[ Upstream commit 5fc453d7de ]
GISB bus error kernel panics have been observed during S2 transition
tests on the 7271t platform. The errors are a result of the BDC
interrupt handler trying to access BDC register space after the
system's suspend callbacks have completed.
Adding a suspend hook to the BDC driver that halts the controller before
S2 entry thus preventing unwanted access to the BDC register space during
this transition.
Signed-off-by: Danesh Petigara <danesh.petigara@broadcom.com>
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a95bdfd220 ]
Multiple connects/disconnects can cause a crash on the second
disconnect. The driver had a problem where it would try to send
endpoint commands after it was disconnected which is not allowed
by the hardware. The fix is to only allow the endpoint commands
when the endpoint is connected. This will also fix issues that
showed up when using configfs to create gadgets.
Signed-off-by: Sasi Kumar <sasi.kumar@broadcom.com>
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2468c877da ]
Driver does not release memory for device on error handling paths in
net2280_probe() when gadget_release() is not registered yet.
The patch fixes the bug like in other similar drivers.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 17a8271658 upstream.
In previous patches that added support for new iowarrior devices, the
handling of the report size was not done correct.
Fix that up and update the copyright date for the driver
Reworked from an original patch written by Christoph Jung.
Fixes: bab5417f5f ("USB: misc: iowarrior: add support for the 100 device")
Fixes: 5f6f8da2d7 ("USB: misc: iowarrior: add support for the 28 and 28L devices")
Fixes: 461d8deb26 ("USB: misc: iowarrior: add support for 2 OEMed devices")
Cc: stable <stable@kernel.org>
Reported-by: Christoph Jung <jung@codemercs.com>
Link: https://lore.kernel.org/r/20200726094939.1268978-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d2a4309c1a upstream.
When running qmi-firmware-update on the Sierra Wireless EM7305 in a Toshiba
laptop, it changed product ID to 0x9062 when entering QDL mode:
usb 2-4: new high-speed USB device number 78 using xhci_hcd
usb 2-4: New USB device found, idVendor=1199, idProduct=9062, bcdDevice= 0.00
usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-4: Product: EM7305
usb 2-4: Manufacturer: Sierra Wireless, Incorporated
The upgrade could complete after running
# echo 1199 9062 > /sys/bus/usb-serial/drivers/qcserial/new_id
qcserial 2-4:1.0: Qualcomm USB modem converter detected
usb 2-4: Qualcomm USB modem converter now attached to ttyUSB0
Signed-off-by: Erik Ekman <erik@kryo.se>
Link: https://lore.kernel.org/r/20200717185118.3640219-1-erik@kryo.se
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 5c4e8d3781 ("usb: host: xhci-tegra: Add support for XUSB
context save/restore") is using the IPFS 'num_offsets' value when
allocating memory for FPCI context instead of the FPCI 'num_offsets'.
After commit cad064f1bd ("devres: handle zero size in devm_kmalloc()")
was added system suspend started failing on Tegra186. The kernel log
showed that the Tegra XHCI driver was crashing on entry to suspend when
attempting the save the USB context. On Tegra186, the IPFS context has a
zero length but the FPCI content has a non-zero length, and because of
the bug in the Tegra XHCI driver we are incorrectly allocating a zero
length array for the FPCI context. The crash seen on entering suspend
when we attempt to save the FPCI context and following commit
cad064f1bd ("devres: handle zero size in devm_kmalloc()") this now
causes a NULL pointer deference when we access the memory. Fix this by
correcting the amount of memory we are allocating for FPCI contexts.
Cc: stable@vger.kernel.org
Fixes: 5c4e8d3781 ("usb: host: xhci-tegra: Add support for XUSB context save/restore")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200715113842.30680-1-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver would happily overwrite its write buffer with user data in
256 byte increments due to a removed buffer-space sanity check.
Fixes: 5fcf62b0f1 ("tty: iuu_phoenix: fix locking.")
