commit a17b984115 upstream.
Suspending and resuming the system can sometimes cause the out
URB to get hung after a reset_resume. This causes LED setting
and force feedback to break on resume. To avoid this, just drop
the reset_resume callback so the USB core rebinds xpad to the
wireless pads on resume if a reset happened.
A nice side effect of this change is the LED ring on wireless
controllers is now set correctly on system resume.
Cc: stable@vger.kernel.org
Fixes: 4220f7db1e ("Input: xpad - workaround dead irq_out after suspend/ resume")
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Link: https://lore.kernel.org/r/20220818154411.510308-3-rojtberg@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e62563db85 upstream.
Both i.MX6 and i.MX8 reference manuals list 0xBF8 as SNVS_HPVIDR1
(chapters 57.9 and 6.4.5 respectively).
Without this, trying to read the revision number results in 0 on
all revisions, causing the i.MX6 quirk to apply on all platforms,
which in turn causes the driver to synthesise power button release
events instead of passing the real one as they happen even on
platforms like i.MX8 where that's not wanted.
Fixes: 1a26c92071 ("Input: snvs_pwrkey - send key events for i.MX6 S, DL and Q")
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/4599101.ElGaqSPkdT@pliszka
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a6a87c3616 ]
A lot of modern Clevo barebones have touchpad and/or keyboard issues after
suspend fixable with nomux + reset + noloop + nopnp. Luckily, none of them
have an external PS/2 port so this can safely be set for all of them.
I'm not entirely sure if every device listed really needs all four quirks,
but after testing and production use. No negative effects could be
observed when setting all four.
The list is quite massive as neither the TUXEDO nor the Clevo dmi strings
have been very consistent historically. I tried to keep the list as short
as possible without risking on missing an affected device.
This is revision 3. The Clevo N150CU barebone is still removed as it might
have problems with the fix and needs further investigations. The
SchenkerTechnologiesGmbH System-/Board-Vendor string variations are
added. This is now based in the quirk table refactor. This now also
includes the additional noaux flag for the NS7xMU.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220629112725.12922-5-wse@tuxedocomputers.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff946268a0 ]
Merge i8042 quirk tables to reduce code duplication for devices that need
more than one quirk. Before every quirk had its own table with devices
needing that quirk. If a new quirk needed to be added a new table had to
be created. When a device needed multiple quirks, it appeared in multiple
tables. Now only one table called i8042_dmi_quirk_table exists. In it every
device has one entry and required quirks are coded in the .driver_data
field of the struct dmi_system_id used by this table. Multiple quirks for
one device can be applied by bitwise-or of the new SERIO_QUIRK_* defines.
Also align quirkable options with command line parameters and make vendor
wide quirks per device overwriteable on a per device basis. The first match
is honored while following matches are ignored. So when a vendor wide quirk
is defined in the table, a device can inserted before and therefore
ignoring the vendor wide define.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220629112725.12922-3-wse@tuxedocomputers.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2fd46cd3d ]
Unless the controller is not responding at boot or after suspend/resume,
the driver never resets the controller on x86/ACPI platforms. The driver
still requesting the reset pin at probe() though in case it needs it.
Until now the driver has always requested the reset pin with GPIOD_IN
as type. The idea being to put the pin in high-impedance mode to save
power until the driver actually wants to issue a reset.
But this means that just requesting the pin can cause issues, since
requesting it in another mode then GPIOD_ASIS may cause the pinctrl
driver to touch the pin settings. We have already had issues before
due to a bug in the pinctrl-cherryview.c driver which has been fixed in
commit 921daeeca9 ("pinctrl: cherryview: Preserve
CHV_PADCTRL1_INVRXTX_TXDATA flag on GPIOs").
And now it turns out that requesting the reset-pin as GPIOD_IN also stops
the touchscreen from working on the GPD P2 max mini-laptop. The behavior
of putting the pin in high-impedance mode relies on there being some
external pull-up to keep it high and there seems to be no pull-up on the
GPD P2 max, causing things to break.
This commit fixes this by requesting the reset pin as is when using
the x86/ACPI code paths to lookup the GPIOs; and by not dropping it
back into input-mode in case the driver does end up issuing a reset
for error-recovery.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209061
Fixes: a7d4b17166 ("Input: goodix - add support for getting IRQ + reset GPIOs on Cherry Trail devices")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211206091116.44466-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 209bda4741 ]
Refactor reset handling a bit, change the main reset handler
into a new goodix_reset_no_int_sync() helper and add a
goodix_reset() wrapper which calls goodix_int_sync()
separately.
