
so order is correctly determined, thus avoiding failure based on
a higher voltage PPS APDO having a lower maximum current output,
which is actually valid.
Fixes: 2eadc33f40 ("typec: tcpm: Add core support for sink side PPS")
Cc: <stable@vger.kernel.org>
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e28fd56ad5 upstream.
In rmmod path, usbip_vudc does platform_device_put() twice once from
platform_device_unregister() and then from put_vudc_device().
The second put results in:
BUG kmalloc-2048 (Not tainted): Poison overwritten error or
BUG: KASAN: use-after-free in kobject_put+0x1e/0x230 if KASAN is
enabled.
[ 169.042156] calling init+0x0/0x1000 [usbip_vudc] @ 1697
[ 169.042396] =============================================================================
[ 169.043678] probe of usbip-vudc.0 returned 1 after 350 usecs
[ 169.044508] BUG kmalloc-2048 (Not tainted): Poison overwritten
[ 169.044509] -----------------------------------------------------------------------------
...
[ 169.057849] INFO: Freed in device_release+0x2b/0x80 age=4223 cpu=3 pid=1693
[ 169.057852] kobject_put+0x86/0x1b0
[ 169.057853] 0xffffffffc0c30a96
[ 169.057855] __x64_sys_delete_module+0x157/0x240
Fix it to call platform_device_del() instead and let put_vudc_device() do
the platform_device_put().
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8b97d73c4d ]
The ChipIdea IRQ is disabled before scheduling the otg work and
re-enabled on otg work completion. However if the job is already
scheduled we have to undo the effect of disable_irq int order to
balance the IRQ disable-depth value.
Fixes: be6b0c1bd0 ("usb: chipidea: using one inline function to cover queue work operations")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 330e2d61cd ]
When USB bus host controller root hub resumes from autosuspend,
it immediately tries to enter auto-suspend, but there can be a
scenario when root hub is resuming its usb2 ports, in that particular
case USB host controller auto suspend fails since it is busy
to resuming its usb2 ports.
This makes multiple failed cycles of auto-suspend until all usb2
ports of host controller root hub do not resume.
This patch uses USB core framework usb_hcd_start_port_resume,
usb_hcd_end_port_resume API's in order to autoresume/autosuspend
root hub properly.
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 554fab6dbf ]
Currently when requesting a specific voltage or current through
the psy interface, for PPS, when reading back from that interface
the values will always be the same as previously given, if the
request was successful. However PPS only allows for 20mV voltage
steps and 50mA current steps, and the psy class expects microvolt
and micro amp requests, so inbetween values can be provided through
this interface. Really when reading back the true values negotiated
should be given, and not the ones originally asked for.
To report the actual values negotiated with the Source, the values
stored are now rounded down to the relevant step units prior to
building the PPS request, so that those values are later correctly
reported through the psy interface. In addition this improves the
adjustments made to meet the operating power requirements of the
platform, which previously could have been slightly out due to not
using valid PPS units of voltage and current.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