Cc: stable <stable@vger.kernel.org> # 2.6.31
Signed-off-by: Johan Hovold <johan@kernel.org>
Felipe writes:
USB: fixes for v5.8-rc3
Adding support for recent Intel devices (Tiger Lake and Jasper Lake)
on dwc3. We have some endianess fixes in cdns3, a memleak fix in
gr_udc and lock API usage fix in the legacy f_uac1
Signed-off-by: Felipe Balbi <balbi@kernel.org>
* tag 'fixes-for-v5.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
usb: gadget: function: fix missing spinlock in f_uac1_legacy
usb: gadget: udc: atmel: fix uninitialized read in debug printk
usb: gadget: udc: atmel: remove outdated comment in usba_ep_disable()
usb: dwc2: Fix shutdown callback in platform
usb: cdns3: trace: fix some endian issues
usb: cdns3: ep0: fix some endian issues
usb: gadget: udc: gr_udc: fix memleak on error handling path in gr_ep_init()
usb: gadget: fix langid kernel-doc warning in usbstring.c
usb: dwc3: pci: add support for the Intel Jasper Lake
usb: dwc3: pci: add support for the Intel Tiger Lake PCH -H variant
clang static analysis flags this error
c67x00-sched.c:489:55: warning: Use of memory after it is freed [unix.Malloc]
usb_hcd_giveback_urb(c67x00_hcd_to_hcd(c67x00), urb, urbp->status);
^~~~~~~~~~~~
Problem happens in this block of code
c67x00_release_urb(c67x00, urb);
usb_hcd_unlink_urb_from_ep(c67x00_hcd_to_hcd(c67x00), urb);
spin_unlock(&c67x00->lock);
usb_hcd_giveback_urb(c67x00_hcd_to_hcd(c67x00), urb, urbp->status);
In the call to c67x00_release_urb has this freeing of urbp
urbp = urb->hcpriv;
urb->hcpriv = NULL;
list_del(&urbp->hep_node);
kfree(urbp);
And so urbp is freed before usb_hcd_giveback_urb uses it as its 3rd
parameter.
Since all is required is the status, pass the status directly as is
done in c64x00_urb_dequeue
Fixes: e9b29ffc51 ("USB: add Cypress c67x00 OTG controller HCD driver")
Signed-off-by: Tom Rix <trix@redhat.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200708131243.24336-1-trix@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a missing spinlock protection for play_queue, because
the play_queue may be destroyed when the "playback_work"
work func and "f_audio_out_ep_complete" callback func
operate this paly_queue at the same time.
Fixes: c6994e6f06 ("USB: gadget: add USB Audio Gadget driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Zhang Qiang <qiang.zhang@windriver.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fixed commit moved the assignment of 'req', but did not update a
reference in the DBG() call. Use the argument as it was renamed.
Fixes: 5fb694f96e ("usb: gadget: udc: atmel: fix possible oops when unloading module")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fixed commit removed the offending behaviour from the driver, but missed
the comment and associated test. Remove them now.
Fixes: 38e58986e6 ("usb: gadget: udc: atmel: don't disable enpdoints we don't own")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
To avoid lot of interrupts from dwc2 core, which can be asserted in
specific conditions need to disable interrupts on HW level instead of
disable IRQs on Kernel level, because of IRQ can be shared between
drivers.
Cc: stable@vger.kernel.org
Fixes: a40a00318c ("usb: dwc2: add shutdown callback to platform variant")
Tested-by: Frank Mori Hess <fmh6jj@gmail.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Frank Mori Hess <fmh6jj@gmail.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
gr_ep_init() does not assign the allocated request anywhere if allocation
of memory for the buffer fails. This is a memory leak fixed by the given
patch.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fix spelling of the 'langid' function argument in the kernel-doc
notation to quieten a kernel-doc warning.
../drivers/usb/gadget/usbstring.c:77: warning: Function parameter or member 'langid' not described in 'usb_validate_langid'
../drivers/usb/gadget/usbstring.c:77: warning: Excess function parameter 'lang' description in 'usb_validate_langid'
Fixes: 17309a6a43 ("usb: gadget: add "usb_validate_langid" function")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Tao Ren <rentao.bupt@gmail.com>
Cc: Tao Ren <rentao.bupt@gmail.com>
Cc: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Johan writes:
USB-serial fixes for 5.8-rc5
Here are some new device ids for 5.8.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.8-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Quectel EG95 LTE modem
USB: serial: ch341: add new Product ID for CH340
USB: serial: option: add GosunCn GM500 series
USB: serial: cypress_m8: enable Simply Automated UPB PIM
Pull USB fixes from Greg KH:
"Here are some small USB fixes for 5.8-rc3 to resolve some reported
issues.