Also push the dev_err() call on reset failure into the
goodix_reset_no_int_sync() and goodix_int_sync() functions,
so that we don't need to have separate dev_err() calls in
all their callers.
This is a preparation patch for adding support for controllers
without flash, which need to have their firmware uploaded and
need some other special handling too.
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210920150643.155872-4-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2233cb7b6 ]
Add a goodix.h header file, and move the register definitions,
and struct declarations there and add prototypes for various
helper functions.
This is a preparation patch for adding support for controllers
without flash, which need to have their firmware uploaded and
need some other special handling too.
Since MAINTAINERS needs updating because of this change anyways,
also add myself as co-maintainer.
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210920150643.155872-3-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ab2e51898 ]
Commit 223f61b8c5 ("Input: soc_button_array - add Lenovo Yoga Tablet2
1051L to the dmi_use_low_level_irq list") added the 1051L to this list
already, but the same problem applies to the 1051F. As there are no
further 1051 variants (just the F/L), we can just DMI match 1051.
Tested on a Lenovo Yoga Tablet2 1051F: Without this patch the
home-button stops working after a wakeup from suspend.
Signed-off-by: Marius Hoch <mail@mariushoch.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220603120246.3065-1-mail@mariushoch.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f76955ab1 ]
The commit 26623eea0d attempted to deal with potential leak of runtime
PM counter when opening the touchscreen device, however it ended up
erroneously dropping the counter in the case of successfully enabling the
device.
Let's address this by using pm_runtime_resume_and_get() and then executing
pm_runtime_put_sync() only when we fail to send "sense on" command to the
device.
Fixes: 26623eea0d ("Input: stmfts - fix reference leak in stmfts_input_open")
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e4920d42ce upstream.
According to Ilitek "231x & ILI251x Programming Guide" Version: 2.30
"2.1. Power Sequence", "T4 Chip Reset and discharge time" is minimum
10ms and "T2 Chip initial time" is maximum 150ms. Adjust the reset
timings such that T4 is 12ms and T2 is 160ms to fit those figures.
This prevents sporadic touch controller start up failures when some
systems with at least ILI251x controller boot, without this patch
the systems sometimes fail to communicate with the touch controller.
Fixes: 201f3c8035 ("Input: ili210x - add reset GPIO support")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20220518204901.93534-1-marex@denx.de
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b188fba75 upstream.
This reverts commit 37ef4c19b4.
The touchpad present in the Dell Precision 7550 and 7750 laptops
reports a HID_DG_BUTTONTYPE of type MT_BUTTONTYPE_CLICKPAD. However,
the device is not a clickpad, it is a touchpad with physical buttons.
In order to fix this issue, a quirk for the device was introduced in
libinput [1] [2] to disable the INPUT_PROP_BUTTONPAD property:
[Precision 7x50 Touchpad]
MatchBus=i2c
MatchUdevType=touchpad
MatchDMIModalias=dmi:*svnDellInc.:pnPrecision7?50*
AttrInputPropDisable=INPUT_PROP_BUTTONPAD
However, because of the change introduced in 37ef4c19b4 ("Input: clear
BTN_RIGHT/MIDDLE on buttonpads") the BTN_RIGHT key bit is not mapped
anymore breaking the device right click button and making impossible to
workaround it in user space.
In order to avoid breakage on other present or future devices, revert
the patch causing the issue.
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220321184404.20025-1-jose.exposito89@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e941dc13fd ]
I observed the following problem with the BT404 touch pad
running the Phosh UI:
When e.g. typing on the virtual keyboard pressing "g" would
produce "ggg".
After some analysis it turns out the firmware reports that three
fingers hit that coordinate at the same time, finger 0, 2 and
4 (of the five available 0,1,2,3,4).
DOWN
Zinitix-TS 3-0020: finger 0 down (246, 395)
Zinitix-TS 3-0020: finger 1 up (0, 0)
Zinitix-TS 3-0020: finger 2 down (246, 395)
Zinitix-TS 3-0020: finger 3 up (0, 0)
Zinitix-TS 3-0020: finger 4 down (246, 395)
UP
Zinitix-TS 3-0020: finger 0 up (246, 395)
Zinitix-TS 3-0020: finger 2 up (246, 395)
Zinitix-TS 3-0020: finger 4 up (246, 395)
This is one touch and release: i.e. this is all reported on
touch (down) and release.