Nothing major here:
- gadget driver fixes
- cdns3 driver fixes
- xhci fixes
- renesas_usbhs driver fixes
- some new device support with ids
- documentation update
All of these have been in linux-next with no reported issues"
* tag 'usb-5.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (27 commits)
usb: renesas_usbhs: getting residue from callback_result
Revert "usb: dwc3: exynos: Add support for Exynos5422 suspend clk"
xhci: Poll for U0 after disabling USB2 LPM
xhci: Return if xHCI doesn't support LPM
usb: host: xhci-mtk: avoid runtime suspend when removing hcd
xhci: Fix enumeration issue when setting max packet size for FS devices.
xhci: Fix incorrect EP_STATE_MASK
usb: cdns3: ep0: add spinlock for cdns3_check_new_setup
usb: cdns3: trace: using correct dir value
usb: cdns3: ep0: fix the test mode set incorrectly
Revert "usb: dwc3: exynos: Add support for Exynos5422 suspend clk"
usb: gadget: udc: Potential Oops in error handling code
usb: phy: tegra: Fix unnecessary check in tegra_usb_phy_probe()
usb: dwc3: pci: Fix reference count leak in dwc3_pci_resume_work
usb: cdns3: ep0: add spinlock for cdns3_check_new_setup
usb: cdns3: trace: using correct dir value
usb: cdns3: ep0: fix the test mode set incorrectly
usb: typec: tcpci_rt1711h: avoid screaming irq causing boot hangs
USB: ohci-sm501: Add missed iounmap() in remove
cdc-acm: Add DISABLE_ECHO quirk for Microchip/SMSC chip
...
Felipe writes:
usb: fixes for v5.8-rc2
A revert of Exynos5422 suspend clock support, it turns out it wasn't
ready to be merged. CDNS3 got a fix for test mode initialization.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
* tag 'fixes-for-v5.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
Revert "usb: dwc3: exynos: Add support for Exynos5422 suspend clk"
usb: gadget: udc: Potential Oops in error handling code
usb: phy: tegra: Fix unnecessary check in tegra_usb_phy_probe()
usb: dwc3: pci: Fix reference count leak in dwc3_pci_resume_work
usb: cdns3: ep0: add spinlock for cdns3_check_new_setup
usb: cdns3: trace: using correct dir value
usb: cdns3: ep0: fix the test mode set incorrectly
In kgdb context, calling console handlers aren't safe due to locks used
in those handlers which could in turn lead to a deadlock. Although, using
oops_in_progress increases the chance to bypass locks in most console
handlers but it might not be sufficient enough in case a console uses
more locks (VT/TTY is good example).
Currently when a driver provides both polling I/O and a console then kdb
will output using the console. We can increase robustness by using the
currently active polling I/O driver (which should be lockless) instead
of the corresponding console. For several common cases (e.g. an
embedded system with a single serial port that is used both for console
output and debugger I/O) this will result in no console handler being
used.
In order to achieve this we need to reverse the order of preference to
use dbg_io_ops (uses polling I/O mode) over console APIs. So we just
store "struct console" that represents debugger I/O in dbg_io_ops and
while emitting kdb messages, skip console that matches dbg_io_ops
console in order to avoid duplicate messages. After this change,
"is_console" param becomes redundant and hence removed.
Suggested-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/1591264879-25920-5-git-send-email-sumit.garg@linaro.org
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
This driver assumed that dmaengine_tx_status() could return
the residue even if the transfer was completed. However,
this was not correct usage [1] and this caused to break getting
the residue after the commit 24461d9792 ("dmaengine:
virt-dma: Fix access after free in vchan_complete()") actually.
So, this is possible to get wrong received size if the usb
controller gets a short packet. For example, g_zero driver
causes "bad OUT byte" errors.
The usb-dmac driver will support the callback_result, so this
driver can use it to get residue correctly. Note that even if
the usb-dmac driver has not supported the callback_result yet,
this patch doesn't cause any side-effects.