There is a field in the struct touch_event called finger_cnt
which is actually a bitmask of the fingers active in the
event.
Rename this field finger_mask as this matches the use contents
better, then use for_each_set_bit() to iterate over just the
fingers that are actally active.
Factor out a finger reporting function zinitix_report_fingers()
to handle all fingers.
Also be more careful in reporting finger down/up: we were
reporting every event with input_mt_report_slot_state(..., true);
but this should only be reported on finger down or move,
not on finger up, so also add code to check p->sub_status
to see what is happening and report correctly.
After this my Zinitix BT404 touchscreen report fingers
flawlessly.
The vendor drive I have notably does not use the "finger_cnt"
and contains obviously incorrect code like this:
if (touch_dev->touch_info.finger_cnt > MAX_SUPPORTED_FINGER_NUM)
touch_dev->touch_info.finger_cnt = MAX_SUPPORTED_FINGER_NUM;
As MAX_SUPPORTED_FINGER_NUM is an ordinal and the field is
a bitmask this seems quite confused.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220228233017.2270599-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5600f69866 upstream.
Syzbot reported warning in usb_submit_urb() which is caused by wrong
endpoint type. There was a check for the number of endpoints, but not
for the type of endpoint.
Fix it by replacing old desc.bNumEndpoints check with
usb_find_common_endpoints() helper for finding endpoints
Fail log:
usb 5-1: BOGUS urb xfer, pipe 1 != type 3
WARNING: CPU: 2 PID: 48 at drivers/usb/core/urb.c:502 usb_submit_urb+0xed2/0x18a0 drivers/usb/core/urb.c:502
Modules linked in:
CPU: 2 PID: 48 Comm: kworker/2:2 Not tainted 5.17.0-rc6-syzkaller-00226-g07ebd38a0da2 #0
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-2 04/01/2014
Workqueue: usb_hub_wq hub_event
...
Call Trace:
<TASK>
aiptek_open+0xd5/0x130 drivers/input/tablet/aiptek.c:830
input_open_device+0x1bb/0x320 drivers/input/input.c:629
kbd_connect+0xfe/0x160 drivers/tty/vt/keyboard.c:1593
Fixes: 8e20cf2bce ("Input: aiptek - fix crash on detecting device without endpoints")
Reported-and-tested-by: syzbot+75cccf2b7da87fb6f84b@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/20220308194328.26220-1-paskripkin@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04b7762e37 upstream.
Before these changes elan_suspend() would only disable the regulator
when device_may_wakeup() returns false; whereas elan_resume() would
unconditionally enable it, leading to an enable count imbalance when
device_may_wakeup() returns true.
This triggers the "WARN_ON(regulator->enable_count)" in regulator_put()
when the elan_i2c driver gets unbound, this happens e.g. with the
hot-plugable dock with Elan I2C touchpad for the Asus TF103C 2-in-1.
Fix this by making the regulator_enable() call also be conditional
on device_may_wakeup() returning false.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220131135436.29638-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81a36d8ce5 upstream.
elan_disable_power() is called conditionally on suspend, where as
elan_enable_power() is always called on resume. This leads to
an imbalance in the regulator's enable count.
Move the regulator_[en|dis]able() calls out of elan_[en|dis]able_power()
in preparation of fixing this.
No functional changes intended.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220131135436.29638-1-hdegoede@redhat.com
[dtor: consolidate elan_[en|dis]able() into elan_set_power()]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 73cca71a90 ]
As reported by the STEPCONFIG[1-16] registered field descriptions of the
TI reference manual, for the ADC "in single ended, SEL_INM_SWC_3_0 must
be 1xxx".
Unlike the Y and Z coordinates, this bit has not been set for the step
configuration registers used to sample the X coordinate.
Fixes: 1b8be32e69 ("Input: add support for TI Touchscreen controller")
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Link: https://lore.kernel.org/r/20211212125358.14416-2-dariobin@libero.it
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37ef4c19b4 ]
Buttonpads are expected to map the INPUT_PROP_BUTTONPAD property bit
and the BTN_LEFT key bit.
As explained in the specification, where a device has a button type
value of 0 (click-pad) or 1 (pressure-pad) there should not be
discrete buttons:
https://docs.microsoft.com/en-us/windows-hardware/design/component-guidelines/touchpad-windows-precision-touchpad-collection#device-capabilities-feature-report
However, some drivers map the BTN_RIGHT and/or BTN_MIDDLE key bits even
though the device is a buttonpad and therefore does not have those
buttons.
This behavior has forced userspace applications like libinput to
implement different workarounds and quirks to detect buttonpads and
offer to the user the right set of features and configuration options.
For more information:
https://gitlab.freedesktop.org/libinput/libinput/-/merge_requests/726
In order to avoid this issue clear the BTN_RIGHT and BTN_MIDDLE key
bits when the input device is register if the INPUT_PROP_BUTTONPAD
property bit is set.
Notice that this change will not affect udev because it does not check
for buttons. See systemd/src/udev/udev-builtin-input_id.c.
List of known affected hardware:
- Chuwi AeroBook Plus
- Chuwi Gemibook
- Framework Laptop
- GPD Win Max
- Huawei MateBook 2020
- Prestigio Smartbook 141 C2
- Purism Librem 14v1
- StarLite Mk II - AMI firmware
- StarLite Mk II - Coreboot firmware
- StarLite Mk III - AMI firmware
- StarLite Mk III - Coreboot firmware
- StarLabTop Mk IV - AMI firmware
- StarLabTop Mk IV - Coreboot firmware
- StarBook Mk V
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Link: https://lore.kernel.org/r/20220208174806.17183-1-jose.exposito89@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf73ed894e ]
Since irq request is the last thing in the driver probe, it happens
later than the input device registration. This means that there is a
small time window where if the open method is called the driver will
attempt to enable not yet available irq.
Fix that by moving the irq request before the input device registration.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Fixes: 26822652c8 ("Input: add zinitix touchscreen driver")
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20220106072840.36851-2-nikita@trvn.ru
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9222ba68c3 ]
We've got a bug report about the non-working keyboard on ASUS ZenBook
UX425UA. It seems that the PS/2 device isn't ready immediately at
boot but takes some seconds to get ready. Until now, the only
workaround is to defer the probe, but it's available only when the
driver is a module. However, many distros, including openSUSE as in
the original report, build the PS/2 input drivers into kernel, hence
it won't work easily.
This patch adds the support for the deferred probe for i8042 stuff as
a workaround of the problem above. When the deferred probe mode is
enabled and the device couldn't be probed, it'll be repeated with the
standard deferred probe mechanism.
The deferred probe mode is enabled either via the new option
i8042.probe_defer or via the quirk table entry. As of this patch, the
quirk table contains only ASUS ZenBook UX425UA.
The deferred probe part is based on Fabio's initial work.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1190256
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Samuel Čavoj <samuel@cavoj.net>
Link: https://lore.kernel.org/r/20211117063757.11380-1-tiwai@suse.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e1f5e84820 upstream.
Some automated builds report a stack frame size in excess of 2 kB for
iqs626_probe(); the culprit appears to be the call to iqs626_parse_prop().
To solve this problem, specify noinline_for_stack for all of the
iqs626_parse_*() helper functions which are called inside a for loop
within iqs626_parse_prop().
As a result, a build with '-Wframe-larger-than' as low as 512 is free of
any such warnings.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20211129004104.453930-1-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2667f6b7af ]
I have a ST1633 touch controller which fails to probe due to a timeout
waiting for the controller to become ready. Increasing the minimum
delay to 100ms ensures that the probe sequence completes successfully.
The ST1633 datasheet says nothing about the maximum delay here and the
ST1232 I2C protocol document says "wait until" with no notion of a
timeout.
Since this only runs once during probe, being generous with the timout
seems reasonable and most likely the device will become ready
eventually.
(It may be worth noting that I saw this issue with a PREEMPT_RT patched
kernel which probably has tighter wakeups from usleep_range() than other
preemption models.)
Fixes: f605be6a57 ("Input: st1232 - wait until device is ready before reading resolution")
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210929152609.2421483-1-john@metanate.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c4c2c8e6f ]
Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding a SPI device ID table.
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210927134104.38648-1-broonie@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