[1]
https://lore.kernel.org/dmaengine/20200616165550.GP2324254@vkoul-mobl/
Reported-by: Hien Dang <hien.dang.eb@renesas.com>
Fixes: 24461d9792 ("dmaengine: virt-dma: Fix access after free in vchan_complete()")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1592482277-19563-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB2 devices with LPM enabled may interrupt the system suspend:
[ 932.510475] usb 1-7: usb suspend, wakeup 0
[ 932.510549] hub 1-0:1.0: hub_suspend
[ 932.510581] usb usb1: bus suspend, wakeup 0
[ 932.510590] xhci_hcd 0000:00:14.0: port 9 not suspended
[ 932.510593] xhci_hcd 0000:00:14.0: port 8 not suspended
..
[ 932.520323] xhci_hcd 0000:00:14.0: Port change event, 1-7, id 7, portsc: 0x400e03
..
[ 932.591405] PM: pci_pm_suspend(): hcd_pci_suspend+0x0/0x30 returns -16
[ 932.591414] PM: dpm_run_callback(): pci_pm_suspend+0x0/0x160 returns -16
[ 932.591418] PM: Device 0000:00:14.0 failed to suspend async: error -16
During system suspend, USB core will let HC suspends the device if it
doesn't have remote wakeup enabled and doesn't have any children.
However, from the log above we can see that the usb 1-7 doesn't get bus
suspended due to not in U0. After a while the port finished U2 -> U0
transition, interrupts the suspend process.
The observation is that after disabling LPM, port doesn't transit to U0
immediately and can linger in U2. xHCI spec 4.23.5.2 states that the
maximum exit latency for USB2 LPM should be BESL + 10us. The BESL for
the affected device is advertised as 400us, which is still not enough
based on my testing result.
So let's use the maximum permitted latency, 10000, to poll for U0
status to solve the issue.
Cc: stable@vger.kernel.org
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200624135949.22611-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unable to complete the enumeration of a USB TV Tuner device.
Per XHCI spec (4.6.5), the EP state field of the input context shall
be cleared for a set address command. In the special case of an FS
device that has "MaxPacketSize0 = 8", the Linux XHCI driver does
not do this before evaluating the context. With an XHCI controller
that checks the EP state field for parameter context error this
causes a problem in cases such as the device getting reset again
after enumeration.
When that field is cleared, the problem does not occur.
This was found and fixed by Sasi Kumar.
Cc: stable@vger.kernel.org
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200624135949.22611-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It should use the correct direction value from register, not depends
on previous software setting. It fixed the EP number wrong issue at
trace when the TRBERR interrupt occurs for EP0IN.
When the EP0IN IOC has finished, software prepares the setup packet
request, the expected direction is OUT, but at that time, the TRBERR
for EP0IN may occur since it is DMULT mode, the DMA does not stop
until TRBERR has met.
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200623030918.8409-3-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If this is in "transceiver" mode the the ->qwork isn't required and is
a NULL pointer. This can lead to a NULL dereference when we call
destroy_workqueue(udc->qwork).
Fixes: 3517c31a8e ("usb: gadget: mv_udc: use devm_xxx for probe")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In the function tegra_usb_phy_probe(), if usb_add_phy_dev() failed,
the return value will be given to err, and if usb_add_phy_dev() succeed,
the return value will be zero. Thus it is unnecessary to repeated check
here.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
dwc3_pci_resume_work() calls pm_runtime_get_sync() that increments
the reference counter. In case of failure, decrement the reference
before returning.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The other thread may access other endpoints when the cdns3_check_new_setup
is handling, add spinlock to protect it.
Cc: <stable@vger.kernel.org>
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
It should use the correct direction value from register, not depends
on previous software setting. It fixed the EP number wrong issue at
trace when the TRBERR interrupt occurs for EP0IN.
When the EP0IN IOC has finished, software prepares the setup packet
request, the expected direction is OUT, but at that time, the TRBERR
for EP0IN may occur since it is DMULT mode, the DMA does not stop
until TRBERR has met.
Cc: <stable@vger.kernel.org>
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add PID for CH340 that's found on some ESP8266 dev boards made by
LilyGO. The specific device that contains such serial converter can be
seen here: https://github.com/LilyGO/LILYGO-T-OI.
Apparently, it's a regular CH340, but I've confirmed with others that
also bought this board that the PID found on this device (0x7522)
differs from other devices with the "same" converter (0x7523).
Simply adding its PID to the driver and rebuilding it made it work
as expected.
Signed-off-by: Igor Moura <imphilippini@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
